| Age | Commit message (Collapse) | Author |
|---|
|
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning. Make sure it's initialized.
Reported by Larry Finger.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The pattern !E && !E->fld is nonsensical. The patch below updates this
according to the assumption that && should be ||. But perhaps another
solution was intended.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@disable and_comm@
expression E;
identifier fld;
@@
- !E && !E->fld
+ !E || !E->fld
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds polling mechanism for Data Link Layer Link Active bit
after turning power on, instead of waiting for 1000 msec. This reduces
reduce the unnecessary long wait.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the error paths in pcie_init to avoid leaking memory.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Some firmware fail to properly configure P2P bridges, leaving them
with invalid bus numbers. In some cases, this happens on some embedded
4xx boards as the result of the kernel allocating different bus space
than the firmware does to host bridges while not setting
pcibios_assign_all_busses() for various reasons. In other cases, it can
just be bogus firmware.
This adds some sanity checking to the PCI probing code. If a bridge is
found whose primary bus number doesn't match the bus it's sitting on,
or whose secondary bus number not strictly above it's primary bus
number, then the bridge bus numbers are deconfigured in the first pass
of pci_scan_bridge() to be re-assigned in the second pass.
Tested-by: "Ayman El-Khashab" <AymanE@tanisys.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The PCI core now manages slot names on behalf of slot detection
and slot hotplug drivers, including the handling of duplicate
slot names.
We can use the fakephp driver to help test the new functionality.
Add a 'dup_slots' module param to force fakephp to create multiple
slots with the same name. We can then verify that the PCI core
correctly renamed the slots.
sapphire:/sys/bus/pci/slots # modprobe fakephp dup_slots
sapphire:/sys/bus/pci/slots # ls
fake fake-10 fake-3 fake-5 fake-7 fake-9
fake-1 fake-2 fake-4 fake-6 fake-8
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Now that the PCI core manages the 'name' for each individual
hotplug driver, and all drivers (except rpaphp) have been converted
to use hotplug_slot_name(), there is no need for the PCI hotplug
core to drag around its own copy of name either.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We do not need to manage our own name parameter, especially since
the PCI core can change it on our behalf, in the case of duplicate
slot names.
Remove 'name' from shpchp's version of struct slot.
This change also removes the unused struct task_event from the
slot structure.
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We no longer need to manage our version of hotplug_slot->name
since the PCI and hotplug core manage it on our behalf.
Update the sn_hp_slot_private_alloc() interface to fill in
the correct name for us, as that function already has all
the parameters needed to determine the name.
Cc: kristen.c.accardi@intel.com
Cc: jpk@sgi.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
rpaphp tends to use slot->name directly everywhere, and doesn't
ever need slot->hotplug_slot->name.
struct hotplug_slot->name is going away, so convert rpaphp directly
manipulate its own slot->name everywhere, and don't bother touching
slot->hotplug_slot->name.
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We do not need to manage our own name parameter, especially since
the PCI core can change it on our behalf, in the case of duplicate
slot names.
Remove 'name' from pciehp's version of struct slot, and remove
unused 'task_list' as well.
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We no longer need to manage our version of hotplug_slot->name
since the PCI and hotplug core manage it on our behalf.
Now, we simply advise the PCI core of the name that we would
like, and let the core take care of the rest.
Additionally, slightly rearrange the members of struct slot
so they are naturally aligned to eliminate holes.
Cc: jbarnes@virtuousgeek.org
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove 'name' from fakephp's struct dummy_slot, as the PCI core
will now manage our slot name for us.
Cc: jbarnes@virtuousgeek.org
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In preparation for cleaning up the various hotplug drivers
such that they don't have to manage their own 'name' parameters
anymore, we provide the following convenience functions:
pci_slot_name()
hotplug_slot_name()
These helpers will be used by individual hotplug drivers.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We no longer need to manage our version of hotplug_slot->name
since the PCI and hotplug core manage it on our behalf.
Now, we simply advise the PCI core of the name that we would
like, and let the core take care of the rest.
Cc: jbarnes@virtuousgeek.org
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We no longer need to manage our version of hotplug_slot->name
since the PCI and hotplug core manage it on our behalf.
Now, we simply advise the PCI core of the name that we would
like, and let the core take care of the rest.
Cc: kristen.c.accardi@intel.com
Cc: scottm@somanetworks.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We do not need to manage our own name parameter, especially since
the PCI core can change it on our behalf, in the case of duplicate
slot names.
Remove 'name' from acpiphp's version of struct slot.
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Prevent callers of pci_create_slot() from registering slots with
duplicate names. This condition occurs most often when PCI hotplug
drivers are loaded on platforms with broken firmware that assigns
identical names to multiple slots.
We now rename these duplicate slots on behalf of the user.
If firmware assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
etc.
This is the permanent fix mentioned in earlier commits d6a9e9b4 and
167e782e (shpchp/pciehp: Rename duplicate slot name...).
We take advantage of the new 'hotplug' parameter in pci_create_slot()
to prevent a slot create/rename race between hotplug drivers and
detection drivers.
Scenario A:
hotplug driver detection driver
-------------- ----------------
pci_create_slot(hotplug=set)
pci_create_slot(hotplug=NULL)
The hotplug driver creates the slot with its desired name, and then
releases the semaphore. Now, the detection driver tries to create
the same slot, but it already exists. We don't care about renaming,
so return the existing slot.
Scenario B:
hotplug driver detection driver
-------------- ----------------
pci_create_slot(hotplug=NULL)
pci_create_slot(hotplug=set)
The detection driver creates the slot with name "X". Then the hotplug
driver tries to create the same slot, but wants the name "Y" instead.
We detect that we're trying to create the same slot and that we also
want a rename, so rename the slot to "Y" and return.
Scenario C:
hotplug driver hotplug driver
-------------- ----------------
pci_create_slot(hotplug=set)
pci_create_slot(hotplug=set)
Two separate hotplug drivers are attempting to claim the slot and
are passing valid hotplug_slot args to pci_create_slot(). We detect
that the slot already has a ->hotplug callback, prevent a rename,
and return -EBUSY.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Convert the pci_hotplug_slot_list_lock, which only protected the
list of hotplug slots, to a pci_hp_mutex which now protects both
interfaces.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Slot detection drivers can co-exist with hotplug drivers. The names
of the detected/claimed slots may be different depending on module
load order.
For legacy reasons, we need to allow hotplug drivers to override
the slot name if a detection driver is loaded first (and they find
the same slots).
Creating and overriding slot names should be an atomic operation,
otherwise you get a locking nightmare as various drivers race to
call pci_create_slot().
pci_create_slot() is already serialized by grabbing the pci_bus_sem.
We update the API and add a 'hotplug' param, which is:
set if the caller is a hotplug driver
NULL if the caller is a detection driver
pci_create_slot() does not actually use the 'hotplug' parameter in this
patch. A later patch will add the logic that uses it.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The GPL exported symbol pci_update_slot_number has been renamed to
pci_renumber_slot. Some of the safety checks were unnecessary and
were removed.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Update pci_hp_register() to take a const char *name parameter.
The motivation for this is to clean up the individual hotplug
drivers so that each one does not have to manage its own name.
The PCI core should be the place where we manage the name.
We update the interface and all callsites first, in a
"no functional change" manner, and clean up the drivers later.
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Sometimes, it's necessary to enable software's ability to quiesce and
reset endpoint hardware with function-level granularity, so provide
support for it.
The patch implement Function Level Reset(FLR) feature following PCI-e
spec. And this is the first step. We would add more generic method, like
D0/D3, to allow more devices support this function.
The patch contains two functions. pcie_reset_function() is the new
driver API, and, contains some action to quiesce a device. The other
function is a helper: pcie_execute_reset_function() just executes the
reset for a particular device function.
Current the usage model is in KVM. Function reset is necessary for
assigning device to a guest, or moving it between partitions.
For Function Level Reset(FLR), please refer to PCI Express spec chapter
6.6.2.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
pci_get_subsys() will decrement the reference count of the device that
it starts searching from. Unfortunately, the pci_find_device() interface
will already have decremented the reference count of the device earlier,
so the device will end up losing all reference counts and be freed.
We can fix this by incrementing the reference count of the device to
start searching from before calling pci_get_subsys().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Currently linux doesn't have any code to set the "MSI supported" bit in
Support Fireld of _OSC. This patch adds the code for that.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If acpi_query_osc() returns other than AE_OK, __pci_osc_support_set()
stops scanning ACPI objects to evaluate _OSC. This prevents subsequent
_OSCs from being evaluated if some of root bridge doesn't have _OSC, for
example. So acpi_query_osc() should return always AE_OK to evaluate all
_OSC.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In current pci_osc_control_set() implementation, once the _OSC control
field is queried, it is never queried again. But the query result can
change depending on the _OSC support field. For example, if PCI Express
Native Hot Plug control depends on ASPM support on a certain platform, a
PCI Express Native Hot Plug Control query would fail before the ASPM
driver was loaded, but it would succeed if the ASPM driver was loaded
first. Therefore, pci_osc_control_set() should query the _OSC control
field every time.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pci_osc_control_set() evaluates _OSC without query for control
bits, unless __pci_osc_support_set() is called beforehand. But as
strongly recommended in PCI firmware specification, it should query
control bits first.
This patch changes pci_osc_control_set() to query control bits first
even if __pci_osc_support_set() is not called beforehand.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix possible race condition on _OSC evaluation.
Current _OSC evaluation code has possible race condition because it
maniputes osc_data linked list or its contents without any lock
mechanism.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
for-next
|
|
Since the ehca device driver does not support dynamic memory add and
remove operations, the driver must explicitly reject such requests in
order to prevent unpredictable behaviors related to existing memory
regions that cover all of memory being used by InfiniBand protocols in
the kernel.
The solution (for now at least) is to add a memory notifier to the
ehca device driver and if a request for dynamic memory add or remove
comes in, ehca will always reject it. The user can add or remove
memory by hot-removing the ehca adapter, performing the memory
operation, and then hot-adding the ehca adapter back.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Because ehca adapters can differ in the maximum number of QPs and CQs
we have to save the maximum number of these ressources per adapter and
not globally per ehca driver. This fix introduces 2 new members to the
shca structure to store the maximum value for QPs and CQs per adapter.
The module parameters are now used as initial values for those
variables. If a user selects an invalid number of CQs or QPs we don't
print an error any longer, instead we will inform the user with a
warning and set the values to the respective maximum supported by the
HW.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a get_rx_csum method. Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA. The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.
This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Multi-protocol adapters support different port types. Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it. Port type
is configured through a sysfs interface. When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
panasonic-laptop uses many acpi_*() functions so it should
depend on ACPI; otherwise there are approximately 70
warnings/errors generated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
OpRegion
Based on analysis and a patch from Matthew Garrett <mjg59@srcf.ucam.org>.
Instruct the ThinkPad ACPI firmware to remove delays on the processing of
backlight brightness changes. This method is present on ThinkPad
Vista-compatible BIOSes with standard ACPI backlight level control.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Trivial fix makes the error message match the code before it (ibm->driver
vs ibm->acpi-driver) better.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Attempt to preserve fan state across sleep and hibernation if the fan
control mode is enabled.
For safety reasons, only the PWM OFF (fan at 100%) or maximum
closed-loop level (level 7) are preserved. If the fan state was set
to anything else, it will not be restored.
Also, should the fan be at PWM OFF mode at resume, it will be left at
that state (but this is extremely unlikely, no ThinkPad firmware was
ever reported to do this).
For reference, the known states used for fan control upon resume by
the firmware are either "auto" or "level 7" depending on whether the
laptop wakes due to normal conditions or a thermal emergency.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=11331
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Hartmann <richih.mailinglist@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Code in `pci_link.c' is calling the internal routine `acpi_ut_evaluate_object'
which is dangerous given that it is passing a NULL pointer when it should
be passing a pointer to a real object. The patch corrects the issue by
having the code call the external routine `acpi_evaluate_object', which
correctly handles a NULL pointer.
Signed-off-by: Don Dugger <donald.d.dugger@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
According to ACPI spec when the status of some device is not present
but functional, the device is valid and the children of this device
should be enumerated. It means that the device should be added to
linux acpi device tree. But the device driver for this device should not
be loaded.
The detailed info can be found in the section 6.3.7 of ACPI 3.0b spec.
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which no
device driver should be loaded (for example, a bridge device.).
Children of this device may be present and valid. OS should continue
enumeration below a device whose _STA returns this bit combination
http://bugzilla.kernel.org/show_bug.cgi?id=3358
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add the DMI check to disable power check in the course of device power
transistion.
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
transition
Maybe the incorrect power state is returned on the bogus bios, which
is different with the real power state. For example: the bios returns D0
state and the real power state is D3. OS expects to set the device to D0
state. In such case if OS uses the power state returned by the BIOS and
checks the device power state very strictly in power transition, the device
can't be transited to the correct power state.
So the boot option of "acpi.power_nocheck=1" is added to avoid checking
the device power in the course of device power transition.
http://bugzilla.kernel.org/show_bug.cgi?id=8049
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Attach the ACPI device to the ACPI handle as early as possible so that OS
can get the corresponding ACPI device by the acpi handle in the course
of getting the power/wakeup/performance flags.
http://bugzilla.kernel.org/show_bug.cgi?id=8049
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Get the device power state in the course of scanning device if the device
power flag is power_managable. i.e. The device has the _PSx/_PRx object.
At the same time before the drivers/acpi/power module is loaded, there is no
relation between acpi_power_resource and acpi device. So the first parameter
of acpi_power_get_state is changed to acpi_handle.
http://bugzilla.kernel.org/show_bug.cgi?id=8049
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The AE_BAD_ADDRESS exception code is now unused in ACPICA.
For linux, it's only used at wmi.c and acer-wmi.c.
I checked both wmi.c and acer-wmi.c, the AE_BAD_ADDRESS exception code
has no special meaning. The parent functions just call AE_SUCCESS() or
AE_FAILURE() to check the return status.
So it's safe to replace AE_BAD_ADDRESS with AE_ERROR.
Signed-off-by Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
