| Age | Commit message (Collapse) | Author |
|---|
|
This adds kerneldoc to the SPI framework. The "spi_driver" and
"spi_board_info" structs were previously not described.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The spidev driver doesn't currently expose all SPI communications modes to
userspace. This passes them all through to the driver.
Two of them are potentially troublesome, in the sense that they could cause
hardware conflicts on shared busses. It might be appropriate to add some
privilege checks for for those modes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Loopback mode is supported by various controllers. This mode can be
useful for testing, especially in conjunction with spidev driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pendown status from the PENIRQ pin is currently read only at the beginning
of a sample set. If the pen is lifted just after sampling has began then
sampled values become wrong.
This patch adds an optional platform penirq_recheck_delay attribute. If
non-zero, samples are only reported to the input subsystem if PENIRQ is
still active that long after the samples taken.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The ads7846 driver has support for filtering, but when the chip gets
deselected between samples this causes noise. This patch adds support
for an optional settling delay time, so that two consecutive samples
will be taken with the specified delay time apart. This ensures that
the chip won't be deselected, so the noise won't appear.
Filtering can still be done, but will have less work to do since each
time a new sample is taken the same delay applies.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new spi->mode bit: SPI_3WIRE, for chips where the SI and SO signals
are shared (and which are thus only half duplex). Update the LM70 driver
to require support for that hardware mode from the controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update two points in the SPI interface documentation:
- Update description of the "chip stays selected after message ends"
mode. In some cases it's required for correctness; it isn't just a
performance tweak. (Yes: to use this mode on mult-device busses, another
programming interface will be needed. One draft has been circulated
already.)
- Clarify spi_setup(), highlighting that callers must ensure that no
requests are queued (can't change configuration except between I/Os), and
that the device must be deselected when this returns (which is a key part
of why it's called during device init).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Various documentation updates for the SPI infrastructure, to clarify things
that may not have been clear, to cope with lack of editing, and fix
omissions.
Also, plug SPI into the kernel-api DocBook template, and fix all the
resulting glitches in document generation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a filesystem API for <linux/spi/spi.h> stack. The initial version of
this interface is purely synchronous.
dbrownell@users.sourceforge.net:
Cleaned up, bugfixed; much simplified; added preliminary documentation.
Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev.
Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting
groups of one or more transfers (each of which may be full duplex if
desired).
This is marked as EXPERIMENTAL with an explicit disclaimer that the API
(notably the ioctls) is subject to change.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for the Analog Devices Blackfin processor architecture, and
currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561
(Dual Core) devices, with a variety of development platforms including those
avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP,
BF561-EZKIT), and Bluetechnix! Tinyboards.
The Blackfin architecture was jointly developed by Intel and Analog Devices
Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in
December of 2000. Since then ADI has put this core into its Blackfin
processor family of devices. The Blackfin core has the advantages of a clean,
orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC
(Multiply/Accumulate), state-of-the-art signal processing engine and
single-instruction, multiple-data (SIMD) multimedia capabilities into a single
instruction-set architecture.
The Blackfin architecture, including the instruction set, is described by the
ADSP-BF53x/BF56x Blackfin Processor Programming Reference
http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf
The Blackfin processor is already supported by major releases of gcc, and
there are binary and source rpms/tarballs for many architectures at:
http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete
documentation, including "getting started" guides available at:
http://docs.blackfin.uclinux.org/ which provides links to the sources and
patches you will need in order to set up a cross-compiling environment for
bfin-linux-uclibc
This patch, as well as the other patches (toolchain, distribution,
uClibc) are actively supported by Analog Devices Inc, at:
http://blackfin.uclinux.org/
We have tested this on LTP, and our test plan (including pass/fails) can
be found at:
http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel
[m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files]
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Aubrey Li <aubrey.li@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a bug in the cleanup of an spi_bitbang bus.
The workqueue associated with the bus was destroyed before the call to
spi_unregister_master. That meant that spi devices on that bus would be
unable to do IO in their remove method. The shutdown flag should have been
able to prevent a segfault, but was never getting set. By waiting to
destroy the workqueue until after the master is unregistered, devices are
able to do IO in their remove methods. An added benefit is that neither
the shutdown flag nor a wait for the queue of messages to empty is needed.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is adds a simple SPI EEPROM driver, providing access to the EEPROM
through sysfs much like the I2C "eeprom" driver ... except this driver
supports write access, and multiple EEPROM sizes.
From: "Tuppa, Walter" <walter.tuppa@siemens.com>
Since I have EEPROMs on SPI with different address sizing, I made some
changes to your at25.c to support them. Works perfectly. (Also includes a
small bugfix for the "what size address" test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Walter Tuppa <walter.tuppa@siemens.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This clarifies some aspects of the SPI programming interface, based on
feedback from Hans-Peter Nilsson. The in-memory representation of words is
right-aligned, so for example a twelve bit word is stored using sixteen bits
with four undefined bits in the MSB. And controller drivers must reject
protocol tweaking modes they do not support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'd like to assign NULL to kfree()d members of a structure. I can't do
that without ugly casting (see the PXA patch) when the structure pointed to
is const-qualified. I don't really see a reason why the cleanup method
isn't allowed to alter the object it should clean up. :-)
No, I didn't test the PXA patch, but I verified that the NULL-assignment
doesn't stop me from doing rmmod/insmodding my own spi_bitbang-based
driver.
Signed-off-by: Hans-Peter Nilsson <hp@axis.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the spi_unregister_driver() code fit in with the rest of the header
file, and only do the action if the driver passed is non-NULL.
This also makes the code a line smaller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add wrappers for getting and setting the driver data using spi_device
instead of using dev_{get|set}_drvdata with &spi->dev, to mirror the
platform_{get|set}_drvdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
This reverts commit 2943ecf2ed32632473c06f1975db47a7aa98c10f.
This should go through the SPI maintainer, it was my fault that it did
not. Especially as it conflicts with other patches he has pending.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Cc: <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On some LCDs leaving the Vref on provides much better readings.
Signed-off-by: Jarkko Oikarinen <jarkko.oikarinen@nokia.com>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Some LCDs like the LS041Y3 require a customized filtering
logic for reliable readings, so make the filtering function
replacable through platform specific hooks.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Some issues were recently turned up with the current specification of what
it means for spi_transfer.tx_buf to be null, as part of transfers which are
(from the SPI protocol driver perspective) pure reads.
Specifically, that it seems better to change the TX behaviour there from
"undefined" to "will shift zeroes". This lets protocol drivers (like the
ads7846 driver) depend on that behavior. It's what most controller drivers
in the tree are already doing (with one exception and one case of driver
wanting-to-oops), it's what Microwire hardware will necessarily be doing,
and it removes an issue whereby certain security audits would need to
define such a value anyway as part of removing covert channels.
This patch changes the specification to require shifting zeroes, and
updates all currently merged SPI controller drivers to do so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices. Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
and export it
Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This removes superfluous whitespace in the <linux/spi/spi.h> header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer. They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.
The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.
Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.
When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Some touchscreens seem to oscillate heavily for a while after touching
the screen. Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
gcc4 generates warnings when a non-FASTCALL function pointer is assigned to a
FASTCALL one. Perhaps it has taste.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This was originally a driver for the ST M25P80 SPI flash. It's been
updated slightly to handle other M25P series chips.
For many of these chips, the specific type could be probed, but for now
this just requires static setup with flash_platform_data that lists the
chip type (size, format) and any default partitioning to use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mike Lavender <mike@steroidmicros.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds a bitbanging spi master, hooking up to board/adapter-specific glue
code which knows how to set and read the signals (gpios etc).
This code kicks in after the glue code creates a platform_device with the
right platform_data. That data includes I/O loops, which will usually
come from expanding an inline function (provided in the header). One goal
is that the I/O loops should be easily optimized down to a few GPIO register
accesses, in common cases, for speed and minimized overhead.
This understands all the currently defined protocol tweaking options in the
SPI framework, and might eventually serve as as reference implementation.
- different word sizes (1..32 bits)
- differing clock rates
- SPI modes differing by CPOL (affecting chip select and I/O loops)
- SPI modes differing by CPHA (affecting I/O loops)
- delays (usecs) after transfers
- temporarily deselecting chips in mid-transfer
A lot of hardware could work with this framework, though common types of
controller can't reach peak performance without switching to a driver
structure that supports pipelining of transfers (e.g. DMA queues) and maybe
controllers (e.g. IRQ driven).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This updates the ads7864 driver to use the new "spi_driver" struct, and
includes some minor unrelated cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This includes various updates to the SPI core:
- Fixes a driver model refcount bug in spi_unregister_master() paths.
- The spi_master structures now have wrappers which help keep drivers
from needing class-level get/put for device data or for refcounts.
- Check for a few setup errors that would cause oopsing later.
- Docs say more about memory management. Highlights the use of DMA-safe
i/o buffers, and zero-initializing spi_message and such metadata.
- Provide a simple alloc/free for spi_message and its spi_transfer;
this is only one of the possible memory management policies.
Nothing to break code that already works.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a refresh of the "Simple SPI Framework" found in 2.6.15-rc3-mm1
which makes the following changes:
* There's now a "struct spi_driver". This increase the footprint
of the core a bit, since it now includes code to do what the driver
core was previously handling directly. Documentation and comments
were updated to match.
* spi_alloc_master() now does class_device_initialize(), so it can
at least be refcounted before spi_register_master(). To match,
spi_register_master() switched over to class_device_add().
* States explicitly that after transfer errors, spi_devices will be
deselected. We want fault recovery procedures to work the same
for all controller drivers.
* Minor tweaks: controller_data no longer points to readonly data;
prevent some potential cast-from-null bugs with container_of calls;
clarifies some existing kerneldoc,
And a few small cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a conversion of the AT91rm9200 DataFlash MTD driver to use the
lightweight SPI framework, and no longer be AT91-specific. It compiles
down to less than 3KBytes on ARM.
The driver allows board-specific init code to provide platform_data with
the relevant MTD partitioning information, and hotplugs.
This version has been lightly tested. Its parent at91_dataflash driver has
been pretty well banged on, although kernel.org JFFS2 dataflash support was
acting broken the last time I tried it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers. Key differences from those two:
- Uses the new SPI framework (minimalist version)
- <linux/spi/ads7846.h> abstracts board-specific touchscreen info
- Sysfs attributes for the temperature and voltage sensors
- Uses fewer ARM-specific IRQ primitives
The temperature and voltage sensors show up in sysfs like this:
$ pwd
/sys/devices/platform/omap-uwire/spi2.0
$ ls
bus@ input:event0@ power/ temp1 vbatt
driver@ modalias temp0 vaux
$ cat modalias
ads7846
$ cat temp0
991
$ cat temp1
1177
$
So far only basic testing has been done. There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.
One portability note may be of special interest. It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response". Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention. So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).
- It's still less than 2KB of ".text" (ARM). If there's got to be a
mid-layer for something so simple, that's the right size budget. :)
- The guts use board-specific SPI device tables to build the driver
model tree. (Hardware probing is rarely an option.)
- This version of Kconfig includes no drivers. At this writing there
are two known master controller drivers (PXA/SSP, OMAP MicroWire)
and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
mentions of other drivers in development.
- No userspace API. There are several implementations to compare.
Implement them like any other driver, and bind them with sysfs.
The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:
- One bugfix (removes a FIXME), with the visible effect of making device
names be "spiB.C" where B is the bus number and C is the chipselect.
- The "caller provides DMA mappings" mechanism now has kerneldoc, for
DMA drivers that want to be fancy.
- Hey, the framework init can be subsys_init. Even though board init
logic fires earlier, at arch_init ... since the framework init is
for driver support, and the board init support uses static init.
- Various additional spec/doc clarifications based on discussions
with other folk. It adds a brief "thank you" at the end, for folk
who've helped nudge this framework into existence.
As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.
From: Mark Underwood <basicmark@yahoo.com>
Update the SPI framework to remove a potential priority inversion case by
reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
