Age | Commit message (Collapse) | Author |
|
The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.
So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Some Logitech mice react to the magic knock like Elantech touchpad would.
This leads to those mice being misdetected as Elantech touchpads. Add a
version query to elantech_detect() to distinguish the two.
[dtor@mail.ru:
- lower severity of some messages - when we are not sure yet if
device is Elantech or not not responding to knock is not an error.
]
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
When resuming from suspend newer Synaptics touchpads do not recover
correctly. Analysis of the resume sequence as applied in Linux was
compared to that of other operating systems. This indicated that the
other OSs were resetting the mouse before attempting to detect it (for
all Synaptics touchpads, old and new). Applying this same modification
fixes these newer Synaptics touchpads and brings the driver into line
with common OS reset behaviour.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Commit ec42d4481e36cbdb5b2801f957e678211a9e5ae2 broke usbtouchscreen for
some eGalax/EETI devices that claim to be HID, but are not.
Devices confirmed to be real HID have the class set to HID and the protocol
set to 'mouse'. Some have HID class but protocol set to 'none'. Those are
not HID and should be driven by usbtouchscreen.
Fix the device ignoring macro by adding match for the protocol too.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: w35und: fix usb_control_msg() error handling in wb35_probe()
Staging: w35und: fix registration with wlan stack
Staging: panel: fix oops on panel_cleanup_module
Staging: rtl8187se: Fix oops and memory poison caused by builtin ieee80211.
Staging: rtl8187se: fix Kconfig dependencies
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: musb: fix srp sysfs entry deletion
USB: musb: resume suspended root hub on disconnect
USB: musb: use right poll limit for low speed devices
USB: musb: be careful with 64K+ transfer lengths, host side
USB: musb: fix data toggle saving with shared FIFO
USB: musb: host endpoint_disable() oops fixes
USB: musb: fix urb_dequeue() method
USB: musb: fix musb_host_tx() for shared endpoint FIFO
USB: musb: be careful with 64K+ transfer lengths (gadget side)
usb: musb: make Davinci *work* in mainline
USB: usb_get_string should check the descriptor type
USB: gadget: fix build error in omap_apollon_2420_defconfig
USB: g_file_storage: automatically disable stalls under Atmel
USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
USB: Quirk for Hummingbird huc56s / Conexant ACM modem
USB: serial: add support for second revision of Ericsson F3507G WWAN card
USB: cdc-acm: add usb id for motomagx phones
USB: option: add BenQ 3g modem information
usb: gadget: obex: select correct ep descriptors
USB: EHCI: slow down ITD reuse
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: ap325rxa: Revert ov772x support.
serial: sh-sci: fix overrun error handling for SH7785 SCIF.
sh: Storage class should be before const qualifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (10696): Remove outdated README for the flexcop-driver
V4L/DVB (10695): Update Technisat card documentation
V4L/DVB (10694): [PATCH] software IRQ watchdog for Flexcop B2C2 DVB PCI cards
V4L/DVB (10663): soc-camera: fix S_CROP breakage on PXA and SuperH
V4L/DVB (10659): em28xx: register device to soundcard for sysfs
|
|
Future iLO devices will have an HP vendor id.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read. The validcrc flag should be cleared after a write so
that the new value can be read.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP. But "rmmod musb_hdrc" didn't
remove that attribute; fix.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.
Easily seen when a hub is connected with no device attached to it;
it will autosuspend. When the hub is disconnected, it still shows
up in /proc/bus/usb/devices
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.
Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO. This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The musb_h_disable() routine can oops in some cases:
- It's not safe to read hep->hcpriv outside musb->lock,
since it gets changed on completion IRQ paths.
- The list iterators aren't safe to use in that way;
just remove the first element while !list_empty(),
so deletions on other code paths can't make trouble.
We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.
[ dbrownell@users.sourceforge.net: massively simplify
patch description; add key points as code comments ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.
[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
===================================================================
|
|
In apollon case, it only used udc, so udc configuration should select
USB_OTG_UTILS also.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter. Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: Mike Lampard <mike@mtgambier.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Adam J. Richter <adam_richter2004@yahoo.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch addes the BenQ 3g modem support to the option driver.
From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We where selecting wrong ep descriptors causing
some troubles while sending files over obex interface.
The problem was a typo while usb_find_endpoint() was being
called for HS endpoints.
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state. This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.
This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.
This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.
[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: Philippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: Federico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If successful, the usb_control_msg() function returns the number of
bytes transferred. Fix up wb35_probe() to only bail out if the function returns
a negative number. Also, fix up ieee80211_alloc_hw() error code to ENOMEM;
otherwise GCC complains that err might be undefined (and is right about that).
Acked-by: Pavel Machek <pavel@suse.cz>
Reported-and-tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Initialize few more fields in wireless device structure so that
wireless core actually accepts our registration.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Check for null pardevice (not registered, ej: panel never attached,
inexistent parport, etc. ) before calling parport_release,
parport_unregister_device, and related funcs on module release.
Signed-off-by: Costantino Leandro <lcostantino@gmail.com>
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
when modprobe and removing rtl8187se ( just for testing, i do not have
that card , and oops and a memory poison error happens on the builtin
ieee80211 of that driver. I dont know if they will port it to the
current ieeee80221 instead of the builtin ones, but just in case i
attach a proposed fix for that problem.
- Change for loop on ieee80211_crypto_deinit for list_for_each_safe to
remove items. Is there an spinlock needed here?
- Call ieee80211_crypto_deinit after exiting all registerd crypto protocols.
Signed-off-by: Costantino Leandro <lcostantino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
rtl8187se uses wireless extensions so it needs to depend on
WIRELESS_EXT (or select it).
rtl8187se uses fields in struct net_device that are only present
if CONFIG_COMPAT_NET_DEV_OPS=y, so it needs to depend on
that symbol also.
drivers/staging/rtl8187se/r8180_core.c:5973: error: 'struct net_device' has no member named 'wireless_handlers'
drivers/staging/rtl8187se/r8180_core.c:5982: error: 'struct net_device' has no member named 'wireless_handlers'
drivers/staging/rtl8187se/r8180_core.c:201: error: 'struct net_device' has no member named 'stop'
drivers/staging/rtl8187se/r8180_core.c:4584: error: 'struct net_device' has no member named 'get_stats'
drivers/staging/rtl8187se/r8180_core.c:5969: error: 'struct net_device' has no member named 'open'
drivers/staging/rtl8187se/r8180_core.c:5970: error: 'struct net_device' has no member named 'stop'
drivers/staging/rtl8187se/r8180_core.c:5972: error: 'struct net_device' has no member named 'tx_timeout'
drivers/staging/rtl8187se/r8180_core.c:5974: error: 'struct net_device' has no member named 'do_ioctl'
drivers/staging/rtl8187se/r8180_core.c:5975: error: 'struct net_device' has no member named 'set_multicast_list'
drivers/staging/rtl8187se/r8180_core.c:5976: error: 'struct net_device' has no member named 'set_mac_address'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a wrong check on num_txbdfree. It could lead to
num_txbdfree become nagative. Result was that the gianfar stops
sending data.
Changes from first version :
- removed a space between parens (David Millers comment)
- full email address in signed off line
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
set on the next initialization (without a reboot inbetween).
This causes breakage on the second initialization due to code that
checks this bit (ssb_device_is_enabled() checks).
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.
This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hp-plus needs to call __alloc_eip_netdev() instead of
__alloc_ei_netdev() since it is linked with 8390p.o.
Fixes this build error:
ERROR: "__alloc_ei_netdev" [drivers/net/hp-plus.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.
There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.
This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.
This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Recent format-negotiation patches caused S_CROP breakage in pxa_camera.c
and sh_mobile_ceu_camera.c drivers, fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As explained in "Writing an ALSA driver" (T. Iwai), audio drivers should
set the struct device for the card before registering the card instance.
This will add the correct /sys/class/sound/cardN/device symlink, so HAL
can see the device and ConsoleKit sets its ACL permissions for the
logged-in user.
For em28xx audio capture cards found e.g. in Hauppauge WinTV-HVR-900 (R2),
this patch fixes errors like:
ALSA lib pcm_hw.c:1429:(_snd_pcm_hw_open) Invalid value for card
Error opening audio: Permission denied
when running mplayer as a normal user.
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* git://git.infradead.org/mtd-2.6:
[MTD] [MAPS] Remove MODULE_DEVICE_TABLE() from ck804rom driver.
[JFFS2] fix mount crash caused by removed nodes
[JFFS2] force the jffs2 GC daemon to behave a bit better
[MTD] [MAPS] blackfin async requires complex mappings
[MTD] [MAPS] blackfin: fix memory leak in error path
[MTD] [MAPS] physmap: fix wrong free and del_mtd_{partition,device}
[MTD] slram: Handle negative devlength correctly
[MTD] map_rom has NULL erase pointer
[MTD] [LPDDR] qinfo_probe depends on lpddr
|