| Age | Commit message (Collapse) | Author |
|---|
|
The phy_id specified for the Vitesse 824x PHY would never match because
it was expecting bits to be set that would be masked by the phy_id_mask.
Fix the phy_id so it will match properly, and changed the mdio_bus_match
to mask both the driver and devices phy_id with the mask so we dont have
this issue in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: kill ATA_HORKAGE_DMA_RW_ONLY
libata: use PIO for non-16 byte aligned ATAPI commands
libata: call ata_check_atapi_dma() with qc better prepared
libata: fix infinite EH waiting bug
libata: fix ata_dev_disable()
pata_it821x: fix section mismatch warning
libata: remove unused variable from ata_eh_reset()
libata: be less verbose about hpa
libata: kill non-sense warning message
libata: kill the infamous abnormal status message
HPT374 is UDMA100 not UDMA133
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
2.6.22: ERROR: "__ucmpdi2" [drivers/net/s2io.ko] undefined!
cxgb3 - fix register to stop bc/mc traffic
au1000_eth: Fix warnings.
|
|
This adds support for some of the XGI Volari family that are based on the
SiS.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ATA_HORKAGE_DMA_RW_ONLY for TORiSAN is verified to be subset of using
DMA for ATAPI commands which aren't aligned to 16 bytes. As libata
now doesn't use DMA for unaligned ATAPI commands, the horkage is
redundant. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The IDE driver used DMA for ATAPI commands if READ/WRITE command is
multiple of sector size or sg command is multiple of 16 bytes. For
libata, READ/WRITE sector alignment is guaranteed by the high level
driver (sr), so we only have to worry about the 16 byte alignment.
This patch makes ata_check_atapi_dma() always request PIO for all data
transfer commands which are not multiple of 16 bytes.
The following reports are related to this problem.
http://bugzilla.kernel.org/show_bug.cgi?id=8605 (confirmed)
http://thread.gmane.org/gmane.linux.kernel/476620 (confirmed)
https://bugzilla.novell.com/show_bug.cgi?id=229260 (probably)
Albert first pointed out the difference between IDE and libata. Kudos
to him.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In atapi_xlat(), prepare qc better before calling
ata_check_atapi_dma() such that ata_check_atapi_dma() can use info
from qc. While at it, reformat weird looking if/else block in the
function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When EH gives up after repeated exceptions, it doesn't't clear the
PENDING bit on exit which leaves PENDING bit set without EH actually
scheduled. This makes ata_port_wait_eh() to wait forever makes rmmod
hang on such port. Fix it by clearing the flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix silly condition check bug in ata_dev_disable().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix section mismatch when CONFIG_HOTPLUG=n (but functions are used
for resume):
WARNING: drivers/ata/pata_it821x.o(.text+0x3f): Section mismatch: reference to .init.text: (between 'it821x_reinit_one' and 'it821x_program_udma')
WARNING: drivers/ata/pata_it821x.o(.text+0x691): Section mismatch: reference to .init.text: (between 'it821x_init_one' and 'it821x_passthru_set_dmamode')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Removed unused variable did_followup_srst from ata_eh_reset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
There's no reason to print out hpa related messages when HPA is not
active. Kill the unconditional message and add a warning message
which is printed if HPA size is smaller than the current size.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
prereset() is now allowed to set flag for unsupported reset method.
EH layer is responsible for selecting the fallback. Remove non-sense
warning message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Propogate change from drivers/ide
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
On Tue, Jun 19, Stephen Hemminger wrote:
> Olaf Hering <olaf@aepfle.de> wrote:
> > What happend to __ucmpdi2 from David Woodhouse?
> > google has a few hits about stuff like this on 32bit powerpc with gcc 4.1.2:
> >
> > ERROR: "__ucmpdi2" [drivers/net/s2io.ko] undefined!
> >
> > using the drivers/net/s2io* files from 2.6.21 with 2.6.22-rc5 fixes the
> > compile.
> >
> > 25805dcf9d83098cf5492117ad2669cd14cc9b24 adds two u64 >>= 48 followed by
> > a switch statement (line 2889 and 6816).
>
> Probably the "switch(err) {" needs a cast to a smaller type (like u8).
This change removes the compiler-generated calls to __ucmpdi2.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use the right register to stop broadcast/multicast traffic.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixed by including <linux/dma-mapping.h>:
CC drivers/net/au1000_eth.o
drivers/net/au1000_eth.c: In function 'au1000_probe':
drivers/net/au1000_eth.c:661: warning: implicit declaration of function 'dma_alloc_noncoherent'
drivers/net/au1000_eth.c:802: warning: implicit declaration of function 'dma_free_noncoherent'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reported by Grzegorz Chimosz <gchimi@gmail.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb_unlink_urb() is asynchronous, therefore an URB's buffer may not
be freed without waiting for the completion handler. This patch switches
to usb_kill_urb(), which is synchronous.
Thanks to Alan for making me look at the remaining users of usb_unlink_urb()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usblcd currently has no way to limit memory consumption by fast writers.
This is a security problem, as it allows users with write access to this
device to drive the system into oom despite resource limits.
Here's the fix taken from the modern skeleton driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
this is a classical memory leak in the ioctl handler. The buffer is simply
never freed. This fixes it the obvious way.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
you are submitting an URB with GFP_KERNEL holding a spinlock.
In this case the spinlock can be dropped earlier.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
New changes in the signal-handling code require compensating changes
in g_file_storage. This patch (as913) by Oleg Nesterov makes the
code use allow_signal() instead of sigprocmask().
From: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Make skb_seq_read unmap the last fragment
[NET]: Re-enable irqs before pushing pending DMA requests
[TCP] tcp_read_sock: Allow recv_actor() return return negative error value.
[PPP]: Fix osize too small errors when decoding mppe.
[PPP]: Revert 606f585e363527da9feaed79465132c0c661fd9e
[TIPC]: Fix infinite loop in netlink handler
[SKBUFF]: Fix incorrect config #ifdef around skb_copy_secmark
[IPV4]: include sysctl.h from inetdevice.h
[IPV6] NDISC: Fix thinko to control Router Preference support.
[NETFILTER]: nfctnetlink: Don't allow to change helper
[NETFILTER]: nf_conntrack_sip: add missing message types containing RTP info
|
|
The stallion driver oopses while initializing ISA cards due to an
uninitialized variable. This patch changes the initialisation order to
match the PCI code path.
Signed-off-by: Ingo Korb <ml@akana.de>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When binding the driver, check the ID register for a valid identity, in case
the SM501 is not functioning correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ensure that the M1XCLK and MCLK are sourced from the same PLL (and refuse to
bind the driver if they are not).
Update the PCI to safe initialisation values, as 72MHz is the maximum clock
for 33MHz PCI bus mastering.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The order of the set and mask operation in sm501_init_reg() was setting and
then masking the bits set. Correct the order so that we do not end up with
288MHz SDRAM clocks on certain systems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This init sequence of setting the SDRAM clock before the bus clock is
recommend by Silicon Motion to stop problems with writes not sticking into
registers.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds support for suspending the core (mfd driver) of the SM501.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recently my console UTF-8 patch went mainline. Here is an additional patch
that fixes two nasty issues and improves a third one, namely:
1. My patch changed the behavior if a glyph is not found in the Unicode
mapping table. Previously for Unicode values less than 256 or 512 the
kernel tried to display the glyph from that position of the glyph table,
which could lead to a different accented letter being displayed. I
removed this fallback possibility and changed it to display the
replacement symbol.
As Behdad pointed out, some fonts (e.g. sun12x22 from the kbd package)
lack Unicode mapping information, hence all you get is lots of question
marks. Though theoretically it's actually a user-space bug (the font
should be fixed), Behdad and I both believe that it'd be good to work
around in the kernel by re-introducing the fallback solution for ASCII
characters only. This sounds a quite reasonable decision, since all fonts
ship the ASCII characters in the first 128 positions. This way users
won't be surprised by lots of question marks just because s/he issued a
not-so-perfectly parameterized setfont command. As this fallback is only
re-introduced for code points below 128, you still won't see an accented
letter replaced by another, but at least you'll always get the English
letters right.
2. My patch introduced "question mark with inverted color attributes" as a
last resort fallback glyph. Though it perfectly works on VGA console, on
framebuffer you may end up with question marks that are highlighed but
shouldn't be, and normal characters that are accidentally highlighed.
This is caused by missing FLUSHes when changing the color attribute.
3. I've updated the table of double-width character based on Markus's
updated version. Only ten new code poings (one interval) is added.
Signed-off-by: Egmont Koblinger <egmont@uhulinux.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mppe_decompress() function required a buffer that is 1 byte too
small when receiving a message of mru size. This fixes buffer
allocation to prevent this from occurring.
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This can cause packet buffer overflows in certain cases,
the real bug will be fixed differently in a followon
changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Always disable/enable interrupts in the acpi idle routine,
even in the error path.
This is required as the 2.6.20 change in git commit d331e739f5ad2aaa9...
"Fix interrupt race in idle callback" expects the idle handler
to enable interrupt before returning.
There was a case in acpi idle routine, in which interrupt was not being
enabled before return, which caused the system to hang at bootup, while
enabling C-states on an SMP system.
The signature of the hang was that "processor.nocst"
was required to enable boot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Include PPC_MAC in the default too, not only MAC which only covers
m68k MACs.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Correct max_srq_wr returned from mlx4_ib_query_device()
IPoIB/cm: Remove dead definition of struct ipoib_cm_id
IPoIB/cm: Fix interoperability when MTU doesn't match
IPoIB/cm: Initialize RX before moving QP to RTR
IB/umem: Fix possible hang on process exit
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] intel_agp: don't load if no IGD and AGP port
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] unwinder improvements
[PARISC] Fix unwinder on 64-bit kernels
[PARISC] Handle wrapping in expand_upwards()
[PARISC] stop lcd driver from stripping initial whitespace
|
|
Signed-off-by: Julian Stecklina <der_julian@web.de>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
|
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
It's completely unused.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
If ib_umem_release() is called after ib_uverbs_close() sets context->closing,
then a process can get stuck in a D state, because the code boils down to
if (down_write_trylock(&mm->mmap_sem))
down_write(&mm->mmap_sem);
which is obviously a stupid instant deadlock. Fix the code so that we
only try to take the lock once.
This bug was introduced in commit f7c6a7b5 ("IB/uverbs: Export
ib_umem_get()/ib_umem_release() to modules") which fortunately never
made it into a release, and was reported by Pete Wyckoff <pw@osc.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
After i915 chip, GMCH has no AGP port. Origin bridge driver in device
table will try to access illegal regs like APBASE, APSIZE, etc. This
may cause problem.
So mark them as NULL in the table, we won't load if no IGD got detect
and bridge has no AGP port.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
fix module_param mistake in it821x
ahci: fix PORTS_IMPL override
kerneldoc fix in libata
libata: more NONCQ devices
pata_it821x: (partially) fix DMA in RAID mode
PATA: Add the MCP73/77 support to PATA driver
|
|
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
