| Age | Commit message (Collapse) | Author |
|---|
|
Fix libata kernel-doc parameter:
Warning(linux-2.6.25-rc2-git3//drivers/ata/libata-scsi.c:845): No description found for parameter 'rq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
this will fix crash bug when doing rmmod to the driver, this is because the
port_stop function get called later and it could access the device's registers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch implements libata.force module parameter which can
selectively override ATA port, link and device configurations
including cable type, SATA PHY SPD limit, transfer mode and NCQ.
For example, you can say "use 1.5Gbps for all fan-out ports attached
to the second port but allow 3.0Gbps for the PMP device itself, oh,
the device attached to the third fan-out port chokes on NCQ and
shouldn't go over UDMA4" by the following.
libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
this fixes crash bug as the iomap table is not valid for integrated controllers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The sata_mv driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use ld_qdi and ld_winbond to avoid shadowing static int
variables qdi and winbond. The ld_ prefix refers to
legacy_data.
drivers/ata/pata_legacy.c:777:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:811:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:848:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:882:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:1040:21: warning: symbol 'winbond' shadows an earlier one
drivers/ata/pata_legacy.c:129:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: fix missing casts that produced a warning.
agp: add support for 662/671 to agp driver
fix historic ioremap() abuse in AGP
agp/sis: Suspend support for SiS AGP
agp/sis: Clear bit 2 from aperture size byte as well
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/sis: add pciid for SiS 662/671 chipset
drm: add new rv380 pciid
drm: add support for passing state into the suspend hooks.
drm/i915: Fix hibernate save/restore of VGA attribute regs
drm/i915 more registers for S3 (DSPCLK_GATE_D, CACHE_MODE_0, MI_ARB_STATE)
drm/i915: restore pipeconf regs unconditionally
drm/i915: save/restore interrupt state
drm: convert drm from nopage to fault.
i915: wrap chipset types requiring hw status set ioctl
drm/radeon: add initial rs690 support to drm.
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
fix i915 driver to use state for hibernate save avoidance.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes two NULL dereferences introduced by commit
06386bbfd2441416875d0403d405c56822f6ebac and spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Free correct MPT on error exit from mthca_fmr_alloc()
IPoIB/cm: Fix ipoib_cm_dev_stop() cleanup when drain times out
|
|
In hibernate, we may end up calling the VGA save regs function twice, so we need to make sure it's idempotent. That means leaving ARX in index mode after the first save operation. Fixes hibernate on 965.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Failing to preserve the MI_ARB_STATE register was causing FIFO underruns on
the VGA output on my HP 2510p after resume.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On many chipsets, the checks for DPLL enable or VGA mode will prevent the pipeconf regs from being restored, which could result in a blank display or X failing to come back after resume. So restore them unconditionally along with actually restoring pipe B's palette correctly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On resume, if the interrupt state isn't restored correctly, we may end
up with a flood of unexpected or ill-timed interrupts, which could cause
the kernel to disable the interrupt or vblank events to happen at the
wrong time. So save/restore them properly.
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Remove redundant vma range checks.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Also applys to recent added new chipset.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
This adds support for configuring the RS690 GART.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When mthca_fmr_alloc() returns an error, it should free the MPT at the
index key, not mr->ibmr.lkey, since the lkey has been mangled by
hw_index_to_key() and no longer is the real index. This bug causes
corruption of the MPT table free bitmap when mthca_fmr_alloc() fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit efcd9971 ("IPoIB/cm: Factor out ipoib_cm_free_rx_reap_list()")
introduced a bug in ipoib_cm_dev_stop() when the receive drain times
out. In that case, the function moves all the pending rx stuff into a
private list but then calls ipoib_cm_free_rx_reap_list(), which
handles a different list.
Fix this by moving everything to the rx_reap_list that will actually
get freed up.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=906>.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] qdio: FCP/SCSI write I/O stagnates on LPAR
[S390] Fix futex_atomic_cmpxchg_std inline assembly.
[S390] dcss: Fix Unlikely(x) != y
[S390] sclp: clean up send/receive naming scheme
[S390] etr: fix compile error on !SMP
[S390] qdio: fix qdio_activate timeout handling.
[S390] Initialize per cpu lowcores on cpu hotplug.
[S390] find bit corner case.
[S390] dasd: fix locking in __dasd_device_process_final_queue
[S390] Make sure enabled wait psw is loaded in default_idle.
[S390] Let NR_CPUS default to 32/64 on s390/s390x.
[S390] cio: Do timed recovery on workqueue.
[S390] cio: Remember to initialize recovery_lock.
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
libata: implement drain buffers
libata: eliminate the home grown dma padding in favour of
block: clear drain buffer if draining for write command
block: implement request_queue->dma_drain_needed
block: add request->raw_data_len
block: update bio according to DMA alignment padding
libata: update ATAPI overflow draining
elevator: make elevator_get() attempt to load the appropriate module
cfq-iosched: add hlist for browsing parallel to the radix tree
block: make blk_rq_map_user() clear ->bio if it unmaps it
fs/block_dev.c: remove #if 0'ed code
make struct def_blk_aops static
make blk_settings_init() static
make blk_ioc_init() static
make blk-core.c:request_cachep static again
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] HP ProLiant WatchDog driver
[WATCHDOG] blackfin Watchdog driver: relocate all strings used in __init functions to __initdata
[WATCHDOG] Convert mtx1 wdt to be a platform device and use generic GPIO API
[WATCHDOG] Add support for SB1 hardware watchdog
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add regs_return_value().
[SPARC64]: Kill pcic_present().
[SPARC]: Kill 'prom_palette'.
[ATYFB]: Kill 'prom_palette' sparc code.
[SPARC64]: Kill 'prom_keyboard'.
[SPARC]: Kill extern decl of 'panic_setup'.
[SPARC64]: Delete 'boot_flags'.
[SPARC64]: Kill unused function 'kernel_enter_debugger'.
[SPARC64] arch/sparc64/kernel/unaligned.c: Use time_* macros
[SPARC64]: Always register a PROM based early console.
[SPARC64]: Update defconfig.
[SPARC64]: Add -mtune=ultrasparc3 if possible.
[SPARC64]: Remove Makefile code for ancient gcc and binutils.
[SPARC64]: Remove DEBUG_BOOTMEM.
[SPARC64]: Use shorter "get_zeroed_page" call.
[SPARC]: Use shorter form of "get_zeroed_page".
[SPARC]: video/cg14.c and video/sbuslib.c build fixes
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
[NIU]: Bump driver version and release date.
[NIU]: Fix BMAC alternate MAC address indexing.
net: fix kernel-doc warnings in header files
[IPV6]: Use BUG_ON instead of if + BUG in fib6_del_route.
[IPV6]: dst_entry leak in ip4ip6_err. (resend)
bluetooth: do not move child device other than rfcomm
bluetooth: put hci dev after del conn
[NET]: Elminate spurious print_mac() calls.
[BLUETOOTH] hci_sysfs.c: Kill build warning.
[NET]: Remove MAC_FMT
net/8021q/vlan_dev.c: Use print_mac.
[XFRM]: Fix ordering issue in xfrm_dst_hash_transfer().
[BLUETOOTH] net/bluetooth/hci_core.c: Use time_* macros
[IPV6]: Fix hardcoded removing of old module code
[NETLABEL]: Move some initialization code into __init section.
[NETLABEL]: Shrink the genl-ops registration code.
[AX25] ax25_out: check skb for NULL in ax25_kick()
[TCP]: Fix tcp_v4_send_synack() comment
[IPV4]: fix alignment of IP-Config output
Documentation: fix tcp.txt
...
|
|
If running on LPAR, qdio might overlook an incoming buffer in certain
scenarios. The patch makes sure that incoming buffers are detected
immediately in all situations.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fix Unlikely(x) != y
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Make state change events adjust the correct mask by cleaning up
naming inconsistencies. Also remove chance for lockup by removing
unnecessary mask related check before reading events.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Current code in qdio_activate waits for at least 5 seconds
until it returns. It may return earlier if an error occurs,
but not if everything is ok. This large timeout value
became visible with commit dfa77f611ff295598e218aa0eb6efa73a5cf26d0
"qdio: set QDIO_ACTIVATE_TIMEOUT to 5s", which intended to
fix the timeout value which was zero. In turn setting an
FCP adapter online took 5 seconds.
In practice waiting for 5ms before continuing is sufficient
as pointed out by Utz Bacher and Cornelia Huck.
Cc: Utz Bacher <utz.bacher@de.ibm.com>
Cc: Jan Glauber <jan.glauber@de.ibm.com>
Cc: Ursula Braun <braunu@de.ibm.com>
Cc: Martin Peschke <mp3@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
After setting the status of the cqr and releasing the lock for the
block cqr queue, we call the cqr callback function, which will usually
just trigger the dasd_block_tasklet. But when the tasklet is already
running the cqr might be processed before we invoke the callback
function. In rare cases the callback pointer may already be invalid
by the time we want to call it, which will result in a panic.
Solution: Call the callback function first and then release the lock.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
We can't do our recovery in softirq context, so we schedule it from
our timer function.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This just updates the libata slave configure routine to take advantage
of the block layer drain buffers. It also adjusts the size lengths in
the atapi code to add the drain buffer to the DMA length so the driver
knows it can rely on it.
I suspect I should also be checking for AHCI as well as ATA_DEV_ATAPI,
but I couldn't see how to do that easily.
tj: * atapi_drain_needed() added such that draining is applied to only
misc ATAPI commands.
* q->bounce_gfp used when allocating drain buffer.
* Now duplicate ATAPI PIO drain logic dropped.
* ata_dev_printk() used instead of sdev_printk().
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
With padding and draining moved into it, block layer now may extend
requests as directed by queue parameters, so now a request has two
sizes - the original request size and the extended size which matches
the size of area pointed to by bios and later by sgs. The latter size
is what lower layers are primarily interested in when allocating,
filling up DMA tables and setting up the controller.
Both padding and draining extend the data area to accomodate
controller characteristics. As any controller which speaks SCSI can
handle underflows, feeding larger data area is safe.
So, this patch makes the primary data length field, request->data_len,
indicate the size of full data area and add a separate length field,
request->raw_data_len, for the unmodified request size. The latter is
used to report to higher layer (userland) and where the original
request size should be fed to the controller or device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
For misc ATAPI commands which transfer variable length data to the
host, overflow can occur due to application or hardware bug. Such
overflows can be ignored safely as long as overflow data is properly
drained. libata HSM implementation has this implemented in
__atapi_pio_bytes() and recently updated for 2.6.24-rc but it requires
further improvements. Improve drain logic such that...
* Report overflow errors using ehi desc mechanism instead of printing
directly.
* Properly calculate the number of bytes to be drained considering
actual number of consumed bytes for partial draining.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BMAC port alternate MAC address index needs to start at 1. Index 0 is
used for the main MAC address.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several AGP drivers right now use ioremap_nocache() on kernel ram in order
to turn a page of regular memory uncached.
There are two problems with this:
1) This is a total nightmare for the ioremap() implementation to keep
various mappings of the same page coherent.
2) It's a total nightmare for the AGP code since it adds a ton of
complexity in terms of keeping track of 2 different pointers to
the same thing, in terms of error handling etc etc.
This patch fixes this by making the AGP drivers use the new
set_memory_XX APIs instead.
Note: amd-k7-agp.c is built on Alpha too, and generic.c is built
on ia64 as well, which do not yet have the set_memory_*() APIs,
so for them some we have a few ugly #ifdefs - hopefully they'll
be fixed soon.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Tested on M650 chipset
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
SiS M650 has aperture size byte 0x44
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes the missing residual count setting in DMA mode,
which was introduced during the conversion to blk-end-request.
The residual count could be used by the request submitter.
So if it isn't set correctly, some upper layers does not work.
(e.g. wodim for CD burning.)
The bug is in only DMA mode.
In PIO mode, we are setting the residual count correctly,
so no need to fix.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Andreas Schwab <schwab@suse.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Laura Garcia <nevola@gmail.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Prefetch needs to be set for some ide devices to work when connected to
a ht6560b interface. This was not always done properly, causing a system
with a HD and CD on the primary interface to not work properly. Or, in
effect, hang hard.
This patch forces prefetch on devices before checking whether it
is necessary to change the settings in the interface
This patch should also be applied to 2.4. I don't currently have a
2.4 tree around.
(also change my email address)
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
According to the datasheet, ht6560b only supports up to PIO mode 4.
[bart: manually ported it over 2.6.25-rc2]
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
[bart: manually ported it over via82cxxx changes]
From: Andrew Smith <asmith@tranquility.fsbusiness.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
commit 8ac4ce742c66100931b6f2d7a36b0df08bc721fe ("ide: fix host drivers
depending on ide_generic to probe for interfaces (take 2)") moved probing
to falconide but forgot to take care of Atari specific locking - fix it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
