| Age | Commit message (Collapse) | Author |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPSEC]: Fix the address family to refer encap_family
[IPSEC]: changing API of xfrm6_tunnel_register
[IPSEC]: make sit use the xfrm4_tunnel_register
[IPSEC]: Changing API of xfrm4_tunnel_register.
[TCP]: Prevent pseudo garbage in SYN's advertized window
[NET_SCHED]: sch_hfsc: replace ASSERT macro by WARN_ON
[BRIDGE] br_if: Fix oops in port_carrier_check
[NETFILTER]: Clear GSO bits for TCP reset packet
[TG3]: Update copyright, version, and reldate.
[TG3]: Add some tx timeout debug messages.
[TG3]: Use constant for PHY register 0x1e.
[TG3]: Power down 5704 serdes transceiver when shutting down.
[TG3]: 5906 doesn't need to switch to slower clock.
[TG3]: 5722/5756 don't need PHY jitter workaround.
[TG3]: Use lower DMA watermark for 5703.
[TG3]: Save MSI state before suspend.
[XFRM]: Fix IPv4 tunnel mode decapsulation with IPV6=n
[IPV6] HASHTABLES: Use appropriate seed for caluculating ehash index.
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (61 commits)
[POWERPC] Use udbg_early_init() on ppc32
[POWERPC] Open Firmware serial port driver
[POWERPC] Move MPIC smp routines into mpic.c
[POWERPC] Cleanup pseries kexec code
[POWERPC] Cleanup pseries smp initialisation code
[POWERPC] Consolidate pseries platform header files into pseries.h
[POWERPC] 85xx: Drop use of SYNC macro in head_fsl_booke.S
[POWERPC] cell: pm_rtas_activat_signals routine cleanup
[POWERPC] cell: PPU Oprofile cleanup patch
[POWERPC] spufs: avoid accessing kernel memory through mmapped /mem node
[POWERPC] spu sched: static timeslicing for SCHED_RR contexts
[POWERPC] spu sched: use DECLARE_BITMAP
[POWERPC] spu sched: forced preemption at execution
[POWERPC] spu sched: update some comments
[POWERPC] spu sched: simplity spu_remove_from_active_list
[POWERPC] spufs: optimize spu_run
[POWERPC] spufs: runqueue simplification
[POWERPC] spufs: move prio to spu_context
[POWERPC] spufs: state_mutex cleanup
[POWERPC] spufs: simplify state_mutex
...
|
|
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Stop using i2c_adapter.class_dev
i2c: Remove the warning on missing adapter device
i2c: Declare more i2c_adapter parent devices
i2c: PA Semi SMBus driver
i2c-amd8111: Proposed cleanups
i2c-parport: Add support for One For All remote JP1 interface
i2c-viapro: Add support for the VIA CX700 south bridge
i2c: Add IDs to adapters
i2c: Update the list of bus IDs
i2c: Add driver suspend/resume/shutdown support
i2c: completion header cleanups
i2c-i801: Document the SMBus unhiding quirk
i2c-i801: Spelling fix
i2c: Fix typo in SMBus Write Word Data description
i2c-piix4: Add support for the ATI SB600
i2c-nforce2: Drop unused reference to pci_dev
i2c/vt8231: Remove superfluous initialization
i2c-ali1563: Fix device initialization
i2c-ali1563: Improve the status messages
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (23 commits)
[WATCHDOG] timers cleanup
[WATCHDOG] ib700wdt.c - convert to platform_device part 2
[WATCHDOG] ib700wdt.c - convert to platform_device
[WATCHDOG] ib700wdt.c spinlock/WDIOC_SETOPTIONS changes
[WATCHDOG] ib700wdt.c small clean-up's
[WATCHDOG] ib700wdt.c clean-up init and exit routines
[WATCHDOG] ib700_wdt.c stop + set_heartbeat operations
[WATCHDOG] show default value for nowayout in module parameter
[WATCHDOG] advantechwdt.c - convert to platform_device part 2
[WATCHDOG] advantechwdt.c - convert to platform_device
[WATCHDOG] advantechwdt.c - move set_heartbeat to a seperate function
[WATCHDOG] advantechwdt.c - cleanup before platform_device patches
[WATCHDOG] acquirewdt.c - convert to platform_device part 2
[WATCHDOG] acquirewdt.c - convert to platform_device
[WATCHDOG] acquirewdt.c - clean before platform_device patches
[WATCHDOG] pcwd_usb.c - get heartbeat from dip switches
[WATCHDOG] pcwd.c - e-mail adres update
[WATCHDOG] pcwd_usb.c - get heartbeat from dip switches
[WATCHDOG] pcwd_usb.c - document includes
[WATCHDOG] pcwd_pci.c - spinlock fixes
...
|
|
Somewhere in the rewrite of the work queues my cleanup of SAK handling
got broken. Maybe I didn't retest it properly or possibly the API
was changing so fast I missed something. Regardless currently
triggering a SAK now generates an ugly BUG_ON and kills the kernel.
Thanks to Alexey Dobriyan <adobriyan@openvz.org> for spotting this.
This modifies the use of SAK_work to initialize it when the data
structure it resides in is initialized, and to simply call
schedule_work when we need to generate a SAK. I update both
data structures that have a SAK_work member for consistency.
All of the old PREPARE_WORK calls that are now gone.
If we call schedule_work again before it has processed it
has generated the first SAK it will simply ignore the duplicate
schedule_work request.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Stop using i2c_adapter.class_dev, as it is going to be removed
soon. Luckily, there are only 4 RTC drivers affected.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
|
|
Now that the i2c_adapter migration plan changed and we are going to
keep i2c_adapter.dev, it's no longer that urgent to add a proper device
to all i2c_adapter drivers. Thus is seems resonable to degrade the
warning asking authors to migrate their driver to a debug message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
|
|
New driver for the PA Semi SMBus interfaces.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Proposed cleanups to the i2c-amd8111 SMBus driver:
* Fold long lines.
* Add an explicit mask when writing the low byte of a word.
* Use I2C_SMBUS_BLOCK_MAX instead of hardcoding 32.
* Discard extra blank lines.
* Use boolean not instead of bitwise not for bit tests, it's clearer.
* Return -EBUSY rather than -1 on I/O resource conflict.
* Fix a race on device registration, initialization should be done
before the bus is registered.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This simple patch adds support to i2c-parport for the One For All remote
JP1 parallel port interfaces which can be found detailed at:
http://www.hifi-remote.com/jp1/hardware.shtml
These allow access to the internal configuration EEPROM on various
remote controls and there are a variety of Windows tools that make use
of this hardware. I have tested this patch with the "simple" parallel
port device and a One For All URC-7562 and confirmed that the data read
using the eeprom i2c driver matches that returned by the Windows "IR"
JP1 tool.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
We do not have any documentation for the CX700, but it was reported
to work fine. Thanks to Claas Langbehn for testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
IDs have been defined but not used by most of the I2C adapters.
By having a unique ID, clients can check for correct connection
during probe.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Driver model updates for the I2C core:
- Add new suspend(), resume(), and shutdown() methods. Use them in the
standard driver model style; document them.
- Minor doc updates to highlight zero-initialized fields in drivers, and
the driver model accessors for "clientdata".
If any i2c drivers were previously using the old suspend/resume calls
in "struct driver", they were getting warning messages ... and will
now no longer work. Other than that, this patch changes no behaviors;
and it lets I2C drivers use conventional PM and shutdown support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
i2c-core and i2c-isa use completions without including
<linux/completion.h>. Fix it.
i2c-powermac includes <linux/completion.h> but doesn't use any
completion. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the ATI SB600 SMBus controller.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans-Frieder Vogt <hfvogt@gmx.net>
|
|
Remove a superfluous initialization from the vt8231 hwmon driver; the
i2c core does this, and the source field will be vanishing soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The i2c-ali1563 initialization looks quite broken to me:
* If the I/O space isn't enabled, we forcibly set 3 bits in
the PCI configuration space instead of just the one enabling
the I/O space.
* After that we pretend to check if the write worked, but we
don't actually read the new value from the register.
* It's probably not a good idea to enable the I/O space if no
base address has been set.
So I propose the following changes to that part of the driver:
* Merge ali1563_enable() into ali1563_setup().
* Check the base address before the I/O space enabled bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Improve the status messages printed by the i2c-ali1563 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
|
|
Update version to 3.73.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print the most useful information during tx timeout to help debug.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set DMA read watermark to 4 on 5703 in PCIX mode. This is needed to
prevent some tx timeouts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following problem:
http://bugzilla.kernel.org/show_bug.cgi?id=7969
The MSI state needs to be saved during suspend. PCI state saved
during tg3_init_one() does not contain valid MSI state because
MSI hasn't been enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
/proc/pmu/info contains AC Power: 0 when booting without battery.
Force AC Power, it will be updated whenever the battery state changes.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Move all the initialized variables to bss.
Mark a version string as const.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
- Use timer macros to set function and data members and to modify
expiration time.
- Use DEFINE_TIMER for single (platform dependent) watchdog timers and
do not init them at run-time in these cases.
- del_timer_sync is common in most cases -- we want to wait for timer
function if it's still running.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Steve Hill <steve@navaho.co.uk>
Cc: Heiko Ronsdorf <hero@ihg.uni-duisburg.de>
Cc: Fernando Fuganti <fuganti@conectiva.com.br>
Cc: Gergely Madarasz <gorgo@itc.hu>
Cc: Ken Hollis <khollis@bitgate.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] remove __io_virt and mmiowb.
[S390] cio: use ARRAY_SIZE in device_id.c
[S390] cio: Fixup interface for setting options on ccw devices.
[S390] smp_call_function/smp_call_function_on locking.
|
|
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If ps3fb is available, we have to disable display flipping while changing the
audio or video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the PS3 Virtual Frame Buffer Driver.
As the actual graphics hardware cannot be accessed directly by Linux, ps3fb
uses a virtual frame buffer in main memory. The actual screen image is copied
to graphics memory by the GPU on every vertical blank, by making a hypervisor
call.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fb_videomode_to_var(): reset the virtual screen parameters when converting
from an fb_videomode to an fb_var_screeninfo.
Without this the old virtual screen parameters are kept. Hence you cannot
switch to a video mode with a lower resolution on frame buffer devices that
don't support virtual screens and panning, as values are not supposed to be
rounded down when they don't fit.
I also reordered the assignments to match the order of the individual members.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fbdev modedb: make more input and output pointer parameters const
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fbdev modedb: Take into account the specified refresh rates for video modes
specified by name, so e.g. all of `720p', `720p@60', and `720p@50' work.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the PS3 AV Settings Driver.
The AV Settings driver is used to control Audio and Video settings. It
communicates with the policy manager through the virtual uart.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PS3: Add a shutdown method to the PS3's virtual uart port driver framework
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change nvidiafb_remove to __devexit to fix MODPOST warnings:
WARNING: drivers/video/nvidia/nvidiafb.o - Section mismatch: reference to
.exit.text:nvidiafb_remove from .data.rel.local after 'nvidiafb_driver' (at
offset 0x28)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-By: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use kzalloc instead of kmalloc + memset(0).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
