aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-08-28p54: fix broadcast buffering in AP modeChristian Lamparter
The patch "mac80211: fix PS-poll response race" somehow broke broadcast buffering in a funny way. During normal operation - stations are awake - the firmware refused to transmit broadcast frames and reported P54_TX_PSM_CANCELLED. But everything worked as soon as one station entered PSM. The reason: The stack sets IEEE80211_TX_CTL_SEND_AFTER_DTIM for outgoing broadcast frames as soon as a station is marked as sleeping. This flag triggers a path which will reroute these frames into p54's "content after beacon" queue, which is designed to cope with the demands for psm. This patch restores the old behavior. IEEE80211_TX_CTL_CLEAR_PS_FILT will once again be used to signalize the firmware to ignore the ps canceling for certain frames. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-26sfc: Improve reliability of RX queue flushingBen Hutchings
Reconfiguring the port requires us to flush all DMA queues. In repeated testing we have found that RX flushes would sometimes fail because the RX DMA engine was not properly isolated from the MACs. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26sfc: Work around XMAC bug causing packet loss with some peersBen Hutchings
Received frames must be re-clocked by the local XGXS to the 156.25 MHz (DDR) clock of the XGMII. If the remote clock is slightly faster this can reduce a minimum IPG of 64 bit-times (1 cycle) to 32 bit-times (half a cycle). If the XMAC detects that a frame has reached the maximum RX frame length in the same cycle that it receives one of these reduced IPGs, it may miss the IPG, causing two valid frames to be treated as a single invalid frame (over-length with bad CRC). We work around this by increasing the maximum RX frame length so that peers with matched MTU will not provoke this bug. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26sfc: QT2025C: Use hard reset onlyBen Hutchings
At probe time, falcon_reset_hw() performs a hard reset of the PHY along with Falcon. There is no need to perform a soft reset later, and any access to standard MDIO registers before the PHY firmware has booted can interrupt the boot process, making the port unusable. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26mdio: Check MDIO_STAT1_FAULT in mdio45_links_ok()Ben Hutchings
Some PHYs will report that the link is up even though there is a fault condition. Therefore, check the fault flag too. We must also read STAT2 to reset this flag. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26sfc: Do not reinitialise XAUI serdes before it has completed resetBen Hutchings
falcon_reset_xaui() waits for XGXS reset to complete, but the XAUI serdes reset may take longer. It needs to check both reset active bits. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26sfc: Fix ordering of device registration and initial netif_carrier_off()Ben Hutchings
We must call netif_carrier_off() after the device is registered, not before, to set the operational state and user-space IFF_RUNNING flag correctly. Since we don't want observers to see an intermediate state, open-code register_netdev() and add efx_update_name() and netif_carrier_off() into the locked region. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26qeth: display "undefined" value of sysfs-attribute "layer2"Ursula Braun
If nothing has been written into the qeth sysfs-attribute layer2, its value is "-1" meaning "not yet defined". But the value is displayed as "1" meaning "layer2 selected". The patch changes the reading of this "-1"-value to "-1" to make clear the layer2-attribute has not yet been defined. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26qeth: display service_level info only when valid.Klaus-Dieter Wacker
qeth displayed an entry in /proc/service_level even when no valid MCL-string was available (the MCL info is blank). The change is to create an entry in /proc/service_level only when MCL-string is non-zero. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26qeth: Cleanup for cast-type determination.Klaus-Dieter Wacker
Clear separation of cast-type determination (send path) for layer-2 resp. layer-3. Allowing to have inline functions for qeth layer- discipline. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26qeth: scheduling while atomic during ifconfig online sequenceFrank Blaschka
In case the IP address list contains entries (not removed when the device was set offline) this entries should be registered next time the device is brought online. In the past this was done implicitly with the device open call but since we wait in the set IPv4 IPA and the device open common code holds various locks this does not work any longer. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26qeth: HiperSockets SIGA retry support on CC=2.Klaus-Dieter Wacker
Qeth HiperSockets support now retries sending of packets when the IBM System z signals a temporary resource shortage (e.g. target buffer full). The packet is enqueued into the device queue. After 3 times of unsuccessful send the packet is dropped. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Update version to 3.100Matt Carlson
This patch updates the tg3 version to 3.100. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26broadcom: Make the 57780 IEEE compliantMatt Carlson
This brings the 57780's phy into IEEE compliance by suppressing the common mode oscillation. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26broadcom: Add AC131 phy supportMatt Carlson
This patch adds support for the AC131 fast ethernet transceiver. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26broadcom: Add BCM50610M supportMatt Carlson
This patch adds support for the BCM50610M phy ID. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Convert code to use PHY_IS_FETMatt Carlson
This patch converts the code to use the PHY_IS_FET flag rather than the ASIC revision to decide whether or not to use FET paths. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Create MII_TG3_FET namespaceMatt Carlson
Broadcom's phys come in two distinctly different register layouts. For the lack of an official term to distinguish between the two formats, we can loosely categorize them by their fast ethernet or gigabit ethernet transceiver description. This patch creates the (driver-internal) Fast Ethernet Transceiver (FET) namespace and converts the 5906 EPHY definitions over. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Tune 5785 clock switchingMatt Carlson
This patch tunes the timeouts the CPMU uses to decide when to switch from the clocks output by the PHY to internal clock sources. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Add 57788, remove 57720Matt Carlson
This patch adds support for the 57788 and removes support for the 57720 which was never released. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Preserve PCIe MPS setting for new devsMatt Carlson
Most older tg3 devices only supported a PCIe maximum payload size of 128 bytes. More recent devices bump this limit up to 256 bytes though. This patch modifies the code so that the MPS limit is only enforced on those devices that only allow the 128 byte setting. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Fix TSO test against wrong flags varMatt Carlson
Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being compared against the wrong flags device member. This patch implements the fix. Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Prevent tx BD corruptionMatt Carlson
This patch prevents a tx BD corruption bug by preventing the device from powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps. The same bits are also used to prevent a system hang during chip reset resulting from a complicated set of events that ultimately leads to PCIe block register corruption. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26tg3: Fix 57780 asic rev PCIe link receiver errorsMatt Carlson
This patch fixes some PCIe link receiver errors by decreasing the internal electrical idle timeout. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26e1000: Remove unused function e1000_mta_set.Graham, David
Remove function e1000_mta_set, as it is no longer called Signed-off-by: Dave Graham <david.graham@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26igb/ixgbe: add IPV6_CSUM support to vlan_featuresAlexander Duyck
We were already exporting TSO6 to the vlan, but we weren't exporting the checksum support for IPV6 which was causing warning messages to be displayed when doing IPv6 TSO over a vlan. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26ixgbe: cleanup functions that should have been defined staticDon Skidmore
We have some ~40 functions that were being called out with 'make namespacecheck'. This patch changes these functions to be static. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26ixgbe: Fix isues while reporting 8259x backplane link capabilitiesMallikarjuna R Chilakala
Fix ethtool get_settings logic to report 10G & 1G advertised and supported link modes in all 8259x 10G backplane connection types except for 82598EB BX network connection type. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26netxen: bridged mode optimizationsNarender Kumar
When the interface is put in bridged mode, destination mac addresses are unknown to firmware. So packets take a slow path (lower priority) in firmware reducing performance. Firmware can cache limited number of remote unicast mac addresses for certain interval, if "dynamic mac learning" mode is enabled. Driver needs to enable this "mac learning" mode in firmware. Currently this is done through net device class sysfs entry, possibly this can also be done upon netlink notifications to from bridge. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26netxen: remove netxen_nic_niu.cDhananjay Phadke
Consolidate all MAC/PHY access functions into netxen_nic_hw.c Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26netxen: implement generic pcie semaphore functionsDhananjay Phadke
Implement common function for locking/unlocking 8 hardware semaphores used for serializing access to shared resouces on a NIC board by different PCI functions. As by definition, callers of these semaphore API can be put to sleep till the semaphore is locked. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26netxen: remove unused codeDhananjay Phadke
Remove code for phy access on unreleased NX2031 based quad-gig board. NX3031 based production quad-gig boards do not require direct phy access by driver. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23Merge branch 'for-next' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan
2009-08-23r6040: bump to version 0.25 and 20 August 2009 release dateFlorian Fainelli
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23r6040: move down second PHY detection to r6040_init_oneMark Kelly
Instead of fully initializing an unusable second r6040 device, perform the PHY detection earlier and bail out in r6040_init_one when we could not read the PHY identifier. Signed-off-by: Mark Kelly <mark@bifferos.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23r6040: remove unused pioaddr variableMark Kelly
This patch removes the unused pioaddr variable. Signed-off-by: Mark Kelly <mark@bifferos.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23netxen: remove netxen_nic_phan_reg.hDhananjay Phadke
Consolidate register definitions in netxen_nic_hdr.h Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23netxen: implement pci driver shutdownAmit Kumar Salecha
Implement pci driver shutdown functionality, this helps quiescing all PCI transaction before chipset is reset. Amit Kumar Salecha <amit@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23netxen: refactor tx dma mapping codeDhananjay Phadke
Move all tx skb mapping code into netxen_map_tx_skb(). Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23netxen: fix firmware reset logicDhananjay Phadke
If netxen_need_fw_reset() return 0 [ implies firmware is up and running], still go through dma mask check, etc. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23netxen: ethtool statistics and control for LRONarender Kumar
Add ethtool -K knob to control LRO in firmware. LRO path is completely separated from GRO, LRO packets are still fed with netif_receive_skb(). Also fix ethtool statistics to include LRO packets. Also use correct message type while configuring interrupt coalescing. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Update version to 2.0.2.Michael Chan
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Use const on flash_table structure.Michael Chan
The structure, once initialized, never changes. Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Refine coalescing parameters.Michael Chan
- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take effect on 5709. - Increase the default rx-frames to reduce interrupt count. - Decrease the default rx-frames-irq and tx-frames-irq to catch more events during NAPI poll. All these will reduce interrupts without affecting latency. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Report FTQ discard counter.Michael Chan
Report this counter to ethtool -S and include it in netstat. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Apply BROKEN_STATS workaround to 5706 and 5708.Michael Chan
Add flag to expand the workaround to both chips. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Close device if MTU change or ring size change fails.Michael Chan
When unable to allocate memory for new MTU or new ring size, we need to close the device to prevent it from crashing. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Check if_running() before touching chip registers.Michael Chan
Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to prevent bus lockups on some systems when the chip is in low power state. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22bnx2: Zero out status block before chip reset.Michael Chan
In case IRQs are shared, we will not mistakenly start processing the ring based on old status block indices. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-21Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 17:10:27 +0000