| Age | Commit message (Collapse) | Author |
|---|
|
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
in the target tree above)
This is a summery of the wire changes:
* OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
* Attributes List Element Header grew, so attribute values are 8 bytes
aligned.
* Cryptographic keys and signatures are 20 => 32
* Few new definitions.
(Still missing new standard definitions attribute values, these do not change
wire format and will be added later when needed)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.
In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
FIP is the new standard way to discover Fibre-Channel Forwarders (FCFs)
by sending solicitations and listening for advertisements from FCFs.
It also provides for keep-alives and period advertisements so that both
parties know they have connectivity. If the FCF loses connectivity to
the storage fabric, it can send a Link Reset to inform the E_node.
This version is also compatible with pre-FIP implementations, so no
configured selection between FIP mode and non-FIP mode is required.
We wait a couple seconds after sending the initial solicitation
and then send an old-style FLOGI. If we receive any FIP frames,
we use FIP only mode. If the old FLOGI receives a response,
we disable FIP mode. After every reset or link up, this
determination is repeated.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Adds include/scsi/fc/fc_fip.h for FIP protocol definitions.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The foce_softc mem was reserved by libfc_host_alloc as well as
by fcoe_host_alloc.
Removes one liner fcoe_host_alloc completely, instead directly calls
libfc_host_alloc to alloc scsi_host with libfc for just one fcoe_softc
as fcoe private data.
Moves libfc_host_alloc to libfc.h since it is a libfc API, placed
lport_priv API adjacent to libfc_host_alloc since this is related
to scsi_host priv data.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Removes no where used several inline functions prefixed with skb_*
and be16_to_cpu.
Moves fcoe module specific func prototypes to fcoe.c from libfcoe.h,
moved only need for build.
Adds fcoe module header file fcoe.h and then moves fcoe module
specific fcoe_percpu_s and fcoe_softc to fcoe.h from libfcoe.h.
Moves all defines from fcoe.c to fcoe.h since now fcoe module
has its own header file fcoe.h.
[jejb: removed EXPORT_SYMBOL_GPL(fcoe_fc_crc) which caused a section mismatch]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Moves only required code from fcoe_sw.c to libfcoe.c towards having
just one source file for fcoe module, this gets rid off default sw
transport code in a separate fcoe_sw.c file.
Very minor renaming along this move, dropped _sw_ or _SW_ use
in names and replaced them by _if_ as a auxiliary interface
functions. Now some of these funcs can be removed or merged with
other func after fcoe transport is gone, but that should be
in another patch to keep this patch simple.
Now the libfcoe.c file name for fcoe module doesn't go along well,
so the libfcoe.c file renaming to fcoe.c as the only single fcoe
module file is done in next patch to keep this patch clean
and small for review.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Remove unused fc_transport_fcoe.c and fc_transport_fcoe.h
files.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The fcoe transport code was added for generic FCoE transport
infrastructure to allow additional offload related module loading
on demand, this is not required anymore after recently added
different offload approach by having offload related func ops
in netdev.
This patch removes fcoe transport related code use, calls functions
directly between existing libfcoe.c and fcoe_sw.c for now, for
example fcoe_sw_destroy and fcoe_sw_create calling.
The fcoe_sw.c and libfcoe.c code will be further consolidated in
later patches and then also the default fcoe sw transport code
file fcoe_sw.c will be completely removed.
The fcoe transport code files are completely removed in next
patch to keep this patch simple for reviewing.
[This patch is an update to a previous patch. This update
resolves a build error as well as fixes a defect related to
not calling fc_release_transport().]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Remove the hotplug creation of dev_stats, we allocate for all possible CPUs
now when we allocate the lport.
v2: Durring the 2.6.30 merge window, before these patches were comitted,
'percpu_ptr' was renamed 'per_cpu_ptr'. This latest update updates this
patch for the name change.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Convert fcoe_percpu array to use the per-cpu variables
that the kernel provides. Use the kernel's functions to
access this structure.
The cpu member of the fcoe_percpu_s is no longer needed,
so this patch removes it too.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Currently the skb_queue is initialized every time the associated
CPU goes online. This patch has libfcoe initializing the skb_queue
for all possible CPUs when the module is loaded.
This patch also re-orders some declarations in the fcoe_rcv()
function so the structure declarations are grouped before
the primitive declarations.
Lastly, this patch converts all CPU indicies to use unsigned int
since CPU indicies should not be negative.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The api for conn and session failures is akward because
one takes a conn from the lib and one takes a session
from the class. This syncs up the interfaces to use
structs from the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We never should hit the lock up that is spit out when
lock dep is on and we logout. But we have been using the
shost work queue in a odd way. This patch has us use the
work queue for scanning instead of creating our own,
and this ends up also killing the lock dep warnings.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This makes the logging a compile time option and replaces
the scsi_debug macro with session and connection ones
that print out a driver model id prefix.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When LLD supports direct data placement (ddp) for large receive of an scsi
i/o coming into fc_fcp, we call into libfc_function_template's ddp_setup()
to prepare for a ddp of large receive for this read I/O. When I/O is complete,
we call the corresponding ddp_done() to get the length of data ddped as well
as to let LLD do clean up.
fc_fcp_ddp_setup()/fc_fcp_ddp_done() are added to setup and complete a ddped
read I/O described by the given fc_fcp_pkt. They would call into corresponding
ddp_setup/ddp_done implemented by the fcoe layer. Eventually, fcoe layer calls
into LLD's ddp_setup/ddp_done provided through net_device
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This checks if net_devices supports FCoE offload ops in netdev_ops and it
if it does, then sets up the corresponding flags in the associated fc_lport.
For large send offload, the maximum length supported in one large send is now
described by the added lso_max in fc_lport, which is setup initially from
netdev->gso_max_size.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This adds eth type ETH_P_FCOE for Fibre Channel over Ethernet (FCoE),
consequently, the ETH_P_FCOE from fc_fcoe.h and fcoe skb->protocol
is not set as ETH_P_FCOE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This allows it to compile and be used on the ps3 platform that wants
to use the #define values in scsi.h without actually having
CONFIG_SCSI set.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
No one uses scsi_execute_async with data transfer now. We can remove
scsi_req_map_sg.
Only scsi_eh_lock_door uses scsi_execute_async. scsi_eh_lock_door
doesn't handle sense and the callback. So we can remove
scsi_io_context too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Implementation of the osd_req_decode_sense() API. Can be called by
library users to decode what failed in command executions.
Add SCSI_OSD_DPRINT_SENSE Kconfig variable. Possible values are:
0 - Do not print any errors to messages file <KERN_ERR>
1 - (Default) Print only decoded errors that are not recoverable.
Recoverable errors are those that the target has complied with
the request but with a warning. For example read passed end of
object will return zeros after the last valid byte.
2- Print all errors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Auto detect an OSDv2 or OSDv1 target at run time. Note how none
of the OSD API calls change. The tests do not know what device
version it is.
This test now passes against both the IBM-OSD-SIM OSD1 target
as well as OSC's OSD2 target.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for OSD2 at run time. It is now possible to run with
both OSDv1 and OSDv2 targets at the same time. The actual detection
should be preformed by the security manager, as the version is encoded
in the capability structure.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Support for both List-Mode and Page-Mode osd attributes. One of
these operations may be added to most other operations.
Define the OSD standard's attribute pages constants and structures
(osd_attributes.h)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Kernel clients like exofs can retrieve struct osd_dev(s)
by means of below API.
+ osduld_path_lookup() - given a path (e.g "/dev/osd0") locks and
returns the corresponding struct osd_dev, which is then needed
for subsequent libosd use.
+ osduld_put_device() - free up use of an osd_dev.
Devices can be shared by multiple clients. The osd_uld_device's
life time is governed by an embedded kref structure.
The osd_uld_device holds an extra reference to both it's
char-device and it's scsi_device, and will release these just
before the final deallocation.
There are three possible lock sources of the osd_uld_device
1. First and for most is the probe() function called by
scsi-ml upon a successful login into a target. Released in release()
when logout.
2. Second by user-mode file handles opened on the char-dev.
3. Third is here by Kernel users.
All three locks must be removed before the osd_uld_device is freed.
The MODULE has three lock sources as well:
1. scsi-ml at probe() time, removed after release(). (login/logout)
2. The user-mode file handles open/close.
3. Import symbols by client modules like exofs.
TODO:
This API is not enough for the pNFS-objects LD. A more versatile
API will be needed. Proposed API could be:
struct osd_dev *osduld_sysid_lookup(const char id[OSD_SYSTEMID_LEN]);
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add a Linux driver module that registers as a SCSI ULD and probes
for OSD type SCSI devices.
When an OSD-type SCSI device is found a character device is created
in the form of /dev/osdX - where X goes from 0 up to hard coded 64.
The Major character device number used is 260.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Headers only patch.
osd_protocol.h
Contains a C-fied definition of the T10 OSD standard
osd_types.h
Contains CPU order common used types
osd_initiator.h
API definition of the osd_initiator library
osd_sec.h
Contains High level API for the security manager.
[Note that checkpatch spews errors on things that are valid in this context
and will not be fixed]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
- Define the OSD_TYPE scsi device and let it show up in scans
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_device_online() is not just a negation of SDEV_OFFLINE,
also devices in state SDEV_DEL are actually offline.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Based on prior work by Martin Petersen and James Bottomley, this patch
adds a generic helper for retrieving VPD pages from SCSI devices.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
status
frames followed by these errors in log.
[sdp] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[sdp] Sense Key : Aborted Command [current]
[sdp] Add. Sense: Data phase error
This was causing some test apps to exit due to write failure under heavy
load.
This was due to a race around adding and removing tx frame skb in
fcoe_pending_queue, Chris Leech helped me to find that brief unlocking
period when pulling skb from fcoe_pending_queue in various contexts
(fcoe_watchdog and fcoe_xmit) and then adding skb back into fcoe_pending_queue
up on a failed fcoe_start_io could change skb/tx frame order in
fcoe_pending_queue. Thanks Chris.
This patch allows only single context to pull skb from fcoe_pending_queue
at any time to prevent above described ordering issue/race by use of
fcoe_pending_queue_active flag.
This patch simplified fcoe_watchdog with modified fcoe_check_wait_queue by
use of FCOE_LOW_QUEUE_DEPTH instead previously used several conditionals
to clear and set lp->qfull.
I think FCOE_MAX_QUEUE_DEPTH with FCOE_LOW_QUEUE_DEPTH will work better
in re/setting lp->qfull and these could be fine tuned for performance.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Comment from "Andrew Morton <akpm@linux-foundation.org>"
> +{
> + return (struct fcoe_softc *)lport_priv(lp);
unneeded/undesirable cast of void*. There are probably zillions of
instances of this - there always are.
This whole inline function was unnecessary. The FCoE layer knows
that it's data structure is stored in the lport private data, it
can just access it from lport_priv().
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
1) Added '()' for function names in kerneldoc comments
2) Changed comment bookends from '**/' to '*/'. The comment on the the
mailing list was that '**/' "is consistently unconventional. Not
wrong, just odd." The Documentation/kernel-doc-nano-HOWTO.txt
states that kerneldoc comment blocks should end with '**/' but most
(if not all) instance I found under drivers/scsi/ were only using
the '*/' so I converted to that style.
3) Removed incorrect linebreaks in kerneldoc comments where found
4) Removed a few unnecessary blank comment lines in kerneldoc comment
blocks
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Made the comments more like the comments for struct scsi_host_template.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This allows any rport ELS to retry on LS_RJT.
The rport error handling would only retry on resource allocation failures
and exchange timeouts. I have a target that will occasionally reject PLOGI
when we do a quick LOGO/PLOGI. When a critical ELS was rejected, libfc would
fail silently leaving the rport in a dead state.
The retry count and delay are managed by fc_rport_error_retry. If the retry
count is exceeded fc_rport_error will be called. When retrying is not the
correct course of action, fc_rport_error can be called directly.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
lport->link_status
The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-
1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.
2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.
The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.
Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.
This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.
Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
fc_exch_mgr structure is private to fc_exch.c. To export exch_mgr_reset to
transport, transport needs access to the exch manager. Change
exch_mgr_reset to use lport param which is the shared structure between
libFC and transport.
Alternatively, fc_exch_mgr definition can be moved to libfc.h so that lport
can be accessed from mp*.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
virt_to_page() call should not be used on kernel text and data
addresses. virt_to_page() is used by sg_init_one(). So change padbuf
to be allocated within iscsi_segment.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
