| Age | Commit message (Collapse) | Author |
|---|
|
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:
The bus_resume() routine should wake up only the ports that
were suspended by bus_suspend(). Ports that were already
suspended should remain that way.
The interrupt mask is used to detect loss of power in the
bus_resume() routine (if the mask is 0 then power was lost).
However bus_suspend() always sets the mask to 0. Instead the
mask should retain its normal value, with port-change-detect
interrupts disabled if remote wakeup is turned off.
The interrupt mask should be reset to its correct value at the
end of bus_resume() regardless of whether power was lost.
bus_resume() reinitializes the operational registers if power
was lost. However those registers are not in the aux power
well, hence they can lose their values whenever the controller
is put into D3. They should always be reinitialized.
When a port-change interrupt occurs and the root hub is
suspended, the interrupt handler should request a root-hub
resume instead of starting up the controller all by itself.
There's no need for the interrupt handler to request a
root-hub resume every time a suspended port sends a
remote-wakeup request.
The pci_resume() method doesn't need to check for connected
ports when deciding whether or not to reset the controller.
It can make that decision based on whether Vaux power was
maintained.
Even when the controller does not need to be reset,
pci_resume() must undo the effect of pci_suspend() by
re-enabling the interrupt mask.
If power was lost, pci_resume() must not call ehci_run().
At this point the root hub is still supposed to be suspended,
not running. It's enough to rewrite the command register and
set the configured_flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Might speed up some systems. If nothing else, a bad driver should not
take the whole USB subsystem down with it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It's a simple usb-serial driver that just creates a tty device to read
and write from.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is an update for Greg K-H's proposed usbfs2:
http://sourceforge.net/mailarchive/message.php?msg_id=19295229
It creates a dynamic major for USB endpoints and fixes
the endpoint minor calculation.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
there is an error path in the pegasus driver which can leave
the task in TASK_UNINTERRUPTIBLE. Depending on when it
schedules next, this can be bad.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
the latest update for asix.c reverted some endianness fixes. This
reinstates them.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We do already have both the code and a config option, so why not build
this driver? ;-)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Replace kmalloc+memset with kzalloc
Signed-off-by: Yan Burman <yan_952@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Acked-by: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Just digging through code and found these needless variable initializations. So here is the patch.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb_device_match() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove minor double-declaration goof.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
- usb_ftdi_elan_read_pcimem()
- usb_ftdi_elan_write_pcimem()
Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If at some point cypress_init() fails deregister
only the resources that were registered until that point.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them. This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators). This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).
Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog). The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.
Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
EHCI hooks for high speed electrical tests of the root hub ports.
The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0. No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response. Otherwise deferred responses are impossible.
This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Possible memleak fix on error path. The changes:
- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added
Here it goes:
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297. This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1210 ProdID=0003 Rev= 1.00
S: Manufacturer=DigiTech HMG
S: Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signed-off-by: Jaco Kroon <jaco@kroon.co.za>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <-- snip -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...
Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.
Signed-off-by: Naranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level. This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Hello,
- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Hello,
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_free_urb() cleanup
- usb_unlink_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
