aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-08-29tg3: Move the JUMBO_CAPABLE and SUPPORT_MSI flagsMatt Carlson
This patch moves where the jumbo capable and msi support flags are located. This is prep work for the addition of msix support flags. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29tg3: Break out mini producer ring handlingMatt Carlson
This patch separates the code that sets up the mini producer ring from the code that sets up the jumbo producer rings. The 5717 asic rev devices do not have a mini ring, but do have a jumbo frame implementation similar to the 5704 and previous devices. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29tg3: Reformat NVRAM case statementsMatt Carlson
This patch fixes up the NVRAM detection switch statements to conform to the kernel coding style. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29tg3: Add new 5785 10/100 only device IDMatt Carlson
This patch adds a new device ID for those 5785 devices that will only use 10/100 phys. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29tg3: Delay mdio bus init until fw finishesMatt Carlson
The device firmware uses the MDIO bus during early setup. If the driver modifies the MDIO bus configuration while it is in use by the firmware, any number of bad things can happen. This patch delays MDIO setup until after the firmware posts its magic signature, signifying initialization is complete. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29net: sh_eth: add value of ether_link pin in platform_dataYoshihiro Shimoda
The method of ETHER_LINK pin is board dependence. This patch adding paramters are: - no_ether_link : If set to 1, do not use ETHER_LINK - ether_link_active_low : If set to 1, ETHER_LINK is active low. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29TI DaVinci EMAC: delay DaVinci EMAC initializationRajashekhara, Sudhakar
On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI flash which is accessed using MTD interface. This patch delays the initialization of DaVinci EMAC driver by changing module_init to late_initcall. This helps SPI and MTD drivers to get initialized before EMAC thereby enabling EMAC driver to read the MAC address while booting and use it. Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and DA850/OMAP-L138 EVMs. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Reviewed-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29WAN/LMC: Fix type_trans().Krzysztof Halasa
Fix lmc_proto_type() invocation. Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29bnx2: Update firmware to 5.0.0.j3.Michael Chan
- Better small packet receive performance. - Better handling of Flow control on 5709. - Fixed iSCSI TMP ABORT TASK problem. - Added iSCSI TCP timestamp option. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28cnic: Put uio init in separate function.Michael Chan
This will allow the 10G iSCSI code to reuse the function. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28cnic: Put rx/tx ring allocation in separate function.Michael Chan
This will allow the 10G iSCSI code to reuse the function. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Move TX completions from workqueue to NAPI.Ron Mercer
TX completions were running in a workqueue queued by the ISR. This patch moves the processing of TX completions to an existing RSS NAPI context. Now each irq vector runs NAPI for one RSS ring and one or more TX completion rings. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Allow running MSIx with fewer vectors.Ron Mercer
Currently we downshift to MSI/Legacy if we don't get enough vectors for cpu_count RSS rings plus cpu_count TX completion rings. This patch allows running MSIX with the vector count that the platform provides. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28qlge: Get rid of 'default' rx_ring type.Ron Mercer
Currently we have three types of RX rings. 1) Default ring - services rx_ring for broadcast/multicast, handles firmware events, and errors. 2) TX completion ring - handles only outbound completions. 3) RSS ring - handles only inbound completions. This patch gets rid of the default ring type and moves it's functionality into the first RSS ring. This makes better use of MSIX vectors since they are a limited resource on some platforms. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-08-28bonding: Have bond_check_dev_link examine netif_runningPetri Gynther
bonding: Have bond_check_dev_link examine netif_running Some network devices do not call netif_carrier_off when they are set administratively down. Have the bonding link check function also inspect the netif_running state. Ignore netif_running if the bond_check_dev_link function is called with "reporting" set, as in that case it's inspecting the capabilities of the non-netif_carrier device driver. Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28bonding: Fix useless test: int > INT_MAXNicolas de Pesloüan
max_bonds is of type int and cannot be greater than INT_MAX. Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28bonding: use compare_ether_addrStephen Hemminger
Bonding can use compare_ether_addr() in bond_release. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28bonding: propogate vlan_features to bonding masterJay Vosburgh
Propogate the vlan_features of the slave devices to the bonding master device, using the same logic as for regular features. Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed the debug logic from the original test patch. Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28libertas: add NULL check on return value of get_zeroed_pageKiran Divekar
Most of the places in debugfs.c are missing a NULL check on the return value of get_zeroed_page API call. Added required NULL check at appropriate places. Signed-off-by: Kiran Divekar <kirandivekar@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: use cfg80211_wext_handlerJussi Kivilinna
Now that cfg80211 functions are added and wext converted to use wext-compat functions, remove wext structures and disabled code. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: disable IWEVPMKIDCAND wireless eventJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: convert mic failure wireless event to cfg80211Jussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: remove unneeded SIOCSIWCOMMITJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: rename wireless stats worker to device pollerJussi Kivilinna
Stats worker no longer poll stats from device anymore. It's still needed to poll device control channel for connect/disconnect events, so rename stats worker as device poller. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: add cfg80211 dump_stationJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: add cfg80211 get_stationJussi Kivilinna
Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats to cfg80211. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: add cfg80211 key handlingJussi Kivilinna
Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: add cfg80211 set_channelJussi Kivilinna
Add cfg80211 set_channel and convert wext to use it. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: add cfg80211 connect, disconnect, join_ibss and leave_ibssJussi Kivilinna
Add cfg80211 connect functions for station and ad-hoc modes and convert wext to use theim. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: enable infrastructure before setting random essidJussi Kivilinna
Random essid must be set to turn on radio when not connected. If device is in ad-hoc mode, this results 'media connect' indications with the random essid which should be ignored. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: set ieee80211_ptr->iftype in rndis_change_virtual_intfJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: use is_zero_ether_addr() and is_broadcast_ether_addr()Jussi Kivilinna
Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of memcmp against ffff_bssid/zero_bssid. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: move link up/down work to separate functionsJussi Kivilinna
Move link up/down work to separate functions and use local array for allocating memory for info structure instead of kzmalloc. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: increase scan timer delayJussi Kivilinna
Increase scan delay from 1 sec to 6 sec. Spec says that scan by OID_802_11_BSSID_LIST_SCAN completes in 6 seconds. Before rfkill patch too short delay was not problem as device was always active (radio on) and performing background scanning. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: resize bssid list if too smallJussi Kivilinna
Buffer used for bssid list might be too small. Change rndis_query_oid() to return required buffer length to caller and make rndis_check_bssid_list() resize buffer when needed. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: get bssid scan list before new scanJussi Kivilinna
OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve current bssid list from device before issuing new scan. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rndis_wlan: ignore OID_802_11_ADD_KEY triggered media connect indicationsJussi Kivilinna
Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger instant media connect indication. These indications are extranous and should be ignored, as otherwise driver would send reassociation event to userspace which in this case is not needed. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28b43: Implement antenna diversity support for LP-PHYGábor Stefanik
The A/G-PHY changes are fallout fixes from the enum change, which in turn allows the LP-PHY code to be much simpler. The antenna_to_phyctl change is a fix for a potential existing bug that this patch may otherwise trigger. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28b43: Enable LP-PHY support by default and remove Kconfig warningGábor Stefanik
The most common LP-PHY device, BCM4312, is now fully functional. So, no need to say "probably won't work for you" anymore. It's also not "for debuggers and developers only", as it is perfectly usable for end-users now (at least for BCM4312). Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28ath5k: don't use PCI ID to find the chip revisionPavel Roskin
AR5K_SREV is available even if the chip has been put to sleep. Relying on the chip register allows binding non-standard PCI IDs by echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id without having to specify the driver data as well. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28ath5k: fix uninitialized value use in ath5k_eeprom_read_turbo_modes()Pavel Roskin
The `val' variable in ath5k_eeprom_read_turbo_modes() is used uninitialized. gcc 4.4.1 with -fno-inline-functions-called-once reports it: eeprom.c: In function 'ath5k_eeprom_read_turbo_modes': eeprom.c:441: warning: 'val' may be used uninitialized in this function Comparing the code to the Atheros HAL, it's clear that the split between ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was incorrect. The Atheros HAL reads both turbo and non-turbo data from EEPROM in one function. Some turbo mode parameters are derived from the same EEPROM values as non-turbo parameters, just from different bits. Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to fix the warning. The actual values and offsets have been cross-checked against Atheros HAL. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28ath5k: clarify srev comparison for CCMP checkBob Copeland
As Pavel Roskin noted, the check for mac version as copied from legacy_hal made no sense. This replaces it with the equivalent and makes up a suitable #define for the mac version legacy_hal checked. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28b43: LP-PHY: Revert to the original PHY register write routineGábor Stefanik
After some discussion on IRC about the PHY register write change, I am not sure anymore if this is the right thing to do. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28iwlwifi: fix ICT irq table endiannessJohannes Berg
The ICT IRQ table is a set of __le32 values, not u32 values, so when reading it we need to take into account that it has to be converted to CPU endianness. This was causing a lot of trouble on my powerpc box where various things would simply not work for no apparent reason with 5xxx cards, but worked with 4965 -- which doesn't use the ICT table. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rt2x00: Cleanup rt2x00mac_bss_info_changed()Ivo van Doorn
Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the variable delayed wasn't used anymore. This means it can be removed along with the call to schedule_work which depended on that variable. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28ssb: Implement PMU LDO control and use it in b43Gábor Stefanik
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable" functions, and use them during LP-PHY baseband init in b43. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28b43: Fix and update LP-PHY codeGábor Stefanik
-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*) in the channel tune routines. -Fix some typos & spec errors found by MMIO tracing. -Optimize b43_phy_write & b43_phy_mask/set/maskset to use only the minimal number of MMIO accesses. (Write is possible using a single 32-bit MMIO write, while set/mask/maskset can be done in 3 16-bit MMIOs). -Set the default channel back to 1, as the bug forcing us to use channel 7 is now fixed. With this, the device comes up, scans, associates, transmits, receives, monitors and injects on all channels - in other words, it's fully functional. Sensitivity and TX power are still sub-optimal, due to the lack of calibration (that's next on my list). Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28b43: LP-PHY: Fix and simplify Qdiv roundupGábor Stefanik
The Qdiv roundup routine is essentially a fixed-point division algorithm, using only integer math. However, the version in the specs had a major error that has been recently fixed (a missing quotient++). Replace Qdiv roundup with a rewritten, simplified version. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28rtl8187: Implement rfkill supportHerton Ronaldo Krzesinski
This change implements rfkill support for RTL8187B and RTL8187L devices, using new cfg80211 rfkill API. Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>