aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-03-10ipw2200: use kmalloc for large local variablesZhu Yi
Fixed below compiler warning: drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’: drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of 1168 bytes is larger than 1024 bytes Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10ath5k: read eeprom IQ calibration values correctly for G modeBruno Randolf
we read the IQ correction values (i_cal and q_cal) for G mode from a wrong location (the same shifts as for A mode is applied which is incorrect). use correct locations, matching the docs and HAL sources. also we should write IQ correction only when we have that information in the EEPROM, starting from version 4. also write it in the same way as we do in the periodic recalibration (enable last), just to be sure. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10ath5k: fix I/Q calibration (for real)Bruno Randolf
I/Q calibration was completely broken, resulting in a high number of CRC errors on received packets. before i could see around 10% to 20% CRC errors, with this patch they are between 0% and 3%. 1.) the removal of the mask in commit "ath5k: Fix I/Q calibration (f1cf2dbd0f798b71b1590e7aca6647f2caef1649)" resulted in no mask beeing used when writing the I/Q values into the register. additional errors in the calculation of the values (see 2.) resulted too high numbers, exceeding the masks, so wrong values like 0xfffffffe were written. to be safe we should always use the bitmask when writing parts of a register. 2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we convert to a signed value later by substracting 128. this resulted in too low numbers for Q many times, which were limited to -16 by the boundary check later on. 3.) checked everything against the HAL sources and took over comments and minor optimizations from there. 4.) we can't use ENABLE_BITS when we want to write a number (the number can contain zeros). also always write the correction values first and set ENABLE bit last, like the HAL does. Signed-off-by: Bruno Randolf <br1@einfach.org> Cc: stable@kernel.org Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10ath5k: fix TSF resetBruno Randolf
to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a function for that so use it. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10ath5k: use fixed antenna for tx descriptorsBruno Randolf
when using a fixed antenna we should use the antenna number in all tx descriptors, otherwise the hardware will sometimes send the frame out on the other antenna. it seems like the hardware does not always respect the default antenna and diversity settings (esp. AR5K_STA_ID1_DEFAULT_ANTENNA). also i would like to note that antenna diversity does not always work correctly on 5414 (at least) when only one antenna is connected: for example all frames might be received on antenna A but still the HW tries to send on antenna B some times, causing packet loss. this is both verified with the antenna statistics output of the previous patch and a spectrum analyzer. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10libipw: split ieee->networks into small piecesZhu Yi
The ieee->networks consists of 128 struct libipw_network entries. If we allocate this chunk of memory altogether, it ends up with an order 4 page allocation. High order page allocation is likely to fail on system high load. This patch splits the big chunk memory allocation into small pieces, each is 344 bytes, allocates them with 128 times. The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989 Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-10rt2x00: remove KSEG1ADDR define from rt2x00soc.hHelmut Schaa
Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver oopses on the target platform (Ralink rt3050 board). Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-08can: fix bfin_can build error after alloc_candev() changeBarry Song
Looks like commit a6e4bc530403 didn't include updates to drivers so the Blackfin CAN driver fails to build now. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: remove extra space from board namesAmit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: fix bios version checkAmit Kumar Salecha
Bios sub version from unified fw image is calculated incorrect. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: validate unified fw imageSucheta Chakraborty
Validate all sections of unified fw image, before accessing them, to avoid seg fault. Signed-off-by: Sucheta Chakraborty <sucheta@dut6195.unminc.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: fix multicast handlingSucheta Chakraborty
For promiscuous mode, driver send request to device for deleting multicast addresses and again it send request for adding them back while exiting from this mode, this is bad for performance. Just setting device in promiscuous mode is enough, no need to del/add multicast addresses. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: additional driver statistics.Sucheta Chakraborty
Statistics added for lro/lso bytes, count for tx stop queue and wake queue and skb alloc failure count. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08qlcnic: fix tx csum statusSucheta Chakraborty
Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account to show tx csum status, which driver doesn't set while disabling tx csum. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08be2net: remove unused code in be_load_fwAjit Khaparde
This patch cleans up some unused code from be_load_fw(). Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-08be2net: remove usage of be_pci_funcAjit Khaparde
When PCI functions are virtuialized in applications by assigning PCI functions to VM (PCI passthrough), the be2net driver in the VM sees a different function number. So, use of PCI function number in any calculation will break existing code. This patch takes care of it. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07cpmac: bump version to 0.5.2Florian Fainelli
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07cpmac: fallback to switch mode if no PHY chip foundFlorian Fainelli
If we were unable to detect a PHY on any of the MDIO bus id we tried instead of bailing out with -ENODEV, assume the MAC is connected to a switch and use MDIO bus 0. This unbreaks quite a lot of devices out there whose switch cannot be detected. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07cpmac: fix the receiving of 802.1q framesFlorian Fainelli
Despite what the comment above CPMAC_SKB_SIZE says, the hardware also needs to account for the FCS length in a received frame. This patch fix the receiving of 802.1q frames which have 4 more bytes. While at it unhardcode the definition and use the one from if_vlan.h. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07another pegasus usb net devicePetko Manolov
This one removes trailing whitespace in pegasus.h and more importantly adds new Pegasus compatible device. Signed-off-by: Julian Brown <julian@codesourcery.com> Signed-off-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07irda-usb: add error handling and fix leakDan Carpenter
If the call to kcalloc() fails then we should return -ENOMEM. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07ems_usb: cleanup: remove uneeded checkDan Carpenter
"skb" is alway non-null here, but even if it were null the check isn't needed because dev_kfree_skb() can handle it. This eliminates a smatch warning about dereferencing a variable before checking that it is non-null. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-07fix a race in ks8695_pollFigo.zhang
fix a race at the end of NAPI processing in ks8695_poll() function. Signed-off-by:Figo.zhang <figo1802@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-05s2io: Fixing debug messageBreno Leitao
Currently s2io is dumping debug messages using the interface name before it was allocated, showing a message like the following: s2io: eth%d: Ring Mem PHY: 0x7ef80000 s2io: s2io_reset: Resetting XFrame card eth%d This patch just fixes it, printing the pci bus information for the card instead of the interface name. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-05e1000e: fix packet corruption and tx hang during NFSv2Jesse Brandeburg
when receiving a particular type of NFS v2 UDP traffic, the hardware could DMA some bad data and then hang, possibly corrupting memory. Disable the NFS parsing in this hardware, verified to fix the bug. Originally reported and reproduced by RedHat's Neil Horman CC: nhorman@tuxdriver.com Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-05typhoon: fix incorrect use of smp_wmb()David Dillow
The typhoon driver was incorrectly using smp_wmb() to order memory accesses against IO to the NIC in a few instances. Use wmb() instead, which is required to actually order between memory types. Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-05net: smc91x: Support Qualcomm MSM development boards.David Brown
Signed-off-by: David Brown <davidb@quicinc.com> Signed-off-by: Daniel Walker <dwalker@codeaurora.org> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-04rndis_wlan: correct multicast_list handling V3Jiri Pirko
My previous patch (655ffee284dfcf9a24ac0343f3e5ee6db85b85c5) added locking in a bad way. Because rndis_set_oid can sleep, there is need to prepare multicast addresses into local buffer under netif_addr_lock first, then call rndis_set_oid outside. This caused reorganizing of the whole function. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-04cxgb3: fix hot plug removal crashDivy Le Ray
queue restart tasklets need to be stopped after napi handlers are stopped since the latter can restart them. So stop them after stopping napi. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-04gianfar: Fix TX ring processing on SMP machinesAnton Vorontsov
Starting with commit a3bc1f11e9b867a4f49505 ("gianfar: Revive SKB recycling") gianfar driver sooner or later stops transmitting any packets on SMP machines. start_xmit() prepares new skb for transmitting, generally it does three things: 1. sets up all BDs (marks them ready to send), except the first one. 2. stores skb into tx_queue->tx_skbuff so that clean_tx_ring() would cleanup it later. 3. sets up the first BD, i.e. marks it ready. Here is what clean_tx_ring() does: 1. reads skbs from tx_queue->tx_skbuff 2. checks if the *last* BD is ready. If it's still ready [to send] then it it isn't transmitted, so clean_tx_ring() returns. Otherwise it actually cleanups BDs. All is OK. Now, if there is just one BD, code flow: - start_xmit(): stores skb into tx_skbuff. Note that the first BD (which is also the last one) isn't marked as ready, yet. - clean_tx_ring(): sees that skb is not null, *and* its lstatus says that it is NOT ready (like if BD was sent), so it cleans it up (bad!) - start_xmit(): marks BD as ready [to send], but it's too late. We can fix this simply by reordering lstatus/tx_skbuff writes. Reported-by: Martyn Welch <martyn.welch@ge.com> Bisected-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com> Tested-by: Martyn Welch <martyn.welch@ge.com> Cc: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Cc: Stable <stable@vger.kernel.org> [2.6.33] Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-04r8169: use correct barrier between cacheable and non-cacheable memoryDavid Dillow
r8169 needs certain writes to be visible to other CPUs or the NIC before touching the hardware, but was using smp_wmb() which is only required to order cacheable memory access. Switch to wmb() which is required to order both cacheable and non-cacheable memory. Noticed by Catalin Marinas and Paul Mackerras. Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-03Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-03-03rt2x00: Export rt2x00soc_probe from rt2x00socHelmut Schaa
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci. Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol rt2x00soc_probe". Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-03mac80211: Fix HT rate control configurationSujith
Handling HT configuration changes involved setting the channel with the new HT parameters and then issuing a rate_update() notification to the driver. This behavior changed after the off-channel changes. Now, the channel is not updated with the new HT params in enable_ht() - instead, it is now done when the scan work terminates. This results in the driver depending on stale information, defaulting to non-HT mode always. Fix this by passing the new channel type to the driver. Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-03davinci_emac: off by oneDan Carpenter
This off by one error was found by smatch. drivers/net/davinci_emac.c +2390 emac_dev_open(13) error: buffer overflow 'priv->mac_addr' 6 <= 6 Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-03cassini: fix off by oneDan Carpenter
There are only 6 link_modes. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-03be2net: download NCSI section during firmware updateSarveshwar Bandi
Adding code to update NCSI section while updating firmware on the controller. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-03cpmac: use after freeDan Carpenter
The original code dereferenced "cpmac_mii" after calling "mdiobus_free(cpmac_mii);" Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-02iwlwifi: load firmware asynchronously before mac80211 registrationJohannes Berg
At the wireless summit in Portland we discussed a way of loading firmware asynchronously from ->probe() before registration to mac80211, in order to register with the wireless subsystems with complete information in cases where firmware is required to know parameters. This is not yet the case in iwlwifi, but for some new features we're working on it will be the case since those will only be supported by new firmware images. Hence, to start with, convert iwlwifi to load firmware asynchronously from probe, unbinding the device when firmware loading fails, and only registering with the wireless subsystems after firmware has been loaded successfully. Future patches will hook into this to register the new firmware capabilities, depending on the firmware API version. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02ar9170: load firmware asynchronouslyJohannes Berg
This converts ar9170 to load firmware asynchronously out of ->probe() and only register with mac80211 when all firmware has been loaded successfully. If, on the other hand, any firmware fails to load, it will now unbind from the device. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02rt2x00: fix rt2800pci compilation with SoCHelmut Schaa
Compiling rt2800pci with CONFIG_RT2800PCI_SOC fails with "... rt2880pci.c: error: incompatible type for argument 2 of 'rt2x00soc_probe'". Fix this by using &rt2800pci_ops instead of rt2800pci_ops. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02rt2x00: Add USB ID for CEIVA adapter to rt73usbBryan Polk
This adds support for CEIVA USB wireless adapters to the rt73usb driver. Signed-off-by: Bryan Polk <sainth@eidolons.org> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02ath9k: fix lockdep warning when unloading moduleMing Lei
Since txq->axq_lock may be hold in softirq context, it must be acquired with spin_lock_bh() instead of spin_lock() if softieq is enabled. The patch fixes the lockdep warning below when unloading ath9k modules. ================================= [ INFO: inconsistent lock state ] 2.6.33-wl #12 --------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. rmmod/3642 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&txq->axq_lock)->rlock){+.?...}, at: [<ffffffffa03568c3>] ath_tx_node_cleanup+0x62/0x180 [ath9k] {IN-SOFTIRQ-W} state was registered at: [<ffffffff8107577d>] __lock_acquire+0x2f6/0xd35 [<ffffffff81076289>] lock_acquire+0xcd/0xf1 [<ffffffff813a7486>] _raw_spin_lock_bh+0x3b/0x6e [<ffffffffa0356b49>] spin_lock_bh+0xe/0x10 [ath9k] [<ffffffffa0358ec7>] ath_tx_tasklet+0xcd/0x391 [ath9k] [<ffffffffa0354f5f>] ath9k_tasklet+0x70/0xc8 [ath9k] [<ffffffff8104e601>] tasklet_action+0x8c/0xf4 [<ffffffff8104f459>] __do_softirq+0xf8/0x1cd [<ffffffff8100ab1c>] call_softirq+0x1c/0x30 [<ffffffff8100c2cf>] do_softirq+0x4b/0xa3 [<ffffffff8104f045>] irq_exit+0x4a/0x8c [<ffffffff813acccc>] do_IRQ+0xac/0xc3 [<ffffffff813a7d53>] ret_from_intr+0x0/0x16 [<ffffffff81302d52>] cpuidle_idle_call+0x9e/0xf8 [<ffffffff81008be7>] cpu_idle+0x62/0x9d [<ffffffff81391c1a>] rest_init+0x7e/0x80 [<ffffffff818bbd38>] start_kernel+0x3e8/0x3f3 [<ffffffff818bb2bc>] x86_64_start_reservations+0xa7/0xab [<ffffffff818bb3b8>] x86_64_start_kernel+0xf8/0x107 irq event stamp: 42037 hardirqs last enabled at (42037): [<ffffffff813a7b21>] _raw_spin_unlock_irqrestore+0x47/0x56 hardirqs last disabled at (42036): [<ffffffff813a72f4>] _raw_spin_lock_irqsave+0x2b/0x88 softirqs last enabled at (42000): [<ffffffffa0353ea6>] spin_unlock_bh+0xe/0x10 [ath9k] softirqs last disabled at (41998): [<ffffffff813a7463>] _raw_spin_lock_bh+0x18/0x6e other info that might help us debug this: 4 locks held by rmmod/3642: #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff8132c10d>] rtnl_lock+0x17/0x19 #1: (&wdev->mtx){+.+.+.}, at: [<ffffffffa01e53f2>] cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211] #2: (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0260834>] ieee80211_mgd_deauth+0x3f/0x17e [mac80211] #3: (&local->sta_mtx){+.+.+.}, at: [<ffffffffa025a381>] sta_info_destroy_addr+0x2b/0x5e [mac80211] stack backtrace: Pid: 3642, comm: rmmod Not tainted 2.6.33-wl #12 Call Trace: [<ffffffff81074469>] valid_state+0x178/0x18b [<ffffffff81014f94>] ? save_stack_trace+0x2f/0x4c [<ffffffff81074e08>] ? check_usage_backwards+0x0/0x88 [<ffffffff8107458f>] mark_lock+0x113/0x230 [<ffffffff810757f1>] __lock_acquire+0x36a/0xd35 [<ffffffff8101018d>] ? native_sched_clock+0x2d/0x5f [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k] [<ffffffff81076289>] lock_acquire+0xcd/0xf1 [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k] [<ffffffff810732eb>] ? trace_hardirqs_off+0xd/0xf [<ffffffff813a7193>] _raw_spin_lock+0x36/0x69 [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k] [<ffffffffa03568c3>] ath_tx_node_cleanup+0x62/0x180 [ath9k] [<ffffffff810749ed>] ? trace_hardirqs_on+0xd/0xf [<ffffffffa0353950>] ath9k_sta_remove+0x22/0x26 [ath9k] [<ffffffffa025a08f>] __sta_info_destroy+0x1ad/0x38c [mac80211] [<ffffffffa025a394>] sta_info_destroy_addr+0x3e/0x5e [mac80211] [<ffffffffa02605d6>] ieee80211_set_disassoc+0x175/0x180 [mac80211] [<ffffffffa026084d>] ieee80211_mgd_deauth+0x58/0x17e [mac80211] [<ffffffff813a60c1>] ? __mutex_lock_common+0x37f/0x3a4 [<ffffffffa01e53f2>] ? cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211] [<ffffffffa026786e>] ieee80211_deauth+0x1e/0x20 [mac80211] [<ffffffffa01f47f9>] __cfg80211_mlme_deauth+0x130/0x13f [cfg80211] [<ffffffffa01e53f2>] ? cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211] [<ffffffff810732eb>] ? trace_hardirqs_off+0xd/0xf [<ffffffffa01f7eee>] __cfg80211_disconnect+0x111/0x189 [cfg80211] [<ffffffffa01e5433>] cfg80211_netdev_notifier_call+0x2ce/0x46d [cfg80211] [<ffffffff813aa9ea>] notifier_call_chain+0x37/0x63 [<ffffffff81068c98>] raw_notifier_call_chain+0x14/0x16 [<ffffffff81322e97>] call_netdevice_notifiers+0x1b/0x1d [<ffffffff8132386d>] dev_close+0x6a/0xa6 [<ffffffff8132395f>] rollback_registered_many+0xb6/0x2f4 [<ffffffff81323bb8>] unregister_netdevice_many+0x1b/0x66 [<ffffffffa026494f>] ieee80211_remove_interfaces+0xc5/0xd0 [mac80211] [<ffffffffa02580a2>] ieee80211_unregister_hw+0x47/0xe8 [mac80211] [<ffffffffa035290e>] ath9k_deinit_device+0x7a/0x9b [ath9k] [<ffffffffa035bc26>] ath_pci_remove+0x38/0x76 [ath9k] [<ffffffff8120940a>] pci_device_remove+0x2d/0x51 [<ffffffff8129d797>] __device_release_driver+0x7b/0xd1 [<ffffffff8129d885>] driver_detach+0x98/0xbe [<ffffffff8129ca7a>] bus_remove_driver+0x94/0xb7 [<ffffffff8129ddd6>] driver_unregister+0x6c/0x74 [<ffffffff812096d2>] pci_unregister_driver+0x46/0xad [<ffffffffa035bae1>] ath_pci_exit+0x15/0x17 [ath9k] [<ffffffffa035e1a2>] ath9k_exit+0xe/0x2f [ath9k] [<ffffffff8108050a>] sys_delete_module+0x1c7/0x236 [<ffffffff813a7df5>] ? retint_swapgs+0x13/0x1b [<ffffffff810749b5>] ? trace_hardirqs_on_caller+0x119/0x144 [<ffffffff8109b9f6>] ? audit_syscall_entry+0x11e/0x14a [<ffffffff81009bb2>] system_call_fastpath+0x16/0x1b wlan1: deauthenticating from 00:23:cd:e1:f9:b2 by local choice (reason=3) PM: Removing info for No Bus:wlan1 cfg80211: Calling CRDA to update world regulatory domain PM: Removing info for No Bus:rfkill2 PM: Removing info for No Bus:phy1 ath9k 0000:16:00.0: PCI INT A disabled Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02zd1211rw: fix potential array underflowDan Carpenter
The first chunk fixes a debugging assert to print a warning about array underflows. The second chunk corrects a potential array underflow. I also removed an assert in the second chunk because it can no longer happen. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02airo: return from set_wep_key() when key length is zeroStanislaw Gruszka
Even if keylen == 0 is a bug and should not really happen, better avoid possibility of passing bad value to firmware. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-02Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linuxLinus Torvalds
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (49 commits) OMAP: DSS2: Taal: Fix TE when resuming OMAP: DSS2: Taal: Fix ESD check OMAP: DSS2: OMAPFB: Constify some function parameters OMAP: DSS2: OMAPFB: install omapfb.h OMAP: DSS2: DSI: add error prints OMAP: DSS2: TPO-TD03MTEA1: fix function names OMAP: DSS2: DSI: add dsi_vc_dcs_read_2() helper OMAP: DSS2: OMAPFB: Remove FB_OMAP2_FORCE_AUTO_UPDATE OMAP: DSS2: DSI: remove external TE support OMAP: DSS2: move timing functions OMAP: DSS2: move set/get_wss() OMAP: DSS2: move enable/disable/suspend/resume OMAP: DSS2: move update() and sync() OMAP: DSS2: move set/get_update_mode() OMAP: DSS2: move enable/get_te() OMAP: DSS2: move get_recommended_bpp() OMAP: DSS2: move get_resolution() OMAP: DSS2: move enable/disable_channel to overlay manager OMAP: DSS2: move wait_vsync() OMAP: DSS2: move get/set_rotate() ...
2010-03-02Merge branch 'omap-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits) omap2: Initialize Menelaus and MMC for N8X0 AM3517 EVM: correct typo - tca6416 mispelt as tca6516 AM3517 EVM: Enable I2C support AM35x: Enable OMAP_MUX in defconfig AM35x: Add missing GPIO mux config for EHCI port Zoom3: Defconfig update omap: i2c: Fix muxing for command line enabled bus OMAP4: clock: Remove clock hacks from timer-gp.c OMAP4: clock: Add dummy clock nodes for interface clocks OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck OMAP2+ clock: revise omap2_clk_{disable,enable}() OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code OMAP clockdomain: if no autodeps exist, don't try to add or remove them OMAP hwmod: add hwmod class support OMAP hwmod: convert header files with static allocations into C files OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630 OMAP4 clock: drop the ALWAYS_ENABLED clock flag OMAP clock: drop RATE_FIXED clock flag ...
2010-03-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: sparc: Support show_unhandled_signals. sparc: use __ratelimit sunxvr500: Additional PCI id for sunxvr500 driver sparc: use asm-generic/scatterlist.h sparc64: If 'slot-names' property exist, create sysfs PCI slot information. sparc: remove trailing space in messages sparc: remove redundant return statements
2010-03-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits) virtio_net: remove forgotten assignment be2net: fix tx completion polling sis190: fix cable detect via link status poll net: fix protocol sk_buff field bridge: Fix build error when IGMP_SNOOPING is not enabled bnx2x: Tx barriers and locks scm: Only support SCM_RIGHTS on unix domain sockets. vhost-net: restart tx poll on sk_sndbuf full vhost: fix get_user_pages_fast error handling vhost: initialize log eventfd context pointer vhost: logging thinko fix wireless: convert to use netdev_for_each_mc_addr ethtool: do not set some flags, if others failed ipoib: returned back addrlen check for mc addresses netlink: Adding inode field to /proc/net/netlink axnet_cs: add new id bridge: Make IGMP snooping depend upon BRIDGE. bridge: Add multicast count/interval sysfs entries bridge: Add hash elasticity/max sysfs entries bridge: Add multicast_snooping sysfs toggle ... Trivial conflicts in Documentation/feature-removal-schedule.txt
2010-03-02OMAP: DSS2: Taal: Fix TE when resumingTomi Valkeinen
TE was not initialized properly on power on, which broke TE when resuming from suspend. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>