aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2008-11-19Input: pcspkr - fix PIT lockup on some chipsetsZoltan Devai
There've been reports [1] about the sysem bell causing a hard lockup. My machine was affected as well: any speaker output hung the machine completely, nothing in the logs, no magic sysrq, etc., looked like a hardware problem. Had a closer look on the issue, and it turned out that the pcspkr module is responsible. The cause is the bad setup of Timer 2 in the i8253 controller, which probably hangs the whole PIT controller. Intel datasheets [2] state that the timer registers are in an undefined state after reset and they need to be programmed before enabling the timer. (And enabling without programming the frequency first doesn't make sense anyway). I don't know which chipsets are affected (if not all), it also depends on the BIOS whether it initializes the timer (e.g. to beep when you start the machine). The following patch solved the issue on my ICH6 notebook, couldn't test it with any others, but should be safe to apply. [1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/146151 https://bugs.launchpad.net/ubuntu/+bug/270790 http://ubuntuforums.org/showthread.php?t=227693 http://bugs.gentoo.org/show_bug.cgi?id=222583 https://bugzilla.redhat.com/show_bug.cgi?id=454225 [2] http://www.intel.com/assets/pdf/datasheet/252516.pdf http://www.intel.com/assets/pdf/datasheet/301473.pdf http://www.intel.com/design/chipsets/datashts/29065503.pdf Signed-off-by: Zoltan Devai <zdevai@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-11-19Input: usbtouchscreen - fix TSC-10 DM USB controllers without EEPROMNuno Lucas
The usbtouchscreen module implements a driver for the TSC-10 DM USB touchscreen controllers, but assumes a 2-byte response for the CMD_RESET and CMD_RATE commands, when they can be only a single byte when no EEPROM is connected. The driver worked with an earlier controller revision, but new revisions of the controller fail. It seems the problem is that the early controller had the SEL4/EEPROM-CS pin high, but the new controller has it down, making the response different. Without the fix, the controller would answer the single byte 0x06 (ACK), making the init fail with -ENODEV because buf[1] is 0xFF (as initialized before). As the single byte is the only thing we need to check it was ok, there is no need to verify the second byte. The [0x15 0x01] case is the NAK [0x15] response for when there is no data in the EEPROM [bit-0 of second byte set], so I let that be, as I don't have any controller with an EEPROM. With this patch, both the earlier and latest controller work the same. Note: This was previously submited as BUG #11961 [1] on the bugzilla tracker, but rebased to version 2.6.27.4 and with unnecessary comments and printk's removed. [1] http://bugzilla.kernel.org/show_bug.cgi?id=11961 Signed-off-by: Nuno Lucas <ntlucas@gmail.com> Acked-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-30Input: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-29Input: omap-keypad - allow more than 6 rowsPeter Ujfalusi
There is no reason to limit the GPIO rows to 6 for OMAP2. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-29Input: omap-keypad - interrupt disable fixPeter Ujfalusi
The GPIO interrupts are disabled several times after the first key press. No need to disable - again - the interrupts in the omap_kp_scan_keypad function on OMAP2. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-29Input: appletouch - driver refactoringStelian Pop
The appletouch driver has grown up from supporting only a couple of touchpads into supporting many touchpads, which can have different number of sensors, different aspect ratios etc. This patch cleans up the current driver code and makes it easy to support the features of each different touchpad. As a side effect, this patch also modifies the 'Y' multiplication factor of the 'geyser3' and 'geyser4' touchpads (found on Core Duo and Core2 Duo MacBook and MacBook Pro laptops) in order to make the touchpad output match the aspect ratio of the touchpad (Y factor changed from 43 to 64). [dtor@mail.ru: make atp_info constant] Signed-off-by: Stelian Pop <stelian@popies.net> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-27Input: gpio-keys - add flag to allow auto repeatDominic Curran
This patch adds a flag to gpio-key driver to turn on the input subsystems auto repeat feature if needed. Signed-off-by: Dominic Curran <dcurran@ti.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-27Input: xilinx_ps2 - various cleanupsJohn Linn
Review comments were incorporated to improve the driver. 1. Some data was eliminated that was not needed. 2. Renaming of variables for clarity. 3. Removed unneeded type casting. 4. Changed to use dev_err rather than other I/O. 5. Merged together some functions. 6. Added kerneldoc format to functions. Signed-off-by: Sadanand <sadanan@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-27Input: refactor evdev 32bit compat to be shareable with uinputPhilip Langdale
Currently, evdev has working 32bit compatibility and uinput does not. uinput needs the input_event code that evdev uses, so let's refactor it so it can be shared. [dtor@mail.ru: add fix for force feedback compat issues] Signed-off-by: Philip Langdale <philipl@overt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-10-27Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: libata: fix NCQ devices behind port multipliers scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map
2008-10-27libata: fix NCQ devices behind port multipliersJens Axboe
For devices behind sata port multipliers, we have to make sure that they share a tag map since all tags for that PMP must be unique. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-27Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits) MIPS: lemote/lm2e: Added io_map_base to pci controller MIPS: TXx9: Make firmware parameter passing more robust MIPS: Markeins: Remove unnecessary define and cleanup comments, etc. MIPS: Markeins: Extract ll_emma2rh_* functions MIPS: Markeins: Remove runtime debug prints MIPS: EMMA: Fold arch/mips/emma/{common,markeins}/irq*.c into markeins/irq.c MIPS: EMMA2RH: Remove emma2rh_gpio_irq_base MIPS: EMMA2RH: Remove emma2rh_sw_irq_base MIPS: EMMA2RH: Remove emma2rh_irq_base global variable MIPS: EMMA2RH: Remove emma2rh_sync on read operation MIPS: EMMA: Move <asm/emma2rh> to <asm/emma> dir MIPS: EMMA: Move arch/mips/emma2rh/ into arch/mips/emma/ MIPS: EMMA: Kconfig reorganization MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors MIPS: RB532: Disable the right device MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel MIPS: TXx9: CONFIG_TOSHIBA_RBTX4939 spelling MIPS: Fix KGDB build error INPUT: sgi_btns: Add license specification MIPS: IP22: ip22-int.c header file weeding. ...
2008-10-27Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: fw-sbp2: fix races firewire: fw-sbp2: delay first login to avoid retries firewire: fw-ohci: initialization failure path fixes firewire: fw-ohci: don't leak dma memory on module removal firewire: fix struct fw_node memory leak firewire: Survive more than 256 bus resets
2008-10-27INPUT: sgi_btns: Add license specificationDmitri Vorobiev
The SGI Volume Button interface driver uses GPL-only symbols platform_driver_unregister and platform_driver_register, but lacks license specification. Thus, when compiled as a module, this driver cannot be installed. This patch fixes this by adding the MODULE_LICENSE() specification. Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: syncookies: fix inclusion of tcp options in syn-ack libertas: free sk_buff with kfree_skb btsdio: free sk_buff with kfree_skb Phonet: do not reply to indication reset packets Phonet: include generic link-layer header size in MAX_PHONET_HEADER
2008-10-27Tidy up addresses in random driversAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-27leds: da903x: fix the building failure of incomplete type of 'work'Eric Miao
The leds-da903x LED driver was missing the proper #include of linux/workqueue.h, but happened to compile on ARM due to implied includes through other header files. We do need the explict include on other architectures (reported at least for x86-64). Reported-tested-and-acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26libertas: free sk_buff with kfree_skbSergio Luis
free sk_buff with kfree_skb, instead of kree Signed-off-by: Sergio Luis <sergio@larces.uece.br> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-26btsdio: free sk_buff with kfree_skbSergio Luis
free sk_buff with kfree_skb, instead of kree Signed-off-by: Sergio Luis <sergio@larces.uece.br> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-26Merge branch 'for-linus' of git://neil.brown.name/mdLinus Torvalds
* 'for-linus' of git://neil.brown.name/md: md: allow extended partitions on md devices. md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state md: use sysfs_notify_dirent to notify changes to md/array_state
2008-10-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: psmouse - add support for Elantech touchpads Input: i8042 - add Blue FB5601 to noloop exception table
2008-10-26Merge branch 'for-linus' of git://git.o-hand.com/linux-mfdLinus Torvalds
* 'for-linus' of git://git.o-hand.com/linux-mfd: mfd: Make WM8400 depend on I2C until SPI is submitted mfd: add missing Kconfig entry for da903x
2008-10-26Merge branch 'for-upstream' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb * 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: uwb: build UWB before USB/WUSB
2008-10-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: Add support for Sony Vaio VGX-TP1E HID: fix lock imbalance in hiddev HID: fix lock imbalance in hidraw HID: fix hidbus/appletouch device binding regression HID: add hid_type to general hid struct HID: quirk for OLED devices present in ASUS G50/G70/G71 HID: Remove "default m" for Thrustmaster and Zeroplus HID: fix hidraw_exit section mismatch HID: add support for another Gyration remote control Revert "HID: Invert HWHEEL mappings for some Logitech mice"
2008-10-26Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: leds-hp-disk: fix build warning ACPI: Oops in ACPI with git latest ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y. toshiba_acpi: always call input_sync() after input_report_switch() ACPI: Always report a sync event after a lid state change ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined i7300_idle: Cleanup based review comments i7300_idle: Disable ioat channel only on platforms where ile driver can load
2008-10-26m68k: Disable Amiga serial console support if modularGeert Uytterhoeven
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings: | drivers/char/amiserial.c: At top level: | drivers/char/amiserial.c:2138: warning: data definition has no type or storage class | drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall' | drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration | drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used because console_initcall() is not defined (nor really sensible) in the modular case. So disable serial console support if the driver is modular. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX hwmon: (abituguru3) Cosmetic whitespace fixes hwmon: (adt7473) Fix voltage conversion routines hwmon: (lm90) Add support for the LM99 16 degree offset hwmon: (lm90) Fix handling of hysteresis value hwmon-vid: Add support for AMD family 10h CPUs hwmon: (w83781d) Fix linking when built-in
2008-10-26r8169: revert "read MAC address from EEPROM on init"Francois Romieu
This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698. The code has both a short existence and an increasing track of failures despite some work to amend it for -rc1. It is not just a matter of reading the eeprom: sometimes the eeprom is read correctly, then the mac address is not written correctly back into the mac registers. Some chipsets seem to work reliably but it is not clear at this point if the code can simply be made to work on a per-chipset basis and post -rc1 is not the place where I want to experiment these things. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26arm ide breakageAl Viro
a) semicolon before the function body is a bad idea b) it's const struct foo, not struct const foo c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver() d) compiling is occasionally useful. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26hwmon: (abituguru3) enable DMI probing feature on AW9D-MAXAlistair John Strachan
Switch the AW9D-MAX over from port probing to the preferred DMI probe method. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-26hwmon: (abituguru3) Cosmetic whitespace fixesAlistair John Strachan
As the probable result of zealous copy/pasting, many supported boards contain sensor names with trailing whitespace. Though this is not a huge problem, it is inconsistent with other sensor names, and with other similar hwmon drivers. Additionally, the DMI nag message added in 2.6.27 was missing a space between two sentence fragments -- might as well clean that up too. Doesn't alter any kernel text, just data. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-26hwmon: (adt7473) Fix voltage conversion routinesJean Delvare
Fix voltage conversion routines. Based on an earlier patch from Paulius Zaleckas. According to the datasheet voltage is scaled with resistors and value 192 is nominal voltage. 0 is 0V. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Cc: Darrick J. Wong <djwong@us.ibm.com>
2008-10-26hwmon: (lm90) Add support for the LM99 16 degree offsetJean Delvare
The LM99 differs from the LM86, LM89 and LM90 in that it reports remote temperatures (temp2) 16 degrees lower than they really are. So far we have been cheating and handled this in userspace but it really should be handled by the driver directly. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org>
2008-10-26hwmon: (lm90) Fix handling of hysteresis valueJean Delvare
There are several problems in the way the hysteresis value is handled by the lm90 driver: * In show_temphyst(), specific handling of the MAX6646 is missing, so the hysteresis is reported incorrectly if the critical temperature is over 127 degrees C. * In set_temphyst(), the new hysteresis register value is written to the chip but data->temp_hyst isn't updated accordingly, so there is a short period of time (up to 2 seconds) where the old hystereris value will be returned while the new one is already active. * In set_temphyst(), the critical temperature which is used as a base to compute the value of the hysteresis register lacks device-specific handling. As a result, the value of the hysteresis register might be incorrect for the ADT7461 and MAX6646 chips. Fix these 3 bugs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Nate Case <ncase@xes-inc.com>
2008-10-26hwmon-vid: Add support for AMD family 10h CPUsJean Delvare
The AMD family 10h CPUs use the same VID decoding table as the family 0Fh CPUs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz>
2008-10-26hwmon: (w83781d) Fix linking when built-inGeert Uytterhoeven
When w83781d is built-in, the final links fails with the following vague error message: `.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o w83781d_isa_unregister() cannot be marked __exit, as it's also called from sensors_w83781d_init(), which is marked __init. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-26firewire: fw-sbp2: fix racesJay Fenlason
1: There is a small race between queue_delayed_work() and its corresponding kref_get(). Do the kref_get first, and _put it again if the queue_delayed_work() failed, so there is no chance of the kref going to zero while the work is scheduled. 2: An SBP2_LOGOUT_REQUEST could be sent out with a login_id full of garbage. Initialize it to an invalid value so we can tell if we ever got a valid login_id. 3: The node ID and generation may have changed but the new values may not yet have been recorded in lu and tgt when the final logout is attempted. Use the latest values from the device in sbp2_release_target(). Signed-off-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-26firewire: fw-sbp2: delay first login to avoid retriesStefan Richter
This optimizes firewire-sbp2's device probe for the case that the local node and the SBP-2 node were discovered at the same time. In this case, fw-core's bus management work and fw-sbp2's login and SCSI probe work are scheduled in parallel (in the globally shared workqueue and in fw-sbp2's workqueue, respectively). The bus reset from fw-core may then disturb and extremely delay the login and SCSI probe because the latter fails with several command timeouts and retries and has to be retried from scratch. We avoid this particular situation of sbp2_login() and fw_card_bm_work() running in parallel by delaying the first sbp2_login() a little bit. This is meant to be a short-term fix for https://bugzilla.redhat.com/show_bug.cgi?id=466679. In the long run, the SCSI probe, i.e. fw-sbp2's call of __scsi_add_device(), should be parallelized with sbp2_reconnect(). Problem reported and fix tested and confirmed by Alex Kanavin. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-26firewire: fw-ohci: initialization failure path fixesStefan Richter
Fix leaks when pci_probe fails. Simplify error log strings. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-26firewire: fw-ohci: don't leak dma memory on module removalJay Fenlason
The transmit and receive context dma memory was not being freed on module removal. Neither was the config rom memory. Fix that. The ab->next assignment is pure paranoia. Signed-off-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-26firewire: fix struct fw_node memory leakJay Fenlason
With the bus_resets patch applied, it is easy to see this memory leak by repeatedly resetting the firewire bus while running slabtop in another window. Just watch kmalloc-32 grow and grow... Signed-off-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-26firewire: Survive more than 256 bus resetsJay Fenlason
The "color" is used during the topology building after a bus reset, hovever in "struct fw_node"s it is stored in a u8, but in struct fw_card it is stored in an int. When the value wraps in one struct, but not the other, disaster strikes. Signed-off-by: Jay Fenlason <fenlason@redhat.com> Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10922. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-10-25Merge branch 'i7300_idle' into releaseLen Brown
2008-10-25leds-hp-disk: fix build warningLen Brown
drivers/leds/leds-hp-disk.c:59: warning: passing argument 4 of ‘acpi_evaluate_integer’ from incompatible pointer type Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-25ACPI: Oops in ACPI with git latestRafael J. Wysocki
ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [20080926] ACPI Warning (nspredef-0252): \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, expected 4 [20080926] ACPI Error (nspredef-0163): \_SB_.PCI0._OSC: Missing expected return value [20080926] BUG: unable to handle kernel NULL pointer dereference at 00000000 IP: [<c0237671>] acpi_run_osc+0xa1/0x170 Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-25ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.Rafael J. Wysocki
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-25toshiba_acpi: always call input_sync() after input_report_switch()Len Brown
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-25ACPI: Always report a sync event after a lid state changeGuillem Jover
Currently not always an EV_SYN event is reported to userland after the EV_SW SW_LID event has been sent. This is easy to verify by using “input-events” from input-utils and just closing and opening the lid. Signed-off-by: Guillem Jover <guillem.jover@nokia.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-25ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.cMiao Xie
When trying to build 2.6.28-rc1 on ia64, make aborts with: CC drivers/acpi/processor_perflib.o drivers/acpi/processor_perflib.c:41:28: error: asm/cpufeature.h: No such file or directory drivers/acpi/processor_perflib.c: In function ‘acpi_processor_get_performance_info’: drivers/acpi/processor_perflib.c:364: error: implicit declaration of function ‘boot_cpu_has’ drivers/acpi/processor_perflib.c:364: error: ‘X86_FEATURE_EST’ undeclared (first use in this function) drivers/acpi/processor_perflib.c:364: error: (Each undeclared identifier is reported only once drivers/acpi/processor_perflib.c:364: error: for each function it appears in.) make[2]: *** [drivers/acpi/processor_perflib.o] Error 1 make[1]: *** [drivers/acpi] Error 2 make: *** [drivers] Error 2 this patch fix it. Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Acked-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-24i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not definedVenki Pallipadi
When I7300_idle driver is not configured, there is a compile time warning about IDLE_IOAT_CHANNEL not defined. Fix it. Reported-by: Suresh Siddha <suresh.b.siddha@intel.com> Reported-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-18 08:53:24 +0000