| Age | Commit message (Collapse) | Author |
|---|
|
Anydata is using usb_serial_generic_write_bulk_callback() for its
read URB, but it should use usb_serial_generic_read_bulk_callback()
instead (it's a read URB, isn't it?).
Reported by Jon K Hellan <hellan@acm.org>.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Recent section changes broke gadget builds on some platforms. This patch
is the best fix that's available until better section markings exist:
- There's a lot of cleanup code that gets used in both init and exit paths;
stop marking it as "__exit".
(Best fix for this would be an "__init_or_exit" section marking, putting
the cleanup in __init when __exit sections get discarded else in __exit.)
- Stop marking the use-once probe routines as "__init" since references
to those routines are not allowed from driver structures. They're now
marked "__devinit", which in practice is a net lose.
(Best fix for this is likely to separate such use-once probe routines
from the driver structure ... but in general, all busses that aren't
hotpluggable will be forced to waste memory for all probe-only code.)
In general these broken section rules waste an average of two to four kBytes
per driver of code bloat ... because none of the relevant code can ever be
reused after module initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Please add the attached device to unusual_devs.h.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the Testo USB interface to the list of devices
recognized by the ftdi_sio module. This device is based on a FT232BL
chip, and is used as an interface to get data from digital sensors
(thermometer, etc). See http://www.testo.com/
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and
T5 to cover the H5 as well.
From: Lars Jacob <jacob.lars@googlemail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as748) adds an unusual_devs entry for the Nokia E61 mobile
phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like
the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't
using very good firmware these days...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I just got a "ZyXEL Prestige USB Adapter" that is actually RTL8150
adapter. Here is the relevant /proc/bus/usb/devices output (after
adding the vendor/product IDs to the driver):
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=119 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0586 ProdID=401a Rev= 1.00
S: Manufacturer=ZyXEL
S: Product=Prestige USB Adapter
S: SerialNumber=1027
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=120mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=rtl8150
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
This patch adds the ZyXEL vendor ID to the rtl8150.c driver. The
device has absolutely no identifying marks on the outside for model
type, just a serial number, and I can't find anything on ZyXEL's
website, so I called the product ID PRODUCT_ID_PRESTIGE to match the
product string.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: <petkan@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Yet another "same name, somewhat different hardware" product.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is to get the WiseGroup.,Ltd SmartJoy Dual Plus PS2-to-USB
Adapter [0x6677:0x8802] correctly detected. It sets the NOGET and
MULTI_INPUT quirks to make 2 joystick nodes appear in stead of only
one.
(As of yet, only confirmed working by myself.)
Signed-off-by: Navaho Gunleg <navahogunleg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The below patch fixes the ipw module in kernel 2.6.17 for me; without
this change it simply does not work at all (all but the first writes are
refused because write_urb_busy is always 1).
This problem was there in 2.6.15 as well, but at that point I used the
(updated) ipw.c, version 0.4, from
http://www.neology.co.za/products/opensource/ipwireless/ which no longer
compiles with 2.6.17. It can be made to after a few changes but
obviously it's easier if the built-in ipw driver works instead of having
to download one from the neology site.
From: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Devfs is gone. We can remove that information.
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove destructor and call kmem_cache_create with NULL for the destructor.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Adds configurable waiting periods to the ipaq connection code. These are
not needed when the pocketpc device is running normally when plugged in,
but they need extra delays if they are physically connected while
rebooting.
There are two parameters :
* initial_wait : this is the delay before the driver attemts to start the
connection. This is needed because the pocktpc device takes much
longer to boot if the driver starts sending control packets too soon.
* connect_retries : this is the number of times the control urb is
retried before finally giving up. The patch also adds a 1 second delay
between retries.
I'm not sure if the cases where this patch is useful are general enough
to include this in the kernel.
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes several problems in the ipaq.c driver with connecting
and disconnecting pocketpc devices:
* The read urb stayed active if the connect failed, causing nullpointer
dereferences later on.
* If a write failed, the driver continued as if nothing happened. Now it
handles that case the same way as other usb serial devices (fix by
Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>)
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In a rare and all-but-unused path, the EHCI driver could reuse a variable
in a way that'd make trouble. Specifically, if the first root hub port
gets an overcurrent event (rare) during a remote wakeup scenario (all but
unused in today's Linux, except for folk working with suspend-to-RAM and
similar sleep states), that would look like a fatal error which would shut
down the controller. Fix by not reusing that variable.
Spotted by Per Hallsmark <saxofon@musiker.nu>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6661
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch creates a new driver, sierra.c, that supports the new
non-composite Sierra Wireless WWAN devices. The older Sierra
Wireless and Airprime devices are supported in airprime.c.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
coverity spotted (id #185) that we still use urb, if the allocation
fails in the error path. This patch fixes this by returning directly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Move variables only used on !__hppa__ into that #ifndef section. This
cleans up a compiler warning on parisc. Problem pointed out by
Joel Soete.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.
The original patch was by Guillaume Autran, who in turn based it on the
same mechanism implemented in the 'visor' driver. I (Ian Abbott)
re-targeted the patch to the latest sources, fixed a couple of errors,
renamed his new structure members, and updated the implementations of
the 'write_room' and 'chars_in_buffer' methods to take account of the
number of outstanding 'write' bytes. It seems to work fine, though at
low baud rates it is still possible to queue up an amount of data that
takes an age to shift (a job for another day!).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The anti user-DoS mechanism in the USB serial 'visor' driver can fail in
the following way:
visor_open: priv->outstanding_urbs = 0
visor_write: ++priv->outstanding_urbs
visor_close:
visor_open: priv->outstanding_urbs = 0
visor_write_bulk_callback: --priv->outstanding_urbs
So priv->outstanding_urbs ends up as (unsigned long)(-1). Not good!
I haven't seen this happen with the visor driver as I don't have the
hardware, but I have seen it while testing a patch to implement the same
functionality in the ftdi_sio driver (patch not yet submitted).
The fix is pretty simple: don't reinitialize outstanding_urbs in
visor_open. (Again, I haven't tested the fix in visor, but I have
tested it in ftdi_sio.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:
Don't return status >= 0 when an error occurs;
Clear the port-change-suspend status indicator after
resuming a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.
From: Ernis <ernisv@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.
From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways. It also doesn't return 0 in
all the success pathways. This patch (as724) fixes the behavior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect. It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.
This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
tiny things
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect. This patch (as726)
fixes it.
From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: Matt Meno <mmeno@idealcorp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).
It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
did not go far enough
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I noticed this while debugging something unrelated on
sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?
Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Compile fixes for au1200 ohci.
First part looks a bit hackish... but it works for me.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Joseph Fannin reported that hpet_rtc_interrupt() enables hardirqs
in irq context:
[ 25.628000] [<c014af4e>] trace_hardirqs_on+0xce/0x200
[ 25.628000] [<c036cf21>] _spin_unlock_irq+0x31/0x70
[ 25.628000] [<c0296584>] rtc_get_rtc_time+0x44/0x1a0
[ 25.628000] [<c01198bb>] hpet_rtc_interrupt+0x21b/0x280
[ 25.628000] [<c0161141>] handle_IRQ_event+0x31/0x70
[ 25.628000] [<c0162d37>] handle_edge_irq+0xe7/0x210
[ 25.628000] [<c0106192>] do_IRQ+0x92/0x120
[ 25.628000] [<c0104121>] common_interrupt+0x25/0x2c
the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sparse warnings.
[S390] path grouping and path verifications fixes.
[S390] xpram module parameter parsing.
[S390] cpu_relax() is supposed to have barrier() semantics.
[S390] fix futex_atomic_cmpxchg_inatomic
[S390] subchannel register/unregister mutex.
[S390] raw_local_save_flags/raw_local_irq_restore type check
[S390] __builtin_trap() and gcc version.
|
|
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: Alessio Sangalli <alesan@manoweb.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
