| Age | Commit message (Collapse) | Author |
|---|
|
Bug fix for driver rndis_host which fixes rndis_host probing certain
Nokia S60 (Series 60) mobiles. While the rndis_host get probed by usbnet
and tries to bind the Nokia mobile the bind is going to fail. The
rndis_host module tries to release the device, in a wrong way, which
cause the oops.
Fixes Bugzilla #7201
Signed-off-by: Daniel Gollub <dgollub@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Different AX88772 dongles use different PHYs; the chip is capable of using
both a primary and secondary PHY, and supports an internal and external PHY.
It appears that some DUB-E100 devices use the internal PHY, so trying to use
an external one will not work (note that this is different across revisions,
as well; the "A" and "B" revs of the DUB-E100 use different PHYs!). The data
sheet for the AX88772 chip specifies that the internal PHY id will be 0x10,
so if that's read from the EEPROM, we should use that rather than attempting
to use an external PHY.
Thanks to Mitch Bradley for pointing this out!
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: David Hollis <dhollis@davehollis.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
ITM screens send invalid x/y data when not touched. this was fixes a while ago
but the problem is if the screen is not touched anymore the driver never does
not report BTN_TOUCH as zero. fix it by sending the report with the last valid
coordinates when pressure is released.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (30 commits)
[SCSI] qla1280: set residual correctly
[SCSI] fusion: bump version
[SCSI] fusion: MODULE_VERSION support
[SCSI] fusion: power pc and miscellaneous bug fixs
[SCSI] fusion: fibre channel: return DID_ERROR for MPI_IOCSTATUS_SCSI_IOC_TERMINATED
[SCSI] megaraid_sas: Update module author
[SCSI] 3ware 8000 serialize reset code
[SCSI] sr: fix error code check in sr_block_ioctl()
[SCSI] scsi: lpfc error path fix
[SCSI] aacraid: Product List Update
[SCSI] libiscsi: fix senselen calculation
[SCSI] iscsi: simplify IPv6 and IPv4 address printing
[SCSI] iscsi: newline in printk
[SCSI] iscsi: fix crypto_alloc_hash() error check
[SCSI] iscsi: fix 2.6.19 data digest calculation bug
[SCSI] scsi_scan: fix report lun problems with CDROM or RBC devices
[SCSI] qla2xxx: Update version number to 8.01.07-k4.
[SCSI] qla2xxx: Use generic isp_ops.fw_dump() function.
[SCSI] qla2xxx: Perform a fw-dump when an ISP23xx RISC-paused state is detected.
[SCSI] qla2xxx: Correct reset handling logic.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
hid-core.c: Adds GTCO CalComp Interwrite IPanel PIDs to blacklist
HID: put usb_interface instead of usb_device into hid->dev to fix udevinfo breakage
HID: add missing RX, RZ and RY enum values to hid-debug output
HID: hid/hid-input.c doesn't need to include linux/usb/input.h
HID: compilation fix when DEBUG_DATA is defined
HID: proper LED-mapping for SpaceNavigator
HID: update MAINTAINERS entry for USB-HID
HID: GEYSER4_ISO needs quirk
HID: fix some ARM builds due to HID brokenness - make USB_HID depend on INPUT
|
|
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon/w83793: Hide invalid VID readings
hwmon/w83793: Fix the fan input detection
hwmon/w83793: Ignore disabled temperature channels
hwmon: Fix the VRD 11 decoding
hwmon/w83793: Remove the description of AMDSI and update the voltage formula
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (5023): Fix compilation on ppc32 architecture
V4L/DVB (5071): Tveeprom: autodetect LG TAPC G701D as tuner type 37
V4L/DVB (5069): Fix bttv and friends on 64bit machines with lots of memory
V4L/DVB (5033): MSI TV@nywhere Plus fixes
V4L/DVB (5029): Ks0127 status flags
V4L/DVB (5024): Fix quickcam communicator driver for big endian architectures
V4L/DVB (5021): Cx88xx: Fix lockup on suspend
V4L/DVB (5020): Fix: disable interrupts while at KM_BOUNCE_READ
V4L/DVB (5019): Fix the frame->grabstate update in read() entry point.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: Correct definition of R6
omap: Update MMC response types
|
|
This reverts commit 99a10a60ba9bedcf5d70ef81414d3e03816afa3f.
As per Hugh Dickins:
"Nadia Derbey has reported that mmap of /dev/kmem no longer works with
the kernel virtual address as offset, and Franck has confirmed that
his patch came from a misunderstanding of what an offset means to
/dev/kmem - whereas his patch description seems to say that he was
correcting the offset on a few plaforms, there was no such problem to
correct, and his patch was in fact changing its API on all platforms."
Suggested-by: Hugh Dickins <hugh@veritas.com>
Cc: Franck Bui-Huu <fbuihuu@gmail.com>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds GTCO CalComp Interwrite IPanels to the hid-core.c blacklist.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
breakage
The commit 4916b3a57fc94664677d439b911b8aaf86c7ec23 introduced a
hid regression between 2.6.19 and 2.6.20-rc1. The device put in
input_dev->cdev is now of type usb_device instead of usb_interface.
Before:
> # readlink -f /sys/class/input/input6/event4/device
> /sys/devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.1
After:
> # readlink -f /sys/class/input/input3/event3/device
> /sys/devices/pci0000:00/0000:00:10.0/usb1/1-1
This causes breakage:
> # udevinfo -q all -n /dev/input/event3
> P: /class/input/input3/event3
> N: input/event3
> S: input/by-path/pci-1-1--event-
> E: ID_SERIAL=noserial
> E: ID_PATH=pci-1-1-
No ID_MODEL, ID_VENDOR, ID_REVISION, ID_TYPE etc etc.
Fix this by assigning the intf->dev into hid->dev, and fixing
all the users.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There is no reason for generic hid-input.c to include usb-specific
input.h.
As a sideeffect, this also fixes warning of redefinition of dbg()
macro, when hid-input.c is compiled with DEBUG (as there is a clash
between dbg() from hid.h and usb/input.h).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid/hid-core.c references 'len' variable when DEBUG_DATA is defined,
but the actual name of the variable is 'size'. Fix it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This change introduces a mapping for LED indicators between the HID
specification and the Linux input subsystem. The previous code properly
mapped the LEDs relevant for Keyboards, but garbeled the remaining ones.
With this change all LED enums from the input system get mapped to more
or less equivalent LED numbers from the HID specification.
This patch also ensures that the unused bits in a HID report to the
device are zeroed out. This makes the 3Dconnexion SpaceNavigator fully
usable with the linux input system.
Signed-off-by: Simon Budig <simon@budig.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
I've got a newer MacBook with core2duo. Two keys on the keyboard are
swapped, "unswaping" works with the same trick as GEYSER3_ISO.
Signed-off-by: Adrian Friedli <masteradi@gmx.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We have USB_HID _newly_ selected in configurations which didn't
have it before, which overrides CONFIG_HID and builds HID without
input support.
Nevertheless, here's a patch to solve more of the same that my original
patch attempted to solve. The original patch is still required. Seems
to solve the final instance of this problem here.
Signed-off-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Ignore the VID readings when the motherboard has not designed
the function.
Signed-off-by: Gong Jun <jgong@winbond.com>
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Catch the cases when alternative pins are used to route the
fan9-12 input.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Gong Jun <jgong@winbond.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Ignore the temperature readings when its channel is disabled,
ignore AMDSI readings.
Signed-off-by: Gong Jun <jgong@winbond.com>
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
I wonder how we came up with such a broken test in the first place.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix the driver to match the information in datasheet 1.0. AMD
SI interface is marked as reserved, computing formula for 5VDD
and 5VSB is updated.
Signed-off-by: Gong Jun <jgong@winbond.com>
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
There's a problem, pointed by Meelis Roos <mroos@linux.ee>, that, on ppc32 arch,
with some gcc versions (noticed with prerelease 4.1.2 20061115), compilation
fails, due the lack of __ucmpdi2 to do the required 64-bit comparision.
This patch takes some sugestions made by Andrew Morton <akpm@osdl.org>,
Stelian Pop <stelian@popies.net> and Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
autodetect LG TAPC G701D as tuner type 37.
Thanks to Adonis Papas, for pointing out the missing autodetection
for this tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
We have a DMA32 zone now, lets use it to make sure the card
can reach the memory we have allocated for the video frame
buffers.
Signed-off-by: Gerds Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- MSI TV@nywhere Plus. Fix radio, S-Video and external analog audio in
as far we can know currently.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Or status flags together in DECODER_GET_STATUS instead of and-zapping them.
Signed-off-by: Martin Samuelsson <sam@home.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Host endianess does not affect the order that pixel rgb data comes
in from the quickcam (the values are bytes, not words or longs). The
driver is erroniously swapping the order of rgb values for big endian
machines. This patch is needed get the Quickcam communicator working
on big endian machines (tested on powerpc)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Suspending with the cx88xx module loaded causes the system to lock up
because the cx88_audio_thread kthread was missing a try_to_freeze()
call, which caused it to go into a tight loop and result in softlockup
when suspending. Fix that.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
vivi.c uses the KM_BOUNCE_READ with local interrupts enabled.
This means that if a disk interrupt occurs while vivi.c is using this
fixmap slot, the vivi.c driver will, upon return from that interrupt, find
that the fixmap slot now points at a different physical page.
The net result will probably be rare corruption of disk file contents,
because viv.c will now be altering the page which the disk code was
recently using.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The Coverity checker spotted that in usbvision_v4l2_read(), the variable
"frmx" is never assigned any value different from -1, but it's used an
an array index in "usbvision->frame[frmx]".
Thanks to Adrian Bunk <bunk@stusta.de> for warning about that.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
During development of SDHC support, it was discovered that the definition
for R6 was incorrect. This patch fixes that and patches the drivers that
do switch on the response type.
Signed-off-by: Philip Langdale <philipl@overt.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pavel Pisa <ppisa@pikron.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is a fix in order to update MMC response types. This modification is
needed to allow SD card support on OMAP platforms.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Yuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: Fix DRIVER_DESC macro
HID: mousepoll parameter makes no sense for generic HID
HID: tiny patch to remove a kmalloc cast
HID: fix mappings for DiNovo Edge Keyboard - Logitech USB BT receiver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
Revert "ACPI: ibm-acpi: make non-generic bay support optional"
ACPI: update MAINTAINERS
ACPI: schedule obsolete features for deletion
ACPI: delete two spurious ACPI messages
ACPI: rename cstate_entry_s to cstate_entry
ACPI: ec: enable printk on cmdline use
ACPI: Altix: ACPI _PRT support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
i915: Fix a DRM_ERROR that should be DRM_DEBUG.
|
|
Setting .ConfigBase and .Present is now done at the pcmcia core.
The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS. Setting to
PRESENT_OPTION now overrides the values from the CIS. So just remove
those lines.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This changes all HWRNG driver initcalls to module_init(). We must probe
the RNGs after the major kernel subsystems are already up and running (like
PCI).
This fixes Bug 7730.
http://bugzilla.kernel.org/show_bug.cgi?id=7730
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a load option to intel-rng to allow skipping the FWH detection,
necessary in case the BIOS has locked read-only the firmware hub space.
Also prevent any attempt to write to firmware space if it cannot be write
enabled (apparently caused hangs on some systems not having an FWH and thus
also not having a respective RNG).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix void cast and re-enable on sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds the profile=kvm boot option, which enables KVM to profile VM
exits.
Use: "readprofile -m ./System.map | sort -n" to see the resulting
output:
[...]
18246 serial_out 148.3415
18945 native_flush_tlb 378.9000
23618 serial_in 212.7748
29279 __spin_unlock_irq 622.9574
43447 native_apic_write 2068.9048
52702 enable_8259A_irq 742.2817
54250 vgacon_scroll 89.3740
67394 ide_inb 6126.7273
79514 copy_page_range 98.1654
84868 do_wp_page 86.6000
140266 pit_read 783.6089
151436 ide_outb 25239.3333
152668 native_io_delay 21809.7143
174783 mask_and_ack_8259A 783.7803
362404 native_set_pte_at 36240.4000
1688747 total 0.5009
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.
Fixing this in raid1 and raid10 seems to be straightforward enough.
For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This fixes the SH rtc driver to
(a) correctly report 'enabled' status with other alarm status;
(b) not duplicate that status in its procfs dump
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While testing 2.6.20-rc3 on a machine with some CK804 chipsets, we noticed
that quirk_nvidia_ck804_msi_ht_cap() was not detecting HT MSI capabilities
anymore. It is actually caused by the MSI mapping on the root chipset
being the 2nd HT capability in the chain. pci_find_ht_capability() does
not seem to find anything but the first HT cap correctly, because it
forgets to increment the position before looking for the next cap. The
following patch seems to fix it.
At least, this proves that having a ttl is good idea since the machine
would have been stucked in an infinite loop if we didn't have a ttl :)
We have to pass pos + PCI_CAP_LIST_NEXT to __pci_find_next_cap_ttl to
get the next HT cap instead of the same one again.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This reverts commit 2df910b4c3edcce9a0c12394db6f5f4a6e69c712.
ACPI_BAY has not been merged into mainline yet, so the changes to ibm-acpi
related Kconfig entries that depend on ACPI_BAY were permanently disabling
ibm-acpi bay support. This is a serious regression for ThinkPad users.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
|
|
ACPI: Getting cpuindex for acpiid 0x4
acpi_processor-0742 [00] processor_preregister_: Error while parsing _PSD domain information. Assuming no coordination
http://bugzilla.kernel.org/show_bug.cgi?id=7286
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Fix warnings in ia32_aout.c
[PATCH] i386: Convert some functions to __init to avoid MODPOST warnings
[PATCH] i386: Fix memory hotplug related MODPOST generated warning
[PATCH] x86-64: tighten up printks
[PATCH] x86-64: - Ignore long SMI interrupts in clock calibration
[PATCH] x86-64: pci quirks MODPOST warning fix
[PATCH] x86-64: Modpost whitelist reference to more symbols (pattern 3)
[PATCH] x86-64: modpost add more symbols to whitelist pattern2
[PATCH] i386: make apic probe function non-init
[PATCH] i386: cpu hotplug/smpboot misc MODPOST warning fixes
[PATCH] x86-64: Use different constraint for gcc < 4.1 in bitops.h
[PATCH] x86-64: Make noirqdebug_setup function non init to fix modpost warning
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
|
|
o MODPOST generates warnings for i386 if kernel is compiled with
CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'
o Two quirk functions which are non __init, are accessing data which is
of type __init.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
