aboutsummaryrefslogtreecommitdiff
path: root/include/asm-arm
AgeCommit message (Collapse)Author
2008-04-19[ARM] 4948/1: magician: use htc-egpio to drive the GPIO/IRQ expander CPLDPhilipp Zabel
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] 4943/2: magician: fix magician.h GPIO header includesPhilipp Zabel
PXA GPIO definitions were split from pxa-regs.h into pxa2xx-gpio.h. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] 4867/1: Adds flash, udc, mci support for gumstix F boardsJaya Kumar
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are: - Steve Sakoman as maintainer - cleanup for udc and mci setup Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: remove keypad register definitions from pxa-regs.heric miao
Keypad registers are now fully defined within pxa27x-keypad.c, no need to keep those definitions in pxa-regs.h Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info()eric miao
also update the clk definitions in pxa27x and pxa3xx. Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}eric miao
Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}eric miao
Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.heric miao
two reasons: 1. GPIO namings and their mode definitions are conceptually not part of the PXA register definitions 2. this is actually a temporary move in the transition of PXA2xx to use MFP-alike APIs (as what PXA3xx is now doing), so that legacy code will still work and new code can be added in step by step Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into oneeric miao
This makes the code better organized and simplified a bit. The change will lose a bit of performance when performing IRQ ack/mask/unmask,but that's not too much after checking the result binary. This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by carefully not to access those pxa{27x,3xx} specific registers, this is done by keeping an internal IRQ number variable. The pxa-regs.h is also modified so registers for IRQ > PXA_IRQ(31) are made public even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake) The incorrect assumption in the original code that internal irq starts from 0 is also corrected by comparing with PXA_IRQ(0). "struct sys_device" for the IRQ are reduced into one single device on pxa{27x,3xx}. Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] 4868/1: Enhance pxa270 GPIO definitionsRobert Jarzmik
Enhanced GPIO alternate functions descriptions, taken from Intel PXA270 Developers Manual. Signed-off-by: Robert Jarzmik <rjarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] 4830/1: Add support for the CLK_POUT pin on PXA3xx CPUsMark Brown
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19[ARM] 4852/1: Add timerfd_create, timerfd_settime and timerfd_gettime ↵Uwe Kleine-König
syscall entries Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-18RealView: Add uncompressing support for PB1176Catalin Marinas
This patch adds the UART0 base address detection in uncompress.h. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Base support for the PB1176 platformBahadir Balban
This patch adds the base files for the PB1176 platform support. Signed-off-by: Bahadir Balban <bahadir.balban@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Add uncompressing support to PB11MPCoreCatalin Marinas
This patch adds the UART address detection in uncompress.h for the PB11MPCore platform. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Base support for the PB11MPCore platformBahadir Balban
This patch adds the base files for the PB11MPCore platform support. Signed-off-by: Bahadir Balban <bahadir.balban@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Change the IO_ADDRESS macroCatalin Marinas
This patch changes the IO_ADDRESS macro for the RealView platforms to accomodate a wider range of physical addresses on PB11MPCore. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move more device address definitions to board-eb.hCatalin Marinas
The upcoming PB11MPCore and PB1176 have different memory maps and some of the definitions in platform.h are no longer common. This patch moves them to the board-eb.h file and updates their usage in realview_eb.c. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move the UART definitions to EB specific filesCatalin Marinas
Since the PB1176 has different UART base addresses, this patch moves the definitions form platorm.h to board-eb.h. It also modifies uncompress.h to detect the platform type at run-time. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move the timer definitions into the EB specific filesCatalin Marinas
This patch moves the timer definitions from platform.h into board-eb.h as they are different on PB11MPCore and PB1176. It also adds timerX_va_base variables in core.c which are set by the realview_eb_timer_init function before invoking realview_timer_init. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move the flash definitions out of platform.hCatalin Marinas
This patch moves the patch definitions into board-eb.h and realview_eb.c (from core.c) as they are different on the PB11MPCore and PB1176 platforms. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move the EB GIC definitions to the board fileCatalin Marinas
This is in preparation for the RealView PB11MPCore and PB1176 patches which have different base addresses for the GIC. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18RealView: Move the SCU initialisation out of __v6_setupCatalin Marinas
This patch moves the SCU initialisation from __v6_setup to the smp_prepare_cpus() function as it relies on platform-specific settings. Changes to get_core_count() are mainly for allowing cleaner code with the upcoming PB11MPCore patches. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18Add a prefetch abort handlerPaul Brook
This patch adds a prefetch abort handler similar to the data abort one and renames the latter for consistency. Initial implementation by Paul Brook with some renaming by Catalin Marinas. Signed-off-by: Paul Brook <paul@codesourcery.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18ARMv7: Add support for the ThumbEE state saving/restoringCatalin Marinas
This patch adds the detection and handling of the ThumbEE extension on ARMv7 CPUs. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18MMC: OMAP: Introduce new multislot structure and change driver to use itJuha Yrjola
Introduce new MMC multislot structure and change driver to use it. Note that MMC clocking is now enabled in mmc_omap_select_slot() and disabled in mmc_omap_release_slot(). Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (58 commits) ide: remove ide_init_default_irq() macro ide: move default IDE ports setup to ide_generic host driver ide: remove obsoleted "idex=noprobe" kernel parameter (take 2) ide: remove needless hwif->irq check from ide_hwif_configure() ide: init hwif->{io_ports,irq} explicitly in legacy VLB host drivers ide: limit legacy VLB host drivers to alpha, x86 and mips cmd640: init hwif->{io_ports,irq} explicitly cmd640: cleanup setup_device_ptrs() ide: add ide-4drives host driver (take 3) ide: remove ppc ifdef from init_ide_data() ide: remove ide_default_io_ctl() macro ide: remove CONFIG_IDE_ARCH_OBSOLETE_INIT ide: add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS (take 2) ppc/pmac: remove no longer needed IDE quirk ppc: don't include <linux/ide.h> ppc: remove ppc_ide_md ppc/pplus: remove ppc_ide_md.ide_init_hwif hook ppc/sandpoint: remove ppc_ide_md hooks ppc/lopec: remove ppc_ide_md hooks ppc/mpc8xx: remove ppc_ide_md hooks ...
2008-04-18Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: dmaengine: ack to flags: make use of the unused bits in the 'ack' field iop-adma: remove the workaround for missed interrupts on iop3xx async_tx: kill ->device_dependency_added async_tx: fix multiple dependency submission fsldma: Split the MPC83xx event from MPC85xx and refine irq codes. fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
2008-04-18ide: remove ide_default_io_ctl() macroBartlomiej Zolnierkiewicz
It is always == '((base) + 0x206)' if CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=y and it is not needed otherwise (arm, blackfin, parisc, ppc64, sh, sparc[64]). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-17iop-adma: remove the workaround for missed interrupts on iop3xxDan Williams
This workaround was covering the dependency submission bug in async_tx. Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17[ARM] 4883/1: Adds some missing gpio defines for S3C2410Davide Rizzo
This is a small addition of forgotten defines to regs-gpio.h include file for the Samsung S3C2410 ARM9 SoC Signed-off-by: Davide Rizzo <davide@elpa.it> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4987/1: S3C24XX: Ensure watchdog reset initiated from cached code.Ben Dooks
There seems to be some problem with at-least the S3C2440 and bus traffic during an reset. It is unlikely, but still possible that the system will hang in such a way that the watchdog cannot get the system out of the state it is in. Change to making the code that calls the watchdog reset run from cached memory so that instruction fetches have quiesced before the watchdog fires. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4985/1: S3C2412: Fix ARMDIVN name in CLKDIVN definition.Ben Dooks
Fix the name of the S3C2412_CLKDIVN_ARMDIVN define. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4983/1: S3C2412: Add initial memory controller registersBen Dooks
Add initial defines for the S3C2412's memory controller registers. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4887/1: i.MXC family: Separate current platform codeRobert Schwebel
From: Juergen Beisert <j.beisert@pengutronix.de> This patch separates the current code into i.MX2 and i.MX3 and modifies the Kconfig files to reflect this separation in the menus. Things happend since last review: - make i.MX3 compile again - fix some structure names to be conform with all the shared/common sources from i.MX1/i.MX2 Previous changes: - stay conform to other Kconfig files (note from Russell King) Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4981/1: [KS8695] Simple LED driverAndrew Victor
Simple gpio-connected LED driver for KS8695 platforms. (Based on old AT91 LED driver) Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17Generic semaphore implementationMatthew Wilcox
Semaphores are no longer performance-critical, so a generic C implementation is better for maintainability, debuggability and extensibility. Thanks to Peter Zijlstra for fixing the lockdep warning. Thanks to Harvey Harrison for pointing out that the unlikely() was unnecessary. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Acked-by: Ingo Molnar <mingo@elte.hu>
2008-04-15spi: spi_s3c24xx must initialize num_chipselectBen Dooks
The SPI core now expects num_chipselect to be set correctly as due to added checks on the chip being selected before an transfer is allowed. This patch adds a num_cs field to the platform data which needs to be set correctly before adding the SPI platform device. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-14ARM: OMAP2: New DPLL clock frameworkRoman Tereshonkov
These changes is the result of the discussion with Paul Walmsley. His ideas are included into this patch. Remove DPLL output divider handling from DPLLs and CLKOUTX2 clocks, and place it into specific DPLL output divider clocks (e.g., dpll3_m2_clk). omap2_get_dpll_rate() now returns the correct DPLL rate, as represented by the DPLL's CLKOUT output. Also add MPU and IVA2 subsystem clocks, along with high-frequency bypass support. Add support for DPLLs function in locked and bypass clock modes. Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Add 34xx clocksPaul Walmsley
This patch defines 34xx clocks. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Change 24xx to use shared clock code and new reg accessPaul Walmsley
This patch changes 24xx to use shared clock code and new register access. Note that patch adds some temporary OLD_CK defines to keep patch more readable. These temporary defines will be removed in the next patch. Also not all clocks are changed in this patch to limit the size. Also, the patch fixes few incorrect clock defines in clock24xx.h. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Change 24xx to use new register accessPaul Walmsley
This patch changes 24xx to use new register access, except for clock framework. Clock framework register access will get updates in the next patch. Note that board-*.c files change GPMC (General Purpose Memory Controller) access to use gpmc_cs_write_reg() instead of accessing the registers directly. The code also uses gpmc_fck instead of it's parent clock core_l3_ck for GPMC clock. The H4 board file also adds h4_init_flash() function, which specify the flash start and end addresses. Also note that sleep.S removes some unused registers addresses. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Add common register access for 24xx and 34xxPaul Walmsley
This patch adds common register access for 24xx and 34xx power and clock management in order to share code between 24xx and 34xx. Only change USB platform init code to use new register access, other access will be changed in later patches. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Clean-up mux codeTony Lindgren
Misc clean-up for the mux code and remove some unnecessary ifdefs. Patch changes debug function so it can be used on both 24xx and 34xx. Changes are mostly for omap2, but patch also cleans up some omap1 and common mux code. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP2: Add new pin multiplexing configurationsTony Lindgren
Add new pin multiplexing configurations Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP: Allow registering pin mux functionTony Lindgren
This patch changes pin multiplexing init to allow registering custom function. The omap_cfg_reg() func will be split into omap processor specific functions in later patch. This is done to make adding omap3 pin multiplexing easier. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP: Use gpiolib with tps65010 for OSK 5912David Brownell
Convert OSK board to use new tps65010 gpiolib support. This includes moving its LED support from leds-osk to gpio-leds, giving more trigger options and a net platform code shrink. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14ARM: OMAP: Use gpiolibDavid Brownell
Update OMAP to use the new GPIO implementation framework. This is just a quick'n'dirty update ... more code could now be removed, ideally as part of cleaning up the entire OMAP GPIO infrastructure ... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-10[ARM] 4962/1: Introduce standard gpio interface for Scoop2.Dmitry Baryshkov
This deprecates old set/reset_scoop_gpio interfacein favour of support for generic gpio interface. It requires gpiolib, so it depends on the previous patch (gpiolib for SA-1100). Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-10[ARM] 4961/1: gpiolib support for SA-1100 architectureDmitry Baryshkov
This adds gpiolib support for the SA-1100 arch: - Move all GPIO API functions from generic.c into gpio.c - Convert all gpio functions into gpiolib callbacks. Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>