| Age | Commit message (Collapse) | Author |
|---|
|
BUG: warning at kernel/lockdep.c:1816/trace_hardirqs_on() (Not tainted)
[<c04051ee>] show_trace_log_lvl+0x58/0x171
[<c0405802>] show_trace+0xd/0x10
[<c040591b>] dump_stack+0x19/0x1b
[<c043abee>] trace_hardirqs_on+0xa2/0x11e
[<c06143c3>] _spin_unlock_irq+0x22/0x26
[<c0541540>] rtc_get_rtc_time+0x32/0x176
[<c0419ba4>] hpet_rtc_interrupt+0x92/0x14d
[<c0450f94>] handle_IRQ_event+0x20/0x4d
[<c0451055>] __do_IRQ+0x94/0xef
[<c040678d>] do_IRQ+0x9e/0xbd
[<c0404a49>] common_interrupt+0x25/0x2c
DWARF2 unwinder stuck at common_interrupt+0x25/0x2c
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fixes an error in kerneldoc of ata_piix.c.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixes section mismatch warnings when built as a module.
Also, mark find_ledma and sun4 init function as __devinit
too.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
he_init_one() is declared __devinit, but calls lots of init functions
that are marked __init. However, if CONFIG_HOTPLUG is enabled,
__devinit functions go into normal .text, which leads to
WARNING: drivers/atm/he.o - Section mismatch: reference to .init.text: from .text between 'he_start' (at offset 0x2130) and 'he_service_tbrq'
Fix this by changing the __init functions to __devinit.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To whoever had written that code:
a) priority of >> is higher than that of &
b) priority of typecast is higher than that of any binary operator
c) learn the fscking C
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ql3xxx_probe() does ioremap and stores result in ->mem_map_registers.
On failure exit it does iounmap() of the same thing.
OTOH, ql3xxx_remove() does iounmap() of ->mmap_virt_base which is
(a) never assigned and
(b) never used other than in that iounmap() call.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
the driver is still shite, though...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some user tools parse /proc/scsi/scsi, so we can't yet change the names.
Change the existing ones back to their old names, and add an admonition
to not make the same mistake that I did.
Andrew Morton reports that this was breaking YDL 4.1 userspace.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
marked as such...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
no ioread*(), for one thing
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (50 commits)
[libata] Delete pata_it8172 driver
[PATCH] libata: improve handling of diagostic fail (and hardware that misreports it)
[PATCH] libata: fix non-uniform ports handling
Fix libata resource conflict for legacy mode
[libata] ata_piix: build fix
[PATCH] pata_amd: Check enable bits on Nvidia
[PATCH] Update SiS PATA
[libata] Add pata_jmicron driver to Kconfig, Makefile
[libata #pata-drivers] Trim trailing whitespace.
[libata] Trim trailing whitespace.
[libata] Add a bunch of PATA drivers.
Rename libata-bmdma.c to libata-sff.c.
libata: Grand renaming.
Clean up drivers/ata/Kconfig a bit.
[PATCH] CONFIG_PM=n slim: drivers/scsi/sata_sil*
[PATCH] sata_via: Add SATA support for vt8237a
[PATCH] libata: change path to libata in libata.tmpl
[PATCH] libata: s/CONFIG_SCSI_SATA/CONFIG_[S]ATA/g in pci/quirks.c
libata: Make sure drivers/ata is a separate Kconfig menu
[libata] ata_piix: add missing kfree()
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a33f806bbbaae6775e87459b1ec584c0 that just happened to be
next to unrelated changes in this update.
|
|
|
|
nlmsg_multicast now takes an extra allocation flag, so add it to
the use in the fibre channel transport class.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Conflicts:
include/linux/blkdev.h
Trivial merge to incorporate tag prototypes.
|
|
Key more of the domain validation settings off the inquiry data from
the disk (in particular, don't try IU or DT unless the disk claims to
support them.
Also add a new dv_in_progress flag to prevent recursive DV.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
structures
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This started as a PCI reference fixup but to do that I need to build it,
to build it I need to fix it and its full of 32bitisms and uglies.
It has been resurrected, I'm not sure if this is a thank you for the
work on the license stuff or punishment for some unknown misdeed however
8). I've also fixed a memory scribble in the init code.
One oddity - the changes from HZ * to constants are deliberate. Whoever
originally wrote the code (or cleaned it up) used HZ for a cycle timing
loop even though is not HZ related. I've put it back to the counts used
in the old days when the driver was most used.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn:
Until the system is stabilized, I am suggesting the enclosed
modification to prevent the driver from tickling the panic. Once sysfs
and friends are stabilized, the patch may be backed out. We have yet to
evaluate if we really want to relinquish existing Scsi Devices in any
case, holding on to them as configuration of arrays comes and goes makes
some sense as well. As a result, we have opted to pull the lines rather
than comment them in legacy.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn:
The only real difference between the rkt and rx platform modules is the
offset of the message registers. This patch recognizes this similarity
and simplifies the driver to reduce it's code footprint and to improve
maintainability by reducing the code duplication.
Visibly, the 'rkt.c' portion of this patch looks more complicated than
it really is. View it as retaining the rkt-only specifics of the
interface.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn:
I am placing this functionality into an insmod parameter. Normally the physical
components are exported to sg, and are blocked from showing up in sd.
Note that the pass-through I/O path via the driver through the Firmware to the
physical disks is not an optimized path, the card is designed for Hardware
RAID, elevator sorting and caching. This should not be used as a means for
utilizing the aacraid based controllers as a generic scsi/SATA/SAS controller,
performance should suck by a few percentage points, any RAID meta-data on the
drives will confuse the controller about who owns the drives and there is a
high risk of destroying content in both directions. Unreliable and for
experimentation or strange controlled circumstances only.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn:
Basically cleanup, nothing here will have an affect. Adjusting some
error codes, removing superfluous definitions and code fragments.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* git://git.infradead.org/mtd-2.6:
[MTD] Whitespace cleanup in SSFDC driver.
[MTD] SSFDC translation layer minor cleanup
[MTD] Fix dependencies with CONFIG_MTD=m
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (353 commits)
[IPV6] ADDRCONF: Mobile IPv6 Home Address support.
[IPV6] ADDRCONF: Allow non-DAD'able addresses.
[IPV6] NDISC: Fix is_router flag setting.
[IPV6] ADDRCONF: Convert addrconf_lock to RCU.
[IPV6] NDISC: Add proxy_ndp sysctl.
[IPV6] NDISC: Set per-entry is_router flag in Proxy NA.
[IPV6] NDISC: Avoid updating neighbor cache for proxied address in receiving NA.
[IPV6]: Don't forward packets to proxied link-local address.
[IPV6] NDISC: Handle NDP messages to proxied addresses.
[NETFILTER]: PPTP conntrack: fix another GRE keymap leak
[NETFILTER]: PPTP conntrack: fix GRE keymap leak
[NETFILTER]: PPTP conntrack: fix PPTP_IN_CALL message types
[NETFILTER]: PPTP conntrack: check call ID before changing state
[NETFILTER]: PPTP conntrack: clean up debugging cruft
[NETFILTER]: PPTP conntrack: consolidate header parsing
[NETFILTER]: PPTP conntrack: consolidate header size checks
[NETFILTER]: PPTP conntrack: simplify expectation handling
[NETFILTER]: PPTP conntrack: remove unnecessary cid/pcid header pointers
[NETFILTER]: PPTP conntrack: fix header definitions
[NETFILTER]: PPTP conntrack: remove more dead code
...
|
|
Fix the fix ... One of my previous fixes introduced removal of all fsf
requests in zfcp's eh_host_reset_handler. But this must not happen
before qdio queues are shut down. So, I revert the changes of
zfcp_scsi_eh_host_reset_handler.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This instance will be used whenever a timer is needed for
a request by zfcp.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
zfcp's eh_abort_handler used the wrong request ID to
identify the request to be aborted. The bug was introduced
with commit fea9d6c7bcd8ff1d60ff74f27ba483b3820b18a3
for improved management of request IDs. The bug is
fixed with this patch.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Create private slab caches in order to guarantee proper alignment of
data structures that get passed to hardware.
Sidenote: with this patch slab cache debugging will finally work on s390
(at least no known problems left).
Furthermore this patch does some minor cleanups:
- store ptr for transport template in struct zfcp_data
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Compile fix ups and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Remove unused zfcp_ccw_unregister function (leftover from zfcp's
module_exit era).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Some cards need to pause the sequencer before the SBLKCTL register is
touched. This fixes a PCI related oops seen on powerpc macs with this
card caused by trying to ascertain the bus signalling before beginning
domain validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
For cards that don't support LVD, checking the SBLKCTL register to
determine the bus singalling doesn't work. So, check that the card
supports LVD first (AHC_ULTRA2) before checking the register.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
See http://www.torque.net/sg/sdebug26.html for more
information on the scsi_debug driver.
ChangeLog:
- add 'vpd_use_hostno' parameter to allow simulated hosts
to see the same set of targets (and luns). For testing
multipath software.
- add 'fake_rw' parameter to ignore the data in READ and
WRITE commands
- add support for log subpages (new in SPC-4)
- yield appropriate block descriptor for MODE SENSE
commands (only for pdt=0 (i.e. disks))
- REQUEST SENSE response no longer shows the stopped
power condition (SAT changed to agree with SPC-3)
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Conflicts:
drivers/scsi/iscsi_tcp.c
drivers/scsi/iscsi_tcp.h
Pretty horrible merge between crypto hash consolidation
and crypto_digest_...->crypto_hash_... conversion
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
annotated, fixed a roothole in ->write(). Dereferencing user-supplied pointer
is a Bad Idea(tm)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
indirect chains of includes are arch-specific and can't
be relied upon... (hell, even attempt to build it for
itanic would trigger vmalloc.h ones; err.h triggers
on e.g. alpha).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Check copy_to_user() return value in drivers/scsi/megaraid.c::megadev_ioctl()
This gets rid of this little warning:
drivers/scsi/megaraid.c:3661: warning: ignoring return value of 'copy_to_user', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix this driver not to use a static two element host array instead use
a list. This should fix panic on multiple eject reinsert of the
pcmcia version of this device.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch removes the reliance on FLASH Manufacture IDs for validation.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Says akpm: ' - search for "( " and " )", fix.'
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Don't include <linux/config.h>.
Don't say 'MB' where you mean 'MiB'.
Don't allocate 512 bytes on the stack.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
CMDLINEPARTS shouldn't be selectable, and neither should SSFDC, which
can be a tristate anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Rework AGPv3 modesetting fallback.
[AGPGART] Add suspend callback for i965
[AGPGART] Fix number of aperture sizes in 830 gart structs.
[AGPGART] Intel 965 Express support.
[AGPGART] agp.h: constify struct agp_bridge_data::version
[AGPGART] const'ify VIA AGP PCI table.
[AGPGART] CONFIG_PM=n slim: drivers/char/agp/intel-agp.c
[AGPGART] CONFIG_PM=n slim: drivers/char/agp/efficeon-agp.c
[AGPGART] Const'ify the agpgart driver version.
[AGPGART] remove private page protection map
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] sw_any_bug_dmi_table can be used on resume, so it isn't initdata
[CPUFREQ] Fix some more CPU hotplug locking.
[CPUFREQ] Workaround for BIOS bug in software coordination of frequency
[CPUFREQ] Longhaul - Add voltage scaling to driver
[CPUFREQ] Fix sparse warning in ondemand
[CPUFREQ] make drivers/cpufreq/cpufreq_ondemand.c:powersave_bias_target() static
[CPUFREQ] Longhaul - Add ignore_latency option
[CPUFREQ] Longhaul - Disable arbiter
[CPUFREQ][2/2] ondemand: updated add powersave_bias tunable
[CPUFREQ][1/2] ondemand: updated tune for hardware coordination
[CPUFREQ] Fix typo.
|
|
missing le16_to_cpu()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
