| Age | Commit message (Collapse) | Author |
|---|
|
Simplified the logic in w1_slave_found by using the new
w1_attach_slave_device function to find a slave and mark it as active or
add the device if the crc checks.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sysfs entries were added to manually add and remove slave devices. This
is useful if the automatic bus searching is disabled, and the device ids
are already known.
[akpm@linux-foundation.org: fix printk types]
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added strong pullup to thermal sensor driver and general documentation on
the sensor.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a strong pullup option to the w1 system. This supplies extra power
for parasite powered devices. There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.
The one wire bus requires at a minimum one wire and ground. The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example. The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value. This enables the
strong pullup for supported hardware, which can supply more current when
requested. Unsupported hardware will just delay with the bus high.
The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration. The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.
Switched from simple_strtol to strict_strtol.
Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The w1_process thread's sleeping and termination has been modified.
msleep_interruptible was replaced by schedule_timeout and schedule to
allow for kthread_stop and wake_up_process to interrupt the sleep and the
unbounded sleeping when a bus search is disabled. The W1_MASTER_NEED_EXIT
and flags variable were removed as they were redundant with
kthread_should_stop and kthread_stop. If w1_process is sleeping,
requesting a search will immediately wake it up rather than waiting for
the end of msleep_interruptible previously.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the creation of the w1_process thread to after the device has been
initialized. This way w1_process doesn't have to check to see if it has
been initialized and the bus search can proceed without sleeping. That
also eliminates two checks in the w1_process loop. The sleep now happens
at the end of the loop not the beginning.
Also added a comment for why the atomic_set was 2.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Early abort if the master driver or the hardware goes away in the middle
of a bus search operation. The alternative is to spam the print buffer up
to 64*64 times with read errors in the case of USB.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master. Those routines were moved to the threads that were
previously requesting those operations. A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed. The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen. A problem with registering a family code
was fixed. A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.
The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tpm_register_hardware() leaks devname on an error path.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11425
Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch tpm-correct-tpm-timeouts-to-jiffies-conversion reveals a bug in the
Broadcom BCM0102 TPM chipset used in the Dell Latitude D820 - although
most of the timeouts are returned in usecs as per the spec, one is
apparently returned in msecs, which results in a too-small value leading
to a timeout when the code treats it as usecs. To prevent a regression,
we check for the known too-short value and adjust it to a value that makes
things work.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes timeouts conversion to jiffies, by replacing
msecs_to_jiffies() calls with usecs_to_jiffies(). According to TCG TPM
Specification Version 1.2 Revision 103 (pages 166, 167) TPM timeouts and
durations are returned in microseconds (usec) not in miliseconds (msec).
This fixes a long hang while loading TPM driver, if TPM chip starts in
"Idle" state instead of "Ready" state. Without this patch - 'modprobe'
may hang for 30 seconds or more.
Signed-off-by: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the Thermal messages (temperature got past Tmid) be displayed only
once because:
1) it's the BIOS job to configure and handle the memory throttling
2) if the BIOS is broken or is aware about the condition, flooding the
system logs won't help anything.
3) According to the specification update for Intel 5000 MCHs, all the
revisions of this MCH have problems on the thermal sensors, making
not automatic (a.k.a. intelligent thermal throttling) impossible.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the i5000_edac messages, making everything pass through the EDAC
(so the log controls will work) and being more specific about the errors.
Also, it makes the miscellaneous errors optional and disabled by default.
As I didn't found anywhere information about M23ERR-M26ERR
(FERR_NF_THERMAL) on FERR_NF_FBD, I'm removing them.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for the dual-core MPC8572 processor. We have
to support making SPR changes on each core. Also, since we can
have multiple memory controllers sharing an interrupt, flag the
interrupts with IRQF_SHARED.
Signed-off-by: Andrew Kilkenny <akilkenny@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix 443BX/GX MCH suppport in a EDAC.
It makes i82443bxgx_edac coexist with intel_agp using the same approach as
several other EDAC drivers.
Tested on Intel's L443GX with redhat's 2.6.18 with whole EDAC subsystem
backported a while ago.
[root@host ~]# dmesg|grep -iE '(AGP|EDAC)'
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440GX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
EDAC MC: Ver: 2.1.0 Jun 27 2008
EDAC MC0: Giving out device to 'i82443bxgx_edac' 'I82443BXGX': DEV 0000:00:00.0
EDAC PCI0: Giving out device to module 'i82443bxgx_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
Signed-off-by: Vladislav Bogdanov <slava@nsys.by>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move it into sysrq.c, along with the rest of the sysrq implementation.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The only use is to pass this to le16_to_cpu, declare as such
drivers/char/moxa.c:548:11: warning: cast to restricted __le16.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code scriblles over a local pointer whereas it appears to be trying
to write to the memory at which that pointer points.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11397
Nobody we know can test this change.
Reported-by: Zvonimir Rakamaric <zrakamar@cs.ubc.ca>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ds1286_get_time(); is not called from atomic context, sleep for 20 ms is
better choice than a (home-made) busy waiting for such a situation.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove CVS keywords that weren't updated for a long time from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PnP encodes the resource type directly as its struct resource->flags value
which is an unsigned long. Make it so...
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's no point in printing some ancient version number forever.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam M Belay <abelay@MIT.EDU>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
echo 3 >> /sys/class/graphics/fbcon/rotate_all, then switch to another
console. Result:
BUG: unable to handle kernel paging request at ffffc20005d00000
IP: [bitfill_aligned+149/265] bitfill_aligned+0x95/0x109
PGD 7e228067 PUD 7e229067 PMD 7bc1f067 PTE 0
Oops: 0002 [1] SMP
CPU 1
Modules linked in: [...a lot...]
Pid: 10, comm: events/1 Not tainted 2.6.26.5-45.fc9.x86_64 #1
RIP: 0010:[bitfill_aligned+149/265] [bitfill_aligned+149/265] bitfill_aligned+0x95/0x109
RSP: 0018:ffff81007d811bc8 EFLAGS: 00010216
RAX: ffffc20005d00000 RBX: 0000000000000000 RCX: 0000000000000400
RDX: 0000000000000000 RSI: ffffc20005d00000 RDI: ffffffffffffffff
RBP: ffff81007d811be0 R08: 0000000000000400 R09: 0000000000000040
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000010000
R13: ffffffff811632f0 R14: 0000000000000006 R15: ffff81007cb85400
FS: 0000000000000000(0000) GS:ffff81007e004780(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffc20005d00000 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process events/1 (pid: 10, threadinfo ffff81007d810000, task ffff81007d808000)
Stack: ffff81007c9d75a0 0000000000000000 0000000000000000 ffff81007d811c80
ffffffff81163a61 ffff810000000000 ffffffff8115f9c8 0000001000000000
0000000100aaaaaa 000000007cd0d4a0 fffffd8a00000800 0001000000000000
Call Trace:
[cfb_fillrect+523/798] cfb_fillrect+0x20b/0x31e
[soft_cursor+416/436] ? soft_cursor+0x1a0/0x1b4
[ccw_clear_margins+205/263] ccw_clear_margins+0xcd/0x107
[fbcon_clear_margins+59/61] fbcon_clear_margins+0x3b/0x3d
[fbcon_switch+1291/1466] fbcon_switch+0x50b/0x5ba
[redraw_screen+261/481] redraw_screen+0x105/0x1e1
[ccw_cursor+0/1869] ? ccw_cursor+0x0/0x74d
[complete_change_console+48/190] complete_change_console+0x30/0xbe
[change_console+115/120] change_console+0x73/0x78
[console_callback+0/292] ? console_callback+0x0/0x124
[console_callback+97/292] console_callback+0x61/0x124
[schedule_delayed_work+25/30] ? schedule_delayed_work+0x19/0x1e
[run_workqueue+139/282] run_workqueue+0x8b/0x11a
[worker_thread+221/238] worker_thread+0xdd/0xee
[autoremove_wake_function+0/56] ? autoremove_wake_function+0x0/0x38
[worker_thread+0/238] ? worker_thread+0x0/0xee
[kthread+73/118] kthread+0x49/0x76
[child_rip+10/18] child_rip+0xa/0x12
[kthread+0/118] ? kthread+0x0/0x76
[child_rip+0/18] ? child_rip+0x0/0x12
Because fbcon_set_all_vcs()->FBCON_SWAP() uses display->rotate == 0 instead
of fbcon_ops->rotate, and vc_resize() has no effect because it is called with
new_cols/rows == ->vc_cols/rows.
Tested on 2.6.26.5-45.fc9.x86_64, but
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git seems to
have the same problem.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.26.x, maybe 2.6.25.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add driver for TMIO framebuffer cells as found e.g. in Toshiba TC6393XB
chips.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make alloc_carmine_fb() __devinit.
WARNING: drivers/video/carminefb.o(.text+0x81b): Section mismatch in reference from the function alloc_carmine_fb() to the variable .devinit.data:carminefb_fix
The function alloc_carmine_fb() references the variable __devinitdata
carminefb_fix. This is often because alloc_carmine_fb lacks a
__devinitdata annotation or the annotation of carminefb_fix is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Support the Matrox G200eV chip, based on timings that I found in the X.org
matrox driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Epson s1d13xxx hardware is common in many handhelds, but our driver is
currently locked to a single chip revision. This patch adds an array of
known to work revisions (which can be extended).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Acked-by: Thibaut Varène <varenet@parisc-linux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, it is possible to set a graphics VESA mode at boot time via the
vga= parameter even when no framebuffer driver supporting this is
configured. This could lead to the system booting with a black screen,
without a usable console.
Fix this problem by only allowing to set graphics modes at boot time if a
supporting framebuffer driver is configured.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's no point in checking diff == c->vc_rows, because it can be true
only when count == 0, but we already checked that. Additionally move
variables used only in one block to this block.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Join multiple scr_memcpyw into 1-3 calls (usually 2). (benchmarked
average speedup: 1%)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current EDID parser in the linux kernel ignores interlace modes. The
patch looks for the edid interlace flag and adjusts the vertical
resolution if it is found.
Signed-off-by: Jon Dufresne <jon.dufresne@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some BIOSes return error codes when queried for information about
modes from their own modelist. uvesafb treats this as an error
case and bails out.
Change this behavior so that broken modes do not prevent the driver
from working. Only the failure to retrieve information about any
usable video mode is considered to be an error case.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement support for HW color expansion of 1bpp images, along with some
improvements to the FIFO handling and other accel operations.
The offset fixup code is now unnecessary as the fbcon core will call our
set_par upon switch back from KD_GRAPHICS before anything else happens. I
removed it as it would slow down accel operations.
The fifo wait has been improved to avoid hitting the HW register as often,
and the various accel ops are now performing better caching of register
values.
Overall, this improve accel performances. The imageblit acceleration does
result in a small overall regression in performances on some machines (on
the order of 5% on some x86), probably becaus the SW path provides a
better bus utilisation, but I decided to ingnore that as the performances
is still very good, and on the other hand, some machines such as some
sparc64 get a 3 fold performance improvement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a couple of incomplete tests of the chip families in the engine
init/reset code and proper initialization of the destination cache mode.
The result should better match what the latest X radeon driver does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove imacfb entirely, merging its DMI table into the (otherwise very
similar) efifb driver. This also adds hardware support for many of the
newer Intel Apple hardware. This has been fairly well tested; we've been
shipping it in Fedora for some time.
Signed-off-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
can handle
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A memory clock value (MCLK) is changed to a minimum required by a current
mode bandwidth. This usually lowers the MCLK to its minimum (50 MHz) thus
decreasing the card performance. Just leave the MCLK value set by card
BIOS.
The CL-GD5446 Technical Reference Manual point 9.9.1.3 states that if a
pixclock value is close (~1%) to the MCLK or MCLK/2 this may result in a
jitter on the screen. A countermeasure is to use the MCLK as pixclock
source instead of a VCLK. The patch implements this as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The 16bpp mode did not work on the Cirrus cards as the visual type was set
to DIRECTCOLOR instead of TRUECOLOR. The Alpine family used one incorrect
register setting so this 16bpp modes generated wrong horizontal frequency.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The noaccel parameter is already handled if the driver is not built as
module.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move call to pixclock calculation into the cirrusfb_set_par_foo(). It
makes copy of clock registers redundant.
Simplify clock calculations further.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move calculations of CRT register values into the cirrusfb_set_par_foo()
where the values are used.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add __devinit attribute to probing functions. This fixed section mismatch
warning from my previous patch.
Kill one redundant forward declaration.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use modedb for initial mode instead of table of few predefined modes.
Add mode_option module parameter as a step toward unification of frame
buffers' parameters.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The device pointer can be easily obtained from fb_info->device if needed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The 24 bpp mode is not implemented. Disallow it in the
cirrusfb_check_var() and remove it from checks.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Simplify clock calculation.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove information about memory size displayed twice each time a display
mode change.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
