| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.
Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] sata_mv: more S/G fixes
|
|
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Some custom implementations of the xilinx fb can use resolutions other
than 640x480. This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver. Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
ide: use only ->set_pio_mode method for programming PIO modes (take 2)
sis5513: don't change UDMA settings when programming PIO
it8213/piix/slc90e66: don't change DMA settings when programming PIO
alim15x3: PIO mode setup fixes
siimage: fix ->set_pio_mode method to select PIO data transfer
cs5520: don't enable VDMA in ->speedproc
sc1200: remove redundant warning message from sc1200_tune_chipset()
ide-pmac: PIO mode setup fixes (take 3)
icside: fix ->speedproc to return on unsupported modes (take 5)
sgiioc4: use ide_tune_dma()
amd74xx/via82cxxx: use ide_tune_dma()
ide: add ide_set{_max}_pio() (take 4)
ide: Kconfig face-lift
ide: move ide_rate_filter() calls to the upper layer (take 2)
sis5513: add ->udma_filter method for chipset_family >= ATA_133
ide: mode limiting fixes for user requested speed changes
ide: add missing ide_rate_filter() calls to ->speedproc()-s
ide: call udma_filter() before resorting to the UltraDMA mask
ide: make jmicron match vendor and device class
pdc202xx_new: switch to using pci_get_slot() (take 2)
...
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Update Cobalt Qube series front LED support
leds: Add Cobalt Raq series LEDs support
leds: Rename leds-cobalt driver
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6
* 'dmi-const' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
drivers/firmware: const-ify DMI API and internals
|
|
* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
[BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
compat_ioctl: move floppy handlers to block/compat_ioctl.c
compat_ioctl: move cdrom handlers to block/compat_ioctl.c
compat_ioctl: move BLKPG handling to block/compat_ioctl.c
compat_ioctl: move hdio calls to block/compat_ioctl.c
compat_ioctl: handle blk_trace ioctls
compat_ioctl: add compat_blkdev_driver_ioctl()
compat_ioctl: move common block ioctls to compat_blkdev_ioctl
Sysace: Don't enable IRQ until after interrupt handler is registered
Sysace: sparse fixes
Sysace: Minor coding convention fixup
drivers/block/umem: use DRIVER_NAME where appropriate
drivers/block/umem: trim trailing whitespace
drivers/block/umem: minor cleanups
drivers/block/umem: use dev_printk()
drivers/block/umem: move private include away from include/linux
Sysace: Labels in C code should not be indented.
Sysace: Add of_platform_bus binding
Sysace: Move IRQ handler registration to occur after FSM is initialized
Sysace: minor rework and cleanup changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (74 commits)
Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
blackfin enable arbitary speed serial setting
Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT and DEBUG_KERNEL_START
Blackfin arch: fix typo in register name
Blackfin arch: trim the Blackfin arch MAINTAINERS list
Blackfin arch: fix bug libstdc++ calling writev with an iovec containing { NULL, 0 } fails on Blackfin
Blackfin arch: Export strcpy - occasionally get module link failures otherwise
Blackfin arch: the load address is not safe to point to as a workaround for ANOMALY 05000281
Blackfin arch: show_mem can not be marked as init, since it is called during OOM condition
Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
Blackfin arch: update kgdb patch
Blackfin arch: Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
Blackfin arch: Print out debug info, as early as possible
Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
Blackfin arch: fix endless loop bug when a double fault happens
Blackfin arch: Initial patch to add earlyprintk support
Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
Blackfin arch: add more common defines for output sections
Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (310 commits)
V4L/DVB (6316): Change list_for_each+list_entry to list_for_each_entry
V4L/DVB (6315): pvrusb2: Change list_for_each+list_entry to list_for_each_entry
V4L/DVB (6314): saa7134: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6313): ivtv: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6312): cx88: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6311): dvb: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6308): V4L: zc0301, remove bad usage of ERESTARTSYS
V4L/DVB (6307): V4L: w9968cf, remove bad usage of ERESTARTSYS
V4L/DVB (6306): Few clenups for saa7134 resume code
V4L/DVB (6305): V4L: videobuf-core.c avoid NULL dereferences in videobuf-core
V4L/DVB (6301): pvrusb: Update DEBUGIFC sysfs to kernel 2.6.13+
V4L/DVB (6300): CodingStyle cleanup
V4L/DVB (6299): dvb: Add dependencies for VIDEOBUF_DVB
V4L/DVB (6297): cx23885: remove wrong Kconfig selection of VIDEOBUF
V4L/DVB (6296): dib0700: add support for AverMedia DVB-T Express card
V4L/DVB (6295): saa7134: add autodetection for KWorld ATSC-115
V4L/DVB (6293): V4L: convert struct class_device to struct device
V4L/DVB (6292): videobuf_core init always require callback implementation
V4L/DVB (6291): Fix: avoid oops on some SMP machines
V4L/DVB (6290): remove videobuf_set_pci_ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (67 commits)
mmc: don't use weight32()
pxamci: support arbitrary block size
sdio: make the IRQ thread more resilient in the presence of bad states
sdio: fix IRQ diagnostic message
sdhci: remove old dma module params
sdhci: add SDHCI_QUIRK_BROKEN_DMA quirk
sdhci: remove DMA capability check from controller's PCI Class reg
sdhci: fix a typo
mmc: Disabler for Ricoh MMC controller
sdio: adaptive interrupt polling
mmc: pxamci: add SDIO card interrupt reporting capability
mmc: pxamci: set proper buswidth capabilities according to PXA flavor
mmc: pxamci: set proper block capabilities according to PXA flavor
mmc: pxamci: better pending IRQ determination
arm: i.MX/MX1 SDHC implements SD cards read-only switch read-back
mmc: add led trigger
mmc_spi host driver
MMC core learns about SPI
MMC/SD card driver learns SPI
MMC headers learn about SPI
...
|
|
Handle the corner case where budget is exhausted correctly.
And save unnecessary read of index register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.
v2:
* Fix pmac_ide_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Return failure in ->speedproc method for unsupported/invalid transfer
modes passed from user-space (fixes theoretical OOPS in ali_tune_pio()
and/or setting random PIO timings on host controller + disabling UDMA
bit + setting unsupported/invalid transfer mode on the device).
* Don't disable UDMA bit when programming PIO modes.
* Add FIXME about DMA timings never being set.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
(->set_pio_mode method) so the controller is always programmed correctly for
PIO transfers (this is important if DMA is not going to be used).
* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There is no need to do it in cs5520_tune_chipset() (->speedproc method)
since it is correctly handled by cs5520_dma_on() (->ide_dma_on method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ide_config_drive_speed() called by sc1200_set_xfer_mode() already gives
a meaningful warning message in case of failure.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add { 0, 0 } entry to {kauai,shasta}_pio_timings[] so kauai_lookup_timing()
always returns a valid PIO timing (fixes PIO timing not being set for devices
with minimum PIO cycle <= 120ns).
* Add setting transfer mode on the device to pmac_ide_set_pio_mode().
* Fix pmac_ide_set_pio() to always program chipset for given PIO timing instead
of only when the device we want to program PIO timing for is the currently
selected one.
* Now that pmac_ide_set_pio() is fixed there is no need to set transfer mode
on the device and program chipset for PIO in pmac_ide_tune_chipset()
(returning 0 == success is not entirely correct but is OK for now since
the upper layers are only checking ->speedproc return value for DMA modes).
v2:
* s/speed/XFER_PIO_0 + pio/ in pmac_ide_set_pio_mode() so it actually compiles.
* Removal of kauai_lookup_timing() return value checking went to separate patch.
v3:
* Use XFER_PIO_0 not XFER_PIO. (Noticed by Ben)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* All other implementations of ->speedproc return zero on success
and non-zero on failure. Currently it doesn't matter for icside host
driver and isn't a bug per se since:
- ide_set_xfer_rate() return value is ignored by all IDE core users
- icside doesn't (yet!) use ide_tune_dma() in icside_dma_check()
but sooner or later we will need to fix anyway - so lets do it now.
* icside_set_speed() happily accepts unsupported transfer modes which
results in drive->drive_data being set to the maximum value (480)
and drive->current_speed being set to the unsupported transfer mode.
Fix it.
v2:
* The initial version of the patch was broken because it didn't take into
the account (the different from usual) return values of icside_set_speed()
(Noticed by Russell).
v3:
* Remove no longer needed initialization/checking of cycle_time
(Noticed by Sergei).
* No need to set drive->drive_data if DMA is not going to be used
(Noticed by Sergei).
* Remove incorrect setting of drive->current_speed
(Noticed by Sergei).
* Move ide_config_drive_speed() at the end of icside_set_speed().
v4:
* If DMA mode is not found in icside_dma_check() then just return "-1" and
don't call icside_set_speed() (v3 got it wrong and "1" was returned instead).
v5:
* Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return
value (just like it was before this patch).
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add DRV_NAME define and use it instead of sgiioc4_chipset.name.
* Remove no longer needed sgiioc4_chipset.
* Remove needless clearing of ->atapi_dma from ide_dma_sgiioc4().
* Fix ide_dma_sgiioc4() to return success/failure. Check return value in
sgiioc4_ide_setup_pci_device() and set hwif->autodma accordingly. Also add
missing setting of drive->autodma.
* Add sgiioc4_speedproc() (implementation of ->speedproc method).
* Fix ->mwdma_mask (MWDMA2 mask is 0x04 not 0x02) and remove incorrect
->swdma_mask. Also remove needless initialization of ->ultra_mask.
* Use ide_tune_dma() in sgiioc4_ide_dma_check(), this fixes following bugs:
- DMA capability bit not being checked on the device
- DMA blacklist not being checked
- MWDMA2 mode support by device not being checked
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs:
- DMA capability bit not being checked on the device
- DMA blacklist not being checked
- DMA mode being programmed even if drive->autodma == 0
(thus possibly destroying PIO timings)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Convert config options for PCI host drivers to select BLK_DEV_IDEPCI.
* Same for BLK_DEV_IDEDMA_PCI and PCI DMA host drivers, also make this
config option select BLK_DEV_IDEPCI.
* Remove no longer needed help for BLK_DEV_IDEPCI and BLK_DEV_IDEDMA_PCI.
* Remove redundant IDE_CHIPSETS config option.
As a result of this patch users have now three less config options
to worry about and can just select host drivers that they need
(IDE config menu is "flatter").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add sis5513_ata133_udma_filter() for chipset_family >= ATA_133,
use it to filter UDMA6 mode if ATA133 bit is disabled.
* Remove no longer needed UDMA6 limiting logic from sis5513_tune_chipset().
* Bump driver version.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add an extra argument to ide_max_dma_mode() for passing requested transfer
mode. Use it as an upper limit when finding the best DMA for device/host.
* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
ide_find_dma_mode(). Also add inline ide_find_dma_mode() version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
to avoid false warning from eighty_ninty_three().
* Use ide_find_dma_mode() to limit the user requested transfer mode in
ide_rate_filter(). Also limit the requested mode by host max PIO mode.
Above changes make ide_rate_filter() to:
* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
and 0x25-0x39, values > 0x46 were already clipped down, same for values
0x25-0x39 but iff UDMA was not supported by the host).
* Clip desired transfer mode down if it is currently unsupported by IDE core
(PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
not supported by the host).
* Clip desired transfer mode down according to the host capabilities
(UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
also ->atapi_dma flag was not respected).
* Clip desired transfer mode down according to the device capabilities
(except PIO modes for now which require mode work) - shouldn't be a
problem since ide_set_xfer_rate() is called _after_ device has accepted
given transfer mode.
and also result in a number of host driver specific bugfixes:
* icside
- clip unsupported PIO5 mode down
- fix unsupported/invalid modes being set in drive->current_speed
* ide-cris
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix BUG() on unsupported/invalid modes
* au1xxx-ide
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
(if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down
* aec62xx
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix 0x00 being programmed as PIO timing for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* alim15x3
- clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
- fix theoretical OOPS for 0x0F mode
- fix unsupported/invalid modes being set on the device
* amd74xx
- clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* atiixp
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix cached MWDMA mode being cleared for unsupported/invalid modes
- fix PIO{0,2} timings being programmed for unsupported/invalid modes
- fix theoretical OOPS for PIO5-6 and 0x0F modes
- fix unsupported/invalid modes being set on the device
* cmd64x
- clip unsupported SWDMA0-2 modes down
* cs5530
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* cs5535
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix theoretical OOPS for PIO5-6 and 0x0F modes
* hpt34x
- clip DMA modes down for ATAPI devices
- fix invalid timings being programmed for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* hpt366
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for unsupported/invalid modes
- fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* it8213
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* it821x
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
(chipset in smart mode and revision 0x10 in pass-through mode)
* jmicron
- clip unsupported SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_new
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_old
- clip unsupported PIO5 mode down
- fix incorrect timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* piix
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* sc1200
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* scc_pata
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down
* serverworks
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* siimage
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices (SATA chipsets)
* sis5513
- clip unsupported PIO5 mode down
- fix BUG() on unsupported/invalid modes
* sl82c105
- clip unsupported SWDMA0-2 modes down
* slc90e66
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* tc86c001
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
- fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* triflex
- clip unsupported PIO5 mode down
* via82cxxx
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* pmac
- clip unsupported PIO5 and SWDMA0-2 modes down
* cmd640/ht6560b
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)
* opti621
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)
While at it:
* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().
* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
to use ide_rate_filter().
This results in the following modes (from user requests) being clipped down:
- invalid modes (values 0x46-0xFF) [ for all hosts ]
- unsupported by a host UDMA modes [ for hosts which support UDMA]
- all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
- invalid modes (values 0x25-0x39) [ for hosts which don't support UDMA ]
* Host driver specific changes in behavior:
icside:
- no change
cris-ide
- clip unsupported UDMA3-6 modes down
- fix BUG() on trying to set unsupported UDMA3-6 modes
au1xxx-ide/pmac
- clip unsupported UDMA modes down
amd74xx/via82cxxx
- clip unsupported UDMA modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* While at it remove no longer needed checks from pmac.c driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Give the udma_filter() method call precedence over using the mode masks.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible. Matching
vendor and device class is enough.
For backward compatibility, jmicron still needs to match 361,3,5,6,8
DIDs regardless of device class if libata is not configured but won't
need further DID update from this point.
Bart: cosmetic fixes to jmicron_chipset
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Switch to using pci_get_slot() in init_setup_pdc20270() to get to the mate chip
behind DC21150 bridge as there's no need for the driver itself to walk the list
of the PCI devices (and the driver didn't check the bus # of the found device).
While at it, make it emit warning about IRQ # being fixed up (just like hpt366.c
does) and "beautify" this whole function as well as init_setup_pdc20276()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ACPI spec defines the sequence of IDE power on/off:
Powering down:
Call _GTM.
Power down drive (calls _PS3 method and turns off power planes).
Powering up:
Power up drive (calls _PS0 method if present and turns on power planes).
Call _STM passing info from _GTM (possibly modified), with ID data from
each drive.
Initialize the channel.
May modify the results of _GTF.
For each drive:
Call _GTF.
Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This is now very similar to pata_platform.c, they both use
same platform data structure and same resources.
To achieve that, byte_lanes_swapping platform data variable
and platform specified iops removed from that driver. It's fine,
since those were never used anyway.
pata_platform and ide_platform are carrying same driver names,
to easily switch between these drivers, without need to touch
platform code.
Bart:
- build fix from Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:
- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
with his consent;
- install the method for all chips to only return empty mask if a SATA drive
is detected on HPT372{AN]/374 chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
SB700 supports one physical IDE channel, but SB700 SATA controller
supports combined mode. When the SATA combined mode is enabled,
two SATA ports (port4 and port5) share one IDE channel from IDE
controller, and PATA will share the other IDE channel.
Our previous patch adding SB700 IDE device ID only supports one
IDE channel, which contains bug. The attached patch fixes the bug.
Signed-off-by: "Shane Huang" <Shane.Huang@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
|
This patch adds support for powering on and off the Samsung LTV350QV LCD
panel via SPI. The driver responds to framebuffer power management, it
powers off the panel on reboot/halt/poweroff. It can also be controlled
through sysfs. The panel is powered up when the module is loaded, and off
when the module is unloaded. Verified on AVR32 STK1000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
