aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-07-08cxgb3: Fix mss table initializationDivy Le Ray
Fix the HW SMT table initialization to avoid random mss miscomputations for offload connections. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08cxgb3: use request_firmware() for the EDC registers setupDivy Le Ray
use request_firmware() to load the phy's EDC programmation Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08cxgb3: AEL2020 phy support updateDivy Le Ray
We don't always see the link status update interrupt when we come out of reset and the peer is up. Check and report the link status right before enabling interrupts. Also fix LED settings, to get a consistent link status. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08cxgb3: Fix T3C MAC max packet size accessDivy Le Ray
Max packet size is not the only field in T3C's High Water Mark register. Mask the register to access this field. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08cxgb3: fix phy power downDivy Le Ray
2 phys are were not getting the Global Tx disable bit set when powered down, leading to an inconsistent link state on peer. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08cxgb3: AQ100X phy support updateDivy Le Ray
Add missing SUPPORTED_TP flag. Update FW version checking. Do the full initialization even if the FW version is unknown, it might help catching further issues. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08r6040: bump driver version to 0.24 and date to 08 July 2009Florian Fainelli
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08r6040: restore MIER register correctly when IRQ line is sharedFlorian Fainelli
When the r6040 device IRQ line is shared we will enter the driver interrupt service routine, mask off the device interrupt enable register (MIER) and return with IRQ_NONE, we would then leave the device with interrupts disabled, this patch fixes that issue. Reported-by: Steve Holland <sdh4@iastate.edu> Signed-off-by: Joe Chou <joe.chou@rdc.com.tw> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08davinci_emac: fix kernel oops when changing MAC address while interface is downPablo Bitton
Check that network interface is running before changing its MAC address. Otherwise, rxch is accessed when it's NULL - causing a kernel oops. Moreover, check that the new MAC address is valid. Signed-off-by: Pablo Bitton <pablo.bitton@gmail.com> Signed-off-by: Chaithrika U S <chaithrika@ti.com> Tested-by: Chaithrika U S <chaithrika@ti.com> [tested on DM6467 EVM] Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-08igb: set lan id prior to configuring phyAlexander Duyck
The igb driver was defaulting to using the lock for pci-e function 0 for all of the phys due to the fact that the lan id was not being set prior to initialization. This change makes it so that the function id is set prior to checking for the phy id. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-07MIPS: BCM63XX: Add integrated ethernet PHY support for phylib.Maxime Bizon
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> drivers/net/phy/Kconfig | 6 ++ drivers/net/phy/Makefile | 1 drivers/net/phy/bcm63xx.c | 132 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 139 insertions(+) create mode 100644 drivers/net/phy/bcm63xx.c Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-07tun: Remove a dead line of codePaul Moore
Remove an unnecessary assignment. Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-07ucc_geth: Add support for skb recyclingAnton Vorontsov
We can reclaim transmitted skbs to use in the receive path, so-called skb recycling support. Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly, thus maybe reclaim some skbs for rx. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-07hp-wmi: fix rfkill bugJohannes Berg
Fix the third (I think) polarity error I accidentally introduced in the rfkill rewrite to make wireless work again on (certain?) HP laptops. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-07iwmc3200wifi: add Kconfig helpSamuel Ortiz
We're missing a Kconfig help for the iwmc3200wifi driver. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-07ath9k: Fix leak in tx descriptorVasanthakumar Thiagarajan
When we reclaim the tx desc, we always assume that the last desc is a holding desc, which is not true, and skip it. If the tx queue is drained during channel change, internal reset and etc, the last descriptor may not be the holding descriptor and we fail to reclaim them. This results in the following two issues. 1. Tx stuck - We drop all the frames coming from upper layer due to shortage in tx desc. 2. Crash - If we fail to reclaim a tx descriptor, we miss to update the tx BA window with the seq number of the frame associated to that desc, which, at some point, result in the following crash due to an assert failure in ath_tx_addto_baw(). This patch fixes these two issues. kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180! [155064.304164] invalid opcode: 0000 [#1] SMP Call Trace: [<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k] [<fbbc9591>] ipv6? __ieee80211_tx+0x41/0x120 [mac80211] [<fbbcb5ae>] ? aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211] [<c037e501>] aes_generic? _spin_lock_irqsave+0x31/0x40 [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0 [<c03058b5>] ? __qdisc_run+0x1b5/0x200 [<fbbcda5a>] ? af_packetieee80211_select_queue+0xa/0x100 [mac80211] [<c02f53b7>] ? i915dev_queue_xmit+0x2e7/0x3f0 [<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211] [<c031bc35>] ? ip_output+0x55/0xb0 [<c02e0188>] ? show_memcpy_count+0x18/0x60 [<c02eb186>] ? __kfree_skb+0x36/0x90 [<c02f2202>] ? binfmt_miscdev_queue_xmit_nit+0xd2/0x110 [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0 [<c03058b5>] ? __qdisc_run+0x1b5/0x200 [<c033bca7>] ? scoarp_create+0x57/0x2a0 [<c02f53b7>] ? bridgedev_queue_xmit+0x2e7/0x3f0 [<c03034a0>] ? eth_header+0x0/0xc0 [<c033b95f>] stp? arp_xmit+0x5f/0x70 [<c033bf4f>] ? arp_send+0x5f/0x70 [<c033c8f5>] bnep? arp_solicit+0x105/0x210 [<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390 [<c013bf88>] ? run_timer_softirq+0x138/0x210 [<c02fa410>] ? ppdevneigh_timer_handler+0x0/0x390 [<c02fa410>] ? neigh_timer_handler+0x0/0x390 Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-07b43/b43legacy: fix radio LED initializationLarry Finger
Fix condition in which radio LED did not initialize correctly, and remove 4 compilation warnings. After the recent changes in rfkill, the radio LED used by b43/b43legacy did not always initialize correctly. Both b43 and b43legacy used the deprecated variable radio_enabled in struct ieee80211_conf. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-06drivers/net/cs89x0.c: Avoid using magic number in set_dma_modeJulia Lawall
The constant DMA_RX_MODE is defined to be 0x14 in the local include file cs89x0.h. Since a constant with the same name is used elsewhere with set_dma_mode, it seems likely that this constant could be used here. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ expression E1; identifier I; constant int C; @@ ( set_dma_mode(E1,I,...) | *set_dma_mode(E1,C,...) ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06fec: fix definition of 5272 version of FEC_X_DES_ACTIVE registerGreg Ungerer
fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register The ColdFire 5272 FEC driver has a different register address map than other users of the FEC driver. And its definition of the FEC_X_DES_ACTIVE register is incorrect, it should be 0x14. The fec interface cannot transmit data with the old value. Signed-off-by: Greg Ungerer <gerg@uclinux.org> ---- Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06fec: remove extra ";" from definition namesGreg Ungerer
Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06dm9000: add checksum offload supportYeasah Pell
Add checksum offload support for DM9000A and DM9000B chips. v2 changes: added a local copy of ip_summed to save IO cycles in dm9000_send_packet v3 changes: trans_start updating is removed. Signed-off-by: Yeasah Pell <yeasah@comrex.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06e1000: fix flow control thresholdsJesse Brandeburg
when testing the jumbo frames with pages patch, the stats would show rx_missed errors (dropped packets) even when connected to a link partner with flow control enabled. this indicates that for this MTU (9000) the flow control thresholds are not adjusting correctly. In fact, before this change, the FCRTH (xoff threshold) is 36864 when the fifo size is only 40000, with 9000 byte MTU. fix it so that we at least have room for one frame after we send the xoff. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06e1000: implement jumbo receive with partial descriptorsJesse Brandeburg
This is code extremely similar to what is committed in e1000e already. e1000 will no longer request 32kB slab buffers to support jumbo frames on PCI/PCI-X adapters. This will significantly reduce the likelyhood of order:3 allocation failures. This new code adds support for using pages as receive buffers, and the driver will chain multiple pages together to build a jumbo frame for OS consumption. The hardware takes a power of two buffer size and will dump as much data as it can receive into 1 or more buffers. The benefits of applying this are 1) stop akpm's dissing :-) of this lame e1000 behavior [1] 2) more efficient memory allocation (half) when using jumbo frames, which will also allow for much better socket utilization with jumbos since the socket is charged for the full allocation of each receive buffer, regardless of how much is used. 3) this was a feature request by a customer 4) copybreak for small packets < 256 bytes still applies [1] http://lkml.org/lkml/2008/7/10/68 http://article.gmane.org/gmane.linux.network/130986 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06e1000: allow ethtool coalesece to adjust interrupts per secondJesse Brandeburg
This patch allows on-the-fly adjustment of the interrupts per second generated by e1000 devices 82545/82546 (hardware support of ITR register is a requirement) adjust using this command: ethtool -C eth0 rx-usecs 10 where 10 is 10 microseconds per interrupt interval, so 10 = 100,000 interrupts per second, and 125 = 8000 interrupts per second. changes should be immediate. 1,3 are special values and indicate the automatic tuning mode to the driver, where 1 is 4000-90000 interrupts per second and 3 is 4000-20000 interrupts per second and is the driver default. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Advance driver version numberGuo-Fu Tseng
Advance driver version number after modifications. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Tuning rxsum functionGuo-Fu Tseng
1. Use more efficient way to determine flag status. 2. Hardware dose not mark fragment bit against IPv6 packets, print TCP/UDP checksum warning message for IPv4 packets only. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Remove shadow register supportGuo-Fu Tseng
The hardware failed to update the shadow register in several cases. It's known to be failed at 64bit box with more than 4G RAM. In order to make the device working stable, give up using the shadow register feature. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Change bufinf memory locationGuo-Fu Tseng
Instead of using a large chunk of memory space preserved for for modules, using kmalloc to obtain the needed memory. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Fix typoGuo-Fu Tseng
Fix enum typo in jme.h Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Fix unmatched tasklet_{enable|disable} pairGuo-Fu Tseng
Fix faulty tasklet function usage. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06jme: Some minor coding style consistency modificationsGuo-Fu Tseng
Making coding style more consistent. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06Revert "p54: Use SKB list handling helpers instead of by-hand code."David S. Miller
This reverts commit a1091aae19b1d9c85d91c86915a611387f67a26b.
2009-07-06tun/tap: Fix crashes if open() /dev/net/tun and then poll() it.Mariusz Kozlowski
Fix NULL pointer dereference in tun_chr_pool() introduced by commit 33dccbb050bbe35b88ca8cf1228dcf3e4d4b3554 ("tun: Limit amount of queued packets per device") and triggered by this code: int fd; struct pollfd pfd; fd = open("/dev/net/tun", O_RDWR); pfd.fd = fd; pfd.events = POLLIN | POLLOUT; poll(&pfd, 1, 0); Reported-by: Eugene Kapun <abacabadabacaba@gmail.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05net: convert remaining non-symbolic return values in ndo_start_xmit() functionsPatrick McHardy
This patch converts the remaining occurences of raw return values to their symbolic counterparts in ndo_start_xmit() functions that were missed by the previous automatic conversion. Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero is changed to explicitly use NETDEV_TX_OK. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Version updateSreenivasa Honnur
- Version update Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Printing the function's configured mode of operationSreenivasa Honnur
- Printing the function's configured mode of operation. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Disable fcs stripping.Sreenivasa Honnur
- Disable fcs stripping. The minimum frame size that can be received by the hardware is 57 Bytes. A 64 Byte Ethernet frame with the vlan tag and fcs stripped will result in a 56 Byte frame which will lock up the receive engine. The work around is to disable fcs stripping in the hardware which is done with a firmware upgrade. The fixes are - 1. Ensure that the correct firmware version is used. 2. Decrement the indicated packet length of the receive packet by 4 bytes (FCS length). Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Fixes in isr routineSreenivasa Honnur
- Fixes in isr routine Fixed crash with INTA mode during driver unload. Pass hldev to request_irq instead of vdev. Fixed Traffic failure with GRO in INTA mode. Pass the correct napi context to gro functions. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Removed the code to bounds check the mss valueSreenivasa Honnur
- Removed the code to bounds check the mss value. The hardware does bounds checking and will not allow an oversized mss to lockup the transmit path. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Corrected Register map entry for xmac_link registersSreenivasa Honnur
- Corrected Register map entry for xmac_link registers. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: check for card status before continuing in device closeSreenivasa Honnur
- Fixed the crash in rmmod after vpath open failed when trying to change mtu. We should check for card status before continuing in device close. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Fixed memory leak by freeing memory allocated for device_configSreenivasa Honnur
- Fixed memory leak by freeing memory allocated for device_config. Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05vxge: Removed ioremap of unused bar addresses and their referencesSreenivasa Honnur
- Removed ioremap of bar1 address Driver needs only bar0 address for register access - Removed references to bar1 and bar2 addresses Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05Minor code cleanup in drivers/net/r6040.cMichael Opdenacker
Replaced '0' by 'bar' in the probe function. The 'bar' variable was already set to '0' and is already used in pci_iomap(). This is cleaner and improves code consistency. Signed-off-by: Michael Opdenacker <michael@free-electrons.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functionsPatrick McHardy
This patch is the result of an automatic spatch transformation to convert all ndo_start_xmit() return values of 0 to NETDEV_TX_OK. Some occurences are missed by the automatic conversion, those will be handled in a seperate patch. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05net: remove NET_RX_BAD and NET_RX_CN* definesFlorian Westphal
almost no users in the tree; and the few that use them treat them like NET_RX_DROP. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2009-07-05forcedeth: Fix NAPI race.Eric Dumazet
Eric Dumazet a écrit : > Ingo Molnar a écrit : >>> The following changes since commit 52989765629e7d182b4f146050ebba0abf2cb0b7: >>> Linus Torvalds (1): >>> Merge git://git.kernel.org/.../davem/net-2.6 >>> >>> are available in the git repository at: >>> >>> master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master >> Hm, something in this lot quickly wrecked networking here - see the >> tx timeout dump below. It starts with: >> >> [ 351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c() >> [ 351.011815] Hardware name: System Product Name >> [ 351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out >> >> Config attached. Unfortunately i've got no time to do bisection >> today. > > > > forcedeth might have a problem, in its netif_wake_queue() logic, but > I could not see why a recent patch could make this problem visible now. > > CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 > is not a new cpu either :) > > forcedeth uses an internal tx_stop without appropriate barrier. > > Could you try following patch ? > > (random guess as I dont have much time right now) We might have a race in napi_schedule(), leaving interrupts disabled forever. I cannot test this patch, I dont have the hardware... Tested-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05drivers/net/smsc911x.c: Fix resource size off by 1 errorJulia Lawall
The call resource_size(res) returns res->end - res->start + 1 and thus the second change is semantics-preserving. res_size is then used as the second argument of a call to request_mem_region, and the memory allocated by this call appears to be the same as what is released in the two calls to release_mem_region. So the size argument for those calls should be resource_size(size) as well. Alternatively, in the second call to release_mem_region, the second argument could be res_size, as that variable has already been initialized at the point of this call. The problem was found using the following semantic patch: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ struct resource *res; @@ - (res->end - res->start) + 1 + resource_size(res) @@ struct resource *res; @@ - res->end - res->start + BAD(resource_size(res)) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05pcnet_cs: add new idKen Kawasaki
add new id (RIOS System PC CARD3 ETHERNET). Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-24 10:44:35 +0000