| Age | Commit message (Collapse) | Author |
|---|
|
o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/bnx2x_main.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
drivers/net/wireless/rt2x00/rt73usb.c
|
|
There was a bug, which occasionally caused failure in PRAM initialization after
the cold boot.
Also incremented version number to 1.45.27.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a proper cast to the argument of PAGE_ALIGN macro so that the output
won't depend on its original type. Without this cast aligned value will be
truncated to the size of the argument type.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sge_buff_size may not be more than 0xffff.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing to contend with it.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a number of race conditions in the driver.
Up until now, "entry" pointer was initialized before acquiring the right lock.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes compilation, if the PCI core is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
debugfs ath9k/phy#/wiphy can be used to show the current list of
virtual wiphys and to add/remove virtual wiphys. Eventually, this
interface could be replaced with a cfg80211/nl80211 command that is
passed through mac80211.
For example:
# cat /debug/ath9k/phy0/wiphy
primary: phy0
# echo add > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
secondary: phy1
# echo del=phy1 > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
In addition, following commands can be used to test pausing and
unpausing of the virtual wiphys:
pause=phy1
unpause=phy1
select=phy1
(select pauses and unpauses wiphys automatically based on channel)
schedule=500
(set wiphy scheduling interval in msec; 0 = disable; default value: 500)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is a very simple scheduler that goes through the wiphys and
schedules one at a time every N milliseconds (current default value:
500 ms). This is enough for initial testing, but there are number of
areas where a more complex scheduler can improve operations greatly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow mac80211-controlled channel changes on an active wiphy and
especially during a scan. We need this as long as the scan is
controlled by mac80211. Moving this control into the driver could
allow some optimizations on scanning while using multiple virtual
interfaces, but for now, try to work as well as possible with the
current scan mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It looks like channel change may fail in some cases and end up leaving
the hardware in state where it cannot transmit any frames. Add a
workaround to recover from this state if we detect that wiphy
selection is failing due to wiphys not leaving PAUSING state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 should not be requesting us to transmit frames on paused
wiphys since we stop the TX queues. Just in case, add debug code to
make sure we catch if this were to happen.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For now, allow channel changes immediately and just force the other
virtual wiphys to paused state. This is needed to allow
mac80211-controlled scan to control channel changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Notify the AP that we may be sleeping longer to allow the AP power
save code to buffer larger number of frames for us when using virtual
wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of always going through initialization/deinitialization steps,
do this only for the first/last wiphy to not break the other wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_wiphy_select() can be used to select a virtual wiphy to be
activated. Other virtual wiphys will be paused and once that is done,
the operational channel is changed and the wiphys that are on the
selected channel will be unpaused.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).
The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.
Registration of secondary wiphys is added in a separate patch.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.
This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.
Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.
Also be more consistent with using tabs to seperate different
fields.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This makes the code easier to understand.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The only use case for this right now is ANI calibration,
but more might come up in the future.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).
This also removes some obsolete unused timestamping code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
So that a new created IBSS network
doesn't break on the first scan.
It seems to Sujith and me that this
stupid code unnecessary, too.
So remove it...
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Restore network sleep mode in isr if power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
