aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-03-27ACPICA: Preserve all PM control reserved and ignored bitsBob Moore
As per the ACPI specification, preserve (read/modify/write) all bits that are defined as either reserved or ignored (PM control control registers only.) Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-27ACPICA: Change handling of PM1 Status register ignored bitBob Moore
Ignored bits must be preserved according to the ACPI spec. Usually this means a read/modify/write when writing to the register. However, for status registers, writing a one means clear the event. Writing a zero means preserve the event (do not clear.) This behavior is clarified in the ACPI 4.0 spec, and the ACPICA code now simply always writes a zero to the ignored bit. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-27ACPICA: Fix AcpiWalkNamespace race condition with table unloadBob Moore
Added a reader/writer locking mechanism to allow multiple concurrent namespace walks (readers), but a dynamic table unload will have exclusive access to the namespace. This fixes a problem where a table unload could delete the portion of the namespace that is currently being examined by a walk. Adds a new file, utlock.c that implements the reader/writer lock mechanism. ACPICA BZ 749. http://www.acpica.org/bugzilla/show_bug.cgi?id=749 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-27ACPICA: FADT: Fix extraneous length mismatch warningBob Moore
Incorrect register length mismatch between the 32 and 64 bit registers in some cases. Code was was checking the wrong pointer for non-zero, should be looking at the address within the GAS structure. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-27ACPICA: Formatting update - no functional changesBob Moore
Split long lines, update comments. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-27ACPICA: Add manifest constants for bit register valuesBob Moore
Add and deploy constants for the PM status/enable/control registers. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Update table header print functionBob Moore
Cleanup table header output. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Restructure bit register access functionsBob Moore
Update code for acpi_read_bit_register and acpi_write_bit_register. Simplified code path, condensed duplicate code. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Rename ACPI bit register access functionsBob Moore
Rename acpi_get_register and acpi_set_register to clarify the purpose of these functions. New names are acpi_read_bit_register and acpi_write_bit_register. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Optimize ACPI register lockingBob Moore
Removed locking for reads from the ACPI bit registers in PM1 Status, Enable, Control, and PM2 Control. The lock is not required when reading the single-bit registers. The acpi_get_register_unlocked function is no longer needed and has been removed. This will improve performance for reads on these registers. ACPICA BZ 760. http://www.acpica.org/bugzilla/show_bug.cgi?id=760 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Formatting update - no functional changesBob Moore
Split some long lines. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Debug output: decrease verbosity of DB_INFO debug levelBob Moore
Removed some of the extraneous debug prints using the DB_INFO level. This should make the DB_INFO more useful. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Debug output: print result of _OSI invocationsBob Moore
Print input strings and the result (supported or not supported) for invocations of the _OSI method. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Conditionally compile acpi_set_firmware_waking_vector64Bob Moore
This function is only needed on 64-bit host operating systems. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Remove ACPI_GET_OBJECT_TYPE macroBob Moore
Remove all instances of this obsolete macro, since it is now a simple reference to ->common.type. There were about 150 invocations of the macro across 41 files. ACPICA BZ 755. http://www.acpica.org/bugzilla/show_bug.cgi?id=755 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Add function to handle PM1 control registersBob Moore
Added acpi_hw_write_pm1_control. This function writes both of the PM1 control registers (A/B). These registers are different than than the PM1 A/B status and enable registers in that different values can be written to the A/B registers. Most notably, the SLP_TYP bits can be different, as per the values returned from the _Sx predefined methods. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Remove redundant ACPI_BITREG_SLEEP_TYPE_BBob Moore
This type is the same as TYPE_A. Removed this and all related instances. Renamed SLEEP_TYPE_A to simply SLEEP_TYPE. ACPICA BZ 754. http://www.acpica.org/bugzilla/show_bug.cgi?id=754 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Fix parameter validation for acpi_read/writeBob Moore
Now return AE_BAD_PARAMETER if the input register pointer is null, and AE_BAD_ADDRESS if the register has an address of zero. Previously, these cases simply returned AE_OK. For optional registers such as PM1B status/enable/control, the caller should check for a valid register address before calling. ACPICA BZ 748. http://www.acpica.org/bugzilla/show_bug.cgi?id=748 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: For PM1B registers, do not shift value read or writtenBob Moore
The PM1B registers are mirrors of the PM1A registers with different bits actually implemented. From the ACPI specification: "Although the bits can be split between the two register blocks (each register block has a unique pointer within the FADT), the bit positions are maintained. The register block with unimplemented bits (that is, those implemented in the other register block) always returns zeros, and writes have no side effects" Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Remove extra write for acpi_hw_clear_acpi_statusBob Moore
This function was writing an optional PM1B status register twice. The existing call to the low-level acpi_hw_register_write automatically handles a possibly split PM1 A/B register. ACPICA BZ 751. http://www.acpica.org/bugzilla/show_bug.cgi?id=751 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Fix writes to optional PM1B registersBob Moore
On read, shift B register bits above the A bits. On write, shift B bits down to zero before writing the B register. New: acpi_hw_read_multiple, acpi_hw_write_multiple. These two functions now transparently handle the (possible) split registers for PM1 Status, Enable, and Control. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Update comments in module headerBob Moore
Enhance the explanations of the various package return types for clarity. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Check for non-zero address before being converted to GASLin Ming
Reported-by: FreeBSD community Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Split out PM1 status registers from the FADTBob Moore
Add new globals for the PM1 status registers (A/B), similar to the way the PM1 enable registers are handled. Instead of overloading the FADT Event Register blocks. This makes the code clearer and less prone to error. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Update FADT flag definitionsBob Moore
Add new flags in the Boot Architecture flags field. Update comments for all FADT flags. Add FADT version when each flag was defined. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Add override for dynamic tablesBob Moore
Add a call to acpi_os_table_override during the installation of a dynamic table (loaded via the Load or LoadTable AML operators). Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Remove extraneous parameter in table managerBob Moore
Removed the Flags parameter from several internal functions since it was not being used. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Allow OS override of all ACPI tablesBob Moore
Previously, the table override mechanism was implemented for the DSDT only. Now, any table in the RSDT/XSDT can be replaced by the host OS. (including the DSDT). Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-26ACPICA: Add error check to debug object dump routineBob Moore
Add check for invalid handle in acpi_ns_dump_one_object. Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits) ucc_geth: Fix oops when using fixed-link support dm9000: locking bugfix net: update dnet.c for bus_id removal dnet: DNET should depend on HAS_IOMEM dca: add missing copyright/license headers nl80211: Check that function pointer != NULL before using it sungem: missing net_device_ops be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle be2net: replenish when posting to rx-queue is starved in out of mem conditions bas_gigaset: correctly allocate USB interrupt transfer buffer smsc911x: reset last known duplex and carrier on open sh_eth: Fix mistake of the address of SH7763 sh_eth: Change handling of IRQ netns: oops in ip[6]_frag_reasm incrementing stats net: kfree(napi->skb) => kfree_skb net: fix sctp breakage ipv6: fix display of local and remote sit endpoints net: Document /proc/sys/net/core/netdev_budget tulip: fix crash on iface up with shirq debug virtio_net: Make virtio_net support carrier detection ...
2009-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix crash with /proc/iomem sparc64: Reschedule KGDB capture to a software interrupt. sbus: Auto-load openprom module when device opened.
2009-03-22ucc_geth: Fix oops when using fixed-link supportAnton Vorontsov
commit b1c4a9dddf09fe99b8f88252718ac5b357363dc4 ("ucc_geth: Change uec phy id to the same format as gianfar's") introduced a regression in the ucc_geth driver that causes this oops when fixed-link is used: Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc0151270 Oops: Kernel access of bad area, sig: 11 [#1] TMCUTU NIP: c0151270 LR: c0151270 CTR: c0017760 REGS: cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8) MSR: 00009032 <EE,ME,IR,DR> CR: 24024042 XER: 20000000 DAR: 00000000, DSISR: 20000000 TASK = cf81cba0[1] 'swapper' THREAD: cf81e000 GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80 cf86b08c GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000 0ffc81a0 GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c cf83f000 GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80 cf83f360 NIP [c0151270] ucc_geth_open+0x330/0x1efc LR [c0151270] ucc_geth_open+0x330/0x1efc Call Trace: [cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable) [cf81fba0] [c0187638] dev_open+0xbc/0x12c [cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0 This patch fixes the issue by removing offending (and somewhat duplicate) code from init_phy() routine, and changes _probe() function to use uec_mdio_bus_name(). Also, since we fully construct phy_bus_id in the _probe() routine, we no longer need ->phy_address and ->mdio_bus fields in ucc_geth_info structure. I wish the patch would be a bit shorter, but it seems like the only way to fix the issue in a sane way. Luckily, the patch has been tested with real PHYs and fixed-link, so no further regressions expected. Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22dm9000: locking bugfixDavid Brownell
This fixes a locking bug in the dm9000 driver. It calls request_irq() without setting IRQF_DISABLED ... which is correct for handlers that support IRQ sharing, since that behavior is not guaranteed for shared IRQs. However, its IRQ handler then wrongly assumes that IRQs are blocked. So the fix just uses the right spinlock primitives in the IRQ handler. NOTE: this is a classic example of the type of bug which lockdep currently masks by forcibly setting IRQF_DISABLED on IRQ handlers that did not request that flag. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22net: update dnet.c for bus_id removalStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22radeonfb: Whack the PCI PM register until it sticksBenjamin Herrenschmidt
This fixes a regression introduced when we switched to using the core pci_set_power_state(). The chip seems to need the state to be written over and over again until it sticks, so we do that. Note that the code is a bit blunt, without timeout, etc... but that's pretty much because I put back in there the code exactly as it used to be before the regression. I still add a call to pci_set_power_state() at the end so that ACPI gets called appropriately on x86. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Raymond Wooninck <tittiatcoke@gmail.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-21dnet: DNET should depend on HAS_IOMEMIlya Yanok
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21dca: add missing copyright/license headersMaciej Sosnowski
In two dca files copyright and license headers are missing. This patch adds them there. Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19sungem: missing net_device_opsStephen Hemminger
Sungem driver only got partially converted to net_device_ops. Since this could cause bugs, please push this to 2.6.29 Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycleSathya Perla
This is a patch to reconfigure vlan-ids during an i/f down/up cycle Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19be2net: replenish when posting to rx-queue is starved in out of mem conditionsSathya Perla
This is a patch to replenish the rx-queue when it is in a starved state (due to out-of-mem conditions) Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: fix waitqueue usage in hiddev HID: fix incorrect free in hiddev
2009-03-18Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller
2009-03-18bas_gigaset: correctly allocate USB interrupt transfer bufferTilman Schmidt
Every USB transfer buffer has to be allocated individually by kmalloc. Impact: bugfix, no functional change Signed-off-by: Tilman Schmidt <tilman@imap.cc> Tested-by: Kolja Waschk <kawk@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18smsc911x: reset last known duplex and carrier on openSteve Glendinning
smsc911x_phy_adjust_link is called periodically by the phy layer (as it's run in polling mode), and it only updates the hardware when it sees a change in duplex or carrier. This patch clears the last known values every time the interface is brought up, instead of only when the module is loaded. Without this patch the adjust_link function never updates the hardware after an ifconfig down; ifconfig up. On a full duplex link this causes the tx error counter to increment, even though packets are correctly transmitted, as the default MAC_CR register setting is for half duplex. The tx errors are "no carrier" errors, which should be ignored in full-duplex mode. When MAC_CR is set to "full duplex" mode they are correctly ignored by the hardware. Note that even with this patch the tx error counter can increment if packets are transmitted between "ifconfig up" and the first phy poll interval. An improved solution would use the phy interrupt with phylib, but I haven't managed to make this work 100% robustly yet. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18sh_eth: Fix mistake of the address of SH7763Nobuhiro Iwamatsu
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong. This revise it. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18sh_eth: Change handling of IRQNobuhiro Iwamatsu
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was changed. This revises it for this change. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18tulip: fix crash on iface up with shirq debugKyle McMartin
Tulip is currently doing request_irq before it has done its initialization. This is usually not a problem because it hasn't enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler when registering the interrupt as a sanity check. This can result in a NULL ptr dereference, so call tulip_init_ring before request_irq, and add a free_ring function to do the freeing now shared with tulip_close. Tested with a shell loop running ifup, ifdown in a loop a few hundred times with DEBUG_SHIRQ on. Signed-off-by: Kyle McMartin <kyle@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18virtio_net: Make virtio_net support carrier detectionPantelis Koukousoulas
Impact: Make NetworkManager work with virtio_net For now the semantics are simple: There is always carrier. This allows a seamless experience with e.g., qemu/kvm where NetworkManager just configures and sets up everything automagically. If/when a generally agreed-upon way to control carrier on/off in the emulator/hypervisor level emerges, it will be trivial to extend the driver to support that too, but for now even this 2-liner makes user experience that much better. Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18bonding: Fix updating of speed/duplex changesJay Vosburgh
This patch corrects an omission from the following commit: commit f0c76d61779b153dbfb955db3f144c62d02173c2 Author: Jay Vosburgh <fubar@us.ibm.com> Date: Wed Jul 2 18:21:58 2008 -0700 bonding: refactor mii monitor The un-refactored code checked the link speed and duplex of every slave on every pass; the refactored code did not do so. The 802.3ad and balance-alb/tlb modes utilize the speed and duplex information, and require it to be kept up to date. This patch adds a notifier check to perform the appropriate updating when the slave device speed changes. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18bnx2: Fix problem of using wrong IRQ handler.Michael Chan
The MSI-X handler was chosen before the call to pci_enable_msix(). If MSI-X was not available, the wrong MSI-X handler would be used in INTA mode. This would cause a screaming interrupt problem because INTA would not be cleared by the MSI-X handler. Fixed by assigning MSI-X handler after pci_enable_msix() returns successfully. Also update version to 1.9.3. Thomas Chenault <thomas_chenault@dell.com> helped us find this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>