aboutsummaryrefslogtreecommitdiff
path: root/include/linux/libata.h
AgeCommit message (Collapse)Author
2008-12-01libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQTejun Heo
Some recent Seagate harddrives have firmware bug which causes FLUSH CACHE to timeout under certain circumstances if NCQ is being used. This can be worked around by disabling NCQ and fixed by updating the firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these devices. The wiki page has been updated to contain information on this issue. http://ata.wiki.kernel.org/index.php/Known_issues Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-10libata: revert convert-to-block-tagging patchesTejun Heo
This patch reverts the following three commits which convert libata to use block layer tagging. 43a49cbdf31e812c0d8f553d433b09b421f5d52c e013e13bf605b9e6b702adffbe2853cfc60e7806 2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e Although using block layer tagging is the right direction, due to the tight coupling among tag number, data structure allocation and hardware command slot allocation, libata doesn't work correctly with the current conversion. The biggest problem is guaranteeing that tag 0 is always used for non-NCQ commands. Due to the way blk-tag is implemented and how SCSI starts and finishes requests, such guarantee can't be made. I'm not sure whether this would actually break any low level driver but it doesn't look like a good idea to break such assumption given the frailty of ATA controllers. So, for the time being, keep using the old dumb in-libata qc allocation. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jens Axobe <jens.axboe@oracle.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-04libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply itTejun Heo
libata always uses PIO for ATAPI commands when the number of bytes to transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes PIO transfers. Implement a horkage to skip the mod16 check and apply it to the quantum device. This is reported by John Clark in the following thread. http://thread.gmane.org/gmane.linux.ide/34748 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: John Clark <clarkjc@runbox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31libata: add whitelist for devices with known good pata-sata bridgesJens Axboe
libata currently imposes a UDMA5 max transfer rate and 200 sector max transfer size for SATA devices that sit behind a pata-sata bridge. Lots of devices have known good bridges that don't need this limit applied. The MTRON SSD disks are such devices. Transfer rates are increased by 20-30% with the restriction removed. So add a "blacklist" entry for the MTRON devices, with a flag indicating that the bridge is known good. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-23libata: switch to using block layer tagging supportJens Axboe
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding a free tag to use. Instead of fixing that up, convert libata to using block layer tagging - gets rid of code in libata, and is also much faster. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-22libata: transfer EHI control flags to slave ehc.iTejun Heo
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior of EH. As only the master link is visible outside EH, these flags are set only for the master link although they should also apply to the slave link, which causes spurious EH messages during probe and suspend/resume. This patch transfers those two flags to slave ehc.i before performing slave autopsy and reporting. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: reorder ata_device to remove 8 bytes of padding on 64 bitsRichard Kennedy
reduce size by 8 bytes from 1160 to 1152 allowing it to fit in 1 fewer cachelines. Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: Implement disk shock protection supportElias Oltmanns
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD FEATURE as specified in ATA-7 is issued to the device and processing of the request queue is stopped thereafter until the specified timeout expires or user space asks to resume normal operation. This is supposed to prevent the heads of a hard drive from accidentally crashing onto the platter when a heavy shock is anticipated (like a falling laptop expected to hit the floor). In fact, the whole port stops processing commands until the timeout has expired in order to avoid any resets due to failed commands on another device. Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: implement slave_linkTejun Heo
Explanation taken from the comment of ata_slave_link_init(). In libata, a port contains links and a link contains devices. There is single host link but if a PMP is attached to it, there can be multiple fan-out links. On SATA, there's usually a single device connected to a link but PATA and SATA controllers emulating TF based interface can have two - master and slave. However, there are a few controllers which don't fit into this abstraction too well - SATA controllers which emulate TF interface with both master and slave devices but also have separate SCR register sets for each device. These controllers need separate links for physical link handling (e.g. onlineness, link speed) but should be treated like a traditional M/S controller for everything else (e.g. command issue, softreset). slave_link is libata's way of handling this class of controllers without impacting core layer too much. For anything other than physical link handling, the default host link is used for both master and slave. For physical link handling, separate @ap->slave_link is used. All dirty details are implemented inside libata core layer. From LLD's POV, the only difference is that prereset, hardreset and postreset are called once more for the slave link, so the reset sequence looks like the following. prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) -> softreset(M) -> postreset(M) -> postreset(S) Note that softreset is called only for the master. Softreset resets both M/S by definition, so SRST on master should handle both (the standard method will work just fine). As slave_link excludes PMP support and only code paths which deal with the attributes of physical link are affected, all the changes are localized to libata.h, libata-core.c and libata-eh.c. * ata_is_host_link() updated so that slave_link is considered as host link too. * iterator extended to iterate over the slave_link when using the underbarred version. * force param handling updated such that devno 16 is mapped to the slave link/device. * ata_link_on/offline() updated to return the combined result from master and slave link. ata_phys_link_on/offline() are the direct versions. * EH autopsy and report are performed separately for master slave links. Reset is udpated to implement the above described reset sequence. Except for reset update, most changes are minor, many of them just modifying dev->link to ata_dev_phys_link(dev) or using phys online test instead. After this update, LLDs can take full advantage of per-dev SCR registers by simply turning on slave link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: misc updates to prepare for slave linkTejun Heo
* Add ATA_EH_ALL_ACTIONS. * Make sata_link_{on|off}_line() return bool instead of int. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: reimplement link iteratorTejun Heo
Implement __ata_port_next_link() and reimplement __ata_port_for_each_link() and ata_port_for_each_link() using it. This removes relatively large inlined code and makes iteration easier to extend. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29libata: make SCR access ops per-linkTejun Heo
Logically, SCR access ops should take @link; however, there was no compelling reason to convert all SCR access ops when adding @link abstraction as there's one-to-one mapping between a port and a non-PMP link. However, that assumption won't hold anymore with the scheduled addition of slave link. Make SCR access ops per-link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22libata: Fix a large collection of DMA mode mismatchesAlan Cox
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while the core code uses 0xFF. This turns out to have other consequences such as code doing >= XFER_UDMA_0 also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect set_dma_mode, although some drivers call back into their own set mode code from other points. Having been through the drivers I've added helpers for using_udma/using_mwdma dma_enabled so that people don't open code ranges that may change (eg if UDMA8 appears somewhere) Thanks to David for the initial bits [and added fix for pata_oldpiix from and signed-off-by Dave Mueller <dave.mueller@gmx.ch> -jg] Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22libata: restore SControl on detachTejun Heo
Save SControl during probing and restore it on detach. This prevents adjustments made by libata drivers to seep into the next driver which gets attached (be it a libata one or not). It's not clear whether SControl also needs to be restored on suspend. The next system to have control (ACPI or kexec'd kernel) would probably like to see the original SControl value but there's no guarantee that a link is gonna keep working after SControl is adjusted without a reset and adding a reset and modified recovery cycle soley for this is an overkill. For now, do it only for detach. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-22libata: implement no[hs]rst force paramsTejun Heo
Implement force params nohrst, nosrst and norst. This is to work around reset related problems and ease debugging. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31pata_it821x: Driver updates and reworkingAlan Cox
- Add support for the RDC 1010 variant - Rework the core library to have a read_id method. This allows the hacky bits of it821x to go and prepares us for pata_hd - Switch from WARN to BUG in ata_id_string as it will reboot if you get it wrong so WARN won't be seen - Allow the issue of command 0xFC on the 821x. This is needed to query rebuild status. - Tidy up printk formatting - Do more ident rewriting on RAID volumes to handle firmware provided ident data which is rather wonky - Report the firmware revision and device layout in RAID mode - Don't try and disable raid on the 8211 or RDC - they don't have the relevant bits Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31libata.h: replace __FUNCTION__ with __func__Alexander Beregalov
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14libata/ahci: enclosure management supportKristen Carlson Accardi
Add Enclosure Management support to libata and ahci. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14libata: improve EH internal command timeout handlingTejun Heo
ATA_TMOUT_INTERNAL which was 30secs were used for all internal commands which is way too long when something goes wrong. This patch implements command type based stepped timeouts. Different command types can use different timeouts and each command type can use different timeout values after timeouts. ie. the initial timeout is set to a value which should cover most of the cases but not too long so that run away cases don't delay things too much. After the first try times out, the second try can use longer timeout and if that one times out too, it can go for full 30sec timeout. IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s - 10s timeouts. This patch significantly cuts down the needed time to handle failure cases while still allowing libata to work with nut job devices through retries. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14libata: improve EH retry delay handlingTejun Heo
EH retries were delayed by 5 seconds to ensure that resets don't occur back-to-back. However, this 5 second delay is superflous or excessive in many cases. For example, after IDENTIFY times out, there's no reason to wait five more seconds before retrying. This patch adds ehc->last_reset timestamp and record the timestamp for the last reset trial or success and uses it to space resets by ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec sleeps. As this change makes inter-try waits often shorter and they're redundant in nature, this patch also removes the "retrying..." messages. While at it, convert explicit rounding up division to DIV_ROUND_UP(). This change speeds up EH in many cases w/o sacrificing robustness. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14libata: consistently use msecs for time durationsTejun Heo
libata has been using mix of jiffies and msecs for time druations. This is getting confusing. As writing sub HZ values in jiffies is PITA and msecs_to_jiffies() can't be used as initializer, unify unit for all time durations to msecs. So, durations are in msecs and deadlines are in jiffies. ata_deadline() is added to compute deadline from a start time and duration in msecs. While at it, drop now superflous _msec suffix from arguments and rename @timeout to @deadline if it represents a fixed point in time rather than duration. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctlAlan Cox
- Make ata_sff_altstatus private so nobody uses it by mistake - Drop the 400nS delay from it Add ata_sff_irq_status - encapsulates the IRQ check logic This function keeps the existing behaviour for altstatus using devices. I actually suspect the logic was wrong before the changes but -rc isn't the time to play with that ata_sff_sync - ensure writes hit the device Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so that we can fix the nasty delay this causes on most systems. - ata_sff_pause - 400nS delay Ensure the command hit the device and delay 400nS - ata_sff_dma_pause Ensure the I/O hit the device and enforce an HDMA1:0 transition delay. Requires altstatus register exists, BUG if not so we don't risk corruption in MWDMA modes. (UDMA the checksum will save your backside in theory) The only other complication then is devices with their own handlers. rb532 can use dma_pause but scc needs to access its own altstatus register for internal errata workarounds so directly call the drivers own altstatus function. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04libata: kill unused constantsTejun Heo
Kill a few unused constants. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19libata: ignore SIMG4726 config pseudo deviceTejun Heo
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it happy but no even this doesn't work under certain configurations and it's not like we can do anything useful with the cofig device anyway. Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for the config device. This makes the device completely ignored by libata. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19libata: increase PMP register access timeout to 3sTejun Heo
This timeout was set low because previously PMP register access was done via polling and register access timeouts could stack up. This is no longer the case. One timeout will make all following accesses fail immediately. In rare cases both marvell and SIMG PMPs need almost a second. Bump it to 3s. While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to SCR access. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19ata: remove FIT() macroHarvey Harrison
Use the kernel-provided clamp_val() macro. FIT was always applied to a member of struct ata_timing (unsigned short) and two constants. clamp_val will not cast to short anymore. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-09[libata] revert new check-ready Status register logicJeff Garzik
This behavior differs across multiple controllers, so we cannot use common logic for all controllers. Revert back to the basic common behavior, and specific drivers will be updated from here to take into account the unusual Status return values. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06libata: export ata_eh_analyze_ncq_errorMark Lord
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv, as suggested by Tejun. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06libata: improve post-reset device ready testTejun Heo
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that the device isn't ready yet. It looks like they use 0xff if device presence is detected but connection isn't established. 0x77 or 0x7f after connection is established and use the value from signature FIS after receiving it. This patch implements ata_check_ready(), which takes TF status value and determines whether the port is ready or not considering the above and other conditions, and use it in @check_ready() functions. This is safe as both 0x77 and 0x7f aren't valid ready status value even though they have BSY bit cleared. This fixes hot plug detection failures which can be triggered with certain drives if they aren't already spun up when the data connector is hot plugged. Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with eight drives from all major vendors. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29[libata] linux/libata.h: reorganize ata_device struct members a bitJeff Garzik
Put the big stuff at the end, to prepare for upcoming changes (and also hopefully achieve nicer packing of remaining members). Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25make sata_print_link_status() staticAdrian Bunk
sata_print_link_status() can now become static. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-19SCSI: convert struct class_device to struct deviceTony Jones
It's big, but there doesn't seem to be a way to split it up smaller... Signed-off-by: Tony Jones <tonyj@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Cc: Roland Dreier <rolandd@cisco.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-17libata: make PMP support optionalTejun Heo
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out libata-pmp.c if it isn't set. PMP helpers return constant values if PMP support is not enabled and PMP declarations alias non-PMP counterparts. This makes the compiler to leave out PMP related part out and LLDs to use non-PMP counterparts automatically. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement PMP helpersTejun Heo
Implement helpers to test whether PMP is supported, attached and determine pmp number to use when issuing SRST to a link. While at it, move ata_is_host_link() so that it's together with the two new PMP helpers. This change simplifies LLDs and helps making PMP support optional. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate PMP support code from core codeTejun Heo
Most of PMP support code is already in libata-pmp.c. All that are in libata-core.c are sata_pmp_port_ops and EXPORTs. Move them to libata-pmp.c. Also, collect PMP related prototypes and declarations in header files and move them right above of SFF stuff. This change is to make PMP support optional. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: make SFF support optionalTejun Heo
Now that SFF support is completely separated out from the core layer, it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c and data structures for SFF support are disabled. This saves good number of bytes for small systems. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: kill ata_noop_dev_select()Tejun Heo
Now that SFF assumptions are separated out from non-SFF reset sequence, port_ops->sff_dev_select() is no longer necessary for non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select initialization from base and other non-SFF port_ops. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: drop @finish_qc from ata_qc_complete_multiple()Tejun Heo
ata_qc_complete_multiple() took @finish_qc and called it on every qc before completing it. This was to give opportunity to update TF cache before ata_qc_complete() tries to fill result_tf. Now that result TF is a separate operation, this is no longer necessary. Update sata_sil24, which was the only user of this mechanism, such that it implements its own ops->qc_fill_rtf() and drop @finish_qc from ata_qc_complete_multiple(). Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: add qc_fill_rtf port operationTejun Heo
On command completion, ata_qc_complete() directly called ops->tf_read to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace hardcoded ops->tf_read usage. ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is implemented and set in ata_base_port_ops and other ops tables which don't inherit from ata_base_port_ops, so this patch doesn't introduce any behavior change. ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be called when a command finishes. As some non-SFF controllers don't have TF registers defined unless they're associated with in-flight commands, this limited operation makes life easier for those drivers and help lifting SFF assumptions from libata core layer. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: move PMP SCR access failure during reset to ata_eh_reset()Tejun Heo
If PMP fan-out reset fails and SCR isn't accessible, PMP should be reset. This used to be tested by sata_pmp_std_hardreset() and communicated to EH by -ERESTART. However, this logic is generic and doesn't really have much to do with specific hardreset implementation. This patch moves SCR access failure detection logic to ata_eh_reset() where it belongs. As this makes sata_pmp_std_hardreset() identical to sata_std_hardreset(), the function is killed and replaced with the standard method. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: clear SError after link resumeTejun Heo
SError used to be cleared in ->postreset. This has small hotplug race condition. If a device is plugged in after reset is complete but postreset hasn't run yet, its hotplug event gets lost when SError is cleared. This patch makes sata_link_resume() clear SError. This kills the race condition and makes a lot of sense as some PMP and host PHYs don't work properly without SError cleared. This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as they become identical to ata_std counterparts. It also simplifies sata_pmp_hardreset() and ahci_vt8251_hardreset(). Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use sata_std_hardreset()Tejun Heo
Implement sata_std_hardreset(), which simply wraps around sata_link_hardreset(). sata_std_hardreset() becomes new standard hardreset method for sata_port_ops and sata_sff_hardreset() moves from ata_base_port_ops to ata_sff_port_ops, which is where it really belongs. ata_is_builtin_hardreset() is added so that both ata_std_error_handler() and ata_sff_error_handler() skip both builtin hardresets if SCR isn't accessible. piix_sidpr_hardreset() in ata_piix.c is identical to sata_std_hardreset() in functionality and got replaced with the standard function. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: move generic hardreset code from sata_sff_hardreset() to ↵Tejun Heo
sata_link_hardreset() sata_sff_hardreset() contains link readiness wait logic which isn't SFF specific. Move that part into sata_link_hardreset(), which now takes two more parameters - @online and @check_ready. Both are optional. The former is out parameter for link onlineness after reset. The latter is used to wait for link readiness after hardreset. Users of sata_link_hardreset() is updated to use new funtionality and ahci_hardreset() is updated to use sata_link_hardreset() instead of sata_sff_hardreset(). This doesn't really cause any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_wait_ready() and implement ata_wait_after_reset()Tejun Heo
Factor out waiting logic (which is common to all ATA controllers) from ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes @check_ready function pointer and uses it to poll for readiness. This allows non-SFF controllers to use ata_wait_ready() to wait for link readiness. This patch also implements ata_wait_after_reset() - generic version of ata_sff_wait_after_reset() - using ata_wait_ready(). ata_sff_wait_ready() is reimplemented using ata_wait_ready() and ata_sff_check_ready(). Functionality remains the same. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: restructure SFF post-reset readiness waitsTejun Heo
Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_std_postreset() from ata_sff_postreset()Tejun Heo
Separate out generic ATA portion from ata_sff_postreset() into ata_std_postreset() and implement ata_sff_postreset() using the std version. ata_base_port_ops now has ata_std_postreset() for its postreset and ata_sff_port_ops overrides it to ata_sff_postreset(). This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma now specifies postreset to ata_sff_postreset() explicitly. sata_fsl and sata_sil24 now use ata_std_postreset() which makes no difference to them. ahci now calls ata_std_postreset() from its own postreset method, which causes no behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_std_prereset() from ata_sff_prereset()Tejun Heo
Separate out generic ATA portion from ata_sff_prereset() into ata_std_prereset() and implement ata_sff_prereset() using the std version. Waiting for device readiness is the only SFF specific part. ata_base_port_ops now has ata_std_prereset() for its prereset and ata_sff_port_ops overrides it to ata_sff_prereset(). This change can affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements its own prereset using ata_sff_prereset() and the rest has hardreset and thus are unaffected by this change. This change reflects real world situation. There is no generic way to wait for device readiness for non-SFF controllers and some of them don't have any mechanism for that. Non-sff drivers which don't have hardreset should wrap ata_std_prereset() and wait for device readiness itself but there's no such driver now and isn't likely to be popular in the future either. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: clean up port_ops->sff_irq_clear()Tejun Heo
->sff_irq_clear() is called only from SFF interrupt handler, so there is no reason to initialize it for non-SFF controllers. Also, ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF controllers. This patch kills ata_noop_irq_clear() and removes it from base port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff port_ops instead of bmdma port_ops. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF port opsTejun Heo
Add sff_ prefix to SFF specific port ops. This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames ops and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>