| Age | Commit message (Collapse) | Author |
|---|
|
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1069: warning: cast from pointer to integer of different size
drivers/net/82596.c: In function 'i82596_probe':
drivers/net/82596.c:1249: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Updated direct resource pass with ioremap call, make it grant proper IRQ
mapping, stuff incompatible with the new approach were respectively put
under #ifndef CONFIG_PPC_MERGE. It is required so that both ppc and
powerpc could utilize fs_enet effectively.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
On error we should start freeing resources at [i-1] not [i-2].
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This fixes the issue of frequent link changes under heavy traffic reported
below:
http://bugzilla.kernel.org/show_bug.cgi?id=7696
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=216338
The b44 chip occasionally needs to be reset when ISTAT_ERRORS are
encountered. The reset sequence includes a PHY reset that will take many
seconds to complete and cause the link to go down and up. By skipping the
PHY reset, it will greatly reduce the interruption when ISTAT_ERRORS are
encountered.
Change the full_reset parameter to reset_kind parameter in b44_init_hw().
This will allow PHY reset to be skipped when ISTAT_ERRORS are encountered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
libata's SCSI translation for the SCSI START STOP UNIT command with the
START bit clear (i.e. stopping the drive) appears to be incorrect. It
sends an ATA STANDBY command with the time period set to 0, which the code
comment says means "now", but the ATA standard says this means disable the
standby timer, which effectively does nothing. Change this to issue a
STANDBY IMMEDIATE command which will actually spin the drive down. The SAT
(SCSI/ATA Translation) standard revision 9 concurs with this choice.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
User applications using the HDIO_DRIVE_TASK ioctl through libata expect
specific ATA registers to be returned to userspace. Verified that
ata_task_ioctl correctly returns register values to the smartctl
application.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
drivers/ata/pata_platform.c:85: warning: initialization from incompatible pointer type
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
If word 53 bit 1 isn't set, the maximum PIO mode is indicated by
the upper 8 bits of word 51, not the lower 8 bits. Fixes PIO mode
detection on old Compact Flash cards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix PIO mode 1 overclocked taskfile transfers -- probably a typo carried over
from drivers/ide/pci/siimage.c where I've found it by documentation check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.
This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Let's just backout the IRQ hack, and for those crap machines (like some
Sony VAIO's) can just disable MSI with the module parameter.
This reverts 44ade178249fe53d055fd92113eaa271e06acddd.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frédéric Riss <frederic.riss@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Trivial patch to check sysfs_create_link return values.
Fail gracefully if needed.
Signed-off-by: Ahmed Darwish <darwish.07@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Culled from the VIA codedrop.
Also fixes up one ID used in amd64-agp to use the
VIA part number instead of the board name in its ID.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
No point in clearing local pointers then returning.
Also fix up some CodingStyle nits.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This seems to exist just to save people typing 'struct' a few times,
and doesn't provide any additional value.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
If we fail an alloc, unwind the previous allocs that succeeded.
Spotted-by: Alan Grimes <agrimes@speakeasy.net>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
for CX700 and 8237S
This patch:
* Corrects the wrong device ID of PCI_DEVICE_ID_VIA_SATA_EIDE
from 0x0581 to 0x5324.
* Adds VIA CX700 and VT8237S support in drivers/ide/pci/via82cxxx.c
* Adds VIA VT8237S support in drivers/ata/pata_via.c
Signed-off-by: Josepch Chan <josephchan@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
idepnp driver is registered as a pnp driver on ide init but doesn't
get unregistered on ide unload causing driver list corruption and
eventually oops. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Drop ide-generic support for Jmicron identifiers as we now trust Jmicron.c for
this with drivers/ide. The code check remains for the all-generic-ide case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
IDE HDD does not work if it uses a 40-pin PATA cable on ATI chipset.
This patch fixes the bug.
Signed-off-by: Conke Hu <conke.hu@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
AMD/ATI SB600 IDE/PATA controller only has one channel.
Signed-off-by: Conke Hu <conke.hu@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
A previous patch to atiixp.c was removed but some code has not been
cleaned. Now we remove these code sine they are no use any longer.
Signed-off-by: Conke Hu <conke.hu@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ata_eh_suspend() was returning 0 regardless of failure. This bug has
potential to lose data on suspend. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ap->id is logcial port ID which is unique among all ATA ports and
doesn't have anything to do with hardware port index. ap->port_no is
the hardware port index and thus should be used when clearing IRQ mask
in ahci_thaw().
This problem has been spotted by Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: nf_conntrack_pptp: fix NAT setup of expected GRE connections
[NETFILTER]: nf_nat_pptp: fix expectation removal
[NETFILTER]: nf_nat: fix ICMP translation with statically linked conntrack
[TCP]: Restore SKB socket owner setting in tcp_transmit_skb().
[AF_PACKET]: Check device down state before hard header callbacks.
[DECNET]: Handle a failure in neigh_parms_alloc (take 2)
[BNX2]: Fix 2nd port's MAC address.
[TCP]: Fix sorting of SACK blocks.
[AF_PACKET]: Fix BPF handling.
[IPV4]: Fix the fib trie iterator to work with a single entry routing tables
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Fix Maple PATA IRQ assignment.
ahci: use 0x80 as wait stat value instead of 0xff
sata_via: style clean up, no indirect method call in LLD
ahci: fix endianness in spurious interrupt message
libata-sff: Don't call bmdma_stop on non DMA capable controllers
libata: implement ATA_FLAG_IGN_SIMPLEX and use it in sata_uli
ahci: improve and limit spurious interrupt messages, take#3
sata_via: don't diddle with ATA_NIEN in ->freeze
libata: set_mode, Fix the FIXME
libata hpt3xn: Hopefully sort out the DPLL logic versus the vendor code
libata cmd64x: whack into a shape that looks like the documentation
|
|
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Before hardreset, ahci initialized stat part of received FIS area to
0xff to wait for the first D2H Reg FIS which would change the value to
device ready state. This used to work but now libata considers status
value of 0xff as device not present making this wait prone to failure.
This patch makes ahci use 0x80 for the wait stat value instead of
0xff to fix the above problem.
Signed-off-by: Tejun Heo <htejun@gmail.com>
drivers/ata/ahci.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Call ata_bmdma_irq_clear() directly instead of through
ap->ops->irq_clear() according to libata style guideline.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix endianness in spurious interrupt message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix race when deleting an EFI variable and issuing another EFI command on
the same variable. The removal of the variable from the efivars_list
should be done in efivar_delete and not delayed until the kobject release.
Furthermore, remove the item from the list at module unload time, and use
list_for_each_entry_safe() rather than list_for_each_safe() for
readability.
Tested on ia64.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
raid5_mergeable_bvec tries to ensure that raid5 never sees a read request
that does not fit within just one chunk. However as we must always accept
a single-page read, that is not always possible.
So when "in_chunk_boundary" fails, it might be unusual, but it is not a
problem and printing a message every time is a bad idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
rtc_sysfs_add_device is needed even after dev initialization, so drop __devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow noflush suspend/resume of device-mapper device only for the case
where the device size is unchanged.
Otherwise, dm-multipath devices can stall when resumed if noflush was used
when suspending them, all paths have failed and queue_if_no_path is set.
Explanation:
1. Something is doing fsync() on the block dev,
holding inode->i_sem
2. The fsync write is blocked by all-paths-down and queue_if_no_path
3. Someone requests to suspend the dm device with noflush.
Pending writes are left in queue.
4. In the middle of dm_resume(), __bind() tries to get
inode->i_sem to do __set_size() and waits forever.
'noflush suspend' is a new device-mapper feature introduced in
early 2.6.20. So I hope the fix being included before 2.6.20 is
released.
Example of reproducer:
1. Create a multipath device by dmsetup
2. Fail all paths during mkfs
3. Do dmsetup suspend --noflush and load new map with healthy paths
4. Do dmsetup resume
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In most cases we check the size of the bitmap file before reading data from
it. However when reading the superblock, we always read the first PAGE_SIZE
bytes, which might not always be appropriate. So limit that read to the size
of the file if appropriate.
Also, we get the count of available bytes wrong in one place, so that too can
read past the end of the file.
Cc: "yang yin" <yinyang801120@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that we sometimes step the array events count backwards (when
transitioning dirty->clean where nothing else interesting has happened - so
that we don't need to write to spares all the time), it is possible for the
event count to return to zero, which is potentially confusing and triggers and
MD_BUG.
We could possibly remove the MD_BUG, but is just as easy, and probably safer,
to make sure we never return to zero.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When 'repair' finds a block that is different one the various parts of the
mirror. it is meant to write a chosen good version to the others. However it
currently writes out the original data to each. The memcpy to make all the
data the same is missing.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix several flaws in the error handling of the Siemens Gigaset ISDN driver,
including one that would cause an Oops when connecting more than one device
of the same type.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recently cpufreq support on my laptop (Lenovo T60) broke completely: when
it's plugged into AC it would never go higher than 1 GHz - neither 1.3 GHz
nor 1.83 GHz is possible - no matter which governor (userspace, speed or
ondemand) is used.
After some cpufreq debugging i tracked the regression back to the following
(totally correct) bug-fix commit:
commit 0916bd3ebb7cefdd0f432e8491abe24f4b5a101e
Author: Dave Jones <davej@redhat.com>
Date: Wed Nov 22 20:42:01 2006 -0500
[PATCH] Correct bound checking from the value returned from _PPC method.
This bugfix, which makes other laptops work, made a previously hidden
(BIOS) bug visible on my laptop.
The bug is the following: if the _PPC (Performance Present Capabilities)
optional ACPI object is queried /after/ bootup then the BIOS reports an
incorrect value of '2'.
My laptop (Lenovo T60) has the following performance states supported:
0: 1833000
1: 1333000
2: 1000000
Per ACPI specification, a _PPC value of '0' means that all 3 performance
states are usable. A _PPC value of '1' means states 1 .. 2 are usable, a
value of '2' means only state '2' (slowest) is usable.
now, the _PPC object is optional, and it also comes with notification.
Furthermore, when a CPU object is initialized, the _PPC object is
initialized as well. So the following evaluation of the _PPC object is
superfluous:
[<c028ba5f>] acpi_processor_get_platform_limit+0xa1/0xaf
[<c028c040>] acpi_processor_register_performance+0x3b9/0x3ef
[<c0111a85>] acpi_cpufreq_cpu_init+0xb7/0x596
[<c03dab74>] cpufreq_add_dev+0x160/0x4a8
[<c02bed90>] sysdev_driver_register+0x5a/0xa0
[<c03d9c4c>] cpufreq_register_driver+0xb4/0x176
[<c068ac08>] acpi_cpufreq_init+0xe5/0xeb
[<c010056e>] init+0x14f/0x3dd
And this is the point where my laptop's BIOS returns the incorrect value of
'2'. Note that it has not sent any notification event, so the value is
probably not really intentional (possibly spurious), and Windows likely
doesnt query it after bootup either. Maybe the value is kept at '2'
normally, and is only set to the real value when a true asynchronous event
(such as AC plug event, battery switch, etc.) occurs.
So i /think/ this is a grey area of the ACPI spec: per the letter of the
spec the _PPC value only changes when notified, so there's no reason to
query it after the system has booted up. So in my opinion the best (and
most compatible) strategy would be to do the change below, and to not
evaluate the _PPC object in the acpi_processor_get_performance_info() call,
but only evaluate it if _PPC is present during CPU object init, or if it's
notified during an asynchronous event. This change is more permissive than
the previous logic, so it definitely shouldnt break any existing system.
This also happens to fix my laptop, which is merrily chugging along at
1.83 GHz now. Yay!
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a SPI master device exists, udev (udevtrigger) causes kernel crash, due
to wrong kobj pointer in kobject_uevent_env(). This problem was not in
2.6.19.
The backtrace (on MIPS) was:
[<8024db6c>] kobject_uevent_env+0x54c/0x5e8
[<802a8264>] store_uevent+0x1c/0x3c (in drivers/class.c)
[<801cb14c>] subsys_attr_store+0x2c/0x50
[<801cb80c>] flush_write_buffer+0x38/0x5c
[<801cb900>] sysfs_write_file+0xd0/0x190
[<80181444>] vfs_write+0xc4/0x1a0
[<80181cdc>] sys_write+0x54/0xa0
[<8010dae4>] stack_done+0x20/0x3c
flush_write_buffer() passes kobject of spi_master_class.subsys to
subsys_addr_store(), then subsys_addr_store() passes a pointer to a struct
subsystem to store_uevent() which expects a pointer to a struct
class_device. The problem seems subsys_attr_store() called instead of
class_device_attr_store().
This mismatch was caused by commit
3bd0f6943520e459659d10f3282285e43d3990f1, which overrides kset of master
class. This made spi_master_class.subsys.kset.ktype NULL so
subsys_sysfs_ops is used instead of class_dev_sysfs_ops.
The commit was to fix spi_busnum_to_master(). Here is a patch fixes
this function in other way, just searching children list of
class_device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently the spi mode can be set to the wrong mode if you are switching
from any mode other than mode 0. This is because the mode is set using a
bitwise or on uncleared bits. The following patch clears the mode bits
before setting the new mode. I've also modified it to use the appropriate
defines from pxa-regs.h for readability.
Signed-off-by: Justin Clacherty <justin@redfish-group.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out that the spi chipselect was not being passed to the set_cs
routine if one was specified in the platform data.
As part of the fix, change to using a set_cs field in the controller state,
and put a default gpio routine in if the data passed does not specify it.
Also remove the //#define DEBUG
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch implements forwarding of SHUTDOWN intercepts from the guest on to
userspace on AMD SVM. A SHUTDOWN event occurs when the guest produces a
triple fault (e.g. on reboot). This also fixes the bug that a guest reboot
actually causes a host reboot under some circumstances.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the recent guest page fault change, we perform access checks on our
own instead of relying on the cpu. This means we have to perform the nx
checks as well.
Software like the google toolbar on windows appears to rely on this
somehow.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Check pte permission bits in walk_addr(), instead of scattering the checks all
over the code. This has the following benefits:
1. We no longer set the accessed bit for accessed which fail permission checks.
2. Setting the accessed bit is simplified.
3. Under some circumstances, we used to pretend a page fault was fixed when
it would actually fail the access checks. This caused an unnecessary
vmexit.
4. The error code for guest page faults is now correct.
The fix helps netbsd further along booting, and allows kvm to pass the new mmu
testsuite.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This allows netbsd 3.1 i386 to get further along installing.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
