aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2005-04-24[PATCH] SCSI GFP fixesAl Viro
Somebody forgot that | has higher priority than ?:. As the result, allocation is done with bogus flags - instead of GFP_ATOMIC + possibly GFP_DMA we always get GFP_DMA and no GFP_ATOMIC. Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-22Merge rsync://rsync.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6.gitLinus Torvalds
2005-04-21[SPARC64]: In sunsab driver, make sure to set the uart timeout.David S. Miller
This breaks serial consoles badly. Thanks to Eric Brower for tracking down the problem. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[SPARC64]: In sunsu driver, make sure to fully init chip for kbd/msDavid S. Miller
We were forgetting to call sunsu_change_speed(). The reason that replugging in the mouse cable "fixes things" is that causes a BREAK interrupt which in turn caused a call to sunsu_change_speed() which would get the chip setup properly. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[SPARC]: Provide generic ioctls in Sparc RTC driver.David S. Miller
Provide support for drivers/char/rtc.c ioctls in the Mostek rtc driver as well as the Sparc specific RTCGET and RTCSET. This allows userspace to be much less messy. Currently util-linux and other spots jump through hoops trying various ioctl variants until it hits the right one whatever driver actually being used supports. Eventually all of this should move over to the genrtc.c driver, but not today... While we are here, fix up the register types for sparse. Thanks to Frans Pop for helping point out this issue. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add msi testMichael Chan
Add MSI test for chips that support MSI. If MSI test fails, it will switch back to INTx mode and will print a message asking the user to report the failure. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add msi supportMichael Chan
Add MSI support for 5751 C0 and 5752. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Fix bug in tg3_set_eeprom()Michael Chan
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the offset is not 4-byte aligned. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add nvram lock-out support for 5752 TPMMichael Chan
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out is enabled, certain NVRAM registers cannot be written to. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add nvram detection for 5752Michael Chan
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add GPIO3 for 5752Michael Chan
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as output when it is unused. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Workaround 5752 A0 chip IDMichael Chan
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround it is to change it to the correct value in tp->pci_chip_rev_id. This way, it is easier to check for the ASIC_REV_5752 in the rest of the driver. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Fix tg3_set_power_state()Michael Chan
Fix tg3_set_power_state to drive GPIOs properly based on the TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0 and D3 power state changes. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Setup proper GPIO settingsMichael Chan
Setup proper GPIO settings in tp->grc_local_ctrl before calling tg3_set_power() state in tg3_get_invariants() and after chip reset. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Split tg3_phy_probe into 2 functionsMichael Chan
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling tg3_set_power_state() in tg3_get_invariants(). This will allow tg3_set_power_state() to drive the GPIOs correctly based on the config. information in eeprom. On the 5752, there are no pull-up resistors on the GPIO pins and it is necessary to drive the unused GPIOs as output. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Minor 5752 fixesMichael Chan
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add support for bcm5752 rev a1John W. Linville
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0, and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1 to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: check TG3_FLG2_5750_PLUS flag to set TG3_FLG2_5705_PLUS flagJohn W. Linville
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set TG3_FLG2_5705_PLUS flag. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use TG3_FLG2_57{05,50}_PLUS flags in tg3_get_invariantsJohn W. Linville
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and TG3_FLG2_5750_PLUS flags. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: more use of TG3_FLG2_5705_PLUS flagJohn W. Linville
Rewrite of a couple of troublesome multi-way if statements to use TG3_FLG2_5705_PLUS flag. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use new TG3_FLG2_5750_PLUS flagJohn W. Linville
Replace a number of two-way if statements checking for 5750, and/or 5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: define TG3_FLG2_5750_PLUS flagJohn W. Linville
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for ASIC_REV_5750 or ASIC_REV_5752. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use TG3_FLG2_5705_PLUS instead of multi-way if'sJohn W. Linville
Replace a number of three-way if statements checking for 5705, 5750, and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add bcm5752 entry to pci_ids.hJohn W. Linville
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3. I did this separately in case patches like this (i.e. new PCI IDs) need to come from more "official" sources. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add bcm5752 to tg3_pci_tblJohn W. Linville
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl. Next patch will change entry to use pci_ids.h-based definition. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add basic bcm5752 supportJohn W. Linville
Add ASIC_REV_5752 definition. Track-down all references to ASIC_REV_5750 and mirror them with references to the newly defined ASIC_REV_5752. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[PATCH] Fix tgafb.c compile failureAdrian Bunk
The untested patch below should fix this compile error. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] Fix non-legacy ISO receive regressionJody McIntyre
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's allocation fix. Multichannel ISO receive still sucks; it should be possible to use both legacy and non-legacy modes at the same time, but with this patch, things are no worse than they were in 2.6.11 and allocation is still done at the correct time. Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] ohci1394: tlabels misprinted in DBGMSGJody McIntyre
- Print the correct value in the DBGMSG in dma_rcv_tasklet(). See OHCI 1.1 section 8.7, page 103 ff. - Print tlabels as %d everywhere. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] fix for ISDN ippp filteringKarsten Keil
We do not longer use DLT_LINUX_SLL for activ/pass filters but DLT_PPP_WITHDIRECTION witch need 1 as outbound flag. Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] Fix aic7xxx_osm.c compile with older gcc'sJames Bottomley
My version of gcc doesn't warn about this error (declaration in the middle of a set of statements). The fix is simple (this also corrects return code; for init functions it should be zero or error).
2005-04-19Merge with kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6.git/Linus Torvalds
for 13 driver core, sysfs, and debugfs fixes.
2005-04-19Merge with kernel.org:/pub/scm/linux/kernel/git/gregkh/aoe-2.6.git/Linus Torvalds
for 11 aoe bugfix patches.
2005-04-19Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6.git/Linus Torvalds
2005-04-19Merge with Greg's USB tree at ↵Linus Torvalds
kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6.git/ Yah, it does work to merge. Knock wood.
2005-04-18[PATCH] aoe 12/12: send outgoing packets in orderecashin@coraid.com
I can't use list.h, since sk_buff doesn't have a list_head but instead has two struct sk_buff pointers, and I want to avoid any extra memory allocation. send outgoing packets in order Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 11/12: add support for disk statisticsecashin@coraid.com
add support for disk statistics Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 6/12: Alexey Dobriyan sparse cleanupecashin@coraid.com
Alexey Dobriyan sparse cleanup Signed-off-by: Alexey Dobriyan <adobriyan@mail.ru> Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 5/12: don't try to free null bufpoolecashin@coraid.com
don't try to free null bufpool Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 3/12: update driver version to 6ecashin@coraid.com
update driver version to 6 Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 2/12: allow multiple aoe devices with same MACecashin@coraid.com
allow multiple aoe devices with same MAC addr Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] aoe 1/12: remove too-low cap on minor numberecashin@coraid.com
remove too-low cap on minor number Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] kobject/hotplug split - usb criskay.sievers@vrfy.org
kobject_add() and kobject_del() don't emit hotplug events anymore. We need to do it ourselves now. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] kobject/hotplug split - devices corekay.sievers@vrfy.org
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it ourselves if we are finished populating the device directory. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] kobject/hotplug split - class corekay.sievers@vrfy.org
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it ourselves if we are finished populating the device directory. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] export platform_add_devicesRobert Schwebel
platform_add_devices can be used from within modules, so it should be exported. This can for example happen if you have hotpluggable firmware in an FPGA on a system on chip processor; in our case the FPGA is probed for devices and the FPGA base code registers the devices it has found with the kernel. (akpm: I think this is reasonable from a licensing POV: it's unlikely that anyone would be interested in merging such specialised modules into mainline, and it's a GPL export). Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] add TIMEOUT to firmware_class hotplug eventkay.sievers@vrfy.org
On Tue, 2005-03-15 at 09:25 +0100, Hannes Reinecke wrote: > The current implementation of the firmware class breaks a fundamental > assumption in udevd: that the physical device can be initialised fully > prior to executing the next event for that device. Here we add a TIMEOUT value to the hotplug environment of the firmware requesting event. I will adapt udevd not to wait for anything else, if it finds a TIMEOUT key. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] I2C: Fix incorrect sysfs file permissions in it87 and via686a driversJean Delvare
The it87 and via686a hardware monitoring drivers each create a sysfs file named "alarms" in R/W mode, while they should really create it in read-only mode. Since we don't provide a store function for these files, write attempts to these files will do something undefined (I guess) and bad (I am sure). My own try resulted in a locked terminal (where I attempted the write) and a 100% CPU load until next reboot. As a side note, wouldn't it make sense to check, when creating sysfs files, that readable files have a non-NULL show method, and writable files have a non-NULL store method? I know drivers are not supposed to do stupid things, but there is already a BUG_ON for several conditions in sysfs_create_file, so maybe we could add two more? Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] I2C: via686a cleanupsJean Delvare
Here comes a small cleanup patch for the via686a driver. I noticed the following two non-fatal problems: 1* The device parent is explicitely set, but it's not needed because the i2c core will do as the client is registered. 2* snprintf is used where strlcpy would suffice. Fixing them brings the via686a driver in line with what other similar drivers do. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] w1_smem: w1 ID is only 8 bytes long.johnpol@2ka.mipt.ru
w1 ID is only 8 bytes long. Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-16 11:54:24 +0000