aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2007-08-15IB/mlx4: Incorrect semicolon after if statementIlpo Järvinen
A stray semicolon makes us inadvertently ignore the value of err. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-08-15libata: adjust libata to ignore errors after spinupRyan Power
Adjust libata to ignore errors after spinup This patch is to ignore errors from the spinup attempt if the drive is in the "standby id" state. Signed-off-by: Ryan Power <rpower@sysreset.com> Acked-by: Mark Lord <liml@rtr.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15ata_piix: add TECRA M7 to broken suspend listTejun Heo
Add TECRA M7 to broken suspend list. Reported by Marie Koreen. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Marie Koreen <kbug@koreen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15pata_hpt{37x|3x2n}: fix clock reporting (take 2)Sergei Shtylyov
Fix several inconsistencies in these drivers WRT reporting the clocks: - when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the PCI clock -- make it properly report both clocks and add the same ability to the 'pata_hpt3x2n' driver; - both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the messages -- make them use only the former one; - the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-) Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15pata_hpt37x: actually clock HPT374 with 50 MHz DPLL (take 2)Sergei Shtylyov
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask including mode 5 used to check for the necessity of 66 MHz clocking -- this caused 66 MHz clock to be used for HPT374 chip that does not tolerate it. While fixing this, also remove PLL mode from the TODO list -- I don't think it's still a relevant item. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15pata_artop: fix UDMA5 for AEC6280[R] and UDMA6 for AEC6880[R]Bartlomiej Zolnierkiewicz
Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4) and for AEC6880[R] it is UDMA6 (not UDMA5): * Fix the problem by adding missing struct ata_port_info to artop_init_one(). * Use the right naming (s/626/628/). * Bump driver version. Fixes IDE->libata regression, problem was never present in IDE aec62xx driver. Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15ata_piix: update map 10b for ich8mTejun Heo
Fix map entry 10b for ich8. It's [P0 P2 IDE IDE] like ich6 / ich6m. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: <Kristen Carlson Accardi> kristen.c.accardi@intel.com Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15sata_mv: PCI IDs for Hightpoint RocketRaid 1740/1742Alan Cox
Underneath all the HPT packaging, PCI identifiers, binary driver modules and stuff you find that ... Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-15[libata] pata_isapnp: replace missing module device tableJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14[IOAT]: Remove redundant struct member to avoid descriptor cache missShannon Nelson
The layout for struct ioat_desc_sw is non-optimal and causes an extra cache hit for every descriptor processed. By tightening up the struct layout and removing one item, we pull in the fields that get used in the speedpath and get a little better performance. Before: ------- struct ioat_desc_sw { struct ioat_dma_descriptor * hw; /* 0 8 */ struct list_head node; /* 8 16 */ int tx_cnt; /* 24 4 */ /* XXX 4 bytes hole, try to pack */ dma_addr_t src; /* 32 8 */ __u32 src_len; /* 40 4 */ /* XXX 4 bytes hole, try to pack */ dma_addr_t dst; /* 48 8 */ __u32 dst_len; /* 56 4 */ /* XXX 4 bytes hole, try to pack */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dma_async_tx_descriptor async_tx; /* 64 144 */ /* --- cacheline 3 boundary (192 bytes) was 16 bytes ago --- */ /* size: 208, cachelines: 4 */ /* sum members: 196, holes: 3, sum holes: 12 */ /* last cacheline: 16 bytes */ }; /* definitions: 1 */ After: ------ struct ioat_desc_sw { struct ioat_dma_descriptor * hw; /* 0 8 */ struct list_head node; /* 8 16 */ int tx_cnt; /* 24 4 */ __u32 len; /* 28 4 */ dma_addr_t src; /* 32 8 */ dma_addr_t dst; /* 40 8 */ struct dma_async_tx_descriptor async_tx; /* 48 144 */ /* --- cacheline 3 boundary (192 bytes) --- */ /* size: 192, cachelines: 3 */ }; /* definitions: 1 */ Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-14Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: i2c-s3c2410: Build fix i2c/menelaus: Build fix i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang i2c-mpc: Don't disable I2C module on stop condition i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class i2c/isp1301_omap: Build fixes, whitespace i2c-mpc: Pass correct dev_id to free_irq on error path i2c-i801: Typo: erroneous
2007-08-14i2c-s3c2410: Build fixBen Dooks
Fixup the include files after the arch moves that where included in 2.6.23. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c/menelaus: Build fixDavid Brownell
Fix Menelaus build error, and remove needless "#define DEBUG". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c-mv64xxx: Reinitialize hw and driver on I2C bus hangDale Farnsworth
Under certain conditions, the mv64xxx I2C bus can hang preventing further operation. To make the driver more robust, we now reset the I2C hardware and the driver state machine when such hangs are detected. Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Acked-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c-mpc: Don't disable I2C module on stop conditionDomen Puncer
Disabling module on stop doesn't work on some CPUs (ie. mpc8241, as reported by Guennadi Liakhovetski), so remove that. Disable I2C module on errors/interrupts to prevent it from locking up on mpc5200b. Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c-iop3xx: Set I2C_CLASS_HWMON to adapter classArnaud Patard
In order to be able to use sensors on the IOP3xx SoCs, one needs to set the adapter class to I2C_CLASS_HWMON. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c/isp1301_omap: Build fixes, whitespaceDavid Brownell
Build fixes for isp1301_omap driver. I think an earlier version of this must have gotten lost somewhere, or maybe it only went into the Linux-OMAP tree. Also, some whitespace fixes to bring this more into sync with the version of this found in the Linux-OMAP tree. (That version has updates for the OTG controller on the OMAP 1710 which break that functionality on OMAP 161x boards like the H2, so merging all of it is not currently an option.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c-mpc: Pass correct dev_id to free_irq on error pathScott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14i2c-i801: Typo: erroneousJean Delvare
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-14Merge branch 'master' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [IPVS]: Use IP_VS_WAIT_WHILE when encessary. [NET]: Share correct feature code between bridging and bonding [ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc [IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc [WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc [DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm() [DCCP]: fix theoretical ccids_{read,write}_lock() race [XFRM]: Clean up duplicate includes in net/xfrm/ [TIPC]: Clean up duplicate includes in net/tipc/ [SUNRPC]: Clean up duplicate includes in net/sunrpc/ [PKT_SCHED]: Clean up duplicate includes in net/sched/ [IPV6]: Clean up duplicate includes in net/ipv6/ [IPV4]: Clean up duplicate includes in net/ipv4/ [ATM]: Clean up duplicate includes in net/atm/ [ATM]: Clean up duplicate includes in drivers/atm/ [IPCONFIG]: ip_auto_config fix [ATM]: fore200e_param_bs_queue() must be __devinit
2007-08-14Merge branch 'upstream-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: e1000: Add device IDs of new 82571 board variants xen-netfront: Avoid deref'ing skbafter it is potentially freed. 3c59x maintainer 3c59x: fix duplex configuration natsemi: fix netdev error acounting ax88796 printk fixes myri10ge: Use the pause counter to avoid a needless device reset via-rhine: disable rx_copybreak on archs that don't allow unaligned DMA access
2007-08-14e1000: Add device IDs of new 82571 board variantsAuke Kok
This patch adds support for 2 new board variants: - A Quad port fiber 82571 board - A blade version of the 82571 quad copper board Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-13[NET]: Share correct feature code between bridging and bondingHerbert Xu
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the bonding driver may produce bogus combinations of the checksum flags and SG/TSO. For example, if you bond devices with NETIF_F_HW_CSUM and NETIF_F_IP_CSUM you'll end up with a bonding device that has neither flag set. If both have TSO then this produces an illegal combination. The bridge device on the other hand has the correct code to deal with this. In fact, the same code can be used for both. So this patch moves that logic into net/core/dev.c and uses it for both bonding and bridging. In the process I've made small adjustments such as only setting GSO_ROBUST if at least one constituent device supports it. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-13[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzallocMariusz Kozlowski
drivers/atm/iphase.c | 111508 -> 111431 (-77 bytes) drivers/atm/iphase.o | 254740 -> 254260 (-480 bytes) Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-13[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]allocMariusz Kozlowski
drivers/net/irda/irda-usb.c | 59694 -> 59541 (-153 bytes) drivers/net/irda/irda-usb.o | 170588 -> 169256 (-1332 bytes) Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-13[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzallocMariusz Kozlowski
drivers/net/wan/hdlc_fr.c | 31260 -> 31223 (-37 bytes) drivers/net/wan/hdlc_fr.o | 144872 -> 144728 (-144 bytes) Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2007-08-13[ATM]: Clean up duplicate includes in drivers/atm/Jesper Juhl
This patch cleans up duplicate includes in drivers/atm/ Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-13[ATM]: fore200e_param_bs_queue() must be __devinitAdrian Bunk
WARNING: drivers/built-in.o(.text+0x6203bb): Section mismatch: reference to .init.text:fore200e_param_bs_queue (between 'fore200e_initialize' and 'fore200e_monitor_putc') Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-14xen-netfront: Avoid deref'ing skbafter it is potentially freed.Jeremy Fitzhardinge
xennet_tx_bug_gc can free the skb before we use it, so make sure we don't. Signed-off-by: Keir Fraser <keir@xensource.com> Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-143c59x: fix duplex configurationSteffen Klassert
A special sequence of ifconfig up/down and plug/unplug the cable can break the duplex configuration of the driver. Setting vp->mii.full_duplex = vp->full_duplex in vortex_up should fix this. Addresses Bug 8575 3c59x duplex configuration broken http://bugzilla.kernel.org/show_bug.cgi?id=8575 Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org> Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de> Cc: Natalie Protasevich <protasnb@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14natsemi: fix netdev error acountingAndrew Morton
When a detailed netdev error is counted, we also must account for it in the aggregated error count. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106 Cc: Tim Hockin <thockin@hockin.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Chongfeng Hu <loveminix@yahoo.com.cn> Cc: Natalie Protasevich <protasnb@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14ax88796 printk fixesAndrew Morton
drivers/net/ax88796.c: In function `ax_probe': drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4) drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5) resource_size_t isn't size_t. Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14myri10ge: Use the pause counter to avoid a needless device resetBrice Goglin
Use the pause counter to avoid a needless device reset, and print a message telling the admin that our link partner is flow controlling us down to 0 pkts/sec. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14via-rhine: disable rx_copybreak on archs that don't allow unaligned DMA accessDustin Marquess
Patch to disable the rx_copybreak feature on hardware architectures that don't allow unaligned DMA access. #ifdef code taken from tulip_core.c. Problem pointed out by Ivan Kokshaysky. Signed-off-by: Dustin Marquess <jailbird@alcatraz.fdf.net> Cc: Francois Romieu <romieu@fr.zoreil.com> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14ACPI: EC: Fix "no battery" regressionAlexey Starikovskiy
Restore deleted call to register query methods. http://bugzilla.kernel.org/show_bug.cgi?id=8886 Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
2007-08-13mlx4_core: Wait 1 second after reset before accessing deviceEli Cohen
Put a 1000 msec delay after resetting the device before attempting to do config cycles on it. Not waiting causes system hangs on some chipsets, e.g. Intel E7520, when the driver is loaded. Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-08-12hwmon: (smsc47m1) restore missing name attributeJean Delvare
The smsc47m1 driver no longer creates the name attribute used by libsensors to identify chip types. It was lost during the conversion to a platform driver. I was fooled by the fact that we do have a group with all attributes, but only to delete them all at once. The group is not used to create the attributes, so we have to explicitly create the name attribute. This fixes lm-sensors ticket #2236: http://lm-sensors.org/ticket/2236 Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-08-12hwmon: (w83627ehf) don't assume bank 0Jean Delvare
Don't assume that the default bank is 0. For one thing, we don't even set it to 0 when the driver is loaded, so the initial state might be different. For another, something (say, the BIOS) might access the chip and leave with the bank set to something different, so assuming that the bank value is 0 is not safe. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-08-12hwmon: (w83627ehf) read fan_div values during probeMark M. Hoffman
This patch forces the driver to read the fan divider values during early init. Otherwise, a call to store_fan_min() could access uninitialized variables. Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-08-12Pull sbs into release branchLen Brown
2007-08-12Pull processor into release branchLen Brown
2007-08-12Pull fluff into release branchLen Brown
2007-08-12Pull ec into release branchLen Brown
2007-08-12Pull dock-bay into release branchLen Brown
2007-08-12Pull bugzilla-8842 into release branchLen Brown
2007-08-12Pull bugzilla-8768 into release branchLen Brown
2007-08-12Pull bugzilla-3774 into release branchLen Brown
2007-08-12pull asus sony thinkpad into release branchLen Brown
2007-08-12ACPI: thermal: add DMI hooks to handle AOpen's broken Award BIOSLen Brown
Use DMI to: 1. enable polling (BIOS thermal events are broken) 2. disable active trip points (BIOS fan control is broken) 3. disable passive trip point (BIOS hard-codes it too low) The actual temperature reading does work, and with the aid of polling, the critical trip point should work too. http://bugzilla.kernel.org/show_bug.cgi?id=8842 Signed-off-by: Len Brown <len.brown@intel.com>
2007-08-12ACPI: thermal: create "thermal.act=" to disable or override active trip pointLen Brown
thermal.act=-1 disables all active trip points in all ACPI thermal zones. thermal.act=C, where C > 0, overrides all lowest temperature active trip points in all thermal zones to C degrees Celsius. Raising this trip-point may allow you to keep your system silent up to a higher temperature. However, it will not allow you to raise the lowest temperature trip point above the next higher trip point (if there is one). Lowering this trip point may kick in the fan sooner. Note that overriding this trip-point will disable any BIOS attempts to implement hysteresis around the lowest temperature trip point. This may result in the fan starting and stopping frequently if temperature frequently crosses C. WARNING: raising trip points above the manufacturer's defaults may cause the system to run at higher temperature and shorten its life. Signed-off-by: Len Brown <len.brown@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-05 18:00:58 +0000