| Age | Commit message (Collapse) | Author |
|---|
|
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Corrects spi_imx driver oops during initialization/probing: can't use
drv_data before it's allocated.
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I saw a kernel oops in spidev_remove() when a spidev device was registered
and I unloaded the SPI master driver:
Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01c0c50
Oops: Kernel access of bad area, sig: 11 [#1]
CDSPR
Modules linked in: spi_ppc4xx(-)
NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34
REGS: cec89c30 TRAP: 0300 Not tainted (2.6.27.3izt)
MSR: 00021000 <ME> CR: 24000228 XER: 20000007
DEAR: 00000004, ESR: 00800000
TASK = cf889040[2070] 'rmmod' THREAD: cec88000
GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000
GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c
GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000
GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000
NIP [c01c0c50] spidev_remove+0x1c/0xe4
LR [c01bf9e4] spi_drv_remove+0x2c/0x3c
Call Trace:
[cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c
[cec89d10] [c01859a0] __device_release_driver+0x78/0xb4
[cec89d20] [c0185ab0] device_release_driver+0x28/0x44
[cec89d40] [c0184be8] bus_remove_device+0xac/0xd8
[cec89d60] [c0183094] device_del+0x100/0x194
[cec89d80] [c0183140] device_unregister+0x18/0x30
[cec89da0] [c01bf30c] __unregister+0x20/0x34
[cec89db0] [c0182778] device_for_each_child+0x38/0x74
[cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44
[cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58
[cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx]
[...]
IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch
below helped.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The netmos_9xx5_combo type assumes that PCI SSID provides always the
correct value for the number of parallel and serial ports, but there are
indeed broken devices with wrong numbers, which may result in Oops.
This patch simply adds the check of the array range.
Reference: Novell bnc#447067
https://bugzilla.novell.com/show_bug.cgi?id=447067
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 50f3beb50abe0cc0228363af804e50e710b3e5b0 fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
[libata] pata_rb532_cf: fix signature of the xfer function
[libata] pata_rb532_cf: fix and rename register definitions
ata_piix: add borked Tecra M4 to broken suspend list
|
|
Label fail_unreg is no longer used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).
Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
|
|
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
|
|
When resizing a CQ, MTTs associated with the old CQE buffer were not
freed. As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.
Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.
Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix race condition in state change
ieee1394: fix list corruption (reported at module removal)
firewire: fw-sbp2: another iPod mini quirk entry
ieee1394: sbp2: another iPod mini quirk entry
|
|
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time). This lead to a 2.6.27 regression:
http://bugzilla.kernel.org/show_bug.cgi?id=12120
Where firewire devices that were non spec compliant wouldn't spin up.
Fix this by using the block queue timeout value instead.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
megaraid_sas sets the timeout in its slave configure routine for devices
on special channels. This now needs to update the request queue timeout
in block.
Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
ibmvscsi sets the timeout in its slave configure routine for disk
devices. This now needs to update the request queue timeout in block.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
aacraid updates the timeout in its slave configure routine if it is too
small. This now needs to update the request queue timeout in block.
Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Apple ALU wireless keyboards are bluetooth devices
HID: remove setup mutex, fix possible deadlock
HID: add USB ID for another dual gameron adapter
HID: unignore mouse on unibody macbooks
HID: fix blacklist entries for greenasia/pantherlord
|
|
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The zfcp_scsi_queuecommand was not acting according to the standard
when the respective unit was not available. In this case an -EBUSY was
returned, which is not valid in itself, and in addition scsi_done
was called. This combination is not allowed and was leading to a
double finish of the request and therefor double decrement of the
host_busy counter.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Waiting for the ERP to be finished in a task running in the global
kernel work-queue is a bad idea, especially if the ERP needs to run
another job in this work-queue before it can finish. -> deadlock.
This patch removes the necessity to wait for a finished ERP from the
scan task and moves the job scheduling to the end of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The check of having a valid pointer was performed before the
processing was secured by the lock. Between those two steps the
pointer can turn invalid. During further processing another value is
used (referenced by the pointer described above) as a function pointer
which is never verified to be valid either, resulting under some
circumstances in an invalid function call. This patch is fixing both
issues.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Prevent a SCSI target scan for a rport which have turned invalid
in the meantime.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Aborting a SCSI cmnd might requrie to send a abort_fsf_cmnd. If the
creation of this fsf_req fails an ERR_PTR is returned where a NULL
value would be expected as an error indicator. This ERR_PTR is
dereferenced as valid fsf_req in succeeding processing leading to
an error.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Running two wka_port_get calls in parallel could issue two open_port
requests, overwriting the port handle. Don't issue an open_port
for the state PORT_OPENING, and only read the data from GOOD
responses.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For an incoming RSCN it was checked by the ZFCP_STATUS_PORT_DID_DID
define to re-open a remote port or to test the connection. Since this
define was re-used it was also necessary to replace that define with
ZFCP_STATUS_PORT_PHYS_OPEN.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: serial: add more Onda device ids to option driver
USB: usb-storage: unusual_devs entry for Nikon D2H
USB: storage: unusual_devs entry for Mio C520-GPS
USB: fsl_usb2_udc: Report disconnect before unbinding
USB: fsl_qe_udc: Report disconnect before unbinding
USB: fix SB600 USB subsystem hang bug
Revert "USB: improve ehci_watchdog's side effect in CPU power management"
|
|
This reverts commit e669dae6141ff97d3c7566207f5de3b487dcf837, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the "hpwdt" module is loaded (even if the /dev/watchdog device is not
opened), then kdump does not work. The panic kernel either does not start at
all or crash in various places.
The problem is that hpwdt_pretimeout is registered with register_die_notifier()
with the highest possible priority. Because it returns NOTIFY_STOP, the
crash_nmi_callback which is also registered with register_die_notifier()
is never executed. This causes the shutdown of other CPUs to fail.
Reverting the order is no option: The crash_nmi_callback executes HLT
and so never returns normally. Because of that, it must be executed as
last notifier, which currently is done.
So, that patch returns NOTIFY_OK to keep the crash_nmi_callback executed.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
|
|
Thanks to Domenico Riccio for pointing these out.
Cc: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding.
The patch fixes following badness:
root@b1:~# insmod fsl_usb2_udc.ko
Freescale High-Speed USB SOC Device Controller driver (Apr 20, 2007)
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 26:07:ba:c0:44:33
usb0: HOST MAC 96:81:0c:05:4d:e3
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl-usb2-udc: bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [e10c3454] composite_unbind+0x24/0x15c [g_ether]
LR [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc]
Call Trace:
[df145e80] [ffffff94] 0xffffff94 (unreliable)
[df145eb0] [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc]
[df145ed0] [e10c4c40] usb_composite_unregister+0x3c/0x4c [g_ether]
[df145ee0] [c006bcc0] sys_delete_module+0x130/0x19c
[df145f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().
But mainly the patch fixes following badness:
root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbae4dd3a2d35722668ef2c502a7b8b093
Reported-by: raffaele <ralfconn@tele2.it>
Tested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit f0d781d59cb621e1795d510039df973d0f8b23fc.
It was the wrong thing to do, and does not really do what it said
it did.
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
|
|
Introduced in the "Avoid BUG_ONs on VT switch" commit.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Save/restore HWS_PGA on suspend/resume
drm: move drm vblank initialization/cleanup to driver load/unload
drm/i915: execbuffer pins objects, no need to ensure they're still in the GTT
drm/i915: Always read pipestat in irq_handler
drm/i915: Subtract total pinned bytes from available aperture size
drm/i915: Avoid BUG_ONs on VT switch with a wedged chipset.
drm/i915: Remove IMR masking during interrupt handler, and restart it if needed.
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
|
