aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-12-26ucc_geth: Don't needlessly change MAC settings in adjust_link()Anton Vorontsov
If PHY doesn't have an IRQ, phylib would poll for link changes, and would call adjust_link() every second. In that case we disable and enable the controller every second. Let's better check if there is actually anything changed, and, if so, change the MAC settings. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-26ucc_geth: Fix netdev watchdog triggering on link changesAnton Vorontsov
Since commit 864fdf884e82bacbe8ca5e93bd43393a61d2e2b4 ("ucc_geth: Fix hangs after switching from full to half duplex") ucc_geth driver disables the controller during MAC configuration changes. Though, disabling the controller might take quite awhile, and so the netdev watchdog might get upset: NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out ------------[ cut here ]------------ Badness at c02729a8 [verbose debug info unavailable] NIP: c02729a8 LR: c02729a8 CTR: c01b6088 REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e) [...] NIP [c02729a8] dev_watchdog+0x280/0x290 LR [c02729a8] dev_watchdog+0x280/0x290 Call Trace: [c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable) [c0451d50] [c00377c4] run_timer_softirq+0x164/0x224 [c0451da0] [c0032a38] __do_softirq+0xb8/0x13c [c0451df0] [c00065cc] do_softirq+0xa0/0xac [c0451e00] [c003280c] irq_exit+0x7c/0x9c [c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c [...] This patch fixes the issue by detaching the netdev during the time we change the configuration. Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Cc: Stable <stable@vger.kernel.org> [2.6.32] Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-26ucc_geth: Fix empty TX queue processingAnton Vorontsov
Following oops was seen with the ucc_geth driver: Unable to handle kernel paging request for data at address 0x00000058 Faulting instruction address: 0xc024f2fc Oops: Kernel access of bad area, sig: 11 [#1] [...] NIP [c024f2fc] skb_recycle_check+0x14/0x100 LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver] Call Trace: [df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable) [df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver] [df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8 [df857e10] [c0032a38] __do_softirq+0xb8/0x13c [df857e60] [c00065cc] do_softirq+0xa0/0xac [...] This is because ucc_geth_tx() tries to process an empty queue when queues are logically stopped. Stopping the queues doesn't disable polling, and since nowadays ucc_geth_tx() is actually called from the polling routine, the oops above might pop up. Fix this by removing 'netif_queue_stopped() == 0' check. Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Cc: Stable <stable@vger.kernel.org> [2.6.32] Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-25vxge: use DMA_BIT_MASK instead of plain values.Denis Kirjanov
Use DMA_BIT_MASK instead of plain values. Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-25bnx2x: Initialize cnic status block during chip resetMichael Chan
When the device is reset during MTU change, ring size change, or self test, etc, the cnic status block needs to be properly initialized if cnic is registered. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-25Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-12-23net/via-rhine: Fix scheduling while atomic bugsJarek Poplawski
There are BUGs "scheduling while atomic" triggered by the timer rhine_tx_timeout(). They are caused by calling napi_disable() (with msleep()). This patch fixes it by moving most of the timer content to the workqueue function (similarly to other drivers, like tg3), with spin_lock() changed to BH version. Additionally, there is spin_lock_irq() moved in rhine_close() to exclude napi_disable() etc., also tg3's way. Reported-by: Andrey Rahmatullin <wrar@altlinux.org> Tested-by: Andrey Rahmatullin <wrar@altlinux.org> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23ixgbe: fix Need to call pci_save_state after pci_restore_stateDon Skidmore
This patch adds a pci_save_state() call in ixgbe_resume() after pci_restore_state(). A similar change was made in ixgbe_io_slot_reset() that accommodates pci_restore_state() new behavior. This change makes pci_restore_state() clear the saved_state flag This is necessary due to a resent kernel change to pci_restore_state() so that it now clears the saved_state flag of the device right after the device.s standard configuration registers have been poplulated with the previously saved values. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: whitespace cleanup; #define cleanup; more verbose err msgScott Feldman
Some misc changes to cleanup whitespace issues and fix/remove some #define HW defintions. 1) fix some whitespace issues 2) more verbose err msg when resources aren't available to configure vnic 3) remove unused #define 4) fix RSS #define rss hash types Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: feature add: add ethtool -c/C supportScott Feldman
Only rx_usec and tx_usec options for ethtool -C are settable as those are the only settings that make sense to HW. Adds driver reporting of intr coalescing timer value in usec units rather than HW units. Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: Bug fix: align desc ring sizes to 32 descsScott Feldman
Previous driver was aligning ring sizes to 16 descs, but hardware actually wants desc ring sizes to be aligned to 32 descs. Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: minimize pkt filter updates to firmwareScott Feldman
In set_multicast(), only push pkt filter changes down to firmware if pkt filter actually changes. Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: Bug fix: try harder to fill Rx ring on skb allocation failuresScott Feldman
During dev->open(), make sure we get at least one skb on the Rx ring. Otherwise abort the interface load. Also, if we get skb allocation failures in NAPI poll while trying to replenish the ring, try again later so we don't end up starving out the Rx ring completely. Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23enic: Bug fix: use safe queue shutdown in dev->stopScott Feldman
Fix dev->stop shutdown bug where driver was stopping xmit queue and then disabling intrs. Fix is to disable intrs first and then stop the xmit queue, otherwise an interrupt could cause the queue to be rewoken. Also, no need to explicitly do queue servicing because queues are cleaned and reset back to initial state at end of dev->stop. Servicing queues also had the side-effect of also rewakening the xmit queue, which is not what we want. Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23be2net: Bug fix to return correct values in ethtool get_settings.Sarveshwar Bandi
Changes to return correct values for transceiver and supported in ethtool get_settings function. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23be2net: Bug fix to config NIC appropriately before loopback testSarveshwar Bandi
NIC controller has to be set to an appropriate mode before doing a loopback test. Test will fail otherwise. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23be2net: Bug fix to avoid soft lockup in loopback test.Sarveshwar Bandi
This change ensures that loopback test command gives up after 4 seconds when the hardware is not responsive. This could happen if the ports are connected properly in loopback mode. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23igbvf: Make igbvf error message more informativeWilliams, Mitch A
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23igb: check both function bits in status register in wol exceptionAlexander Duyck
The ethtool code for enabling Wake on Lan was not correctly checking the status register bits so as a result ports 0 and 2 were both being allowed to set WOL to enabled even though it is only supported on the first port for our adapters. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23igb: correctly offset 82575 flow control watermarks by 16 bytesAlexander Duyck
The watermark values for the 82575 were not being set correctly. As a result the high and low watermark values were set to the same value which can lead to excess xon/xoff packets being generated. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23igb: do not force retry count to 1 on 82580 phyAlexander Duyck
This change resolves an issue seen in some configurations where the link may drop to 100Mb/s even though the link itself supports 1000Mb/s. The issue was root caused to the fact that we were only trying the link once. Now instead we will try up to 5 attempts on a faulty cable before downshifting to 100Mb/s. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23igb: do not force pcs link when in KX modeAlexander Duyck
We were forcing the PCS link up in error when we are in KX mode. We should only be disabling autoneg, not forcing the link up. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: Disable TX descriptor prefetch watchdogBen Hutchings
This hardware watchdog can misfire, so it does more harm than good. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: QT2025C: Add error message for suspected bad SFP+ cablesBen Hutchings
Some cables have EEPROMs that conflict with the PHY's on-board EEPROM so it cannot load firmware. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: QT2025C: Work around PHY firmware initialisation bugMatthew Slattery
The PHY's firmware very occasionally appears to lock up very early, but with the heartbeat update still running. Rebooting the microcontroller core seems to be sufficient to recover. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: QT2025C: Switch into self-configure mode when not in loopbackMatthew Slattery
The PHY boots in a mode which is not necessarily optimal. This change switches it to self-configure mode (except when in loopback, which won't work in that mode if an SFP+ module is not present) by rebooting the PHY's microcontroller, and replicating the sequence of configuration writes from the boot EEPROM with the appropriate changes. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: QT2025C: Work around PHY bugMatthew Slattery
If we see the PHY remaining stuck in a link-down state due to PCS being down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back, which usually unsticks it. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: Fix DMA mapping cleanup in case of an error in TSONeil Turton
We need buffer->len to remain valid to work out the correct address to be unmapped. We therefore need to clear buffer->len after the unmap operation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: Include XGXS in XMAC link status check except in XGMII loopbackBen Hutchings
The XGXS block may not get a link immediately in XGXS or XAUI loopback modes, so we still need to check it. Split falcon_xaui_link_ok() into falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and falcon_xmac_link_ok(), which checks one or both sides of the link as appropriate. Also rename falcon_check_xaui_link() to falcon_xmac_link_ok_retry(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23sfc: Move PHY software state initialisation from init() into probe()Steve Hodgson
This prevents efx->link_advertising from being blatted during a reset. The phy_short_reach sysfs node is now destroyed later in the port shutdown process, so check for STATE_RUNNING after acquiring the rtnl_lock (just like in set_phy_flash_cfg). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23iwmc3200top: simplify imwct_txTomas Winkler
1. remove address argument since we use same address IWMC_SDIO_DATA_ADDR in all cases 2. add __iwmct_tx - non locking tx function for already locked contexts Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23iwmc3200top: cleanup log messagesTomas Winkler
1. add TRACE level 2. use TRACE where needed to reduce the noise 3 don't INFOEX from driver 4. add DUMP level for packets dumps 5. use correct context for the log messages Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23iwmc3200top: clean up fw_downloadTomas Winkler
1. removed redundant NULL-pointers checks in iwmct_fw_load as release_firmware and kfree are NULL pointer friendly 2. remove redundant memset of the parser since the structure is fully initialized in iwmct_fw_parser_init function Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23netxen: fix unified fw size checkAmit Kumar Salecha
o Unified firmware image size can be < 1 MB Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23netxen: support pci error handlersAmit Kumar Salecha
o Support pci error detection and recovery. o Refactor suspend and resume code, to share with io_error_detected, and slot_reset callbacks o NX_NEED_AER device state added, to synchronize with firmware recovery. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23netxen: fix tx timeout recoveryAmit Kumar Salecha
o In case of tx timeout, firmare may be healthy, but some pci-func may see no response from it. Force firmware reset, if some pci-func explicitly requests so. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23netxen: minor suspend resume fixesAmit Kumar Salecha
o pci device should be disable at the end and it should be enable first. o Interface should be attached(netif_device_attach()) irrespective of its state. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-23Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2009-12-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits) USB: Fix a bug on appledisplay.c regarding signedness USB: option: support hi speed for modem Haier CE100 USB: audio gadget: free alsa devices when unloading USB: audio gadget: fix wTotalLength calculation usb: otg: isp1301_omap: fix compile error USB: musb: workaround Blackfin FIFO anomalies USB: musb: Fix array index out of bounds issue USB: musb: Fix null pointer dereference issue USB: musb: correct DMA address for tx USB: musb: gadget_ep0: avoid SetupEnd interrupt USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled USB: musb: do not work if no gadget driver is loaded USB: musb: gadget: set otg tranceiver to idle when registering gadget USB: musb: Populate the VBUS GPIO with the correct GPIO number USB: musb: MAINTAINERS: Fix my tree's address USB: musb: fix compiling warning with min() macro USB: musb: move musb_remove to __exit USB: musb_gadget: fix kernel oops in txstate() USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header ...
2009-12-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: devtmpfs: unlock mutex in case of string allocation error Driver core: export platform_device_register_data as a GPL symbol driver core: Prevent reference to freed memory on error path Driver-core: Fix bogus 0 error return in device_add() Driver core: driver_attribute parameters can often be const* Driver core: bin_attribute parameters can often be const* Driver core: device_attribute parameters can often be const* Doc/stable rules: add new cherry-pick logic vfs: get_sb_single() - do not pass options twice devtmpfs: Convert dirlock to a mutex
2009-12-23USB: Fix a bug on appledisplay.c regarding signednesspancho horrillo
brightness status is reported by the Apple Cinema Displays as an 'unsigned char' (u8) value, but the code used 'char' instead. Note that he driver was developed on the PowerPC architecture, where the two types are synonymous, which is not always the case. Fixed that. Otherwise the driver will interpret brightness levels > 127 as negative, and fail to load. Signed-off-by: pancho horrillo <pancho@pancho.name> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: option: support hi speed for modem Haier CE100Donny Kurnia
I made this patch for usbserial driver to add the support for EVDO modem Haier CE100. The bugs report for this is here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/490068 This patch based on these post: http://blankblondtank.wordpress.com/2009/09/04/mengoptimalkan-koneksi-modem-haier-ce-100-cdma-di-linux/ http://tantos.web.id/blogs/how-to-internet-connection-using-cdma-evdo-modem-and-karmic-koala-ubuntu-9-10 I hope this patch can help other that have the Haier C100 modem, mostly in my country, Indonesia. Signed-off-by: Donny Kurnia <donnykurnia@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: audio gadget: free alsa devices when unloadingCliff Cai
Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: audio gadget: fix wTotalLength calculationCliff Cai
The wTotalLength should contain the sum of the interface and unit descriptor sizes per the Audio Device Class specification 1.0. Reported-by: Sergey Lapin <slapin@ossfans.org> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23usb: otg: isp1301_omap: fix compile errorFelipe Balbi
commit 91c8a5a9985d5bf9c55f6f82f183f57b050b2a3a broke compilation of this driver after it introduced otg_init() as a static inline in <linux/usb/otg.h> Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: musb: workaround Blackfin FIFO anomaliesBryan Wu
Some of these workarounds are already in place, but labeled as affecting all BF52x parts. Since we have official anomaly numbers now, use those defines. And since writing to the FIFO has a similar hang issue as reading from the FIFO, implement the workaround there too when necessary. Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: musb: Fix array index out of bounds issueMaulik Mankad
This patch fixes the below array index out of bounds issue. Buffer overflow, array index of 'aInfo' may be out of bounds. Array 'aInfo' of size 78 may use index value(s) 6..84 The data stored in 'aInfo' array exceeds the array size of 78. This patch increases the size of this array to hold the string correctly without any memory corruption. This issue was reported by Klockwork tool. Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: musb: Fix null pointer dereference issueMaulik Mankad
This patch fixes the following NULL pointer dereference issue. Pointer 'request' returned from call to function 'next_request' at line 748 may be NULL and may be dereferenced at line 792. ============ Code Snippet ============ 748: request = next_request(musb_ep); 785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) { csr &= ~(MUSB_RXCSR_AUTOCLEAR | MUSB_RXCSR_DMAENAB | MUSB_RXCSR_DMAMODE); musb_writew(epio, MUSB_RXCSR, MUSB_RXCSR_P_WZC_BITS | csr); 792: request->actual += musb_ep->dma->actual_len; Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: musb: correct DMA address for txCliff Cai
Since a DMA transfer may need to be kicked off several times to complete, the DMA start must include the length that has already been transferred. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-23USB: musb: gadget_ep0: avoid SetupEnd interruptSergei Shtylyov
Gadget stalling a zero-length SETUP request results in this error message: SetupEnd came in a wrong ep0stage idle In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero- length request. Add the missing '\n' to the error message itself as well... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-10 02:56:31 +0000