| Age | Commit message (Collapse) | Author |
|---|
|
Move xen_domain and related tests out of asm-x86 to xen/xen.h so they
can be included whenever they are necessary.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This uses %pRt and %pRf to print additional resource information (type,
size, prefetchability, etc.) consistently.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This uses %pRt to print additional resource information (type, size,
prefetchability, etc.) consistently.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
As a followup to 71a082efc9fdc12068a3cee6cebb1330b00ebeee, it's conceivable
that some vendors may expose PCI hotplug functionality through both vendor
mechanisms and ACPI. The native mechanism will generally be a superset of
any functionality provided via ACPI, so the acpiphp driver should always
be initialised after any others. Change the link order such that acpiphp
will not be initialised until any other statically linked drivers have had
an opportunity to claim the hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change PCI nomenclature according to
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
pci_dfl_cache_line_size is marked as __initdata but referenced by
pci_init() which is __devinit. Make it __devinitdata instead of
__initdata.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
For non hotplug PCI devices, the system firmware usually configures
CLS correctly. For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either. Unfortunately this leads to
poor performance for certain devices (sata_sil). Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.
This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.
Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
sparc64 is now the only user of PCI_CACHE_LINE_BYTES. Drop it and set
pci_dfl_cache_line_size from pcibios_init() instead and drop
PCI_CACHE_LINE_BYTES handling from generic pci code.
Orignally-From: David Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ironlake suspend/resume support
drm/i915: kill warning in intel_find_pll_g4x_dp
drm/i915: update watermarks before enabling PLLs
drm/i915: add FIFO watermark support for G4x
drm/i915: quiet DP i2c init
drm/i915: fix panel fitting filter coefficient select for Ironlake
drm/i915: fix to setup display reference clock control on Ironlake
drm/i915: Install a fence register for fbc on g4x
drm/i915: save/restore BLC histogram control reg across suspend/resume
drm/i915: Fix FDI M/N setting according with correct color depth
drm/i915: disable powersave feature for Ironlake currently
drm/i915: Fix render reclock availability detection.
drm/i915: Save and restore the GM45 FBC regs on suspend and resume.
drm/i915: Set the LVDS_BORDER when using LVDS scaling mode
drm/i915: disable FBC for Pineview, fixing a boot hang.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_via: Remove redundant device ID for VIA VT8261
drivers/ata/libata: Move dereference after NULL test
ahci: Enable SB600 64bit DMA on MSI K9A2 Platinum v2
|
|
Just remove redundant device ID for VIA VT8261.
The device ID 0x9000 and 0x9040 are redundant (for VT8261).
The 0x9040 is reserved for other usage.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
In each case, if the NULL test on qc is needed, then the derefernce
should be after the NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Like the Asus M2A-VM, MSI's K9A2 Platinum (MS-7376) can also support 64bit
DMA. It is a new enough board that all the BIOS releases work correctly with
64bit DMA enabled.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Remove some debug messages producing too much noise
PM: Fix warning on suspend errors
PM / Hibernate: Add newline to load_image() fail path
PM / Hibernate: Fix error handling in save_image()
PM / Hibernate: Fix blkdev refleaks
PM / yenta: Split resume into early and late parts (rev. 4)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio-keys - use IRQF_SHARED
Input: winbond-cir - select LEDS_TRIGGERS
Input: i8042 - try to get stable CTR value when initializing
Input: atkbd - add a quirk for OQO 01+ multimedia keys
|
|
* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-mpc: Do not generate STOP after read.
i2c: imx: disable clock when it's possible to save power.
i2c: imx: only imx1 needs disable delay
i2c: imx: check busy bit when START/STOP
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: check interface is down before type change
cfg80211: fix NULL ptr deref
libertas if_usb: Fix crash on 64-bit machines
mac80211: fix reason code output endianness
mac80211: fix addba timer
ath9k: fix misplaced semicolon on rate control
b43: Fix DMA TX bounce buffer copying
mac80211: fix BSS leak
rt73usb.c : more ids
ipw2200: fix oops on missing firmware
gre: Fix dev_addr clobbering for gretap
sky2: set carrier off in probe
net: fix sk_forward_alloc corruption
pcnet_cs: add cis of PreMax PE-200 ethernet pcmcia card
r8169: Fix card drop incoming VLAN tagged MTU byte large jumbo frames
ibmtr: possible Read buffer overflow?
net: Fix RPF to work with policy routing
net: fix kmemcheck annotations
e1000e: rework disable K1 at 1000Mbps for 82577/82578
e1000e: config PHY via software after resets
...
|
|
pm_runtime_idle() is somewhat noisy. Remove debug prints.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Fixes the point where we need to complete the power transition when
device suspend fails, so that we don't print warnings about devices
added to the device hierarchy after a failing suspend.
[rjw: Modified changelog.]
Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit 0c570cdeb8fdfcb354a3e9cd81bfc6a09c19de0c
(PM / yenta: Fix cardbus suspend/resume regression) caused resume to
fail on systems with two CardBus bridges. While the exact nature
of the failure is not known at the moment, it can be worked around by
splitting the yenta resume into an early part, executed during the
early phase of resume, that will only resume the socket and power it
up if there was a card in it during suspend, and a late part,
executed during "regular" resume, that will carry out all of the
remaining yenta resume operations.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14334, which is a
listed regression from 2.6.31.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported-by: Stephen J. Gowdy <gowdy@cern.ch>
Tested-by: Jose Marino <braket@hotmail.com>
|
|
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().
An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
drivers/input/misc/winbond-cir.c depends on LEDS_TRIGGERS so
add an appropriate select to drivers/input/misc/Kconfig
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
If user presses keys while i8042 is being initialized there is a chance
that keyboard data will be mistaken for results of Read Control Register
command causing futher troubles. Work around this issue by reading CTR
several times and stop when we get matching results.
Reported-and-tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).
This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Enable clock before START, disable it after STOP.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
check cpu_is_mx1() when disable delay.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.
If we don't check busy bit, START/STOP may fail on some fast CPUs.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
In commit c1c7af60892070e4b82ad63bbfb95ae745056de0 ("drm/i915: force
mode set at lid open time") the intel graphics driver was taught to
restore the LVDS mode on lid open.
That caused problems with interaction with the suspend/resume code,
which commonly runs at the same time (suspend is often caused by the lid
close event, while lid open is commonly a resume event), which was
worked around with in commit 06891e27a9b5dba5268bb80e41a283f51335afe7
("drm/i915: fix suspend/resume breakage in lid notifier").
However, in the meantime the lid event code had also grown a user event
notifier (commit 06324194eee97a51b5f172270df49ec39192d6cc: "drm/i915:
generate a KMS uevent at lid open/close time"), and now _that_ causes
problems with suspend/resume and some versions of Xorg reacting to those
uevents by setting the mode.
So this effectively reverts that commit 06324194ee, and makes the lid
open protection logic against suspend/resume more explicit. This fixes
at least one laptop. See
http://bugzilla.kernel.org/show_bug.cgi?id=14484
for more details.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: fix wireless drivers depends
Staging: wireless drivers Kconfig change
Staging: android: mark subsystem as broken
Staging: remove stlc45xx driver
Staging: rtl8187se/rtl8192e/rtl8192su: allow module unload
Staging: vt6656: fix the memory free bug in vntwusb_disconnect()
Staging: Panel: prevent driver from calling misc_deregister twice on same ressource
Staging: hv: fix oops in vmbus - missing #include
Staging: hv: fix oops in vmbus - netvsc list_head
Staging: hv: fix oops in vmbus - udev events
Staging: hv: Fix vmbus load hang caused by faulty data packing
Staging: hv: Fix null pointer error after vmbus loading
Staging: hv TODO patches
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fsl_udc_core: Fix kernel oops on module removal
USB: option: TLAYTECH TUE800 support
USB: r8a66597-hcd: fix cannot detect a device when uses_new_polling is set
USB: serial: sierra driver autopm fixes
USB: serial: sierra driver send_setup() autopm fix
USB: rndis_host: debug info clobbered before it is logged
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: Mark generic_serial users as BROKEN
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Documentation: ABI: /sys/devices/system/cpu/cpu#/node
Documentation: ABI: /sys/devices/system/cpu/cpuidle/
Documentation: ABI: /sys/devices/system/cpu/sched_[mc|smt]_power_savings
Documentation: ABI: /sys/devices/system/cpu/cpu#/ topology files
Documentation: ABI: /sys/devices/system/cpu/ topology files
Documentation: ABI: document /sys/devices/system/cpu/
Documentation: ABI: rename sysfs-devices-cache_disable properly
Driver core: allow certain drivers prohibit bind/unbind via sysfs
Driver core: fix driver_register() return value
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] smp: fix sigp sense handling
[S390] smp: fix sigp stop handling
[S390] cputime: fix overflow on 31 bit systems
[S390] call home: fix string length handling
[S390] call home: fix error handling in init function
[S390] smp: fix prefix handling of offlined cpus
[S390] s/r: cmm resume fix
[S390] call home: fix local buffer usage in proc handler
|
|
* 'for-linus' of git://neil.brown.name/md:
async_tx: fix asynchronous raid6 recovery for ddf layouts
async_pq: rename scribble page
async_pq: kill a stray dma_map() call and other cleanups
md/raid6: kill a gcc-4.0.1 'uninitialized variable' warning
raid6/async_tx: handle holes in block list in async_syndrome_val
md/async: don't pass a memory pointer as a page pointer.
md: Fix handling of raid5 array which is being reshaped to fewer devices.
md: fix problems with RAID6 calculations for DDF.
md/raid456: downlevel multicore operations to raid_run_ops
md: drivers/md/unroll.pl replaced with awk analog
md: remove clumsy usage of do_sync_mapping_range from bitmap code
md: raid1/raid10: handle allocation errors during array setup.
md/raid5: initialize conf->device_lock earlier
md/raid1/raid10: add a cond_resched
Revert "md: do not progress the resync process if the stripe was blocked"
|
|
Commit ef7562b7f28319e6dd1f85dc1af87df2a7a84832 ("dpt_i2o: Fix up
copy*user") had a silly typo: EINVAL should be -EINVAL.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: stable@kernel.org
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Platform drivers registered via platform_driver_probe() can be bound
to devices only once, upon registration, because discard their probe()
routines to save memory. Unbinding the driver through sysfs 'unbind'
leaves the device stranded and confuses users so let's not create
bind and unbind attributes for such drivers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In this patch:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=16dc42e018c2868211b4928f20a957c0c216126c
the check was added for another driver to already claim the same device
on the same bus. But the returned error code was wrong: to modprobe, the
-EEXIST means that _this_ driver is already installed. It therefore
doesn't produce the needed error message when _another_ driver is trying
to register for the same device. Returning -EBUSY fixes the problem.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
fsl_udc_release() calls dma_free_coherent() with an inappropriate
device passed to it, and since the device has no dma_ops, the following
oops pops up:
Kernel BUG at d103ce9c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [d103ce9c] fsl_udc_release+0x50/0x80 [fsl_usb2_udc]
LR [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc]
Call Trace:
[cfbc7dc0] [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc]
[cfbc7dd0] [c01a35c4] device_release+0x2c/0x90
[cfbc7de0] [c016b480] kobject_cleanup+0x58/0x98
[cfbc7e00] [c016c52c] kref_put+0x54/0x6c
[cfbc7e10] [c016b360] kobject_put+0x34/0x64
[cfbc7e20] [c01a1d0c] put_device+0x1c/0x2c
[cfbc7e30] [d103dbfc] fsl_udc_remove+0xc0/0x1e4 [fsl_usb2_udc]
...
This patch fixes the issue by passing dev->parent, which points to
a correct device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Li Yang <leoli@freescale.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add ID for Tlaytech TUE800 CDMA modem to the option driver.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-By: Matthias Urlichs <matthias@urlichs.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch presents fixes for the autosuspend feature implementation in
sierra usb serial driver in functions sierra_open(), sierra_close() and
stop_read_write_urbs().
The patch "sierra_close() must resume the device before it notifies it
of a closure" submitted by Oliver Neukum on Wed, October 14 has been
merged as fix in sierra_close() function.
The bug fix in sierra_open() function restores the autopm interface
state on error condition.
The bug fix in in stop_read_write_urbs() function assures that both
receive and interrupt urbs are recycled.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch presents a fix for the autosuspend feature implementation in
sierra usb serial driver for function sierra_send_setup(). Because it
is possible to call sierra_send_setup() before sierra_open() or after
sierra_close() we added a get/put interface activity to assure that the
usb control can happen even when the device is autosuspended.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Tested-by: Matthew Safar <msafar@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The MTU throttle-down if a RNDIS device doesn't support a particular
packet size is being incorrectly logged. The attempted packet size is
being clobbered before it gets logged.
First patch; please inform if I'm doing this incorrectly. Diff'd
against latest official source as per the FAQ; forward port to current
git version is straightforward.
Signed-off-by: George Nassar <george.nassar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These drivers can (erroneously) be enabled even when
CONFIG_NET=n, CONFIG_NETDEVICES=n, CONFIG_WLAN=n, etc.
Stop this.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Change the wireless drivers to depend on CONFIG_WLAN instead of
CONFIG_WLAN_80211 which is going away soon.
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It's causing lots of build errors, so just mark it as broken. It is
scheduled to be removed in 2.6.33 anyway.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It's no longer needed as the p54spi driver is the same thing,
under a different name and in the correct portion of the kernel tree.
Cc: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
