| Age | Commit message (Collapse) | Author |
|---|
|
Things were scattered all over the place, split between
SMP and non-SMP.
Unify it all so that dyntick support is easier to add.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the first in a series of cleanups that will hopefully
allow a seamless attempt at using the generic IRQ handling
infrastructure in the Linux kernel.
Define PIL_DEVICE_IRQ and vector all device interrupts through
there.
Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector
the timer interrupt directly to a specific handler since the
timer interrupt is the only event that will be signaled on
PIL 14.
The irq_worklist is now in the per-cpu trap_block[].
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set, but never used.
We used to use this for dynamic IRQ retargetting, but that
code died a long time ago.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use the real hardware processor ID when
targetting interrupts, not the "define to 0" thing
the uniprocessor build gives us.
Also, fill in the Node-ID and Agent-ID fields properly
on sun4u/Safari.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sibling cpu bringup is extremely fragile. We can only
perform the most basic calls until we take over the trap
table from the firmware/hypervisor on the new cpu.
This means no accesses to %g4, %g5, %g6 since those can't be
TLB translated without our trap handlers.
In order to achieve this:
1) Change sun4v_init_mondo_queues() so that it can operate in
several modes.
It can allocate the queues, or install them in the current
processor, or both.
The boot cpu does both in it's call early on.
Later, the boot cpu allocates the sibling cpu queue, starts
the sibling cpu, then the sibling cpu loads them in.
2) init_cur_cpu_trap() is changed to take the current_thread_info()
as an argument instead of reading %g6 directly on the current
cpu.
3) Create a trampoline stack for the sibling cpus. We do our basic
kernel calls using this stack, which is locked into the kernel
image, then go to our proper thread stack after taking over the
trap table.
4) While we are in this delicate startup state, we put 0xdeadbeef
into %g4/%g5/%g6 in order to catch accidental accesses.
5) On the final prom_set_trap_table*() call, we put &init_thread_union
into %g6. This is a hack to make prom_world(0) work. All that
wants to do is restore the %asi register using
get_thread_current_ds().
Longer term we should just do the OBP calls to set the trap table by
hand just like we do for everything else. This would avoid that silly
prom_world(0) issue, then we can remove the init_thread_union hack.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is where the virtual address of the fault status
area belongs.
To set it up we don't make a hypervisor call, instead
we call OBP's SUNW,set-trap-table with the real address
of the fault status area as the second argument. And
right before that call we write the virtual address into
ASI_SCRATCHPAD vaddr 0x0.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Technically the hypervisor call supports sending in a list
of all cpus to get the cross-call, but I only pass in one
cpu at a time for now.
The multi-cpu support is there, just ifdef'd out so it's easy to
enable or delete it later.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sun4v has 4 interrupt queues: cpu, device, resumable errors,
and non-resumable errors. A set of head/tail offset pointers
help maintain a work queue in physical memory. The entries
are 64-bytes in size.
Each queue is allocated then registered with the hypervisor
as we bring cpus up.
The two error queues each get a kernel side buffer that we
use to quickly empty the main interrupt queue before we
call up to C code to log the event and possibly take evasive
action.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, correct TRAP_PER_CPU_FAULT_INFO define, it should be
0x40 not 0x20.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the expansion of __GET_CPUID() on SMP.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Things are a little tricky because, unlike sun4u, we have
to:
1) do a hypervisor trap to do the TLB load.
2) do the TSB lookup calculations by hand
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we're just switching between different alternate global
sets, nop it out on sun4v. Also, get rid of all of the
alternate global save/restore in the OBP CIF trampoline code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of setting/clearing PSTATE_AG we have to change
the %gl register value on sun4v.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This, as well as making the code cleaner, allows a simplification in
the TSB miss handling path.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On uniprocessor, it's always zero for optimize that.
On SMP, the jmpl to the stub kills the return address stack in the cpu
branch prediction logic, so expand the code sequence inline and use a
code patching section to fix things up. This also always better and
explicit register selection, which will be taken advantage of in a
future changeset.
The hard_smp_processor_id() function is big, so do not inline it.
Fix up tests for Jalapeno to also test for Serrano chips too. These
tests want "jbus Ultra-IIIi" cases to match, so that is what we should
test for.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we use %g5 itself as a temporary, it can get clobbered
if we take an interrupt mid-stream and thus cause end up with
the final %g5 value too early as a result of rtrap processing.
Set %g5 at the very end, atomically, to avoid this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used, and move extern declaration to a header file.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UltraSPARC has special sets of global registers which are switched to
for certain trap types. There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.
For what seems like forever we've hard coded the values in some of
these trap registers. Some examples include:
1) Interrupt Vector global %g6 holds current processors interrupt
work struct where received interrupts are managed for IRQ handler
dispatch.
2) MMU global %g7 holds the base of the page tables of the currently
active address space.
3) Alternate global %g6 held the current_thread_info() value.
Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation. Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.
We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.
The implementation is pretty straight forward. One tricky bit is
getting the current processor ID as that is different on different cpu
variants. We use a stub with a fancy calling convention which we
patch at boot time. The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1. The cpu
number is left in %g6. This stub can be invoked by using the
__GET_CPUID macro.
We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables. The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.
TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6. It also uses
__GET_CPUID and clobbers %g1.
Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.
Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking a nod from the powerpc port.
With the per-cpu caching of both the page allocator and SLAB, the
pgtable quicklist scheme becomes relatively silly and primitive.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike the virtual page tables, the new TSB scheme does not
require this ugly hack.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can put the __softirq_pending mask in the cpudata,
no need for the silly NR_CPUS array in kernel/softirq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
