| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-gd: re-get capacity on revalidate
tx4938ide: Avoid underflow on calculation of a wait cycle
tx4938ide: Do not call devm_ioremap for whole 128KB
tx4938ide: Check minimum cycle time and SHWT range (v2)
ide: Switch to a common address
ide-cd: fix DMA alignment regression
|
|
We need to re-get a removable media's capacity when revalidating the
disk so that its partitions get rescanned by the block layer.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: axboe@kernel.dk
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Make 'wt' variable signed while it can be negative during calculation.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Call devm_ioremap() for CS0 and CS1 separetely.
And some style cleanups.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
SHWT value is used as address valid to -CSx assertion and -CSx to -DIOx
assertion setup time, and contrarywise, -DIOx to -CSx release and -CSx
release to address invalid hold time, so it actualy applies 4 times and
so constitutes -DIOx recovery time. Check requirement of the recovery
time and cycle time. Also check SHWT maximum value.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
e5318b531b008c79d2a0c0df06a7b8628da38e2f ("ide: use the dma safe check for
REQ_TYPE_ATA_PC") introduced a regression which caused some ATAPI drives to
turn off DMA for REQ_TYPE_BLOCK_PC commands while burning and thus degrading
performance and ultimately causing an excessive amount of underruns.
The issue is documented also in:
http://bugzilla.kernel.org/show_bug.cgi?id=11742.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
[bart: fixup patch description per comments from Sergei Shtylyov]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cirrusfb_zorro_unmap() may be called both from __devexit and (on
cleanup path) from __devinit. So it needs to be a normal function,
same as for cirrusfb_pci_unmap()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'cris_move' of git://www.jni.nu/cris:
[CRIS] Move header files from include to arch/cris/include.
[CRISv32] Remove warning in io.h
|
|
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/leds/leds-hp-disk.c
drivers/misc/panasonic-laptop.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (21 commits)
sh: fix sh2a cache entry_mask
sh: Enable NFS root in Migo-R defconfig.
sh: FTRACE renamed to FUNCTION_TRACER.
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Define SCSPTR1 for SH 7751R
sh: Add sci_rxd_in of SH4-202
Add support usb setting on sh 7366
sh: Change register name SCSPTR to SCSPTR2
sh: use the new byteorder headers.
sh: SHmedia ISA tuning fixups.
sh: Kill off long-dead HD64465 cchip support.
sh: Revert "SH 7366 needs SCIF_ONLY"
sh: Simplify and lock down the ISA tuning.
sh: sh7785lcr: Select uImage as default image target.
sh: Add on-chip RTC support for SH7722.
SH 7366 needs SCIF_ONLY
gdrom: Fix compile error
sh: Provide a sample defconfig for the UL2 (SH7366) board.
sh: Fix FPU tuning on toolchains with mismatched multilib targets.
sh: oprofile: Fix up the SH7750 performance counter name.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add missing null terminating entry to bq4802_match[].
sparc: use the new byteorder headers
rtc-m48t59: shift zero year to 1968 on sparc (rev 2)
dbri: check dma_alloc_coherent errors
sparc64: remove byteshifting from out* helpers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: add whitelist for devices with known good pata-sata bridges
sata_via: fix support for 5287
libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
ATA: remove excess kernel-doc notation
|
|
Inspired by Sergio Luis' similar patches, I finally found
a case which is trivial enough that spatch won't choke
on it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
SH4-202 doesn't have SCSXX1. But it is treated so that there is SCSPTR1 in
current code. This patch add sci_rxd_in of SH4-202.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This change a name of SCSPTR used in sci_rxd_in of SH5-101.
SCSPTR is not declared and will become the error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
As noticed by Saikiran Madugula, commit 7447ef63cf2dfdc444f4c72ae13f604350b2e25f
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove excess kernel-doc function parameters from networking header
& driver files:
Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Move SKB trim before we lookup the socket so we don't have to
put it on failure.
Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
5287 used to be treated as vt6420 but it didn't work. It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports. This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata. Another controller
which falls into this category is ata_piix w/ SIDPR access.
libata now has facility to deal with this class of controllers named
slave_link. A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.
This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.
This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
In ata_tf_to_lba48(), when evaluating
(tf->hob_lbal & 0xff) << 24
the expression is promoted to signed int (since int can hold all values
of u8). However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.
For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:
ata3.00: HPA detected: current 2930277168, native 18446744072344861488
where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.
Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.
Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Remove excess kernel-doc function parameter notation from drivers/ata/:
Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Currently, the numa_node of OF-devices will be overwritten during
device_register, which simply sets the node to -1. On cell machines,
this means that devices can't find their IOMMU, which is referenced
through the device's numa node.
Set the numa node for OF devices with no parent, and use the
lower-level device_initialize and device_add functions, so that the
node is preserved.
We can remove the call to set_dev_node in of_device_alloc, as it
will be overwritten during register.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Acoording commit aa24886e379d2b641c5117e178b15ce1d5d366ba,
dma_free_coherent() need irqs enabled.
This patch fix following warning messages:
WARNING: at linux/arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0xaa/0xb0()
Call Trace:
[<ffffffff8023f80f>] warn_on_slowpath+0x5f/0x90
[<ffffffff80496ffa>] ? __kfree_skb+0x3a/0xa0
[<ffffffff802a4723>] ? discard_slab+0x23/0x40
[<ffffffff8021274a>] dma_free_coherent+0xaa/0xb0
[<ffffffff8043668f>] amd8111e_close+0x10f/0x1b0
[<ffffffff8049f3ae>] dev_close+0x5e/0xb0
[<ffffffff8049efa1>] dev_change_flags+0xa1/0x1e0
[<ffffffff806b2171>] ic_close_devs+0x36/0x4e
[<ffffffff806b29ee>] ip_auto_config+0x581/0x10f3
[<ffffffff803a6e19>] ? kobject_add+0x69/0x90
[<ffffffff803a698a>] ? kobject_get+0x1a/0x30
[<ffffffff803a785b>] ? kobject_uevent+0xb/0x10
[<ffffffff803a6c62>] ? kset_register+0x52/0x60
[<ffffffff803a6f9b>] ? kset_create_and_add+0x6b/0xa0
[<ffffffff804e2e74>] ? tcp_ca_find+0x24/0x50
[<ffffffff806b246d>] ? ip_auto_config+0x0/0x10f3
[<ffffffff8020903c>] _stext+0x3c/0x150
[<ffffffff802772d3>] ? register_irq_proc+0xd3/0xf0
[<ffffffff802f0000>] ? mb_cache_create+0x80/0x1f0
[<ffffffff80688693>] kernel_init+0x141/0x1b8
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff8020d609>] child_rip+0xa/0x11
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff8020d5ff>] ? child_rip+0x0/0x11
Signed-off-by: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 401c0aabec4b97320f962a0161a846d230a6f7aa introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.
This patch causes the VLAN tag to be stored in its proper location.
Tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:
bond_close()
bond_alb_deinitialize()
tlb_deinitialize()
kfree(bond_info->tx_hashtbl)
bond_info->tx_hashtbl = NULL
Unfortunately if there are still slaves in the bond, when removing the
module the following happens:
bonding_exit()
bond_free_all()
bond_release_all()
bond_alb_deinit_slave()
tlb_clear_slave()
tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
u32 next_index = tx_hash_table[index].next
As you might guess we panic when trying to access a few entries into the
table that no longer exists.
I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine. It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch reworks the resource free logic performed at the time
a bonding device is released. This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.
"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
During the rework of the mii monitor for:
commit f0c76d61779b153dbfb955db3f144c62d02173c2
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
I left out the increment of the link failure counter. This
patch corrects that omission.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: destroy partitions and notify udev when md array is stopped.
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5326/1: AFEB9260: Fix for i2c_board_info structure
[ARM] mx31ads: Add missing include
[ARM] MXC: Fix mxc_gpio_get(), which must read PSR register instead DR.
[ARM] MX3: Use ioremap wrapper to map SoC devices nonshared
[ARM] gpio_free might sleep, arm architecture
[ARM] ep93xx: fix OHCI DMA mask
leds: da903x: (da9030 only) led brightness reversed.
[ARM] sharpsl_pm: fix compilation w/o CONFIG_PM
[ARM] pcm037: map AIPS1 and AIPS2 as nonshared area
[ARM] build fixes for netX serial driver
[ARM] 5323/1: Remove outdated empeg documentation.
[ARM] 5299/1: Add maintainer for Mobilepro 900/c
[ARM] corgi_lcd: fix simultaneous compilation with corgi_bl
[ARM] pxa/spitz: fix spi cs on spitz
[ARM] 5322/1: Fix fastpath issue in mmci.c
[ARM] xsc3: revert writethrough memory-type encoding change
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[PATCH] Switch all my contributions stuff to a single common address
[WATCHDOG] pci: use pci_ioremap_bar() in drivers/watchdog
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
CHAR: Delete old and now unused M48T35 RTC driver for SGI IP27.
CHAR: Delete old and now unused DS1286 driver.
MIPS: Sort out CPU type to name translation.
MIPS: Use the new byteorder headers
MIPS: Probe for watch registers on cores of all vendors, not just MTI.
MIPS: Switch FPU emulator trap to BREAK instruction.
MIPS: SMP: Do not initialize __cpu_number_map/__cpu_logical_map for CPU 0.
MIPS: Consider value of c0_ebase when computing value of exception base.
MIPS: Clean up MIPSxx-optimized bitop functions
MIPS: New feature test macro cpu_has_mips_r
MIPS: RBTX4927: Add GPIO-LED support
MIPS: TXx9: Fix RBTX4939 ethernet address initialization
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
|
