aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2008-04-28atmel_lcdfb: wiring BGR to RGB color modeNicolas Ferre
Adds different wiring mode for the LCD screen. The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead "RGB-565". The major part of graphic stacks for embedded systems uses only "RGB-565". It is possible to swap LCD IOs instead of doing this bit swapping by software (See application note AT91SAM9 LCD Controller http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf) This wire swapping is done on the at91sam9rl-ek board (board code using this patch will come later). Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28atmel_lcdfb: suspend/resume supportDavid Brownell
Teach atmel_lcdfb driver how to suspend/resume. Note that the backlight control should probably do more of the same stuff: turning off display power (more than just the backlight) and stopping the clocks (and dma to drive the no-longer-seen display). No point in wasting power to generate images that can't be observed, after all... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28atmel_lcdfb: don't initialize a pre-allocated framebufferHaavard Skinnemoen
If the user specified a fixed framebuffer address on the command line, it may have been initialized already with a splash image or something, so we shouldn't clear it. Therefore, we should only initialize the framebuffer if we allocated it ourselves. This patch also updates the AVR32 setup code to clear the framebuffer if it allocated it itself, i.e. the user didn't provide a fixed address or the reservation failed. I've updated the at91 platform code as well so that it initializes the framebuffer if it is located in SRAM, but I haven't tested that it actually works. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com> Cc: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbdev: framebuffer_alloc() fixesOndrej Zajicek
Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb. Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbdev: vt8623fb: better resume from STROndrej Zajicek
After resume from STR, image is shifted by 8 pixels to the left. This patch fixes it. Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28savagefb: speed up the I2C busJean Delvare
There is no reason to drive the savagefb I2C bus at such a low speed, so bump it from 12.5 kbps to 50 kbps. The Intel (i810) and Matrox framebuffer drivers already run their I2C bus at this speed, and so are the legacy i2c-savage4 and i2c-prosavage drivers. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28drivers/video/imsttfb.c: add missing curly bracketsRoel Kluin
in #if 0 inactivated function msttfb_load_cursor_image() the call eieio() occurs after rather than in the loop due to missing curly brackets. Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28uvesafb: don't treat valid modes returned byfb_find_mode() as errorsMichal Januszewski
Don't treat valid modes returned by fb_find_mode() (best-fit modes, default modes or the first valid mode) as errors. Currently, when fb_find_mode() finds a valid mode belonging to one of the above-mentioned classes, uvesafb will ignore it and will try to set a 640x480 video mode. The expected behaviour (introduced by this patch) would be to use the valid mode returned by fb_find_mode() instead. Signed-off-by: Michal Januszewski <spock@gentoo.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28radeonfb: speed up the I2C busesJean Delvare
There is no reason to drive the radeon I2C buses at such a low speed, so bump it from 12.5 kbps to 50 kbps. The Intel (i810) and Matrox framebuffer drivers already run their I2C bus at this speed. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28radeonfb: drop redundant RTRACE macroJean Delvare
RTRACE() does exactly the same thing as the standard pr_debug() call, so just use the latter. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28radeonfb: fix debug optionJean Delvare
Fix CONFIG_FB_RADEON_DEBUG. DEBUG must be defined before including any kernel header, otherwise dev_dbg() resolves to a no-op. Also, when debugging is disabled, don't set DEBUG at all instead of setting it to 0, to comply with what the kernel headers expect. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28radeonfb: use PCI device id in hex for name stringAndreas Herrmann
Additionally provide PCI device id in character format if possible. (The printable characters were commonly used to identify the cards.) Signed-off-by: Andreas Herrmann <aherrman@arcor.de> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28drivers/video/aty/aty128fb.c: fix incorrect usage of strncat in aty128_init()Roel Kluin
Fix incorrect length for strncat by replacing it with strlcat Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbdev: add removed option "mode" to keep compatibilityKrzysztof Helt
Add removed option "mode" to keep compatibility with existing setups. The option is back for pm2fb, tridentfb and vt8623fb drivers. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28s3fb: add option mode_optionKrzysztof Helt
Add the option "mode_option". It also moves mtrr variable to devinitdata section. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28arkfb: add option mode_optionKrzysztof Helt
Add the option "mode_option". This is one step toward changing all fb drivers to have common "mode_option" parameter. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28vt8623fb: change option mode to mode_optionKrzysztof Helt
Change the option "mode" into "mode_option". This is one step toward changing all fb drivers to have common "mode_option" parameter. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28pm3fb: change option mode to mode_optionKrzysztof Helt
Add the option "mode_option". This is one step toward changing all fb drivers to have common "mode_option" parameter. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28tridentfb: change option mode to mode_optionKrzysztof Helt
Change the option "mode_option" into "mode". It also adds __init attribute to tridentfb_setup function. This is one step toward changing all fb drivers to have common "mode_option" parameter. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Alain Kalker <miki@dds.nl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28pm2fb: change option mode to mode_optionKrzysztof Helt
Change the option "mode_option" into "mode". This is one step toward changing all fb drivers to have common "mode_option" parameter. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Alain Kalker <miki@dds.nl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28video/aty/atyfb_base.c: free when fb can't be registeredRoel Kluin
Free buffer when the framebuffer can't be registered Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbmem: fix con2fbmap limit checkPeter Samuelson
Fix limit check in FBIOPUT_CON2FBMAP ioctl. Signed-off-by: Peter Samuelson <peter@p12n.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28PM/gxfb: add hook to PM console layer that allows disabling of suspend VT switchAndres Salomon
Prior to suspend, we allocate and switch to a new VT; after suspend, we switch back to the original VT. This can be slow, and is completely unnecessary if the framebuffer we're using can restore video properly. This adds a hook that allows drivers to select whether or not to do this vt switch, and changes the gxfb driver to call this hook. It also adds a module param to gxfb to allow controlling of the vt switch (defaulting to no switch). (Note: I'm not convinced that console_sem is the best way to protect this, but we should probably have some form of locking..) [akpm@linux-foundation.org: build fix] Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: add power management functionalityAndres Salomon
This adds the ability to suspend/resume the gxfb driver, which includes: - The addition of a Graphics Processor register table in gxfb.h, and associated GP handling. - Register and palette saving code; registers are stored in gxfb_par. A few MSR values are saved as well. - gx_powerup and gx_powerdown functions which restore/save registers and enable/disable graphic engines. - gxfb_suspend/gxfb_resume Originally based on a patch by Jordan Crouse. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: stop sharing code with gx1fbAndres Salomon
We want to stop sharing stuff with gx1fb; it makes little sense. There were fields in geodefb_par that weren't being used, there was little point to the DC/VP ops callbacks, etc. This implements the following: - Create gxfb_par (based on geodefb_par), place it in gxfb.h - Drop display_gx.h and video_gx.h. The last few patches moved most stuff into gxfb.h anyways, so there was very little left. - Drop the geode_{dc,vid}_ops stuff. Un-static functions, add declarations to gxfb.h. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: move MSR bit fields into gxfb.hAndres Salomon
This continues the gxfb header cleanups. MSRs are defined in geode.h; the specific bits we care about are defined in gxfb.h. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: clean up register definitionsAndres Salomon
This does the following in preparation for register saving: - moves the register definitions from video_gx.h and display_gx.h into gxfb.h. - renames GX_* registers to match their section (ie, VP_). - renames register bitfields to match the data sheet (ie, DC_DCFG_TGEN -> DC_DISPLAY_CFG_TGEN). - for DC registers, rather than defining to specific addresses, use an enum to number them sequentially and just multiply by 4(bytes) to access them (in read_dc/write_dc). - for VP and FP registers, use an enum and multiple by 8 (bytes). They're 64bit registers. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: create DC/VP/FP-specific handlers rather than using readl/writelAndres Salomon
This creates read_dc/write_dc, read_vp/write_vp, and read_fp/write_fp for reading and updating those registers. It creates gxfb.h to house these. We also drop a no-op readl() from gx_set_mode. Other than that, there should be no functionality change. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: replace FBSIZE config option with a module parameterAndres Salomon
Use a command line option (vram) rather than hardcoding the vram size. LxFB already does this; it's useful for machines that can't query the BIOS for fb size. This patch originated from David Woodhouse, was modified by Jordan Crouse, and was then modified further by me. This also adds some gxfb documentation in Documentation/fb. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: use PCI_DEVICE() for gxfb's pci device tableAndres Salomon
Drop the class/class_mask stuff; it's unnecessary as long as the vendor and device IDs match. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: don't enable the CRT DACs when we are in flatpanel modeJordan Crouse
When the FP strap is enabled, don't turn on the CRT DACs - that will save about 35 mA of power. Updated/cleaned up by Andres Salomon. Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gxfb: set the right registers to tweak the sync polarityJordan Crouse
While running in flatpanel mode it is important to change the FP sync bits (VG register 0x408) rather then the CRT sync bits (VG register 0x008). This patch keeps the CRT sync bits at default when a flatpanel exists. Note that this also fixes inverted logic; we want CRT_VSYNC_POL to be set (ie, vsync is normally high) when FB_SYNC_VERT_HIGH_ACT is unset. Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28x86: geode: MSR cleanupAndres Salomon
This cleans up a few MSR-using drivers in the following manner: - Ensures MSRs are all defined in asm/geode.h, rather than in misc places - Makes the naming consistent; cs553[56] ones begin with MSR_, GX-specific ones start with MSR_GX_, and LX-specific ones start with MSR_LX_. Also, make the names match the data sheet. - Use MSR names rather than numbers in source code - Document the fact that the LX's MSR_PADSEL has the wrong value in the data sheet. That's, uh, good to note. Signed-off-by: Andres Salomon <dilinger@debian.org> Acked-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbcon: replace mono_col macro with static inlineHarvey Harrison
Use __u32 for max_len to match the declaration of length in the struct fb_bitfield. Suppresses sparse shadowed variable warnings from the nested max() macros: drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one drivers/video/console/fbcon.h:130:8: originally declared here drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one drivers/video/console/fbcon.h:130:8: originally declared here drivers/video/console/fbcon.h:130:8: warning: symbol '_y' shadows an earlier one drivers/video/console/fbcon.h:130:8: originally declared here [akpm@linux-foundation.org: fix constness] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28pm2fb: correct error values returned from probe functionKrzysztof Helt
Fix error values returned in some code branches in the pm2fb_probe() function. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbdev: use DIV_ROUND_UP or roundupJulia Lawall
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) / (d)) but is perhaps more readable. An extract of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @haskernel@ @@ #include <linux/kernel.h> @depends on haskernel@ expression n,d; @@ ( - (n + d - 1) / d + DIV_ROUND_UP(n,d) | - (n + (d - 1)) / d + DIV_ROUND_UP(n,d) ) @depends on haskernel@ expression n,d; @@ - DIV_ROUND_UP((n),d) + DIV_ROUND_UP(n,d) @depends on haskernel@ expression n,d; @@ - DIV_ROUND_UP(n,(d)) + DIV_ROUND_UP(n,d) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28powerpc: offb: add support for foreign endiannessAnton Vorontsov
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fb: add support for foreign endiannessAnton Vorontsov
Add support for the framebuffers with non-native endianness. This is done via FBINFO_FOREIGN_ENDIAN flag that will be used by the drivers. Depending on the host endianness this flag will be overwritten by FBINFO_BE_MATH internal flag, or cleared. Tested to work on MPC8360E-RDK (BE) + Fujitsu MINT framebuffer (LE). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: <Valdis.Kletnieks@vt.edu> Cc: Clemens Koller <clemens.koller@anagramm.de> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28fbdev: make the best-fit section of fb_find_mode return the closest matching ↵Michal Januszewski
mode Currently, if a perfect match in terms of resolution is not found, fb_find_mode() only looks for a best-fit mode among modes with a higher resolution than the one requested. Thus, if the user requests a resolution higher than the largest supported one, they are dropped to the default mode (usually a low resolution one). Change this behaviour so that all valid video modes are considered when looking for a best-fit mode, while still preferring modes with a higher resolution. Signed-off-by: Michal Januszewski <spock@gentoo.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gpiochip_reserve()Anton Vorontsov
Add a new function gpiochip_reserve() to reserve ranges of gpios that platform code has pre-allocated. That is, this marks gpio numbers which will be claimed by drivers that haven't yet been loaded, and thus are not available for dynamic gpio number allocation. [akpm@linux-foundation.org: remove unneeded __must_check] [david-b@pacbell.net: don't export gpiochip_reserve (section fix)] Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gpiolib: dynamic gpio number allocationAnton Vorontsov
If gpio_chip->base is negative during registration, gpiolib performs dynamic base allocation. This is useful for devices that aren't always present, such as GPIOs on hotplugged devices rather than mainboards. (This behavior was previously specified but not implemented.) To avoid using any numbers that may have been explicitly assigned but not yet registered, this dynamic allocation assigns GPIO numbers from the biggest number on down, instead of from the smallest on up. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gpio: define gpio_is_valid()Guennadi Liakhovetski
Introduce a gpio_is_valid() predicate; use it in gpiolib. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> [ use inline function; follow the gpio_* naming convention; work without gpiolib; all programming interfaces need docs ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gpiolib: i2c/spi drivers: handle rmmod betterGuennadi Liakhovetski
Use the newly introduced owner field in struct gpio_chip to protect the current (small) set of non-SOC GPIO drivers from being unloaded while any of their GPIOs are in use. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> [ add mcp23s08 and pcf857x ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28gpiolib: better rmmod infrastructureGuennadi Liakhovetski
As long as one or more GPIOs on a gpio chip are used its driver should not be unloaded. The existing mechanism (gpiochip_remove failure) doesn't address that, since rmmod can no longer be made to fail by having the cleanup code report errors. Module usecounts are the solution. Assuming standard "initialize struct to zero" policies, this change won't affect SOC platform drivers. However, drivers for external chips (on I2C and SPI busses) should be updated if they can be built as modules. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> [ gpio_ensure_requested() needs to update module usecounts too ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28isdn: rename CONFIG_AVMB1_COMPAT to not look like a Kconfig variableRobert P. J. Day
Since CONFIG_AVMB1_COMPAT is not a Kconfig variable, move it out of the Kconfig namespace. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28capifs: fix memory leak on remountCyrill Gorcunov
capifs_remount may reach 'return' statement without freeing of memory allocated by kstrdup call Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28hisax: depend on CONFIG_PNP, not __ISAPNP__Bjorn Helgaas
The PNP driver interfaces depend on CONFIG_PNP, so test that rather than __ISAPNP__. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28isdn: fix obvious cut-and-paste error in st5481_usb.cRobert P. J. Day
Fix a rather obvious cut-and-paste error, where earlier code for the controller URB got somehow mixed in with code for the interrupt URB. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28isdn: replace remaining __FUNCTION__ occurrencesHarvey Harrison
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28eicon: fix sparse integer as NULL pointer warningsHarvey Harrison
drivers/isdn/hardware/eicon/message.c:745:47: warning: Using plain integer as NULL pointer drivers/isdn/hardware/eicon/message.c:761:45: warning: Using plain integer as NULL pointer drivers/isdn/hardware/eicon/message.c:9122:16: warning: Using plain integer as NULL pointer drivers/isdn/hardware/eicon/message.c:9147:16: warning: Using plain integer as NULL pointer drivers/isdn/hardware/eicon/message.c:9173:14: warning: Using plain integer as NULL pointer drivers/isdn/hardware/eicon/divasmain.c:396:23: warning: Using plain integer as NULL pointer Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Karsten Keil <kkeil@suse.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-13 21:19:50 +0000