| Age | Commit message (Collapse) | Author |
|---|
|
This fixes up the simplified multi-evt handling when sparseirq support is
enabled. While vectors are redirected through the single unique masking
source, each one of the redirected vectors still requires its own backing
irq_desc, which needs to be manually allocated in the sparseirq case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
In certain configurations linux/err.h is not included through alternate
means, resulting in:
drivers/usb/gadget/m66592-udc.c:1646: error: implicit declaration of function 'IS_ERR'
drivers/usb/gadget/m66592-udc.c:1649: error: implicit declaration of function 'PTR_ERR'
distcc[15083] ERROR: compile drivers/usb/gadget/m66592-udc.c on localhost failed
make[3]: *** [drivers/usb/gadget/m66592-udc.o] Error 1
make[2]: *** [drivers/usb/gadget] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2
Caught with an ARM config in -next.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch changes the way in which "multi-evt" interrups are handled.
The intc_evt2irq_table and related intc_evt2irq() have been removed and
the "redirecting" handler is installed for the coupled interrupts.
Thanks to that the do_IRQ() function don't have to use another level
of indirection for all the interrupts...
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
This patch modifies the uio_pdrv_genirq driver to support
Runtime PM. The power management implementation simply
runtime resumes the device at open() time and runtime
suspends it at release() time. The user space driver is
responsible for re-initializing the hardware after open().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch modifies the SuperH Mobile CEU driver to support
Runtime PM. Driver callbacks for Runtime PM are empty because
the device registers are always re-initialized after
pm_runtime_get_sync(). The Runtime PM functions replaces the
clock framework module stop bit handling in this driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch modifies the SuperH Mobile LCDC framebuffer driver
to support Runtime PM. The driver is using the functions
- pm_runtime_get_sync()
- pm_runtime_put_sync()
to inform the bus code if the hardware is idle or not. If the
hardware is idle then the bus code may call the runtime dev_pm_ops
callbacks to save and restore state. pm_runtime_resume() is used
to allow the driver to access the hardware from probe().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
This patch adds default Runtime PM callbacks to the dev_pm_ops
belonging to the platform bus. The callbacks are weak symbols
that architecture specific code can override.
Allows Runtime PM even though CONFIG_PM_SLEEP=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Introduce a core framework for run-time power management of I/O
devices. Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'. Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level. Document all these things.
Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: check saved state before restore
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt2sas: fix config request and diag reset deadlock
[SCSI] mpt2sas: Bump driver version 01.100.04.00
[SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
[SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
[SCSI] mpt2sas: fix infinite loop inside config request
[SCSI] mpt2sas: Excessive log info causes sas iounit page time out
[SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
[SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
[SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: add GET_PARAM/INFO support for Z pipes
drm/radeon/kms: add r100/r200 OQ support.
drm: Fix sysfs device confusion.
drm/radeon/kms: implement the bo busy ioctl properly.
|
|
Needed for occlusion queries on rv530 chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds the relocation necessary for OQ support on the r100/r200
chipsets.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.
Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
fix the problem that MSC Tests of USBCV detects some warnings.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: I2C STU300 stability updates
i2c-omap: Enable workaround for Errata 1.153 based on
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
i2c-omap: Fix I2C status ACK
|
|
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
|
|
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
There were a few stray unused variables left over, kill them off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
- simplifies irq set freq
- ioctl() was duplicating functionalities of rtc-dev core
- corrected initialization sequence
- use platform_driver_probe
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Angelo Castello <angelo.castello@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
- removed spinlock protection, it's handled by the rtc class
- use platform_driver_probe
- return appropriate code for rtc_read_time
- style issues
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch improves the disable_controller() function in the
r8a66597-udc driver to disable all interrupts and also clear
status flags. With this patch in place the driver survives
kexec.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch updates the r8a66597-udc buffer management code.
Use fixed buffers for bulk and isochronous pipes, also make
sure to handle the isochronous-as-bulk case. With fixed buffers
there is no need to keep track of used buffers with bi_bufnum.
Also, this fixes a potential buffer offset problem where the
base offset incorrectly varies with the number of pipes used.
The m66592 driver recently got fixed in a similar way.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add support for the clock framework to the r8a66597 gadget driver.
This is needed to control the clock driving the USB block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
While in-tree support for the R8A66597 host side has been supported for
some time, the peripheral side has so far been unsupported. This adds a
new USB gadget driver which bridges the gap and finally wires up the
peripheral side as well.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: teardown crtc correctly when fb is destroyed.
drm/kms/radeon: cleanup combios TV table like DDX.
drm/radeon/kms: memset the allocated framebuffer before using it.
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
drm/radeon/kms: implement bo busy check + current domain
drm/radeon/kms: cut down indirects in register accesses.
drm/radeon/kms: Fix up vertical blank interrupt support.
drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
drm/edid: fixup detailed timings like the X server.
drm/radeon/kms: Add specific rs690 authorized register table
|
|
If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
net: restore gnet_stats_basic to previous definition
NETROM: Fix use of static buffer
e1000e: fix use of pci_enable_pcie_error_reporting
e1000e: WoL does not work on 82577/82578 with manageability enabled
cnic: Fix locking in init/exit calls.
cnic: Fix locking in start/stop calls.
bnx2: Use mutex on slow path cnic calls.
cnic: Refine registration with bnx2.
cnic: Fix symbol_put_addr() panic on ia64.
gre: Fix MTU calculation for bound GRE tunnels
pegasus: Add new device ID.
drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
rt2x00: fix memory corruption in rf cache, add a sanity check
ixgbe: Fix receive on real device when VLANs are configured
ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
netxen: free napi resources during detach
netxen: remove netxen workqueue
ixgbe: fix issues setting rx-usecs with legacy interrupts
can: fix oops caused by wrong rtnl newlink usage
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: sh7724 ddr self-refresh changes
sh: use in-soc KEYSC on se7724
sh: CMT suspend/resume
sh: skip disabled LCDC channels
|
|
* 'for-linus' of git://neil.brown.name/md:
Fix new incorrect error return from do_md_stop.
|
|
Recent commit c8c00a6915a2e3d10416e8bdd3138429beb96210
changed the exit paths in do_md_stop and was not quite
careful enough. There is one path were 'err' now needs
to be cleared but it isn't.
So setting an array to readonly (with mdadm --readonly) will
work, but will incorrectly report and error: ENXIO.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (37 commits)
ARM: 5673/1: U300 fix initsection compile warning
ARM: Fix broken highmem support
mx31moboard: invert sdhc ro signal sense
ARM: S3C24XX: Fix clkout mpx error
ARM: S3C64XX: serial: Fix a typo in Kconfig
IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes
OMAP3: RX51: Updated rx51_defconfig
OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up
OMAP3: RX51: Define TWL4030 USB transceiver in board file
OMAP3: Overo: Fix smsc911x platform device resource value
OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size
OMAP2/3: DMA errata correction
OMAP: Fix testing of cpu defines for mach-omap1
OMAP3: Overo: add missing pen-down GPIO definition
OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask
OMAP3: PM: Fix wrong sequence in suspend.
OMAP: PM: CPUfreq: obey min/max settings of policy
OMAP2/3/4: UART: allow in-order port traversal
OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports
OMAP3: Fixed crash bug with serial + suspend
...
|
