aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-02-09enic: Add api for link down count and to get firmware notification status.Scott Feldman
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09enic: bug fix: tx_timeout reset path fix-upsScott Feldman
tx_timeout reset path needs to re-init dev and re-apply nic cfg to enable vlan stripping. Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09enic: record all bad FCS errs as frame errorsScott Feldman
Report all bad FCS errs as frames errs. This includes frames with bad FCS on wire detected by MAC and frames which may be truncated due to ingress FIFO overruns. No longer print a driver msg on bad FCS err. Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09enic: bug fix: return notify intr creditsScott Feldman
Return notify intr credits after notify intr from firmware. This is especially important for legacy PCI intr mode, where not returning credits would cause PBA to remain asserted which would get us right back into the ISR. Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/gianfar.c
2009-02-09ppp: section fixes re netnsAlexey Dobriyan
PPP is modular code so no initdata on netns hooks. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09gianfar: Fix boot hangs while bringing up gianfar ethernetJarek Poplawski
Ira Snyder found that commit 8c7396aebb68994c0519e438eecdf4d5fa9c7844 "gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can cause hangs. It's because there was removed clearing of interrupts in gfar_schedule_cleanup() (which is called by an interrupt handler) in case when netif scheduling has been disabled. This patch brings back this action and a comment. Reported-by: Ira Snyder <iws@ovro.caltech.edu> Reported-by: Peter Korsgaard <jacmet@sunsite.dk> Bisected-by: Ira Snyder <iws@ovro.caltech.edu> Tested-by: Peter Korsgaard <jacmet@sunsite.dk> Tested-by: Ira Snyder <iws@ovro.caltech.edu> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-09b43: (b2062) Fix crystal frequency calculationsMichael Buesch
This fixes the crystal frequency calculations in the b2062 init code. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09b43: Port spec bugfixes for the LP baseband initMichael Buesch
A few bugs were fixed in the LP baseband init specs. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ssb: Add PMU supportMichael Buesch
This adds support for the SSB PMU. A PMU is found on Low-Power devices. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09libertas: pos[4] tested twice, 2nd should be pos[5]Roel Kluin
pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5] Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09libertas: if_spi: add ability to call board specific setup/teardown methodsMike Rapoport
In certain cases it is required to perform board specific actions before activating libertas G-SPI interface. These actions may include power up of the chip, GPIOs setup, proper pin-strapping and SPI controller config. This patch adds ability to call board specific setup/teardown methods Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: fix reg_notifier() flags used upon a country IELuis R. Rodriguez
The nl80211 rule flags were being used. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09b43: Add LP 2062 radio initMichael Buesch
This adds initialization code for the 2062 radio. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09b43: Add LP-PHY baseband init for >=rev2Michael Buesch
This adds code for the baseband init of LP-PHY >=2. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: another led naming fixDanny Kukawka
Fixed led device naming for the iwlwifi (iwl-3945) driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "iwl-%s::RX" instead of "iwl-%s:RX". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09rt2x00: fix led namingDanny Kukawka
Fixed led device naming for the rt2x00 driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "%s::radio" instead of "%s:radio". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09b43legacy: fix led namingDanny Kukawka
Fixed led device naming for the b43legacy driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "b43legacy-%s::rx" instead of "b43legacy-%s:rx". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: fix led namingDanny Kukawka
Fixed led device naming for the ath9k driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09b43: Add LP-PHY register definitionsMichael Buesch
This adds register definitions for the LP-PHY. This also adds a few minor empty function bodies for the LP-init. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09Add new rt73usb USB IDIvo van Doorn
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09mac80211: remove HW_SIGNAL_DBJohannes Berg
Giving the signal in dB isn't much more useful to userspace than giving the signal in unspecified units. This removes some radiotap information for zd1211 (the only driver using this flag), but it helps a lot for getting cfg80211-based scanning which won't support dB, and zd1211 being dB is a little fishy anyway. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Bruno Randolf <bruno@thinktube.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Add debugfs files for printing TX rate detailsSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Handle mac80211's RC flags for MCS ratesSujith
mac80211 notifies the RC algorithm if RTS/CTS and short preamble are needed. The RC flags for MCS rates are currently not handled by mac80211, and ath9k's RC doesn't set the flags either. Fix this. Also, set the rts_cts_rate_idx inside the RC algorithm. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Cleanup get_rate() interfaceSujith
The interface to calculate the TX rate for a data frame was convoluted with lots of redundant arguments being passed around. Remove all of that and make it simple. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath5k: properly free rx dma descriptorsFelix Fietkau
When freeing rx dma descriptors, use the right buffer size. Fixes kernel oopses on module unload on ixp4xx and most likely other platforms as well. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09wireless: replace uses of __constant_{endian}Harvey Harrison
The base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: fix led namingDanny Kukawka
Fixed led device naming for the iwl driver. Due to the documentation of the led subsystem/class the naming should be "devicename:colour:function" while not applying sections should be left blank. This should lead to e.g. "iwl-phy0::RX" instead of "iwl-phy0:RX". Signed-off-by: Danny Kukawka <dkukawka@suse.de> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ipw2x00: correct Kconfig to prevent following entries from not indentingJay Sternberg
not defining dependencies for LIBIPW caused the following entries to not be indented. changing this entry to depend on PCI && WLAN_80211 corrects this issue Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: remove chain noise calibration functions from 6000 familyJay Sternberg
redefine structures that contain function pointer for chain noise reset and chain noise gain for the 6000 family since these are not needed. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: define structures and functions externally for customizationJay Sternberg
defined the structures and functions as extern to alter behavior used by 5000 series for other products including 100 and 6000 series Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: correct API command overlapJay Sternberg
Correct the API commands where same command id used for two different commands. Update max api versions for affected devices. TX_ANT_CONFIGURATION_CMD was already using id 0x98, so REPLY_TX_POWER_DBM_CMD moved to 0x95 Older API interfaces may used original value so V1 defines provided. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: parametrize configuration of the PLL for exclusion on 6000Jay Sternberg
added a config parameter to enable setting PLL_CFG. older hardware has this parameter set true. the 6000 family does not support this setting, so this parameter set false. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: simplify parameter setting to allow support for 6000 seriesJay Sternberg
by parametrizing the set hw function, in addition to allowing for supporting the 6000 family significantly simplify the addition of new hardware. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: add new HW_REV_TYPEs for Intel WiFi Link 100, 6000 and 6050 SeriesJay Sternberg
simply add definitions for the HW_REV_TYPEs for the new devices. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Fix LED blink patternVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Remove a bunch of unused macrosSujith
RX filter masks are already defined in enum ath9k_rx_filter in ath9k.h Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Fix typo in checking for chip revisionSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: remove passive scan on 5 GHz if country IE knows betterLuis R. Rodriguez
If we have new found information about our location and the current country regulatory domain does not have passive scan flag requirements we should be able to actively scan now on those channels. Since AP functionality is not allowed where passive scan flags are set this means if you have a world regulatory domain and you get a country IE that allows that channel (with active scan) then we lift the passive-scan requirement so you can then use AP mode. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: move check for radar freqs into a helperLuis R. Rodriguez
This will be used later. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: replace usage of internal wireless_modes for confLuis R. Rodriguez
No need to use our internal wireless mode variable when cfg80211 already has its own. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Enable MIB and TIM interrupts for station mode.Vivek Natarajan
Enable operating mode specific interrupts in ath9k_add_interface instead of ath9k_start. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath9k: Fix lockdep warningSujith
This patch fixes the lockdep warning shown below, and also initializes the starting sequence number when starting a TX aggregation session. ============================================= [ INFO: possible recursive locking detected ] 2.6.29-rc2-wl #21 --------------------------------------------- swapper/0 is trying to acquire lock: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 but task is already holding lock: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 other info that might help us debug this: 7 locks held by swapper/0: #0: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 #1: (_xmit_ETHER#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 #2: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 #3: (_xmit_IEEE80211#2){-+..}, at: [<ffffffff80456d71>] __qdisc_run+0x221/0x290 #4: (rcu_read_lock){..--}, at: [<ffffffffa0154919>] ieee80211_master_start_xmit+0x219/0x6c0 [mac80211] #5: (rcu_read_lock){..--}, at: [<ffffffffa01427c6>] ieee80211_start_tx_ba_session+0x66/0x4e0 [mac80211] #6: (rcu_read_lock){..--}, at: [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 stack backtrace: Pid: 0, comm: swapper Not tainted 2.6.29-rc2-wl #21 Call Trace: <IRQ> [<ffffffff8026c329>] __lock_acquire+0x1be9/0x1c40 [<ffffffff80442af1>] dev_queue_xmit+0xe1/0x620 [<ffffffff8026a8cc>] __lock_acquire+0x18c/0x1c40 [<ffffffff8026c3d5>] lock_acquire+0x55/0x70 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff804dbeb9>] _spin_lock+0x39/0x50 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff804dbd2f>] _spin_unlock+0x1f/0x50 [<ffffffff80456d71>] __qdisc_run+0x221/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa0142a63>] ieee80211_start_tx_ba_session+0x303/0x4e0 [mac80211] [<ffffffffa01427c6>] ieee80211_start_tx_ba_session+0x66/0x4e0 [mac80211] [<ffffffffa0149dae>] rate_control_get_rate+0xae/0xc0 [mac80211] [<ffffffffa01526b5>] invoke_tx_handlers+0x655/0x1000 [mac80211] [<ffffffff802699fd>] mark_held_locks+0x4d/0x90 [<ffffffff804dbcf5>] _spin_unlock_irqrestore+0x65/0x80 [<ffffffffa0151aaa>] __ieee80211_tx_prepare+0x16a/0x310 [mac80211] [<ffffffffa0151adc>] __ieee80211_tx_prepare+0x19c/0x310 [mac80211] [<ffffffff80439cc2>] pskb_expand_head+0x112/0x190 [<ffffffffa0154986>] ieee80211_master_start_xmit+0x286/0x6c0 [mac80211] [<ffffffffa0154919>] ieee80211_master_start_xmit+0x219/0x6c0 [mac80211] [<ffffffff8026a8cc>] __lock_acquire+0x18c/0x1c40 [<ffffffff80456d8e>] __qdisc_run+0x23e/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa0154221>] ieee80211_subif_start_xmit+0x4a1/0x980 [mac80211] [<ffffffffa0153f18>] ieee80211_subif_start_xmit+0x198/0x980 [mac80211] [<ffffffff80456d8e>] __qdisc_run+0x23e/0x290 [<ffffffff80442d18>] dev_queue_xmit+0x308/0x620 [<ffffffff80442a63>] dev_queue_xmit+0x53/0x620 [<ffffffffa028ecfd>] ip6_output+0x62d/0x1230 [ipv6] [<ffffffff8024ca00>] __mod_timer+0xb0/0xd0 [<ffffffffa02ad25a>] mld_sendpack+0x3fa/0x4a0 [ipv6] [<ffffffffa02ace60>] mld_sendpack+0x0/0x4a0 [ipv6] [<ffffffffa02adf90>] mld_ifc_timer_expire+0x0/0x340 [ipv6] [<ffffffffa02ae219>] mld_ifc_timer_expire+0x289/0x340 [ipv6] [<ffffffffa02adf90>] mld_ifc_timer_expire+0x0/0x340 [ipv6] [<ffffffff8024c097>] run_timer_softirq+0x147/0x220 [<ffffffff802473fb>] __do_softirq+0x9b/0x180 [<ffffffff80265516>] tick_dev_program_event+0x36/0xb0 [<ffffffff8020d77c>] call_softirq+0x1c/0x30 [<ffffffff8020f2c5>] do_softirq+0x65/0xb0 [<ffffffff80246ebd>] irq_exit+0x9d/0xc0 [<ffffffff80221db6>] smp_apic_timer_interrupt+0x86/0xd0 [<ffffffff8020d1b3>] apic_timer_interrupt+0x13/0x20 Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09rt2x00: Validate firmware in driverIvo van Doorn
The get_firmware_crc() callback function isn't flexible enough when dealing with multiple firmware versions. It might in some cases be possible that the firmware file contains multiple CRC checksums. Create the check_firmware() callback function where the driver has complete freedom in how to validate the firmware. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09rt2x00: Add kill_tx_queue callback functionIvo van Doorn
provide rt2x00lib the possibility to kill a particular TX queue. This can be useful when disabling the radio, but more importantly will allow beaconing to be disabled when mac80211 requests this (during scanning for example) Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09rt2x00: Move intf_work to mac82011 workqueueIvo van Doorn
ieee80211_iterate_active_interfaces() no longer acquires the RTNL lock which means the intf_work handler can be safely used from the mac80211 workqueue again. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: unify iwlagn and 3945 power save managementWinkler, Tomas
This patch unifies 3945 and iwlagn power save management This patch also better separates system state from user setting. System state shall be removed later as this shall be shifted to user space Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: don't use implicit priv in IWL_DEBUGTomas Winkler
Call IWL_DEBUG macro with explicit priv argument. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: check return value of pci_enable_deviceWinkler, Tomas
pci_enable_device is tagged with __must_check therefore don't ignore the return value in pci_resume handlers Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09iwlwifi: iwl3945_send_tx_power must be staticWinkler, Tomas
iwl3945_send_tx_power must be static Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-07 02:41:36 +0000