| Age | Commit message (Collapse) | Author |
|---|
|
Trial to see if (mainly 32-bit) memcpy is any better than u16 loop
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
The delay versions of the access to registers were based on a misunderstanding of
the Glamo docs: it can force nWAIT differently depending on the access type. Therefore
we don't need to take special care about delays on CPU side.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Rather than using conservative default timings for the NAND flash,
use the timings as specified in the S3C2442B MCP data sheet.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Removed unused variable.
Signed-off-by: Nelson Castillo <nelsoneci@gmail.com>
|
|
The function glamo_mci_reset is not being used. Let's comment it out.
Signed-off-by: Nelson Castillo <nelsoneci@gmail.com>
|
|
This patch carries over the OpenMoko modifications at
include/asm-arm/arch-s3c2410/spi-gpio.h to
arch/arm/mach-s3c2410/include/mach/spi-gpio.h
Note: board_size and board_info have been removed upstream, but as we
still rely on them we'll just put them back for now. These will need to
be removed (and the corresponding driver changes made, of course) before
this can go upstream.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
This pulls the Moko changes to regs-sdi.h that were in
include/asm-arm/arch-s3c2410 over to the file at arch/arm/../mach and
deletes the file at include/asm-arm.
Note: we have been using a mix of regs-sdi.h from the two different
locations. The unification of these two files may have some unknown
consequences... keep your eyes open for oddities after applying this.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Remove unneeded spaces and coding style fixes. Purely cosmetic.
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This file was moved in the big file move, but some OpenMoko specific
changes did not make it. This patch peels out the relevant bits and
adds them to the gpio.h file in the upstream location.
The only OpenMoko specific change is the definition of gpio_to_irq and
irq_to_gpio. These functions should really be defined in gpio_chip and
asm-generic/gpio.h; this is coming soon, but until then we'll just use
the Moko definitions that we've been using up until now.
This is not strictly correct for the GTA02 case, but it works given
the configuration that's currently in use. This can be fixed (and
should become evident) when the configuration options are cleaned up.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
This file is OpenMoko specific and didn't get moved in the big file
move. Move it to arch/arm/mach-s3c2410/include/mach where it belongs
and fix the references to it.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
After the big include file move these paths ended up incorrect. Fix
these so that this builds cleanly again.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
buttons in FSO?]
Michael 'Mickey' Lauer wrote:
...
> The problem is (and this is the reason why I'm crossposting this to the
> kernel mailing list), the kernel is not swallowing the power button
> presses that triggers the resume, so you need some "real" programming
> (as opposed to the expressional complexity of our rules) in order to
> prevent falling asleep right after resume.
>
> Kernel-guys, can we change that?
suppress-resume-onkey-event.patch
This suppresses the key press and key release events from the
power button, in the case where the power button is the wake
event for the GTA01 or GTA02 device.
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
|
LED trigger gets removed in led_brightness_store???
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
Move to level from edge, fix local_save... to local_irq...
simplify bitbang sequence
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
Remove unsued PWM stuff around LEDs.
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
Adds AC and USB powersupply objects, and a workqueue to automonitor
changes in battery state and fire change events on any change to
selected registers.
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
Add /sys files for jack state reporting.
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
This patch implements fb_blank() for the glamo-fb driver, which switches off
the pixel clock (DCLK) for power saving.
We currently delay the actual pixel clock switch until we enter
FB_BLANK_POWERDOWN, since the backlight fade is slow and we don't want the
user to see artefacts on the screen while the backlight is fading out.
So since the X server first sends FB_BLANK_{V,H}SYNC_SUSPEND, we start the
backlight fade here, and only once we get FB_BLANK_POWERDOWN the pixel clock is
disabled.
There are no measurements yet, but the power savings should be double, since
there is no longer any generation of the high-frequency LCM signals, and
there are no video-related SDRAM accesses anymore.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
the comment claims that DHCLK is enabled, while the
code actually disables it.
No code change, purely cosmetic patch.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
Remove dead code and coding style fixes. Purely cosmetic.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
Qi does not touch the backlight, we have to do it in Linux now
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
FB_BLANK events and switch the JBT6K74 LCM controller into
its power saving mode.
This has the potential of saving something like 50mW during screen blank.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
Thomas White noticed that the recent patch from Andrzej cleaning up a
nasty cast in the resume_dependency stuff for Glamo broke resume. The
problem was that the wrong resume callback was arrived at by the new
code, the one in the device's device_driver struct rather than the
struct platform_driver that actually holds the right pointer.
Since this code will be gone in 2.6.26, I reverted this part of Andrzej's
patch, tidying the cast a bit anyway.
Reported-by: Thomas White <taw27@cam.ac.uk>
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This function (set_brightness) may be called in interrupt context and
therefore should not sleep; use a spin_lock instead of a mutex to ensure
this.
This should take care of the following BUG:
[21474678.340000] BUG: sleeping function called from invalid context at kernel/mutex.c:207
[21474678.340000] in_atomic():1, irqs_disabled():0
[21474678.340000] no locks held by python/1255.
[21474678.340000] [<c002d928>] (dump_stack+0x0/0x18) from [<c003b08c>] (__might_sleep+0xdc/0xf8)
[21474678.340000] [<c003afb0>] (__might_sleep+0x0/0xf8) from [<c02efc08>] (mutex_lock_nested+0x2c/0x264)
[21474678.340000] r5:c03ed754 r4:c03ed6dc
[21474678.340000] [<c02efbdc>] (mutex_lock_nested+0x0/0x264) from [<c022e180>] (neo1973_vib_vib_set+0x2c/0x6c)
[21474678.340000] [<c022e154>] (neo1973_vib_vib_set+0x0/0x6c) from [<c022e6a4>] (led_timer_function+0x8c/0xb4)
[21474678.340000] r6:c041a1a0 r5:c7f34820 r4:0000012c
[21474678.340000] [<c022e618>] (led_timer_function+0x0/0xb4) from [<c004aeb4>] (run_timer_softirq+0x180/0x20c)
[21474678.340000] r5:c7f3482c r4:00000102
[21474678.340000] [<c004ad34>] (run_timer_softirq+0x0/0x20c) from [<c0046368>] (__do_softirq+0x64/0xd8)
[21474678.340000] r8:00000000 r7:00000001 r6:0000000a r5:c0419ff8 r4:00000041
[21474678.340000] [<c0046304>] (__do_softirq+0x0/0xd8) from [<c0046764>] (irq_exit+0x48/0x5c)
[21474678.340000] r6:00000000 r5:c03d128c r4:0000001e
[21474678.340000] [<c004671c>] (irq_exit+0x0/0x5c) from [<c0028050>] (__exception_text_start+0x50/0x68)
[21474678.340000] [<c0028000>] (__exception_text_start+0x0/0x68) from [<c0028a8c>] (__irq_usr+0x4c/0xe0)
[21474678.340000] Exception stack(0xc7d7bfb0 to 0xc7d7bff8)
[21474678.340000] bfa0: 0055bb3a 0000004a 00000000 0055baf0
[21474678.340000] bfc0: 0000004a 0052ae30 00000025 005168e0 00000073 00000025 401281ec 00000000
[21474678.340000] bfe0: 0000006f be9b8470 006e0069 400a8844 60000010 ffffffff
[21474678.340000] r6:00004000 r5:f4000000 r4:ffffffff
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
When the config option MACH_NEO1973_GTA02 is not set, then we do not need to
have any access to the FIQ symbols.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Attached is a patch that has greatly reduced the frequency of failures
to resume (due to an oops from the glamo resume handler), and the
dreaded "white screen after resume". I can't say that it fixes all of
these, although I have yet to see the white-screen since applying this
patch and suspending/resuming several hundred times (with the 30-second
suspend on the 2008.8 image and the endless stream of GSM error messages
generated by something in that image, it has proved to be very useful to
do an automated stress test!)
This patch will apply to stable, and should make stable slightly more,
well, "stable".
[Feel free to remove the debug messages if someone feels strongly about
that; I left them in because I think they might be useful in triaging
further crashes; I'm not at all convinced that this patch will fix all
the cases of resume failures.]
[[And, yes, this is ugly, really ugly.]]
[[[Oh yeah - there's still one extreme case that will result in an oops:
if a dependent driver is built as a module, and it is unloaded, and it
happened that the preceding suspend/resume was aborted, and that abort
happened between the dependent driver and the driver upon which it is
dependent, then a list entry will be left behind referencing the
unloaded module. There's just no good way to fix that given the way the
resume dependency plumbing is connected up right now, so just avoid
using modules for any of the drivers involved in the resume dependency
stuff.]]]
Regards,
Mike (mwester)
commit 905d2fc9c45f622418ce9ef4e67c23453aab7571
Author: Mike Westerhof <mwester@dls.net>
Date: Mon Aug 11 11:11:25 2008 -0500
always-call-resume-dependencies.patch
Ensure that a dependent resume handler is always executed,
even if the resume handler for driver upon which it is
dependent never suspends (and therefore never resumes either).
Also make sure that we do not end up with duplicate
dependencies registered, something that can happen if the
suspend is aborted due to driver failure or an early resume
(such as occurs when the GSM interrupts during suspend).
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
|
I hit this when updating to 2.6.26. Also if CONFIG_MMC is enabled this
patch converts this horrible horrible hack into a horrible hack by using
dev->resume() (untested).
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
|
|
This patch adds another module parameter to glamo-mci which sets the
SD Card clock rate used inbetween powering the card and the completion of
the first bulk transfer. You can set it from kernel commandline like this.
glamo_mci.sd_post_power_clock=1000000
The period between changing the power state and the first bulk transfer
completion is critical because larger SDHC cards take longer to initialize
before they can service the bulk transfer, and the Glamo MMC unit has a
fixed timeout length of a maximum of 4095 x 16 x SD Card clocks. Large
cards like 8GB Sandisk SDHC are not ready before this timeout is used up
at default 16MHz.
Subsequently, the card can handle 16MHz SD Clock and timeout durations
okay.
By default this patch operates the SD Clock at only 1MHz until the first
bulk transfer is completed after each powerup action from the MCI stack. It
also keeps the SD Clock running during this time, and disables the SD Clock
if the card is not present and the MCI stack removes power.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
I needed the following two changes for g_ether to work with last
week's stable-tracking and no CONFIG_DEBUG_FS. I don't know if
they're related to moko patches, if not I can send them upstream
isntead.
BTW I need to boot off the SD card now because mtd only returns CRC
errors and doesn't mount. Does it work for other people?
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
|
|
- pca9632 is a LED driver which will be adopted in gta03.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
|
|
This patch is a work-around solution to correct charging indication logic.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
|
|
This patch allows ESSID with length 1, which were rejected because the
stack assumed iwconfig used a different format in the ioctl's payload.
It also refuses ESSIDs longer than 31 bytes, because there is some
buffer overrun issue buried somewhere else in the stack. In principle,
32 bytes should be fine.
Open issue:
- where is the 32 bytes overrun ?
Signed-off-by: Werner Almesberger <werner@openmoko.org>
|
|
This is purely cosmetic, but annoying.
The ar6k wifi driver does not print a newline after the informational message when disconnecting from an AP. This leads to cluttered dmesg output like the following:
AR6000 disconnected from 00:02:cf:85:c6:08 AR6000 connected event on freq 2412 with bssid 00:02:cf:85:c6:08 listenInterval=100, beaconInterval = 100, beaconIeLen = 0 assocReqLen=27 assocRespLen =22
What is expected, is something like:
AR6000 disconnected from 00:02:cf:85:c6:08
AR6000 connected event on freq 2412 with bssid 00:02:cf:85:c6:08 listenInterval=100, beaconInterval = 100, beaconIeLen = 0 assocReqLen=27 assocRespLen =22
The upside of this is that it gives me a nice simple patch to send in as my first contribution to OpenMoko?.
Cheers
Signed-off-by: mattb <mattb@openmoko-trac.invalid>
|
|
Hi all.
I'm seeing a behavior in my freerunner where light taps on the
touchscreen are not registered as clicks by the kernel even though the
base hardware does report clicking events. I'm seeing the kernel
generate extra "unclick" events in these cases. It looks like in the
driver, an unclick event is processed before the click event, thus
suppressing the click from ever being generated. I'm attaching a patch
that addresses this. I'm now able to type much faster on the matchbox
keyboard, even when using my fingertips instead of fingernails.
Dima
Signed-off-by: Dima Kogan <dkogan@cds.caltech.edu>
|
|
Possible implementation of SD Card corruption workaround reported here
https://docs.openmoko.org/trac/ticket/1802#comment:5
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Some boots from Qi trigger a symptom from this interesting race -->
[ 2.730000] Unable to handle kernel NULL pointer dereference at virtual address 00000248
[ 2.730000] pgd = c0004000
[ 2.735000] [00000248] *pgd=00000000
[ 2.735000] Internal error: Oops: 5 [#1] PREEMPT
[ 2.735000] Modules linked in:
[ 2.735000] CPU: 0 Not tainted (2.6.24-stable10_0c1587137aaf0ee3-mokodev #1071)
[ 2.735000] PC is at pcf50633_voltage_set+0x1c/0xfc
[ 2.735000] LR is at gta02_glamo_mmc_set_power+0xdc/0x128
[ 2.735000] pc : [<c01df570>] lr : [<c0034324>] psr: 60000013
[ 2.735000] sp : c7c57eb0 ip : c7c57ec8 fp : c7c57ec4
[ 2.735000] r10: c7cfca28 r9 : 00000000 r8 : c7c57f68
[ 2.735000] r7 : c7cfca68 r6 : c7cfcae0 r5 : 00000c80 r4 : 00000000
[ 2.735000] r3 : 00000000 r2 : 00000c80 r1 : 0000000a r0 : 00000c80
[ 2.735000] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 2.735000] Control: c000717f Table: 30004000 DAC: 00000017
[ 2.735000] Process kmmcd (pid: 102, stack limit = 0xc7c56268)
[ 2.735000] Stack: (0xc7c57eb0 to 0xc7c58000)
[ 2.735000] 7ea0: c0608c58 00000c80 c7c57edc c7c57ec8
[ 2.735000] 7ec0: c0034324 c01df564 c7cfca28 c7cfc800 c7c57f1c c7c57ee0 c0194de0 c0034258
[ 2.735000] 7ee0: c7c57f34 c7c57ef0 c01e6230 c005de5c 60000013 c7cfca28 c7cfc800 60000013
[ 2.735000] 7f00: c7cfca68 c7c57f68 00000000 c01e6778 c7c57f34 c7c57f20 c01e5d68 c0194da8
[ 2.735000] 7f20: c7cfc800 c7cfca08 c7c57f5c c7c57f38 c01e6810 c01e5cbc c0059278 c7c57f48
[ 2.735000] 7f40: c02d2ba0 00000002 c7c44420 c7c56000 c7c57f9c c7c57f60 c00592e0 c01e6788
[ 2.735000] 7f60: 00000002 c0059278 c0608d74 c04321cc c036e16c 00000000 c7c57fb0 c7c44420
[ 2.735000] 7f80: c7c56000 00000000 00000000 00000000 c7c57fd4 c7c57fa0 c005a068 c00591ec
[ 2.735000] 7fa0: c02d0624 00000000 c7c4c0e0 c005dc2c c7c57fb0 c7c57fb0 00000000 c7c56000
[ 2.735000] 7fc0: c7c44420 c0059f84 c7c57ff4 c7c57fd8 c005db28 c0059f94 00000000 00000000
[ 2.735000] 7fe0: 00000000 00000000 00000000 c7c57ff8 c004b170 c005dad8 ffffffff ffffffff
[ 2.735000] Backtrace:
[ 2.735000] [<c01df554>] (pcf50633_voltage_set+0x0/0xfc) from [<c0034324>] (gta02_glamo_mmc_set_power+0xdc/0x128)
[ 2.735000] r5:00000c80 r4:c0608c58
[ 2.735000] [<c0034248>] (gta02_glamo_mmc_set_power+0x0/0x128) from [<c0194de0>] (glamo_mci_set_ios+0x48/0x254)
[ 2.735000] r5:c7cfc800 r4:c7cfca28
[ 2.735000] [<c0194d98>] (glamo_mci_set_ios+0x0/0x254) from [<c01e5d68>] (mmc_power_up+0xbc/0x100)
[ 2.735000] [<c01e5cac>] (mmc_power_up+0x0/0x100) from [<c01e6810>] (mmc_rescan+0x98/0x1a8)
[ 2.735000] r5:c7cfca08 r4:c7cfc800
[ 2.735000] [<c01e6778>] (mmc_rescan+0x0/0x1a8) from [<c00592e0>] (run_workqueue+0x104/0x208)
[ 2.735000] r6:c7c56000 r5:c7c44420 r4:00000002
[ 2.735000] [<c00591dc>] (run_workqueue+0x0/0x208) from [<c005a068>] (worker_thread+0xe4/0xf8)
[ 2.735000] [<c0059f84>] (worker_thread+0x0/0xf8) from [<c005db28>] (kthread+0x60/0x94)
[ 2.735000] r6:c0059f84 r5:c7c44420 r4:c7c56000
[ 2.735000] [<c005dac8>] (kthread+0x0/0x94) from [<c004b170>] (do_exit+0x0/0x6f4)
[ 2.735000] r6:00000000 r5:00000000 r4:00000000
[ 2.735000] Code: e351000a e1a04000 e1a00002 8a000032 (e5943248)
[ 2.745000] ---[ end trace 123ec1d286354824 ]---
This problem was caused by insufficient timeout waiting for pcf50633 to resume
and broken code to detect timeout exhaustion.
Although I'd like to think it has something to do with mmc resume woes it should make a panic
and subsequent emergency spew on UART2 if that had been the case.
Took the opportunity to move the stuff to show completion of probe to later in the
pcf50633 probe and tighten readiness test.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Fix all of the mismatches Andrzej put us on to.
Found-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: Andy Green <andy@openmoko.com>
|
