| Age | Commit message (Collapse) | Author |
|---|
|
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/vxy/lksctp-dev
|
|
Cell phone networks do link layer retransmissions and other
things that cause unnecessary timeout retransmits. So allow
the minimum RTO to be inflated per-route to deal with this.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4561/1: i.MX/MX1 GPIO parenthes omission and input setup fix
[ARM] 4557/1: Fix PXA irq gpio initialization
[ARM] 4551/1: s3c24xx: fix wrong virtual address offsets
[ARM] 4552/1: i.MX/MX1 GPIO output setup fix
[ARM] 4553/1: ARM at91: define FIQ_START
[ARM] 4554/1: replace consistent_sync() with flush_ioremap_region()
ARM: OMAP: Enable serial idling and wakeup features
ARM: OMAP2: Force APLLs always active
ARM: OMAP: H3 workqueue fixes
ARM: OMAP: OSK led fixes
ARM: OMAP: fix OMAP1 dmtimer build warning
ARM: OMAP: Fix 32k timer unsupported one-shot mode
|
|
PROTOCOL VIOLATION error cause in ABORT is bad encode when make abort
chunk. When SCTP encode ABORT chunk with PROTOCOL VIOLATION error cause,
it just add the error messages to PROTOCOL VIOLATION error cause, the
rest four bytes(struct sctp_paramhdr) is just add to the chunk, not
change the length of error cause. This cause the ABORT chunk to be a bad
format. The chunk is like this:
ABORT chunk
Chunk type: ABORT (6)
Chunk flags: 0x00
Chunk length: 72 (*1)
Protocol violation cause
Cause code: Protocol violation (0x000d)
Cause length: 62 (*2)
Cause information: 5468652063756D756C61746976652074736E2061636B2062...
Cause padding: 0000
[Needless] 00030010
Chunk Length(*1) = 72 but Cause length(*2) only 62, not include the
extend 4 bytes.
((72 - sizeof(chunk_hdr)) = 68) != (62 +3) / 4 * 4
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
When we recieve a FWD-TSN (meaning the peer has abandoned the data),
we need to clean up any partially received messages that may be
hanging out on the re-assembly or re-ordering queues. This is
a MUST requirement that was not properly done before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com.>
|
|
de-HZ-ification of the granularity defaults unearthed a pre-existing
property of CFS: while it correctly converges to the granularity goal,
it does not prevent run-time fluctuations in the range of
[-gran ... 0 ... +gran].
With the increase of the granularity due to the removal of HZ
dependencies, this becomes visible in chew-max output (with 5 tasks
running):
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
out: 27 . 27. 32 | flu: 0 . 0 | ran: 17 . 13 | per: 44 . 40
out: 27 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 36 . 40
out: 29 . 27. 32 | flu: 2 . 0 | ran: 17 . 13 | per: 46 . 40
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
out: 29 . 27. 32 | flu: 0 . 0 | ran: 18 . 13 | per: 47 . 40
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
average slice is the ideal 13 msecs and the period is picture-perfect 40
msecs. But the 'ran' field fluctuates around 13.33 msecs and there's no
mechanism in CFS to keep that from happening: it's a perfectly valid
solution that CFS finds.
to fix this we add a granularity/preemption rule that knows about
the "target latency", which makes tasks that run longer than the ideal
latency run a bit less. The simplest approach is to simply decrease the
preemption granularity when a task overruns its ideal latency. For this
we have to track how much the task executed since its last preemption.
( this adds a new field to task_struct, but we can eliminate that
overhead in 2.6.24 by putting all the scheduler timestamps into an
anonymous union. )
with this change in place, chew-max output is fluctuation-less all
around:
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 1 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 1 | ran: 13 . 13 | per: 41 . 40
this patch has no impact on any fastpath or on any globally observable
scheduling property. (unless you have sharp enough eyes to see
millisecond-level ruckles in glxgears smoothness :-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mike Galbraith <efault@gmx.de>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Make flush_tlb_kernel_range() an inline function.
[SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
[SPARC32]: Kill unused vars and macros from prom/console.c
[SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
[VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
[SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Mark Paul Moore as maintainer of labelled networking.
[VLAN/BRIDGE]: Fix "skb_pull_rcsum - Fatal exception in interrupt"
[ISDN]: Get rid of some pointless allocation casts in common and bsd comp.
[NET]: Avoid pointless allocation casts in BSD compression module
[IRDA]: Do not do pointless kmalloc return value cast in KingSun driver
[NET]: Fix crash in dev_mc_sync()/dev_mc_unsync()
[PPPOL2TP]: Fix endianness annotations.
[IOAT]: ioatdma needs to to play nice in a multi-dma-client world
[SLIP]: trivial sparse warning fix
[EQL]: sparse warning fix
[NET]: is_power_of_2 in net/core/neighbour.c
[TCP]: Describe tcp_init_cwnd() thoroughly in a comment.
[NET]: Fix IP_ADD/DROP_MEMBERSHIP to handle only connectionless
[KBUILD]: Sanitize tc_ematch headers.
[IPSEC] AH4: Update IPv4 options handling to conform to RFC 4302.
|
|
Adding the defines/constants activates the existing code in the tty layer
and allows arbitary tty speeds to be requested on this platform
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Add support for processors that have cache-aliasing issues, such as
the Stretch S5000 processor. Cache-aliasing means that the size of
the cache (for one way) is larger than the page size, thus, a page
can end up in several places in cache depending on the virtual to
physical translation. The method used here is to map a user page
temporarily through the auto-refill way 0 and of of the DTLB.
We probably will want to revisit this issue and use a better
approach with kmap/kunmap.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Add kernel module support.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Newer processor versions starting with Xtensa6/LX2 support an 'executable'
bit for memory pages. This bit replaces the 'valid' bit, so it must be
always set to one for older processor versions. To mark a page invalid, we now
set the cache-attributes to b11, which is backward compatible.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Use the generic version of get_order for processor configurations that
don't have the 'nsa/nsau' instructions.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Add macros (__XTENSA_UL and __XTENSA_UL_CONST) for typecasting
constants.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
The timer code could have missed a tick.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Xtensa passes long long arguments in a even/odd register pair,
so we also need to shuffle the arguments when passed through the
system call to avoid an empty argument register.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
We don't need to include processor.h in bug.h.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Although __ARCH_WANT_SYS_GETPGRP was defined, the actualy entry for
the getpgrp system-call was missing.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Add missing system calls that have been recently added to the kernel
for the Xtensa architecture and define __IGNORE macros for system calls
that we don't need for Xtensa.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (60 commits)
[MIPS] Fulong doesn't need ISA DMA.
[MIPS] IP27: intr_sconnect_level: don't disable interrupts.
[MIPS] IP27: startup_bridge_irq: connect interrupt.
[MIPS] IP27: shutdown_bridge_irq: don't free irq.
[MIPS] Sort out handling of ISA-less PCI systems.
[MIPS] Add __cmpdi2
[MIPS] HOTPLUG: Make register_pci_controller __devinit.
[MIPS] PCI: Remove __devinit attribute from pcibios_fixup_bus.
[MIPS] PCI: Remove __devinit attribute from pcibios_fixup_bus.
[MIPS] Delete duplicate inclusion of <linux/delay.h>.
[MIPS] Polish <asm/edac.h>.
[MIPS] IP22: Export sgi_gfxaddr for use by the Newport console driver.
[MIPS] Maintain si_code field properly for FP exceptions
[MIPS] SMTC: Fix duplicate status dumps on NMI
[MIPS] Unconditionally writeback and invalidate caches on kexec.
[PATCH] rtc: Make rtc-rs5c348 driver hotplug-aware
[MIPS] Fix gcc 3.3 warning.
[MIPS] Fix invalid semicolon after if statement
[MIPS] Update Cobalt defconfig
[MIPS] Update workpad_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix SLB initialization at boot time
[POWERPC] Fix undefined reference to device_power_up/resume
[POWERPC] cell: Update cell_defconfig for 2.6.23
[POWERPC] axonram: Do not delete gendisks queue in error path
[POWERPC] axonram: Module modification for latest firmware API changes
[POWERPC] cell: Support pinhole-reset on IBM cell blades
[POWERPC] spu_manage: Use newer physical-id attribute
[POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] Add NOTES section
[PARISC] Use compat_sys_getdents
[PARISC] Do not allow STI_CONSOLE to be modular
[PARISC] Clean up sti_flush
[PARISC] Add dummy isa_(bus|virt)_to_(virt|bus) inlines
[PARISC] Add empty <asm-parisc/vga.h>
|
|
Less painful than fixing up the Kconfig for a pile of drivers to only build
on X86 && ARM && MIPS...
Just make them BUG(), as defining them to be 1:1 with physical memory will
likely HPMC the box anyways.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
|
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
|
This avoids unused variable warnings in places like mm/vmalloc.c:
mm/vmalloc.c: In function ‘unmap_kernel_range’:
mm/vmalloc.c:75: warning: unused variable ‘start’
caused by it previously being a macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
{s,d}_{session,tunnel} in pppol2tp_addr are actually host-endian
everywhere. We might switch them to net-endian, of course, but
that structure is exposed to userland via getname...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The headers in tc_ematch are used by iproute2, so these headers should
be processed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Work around gcc 3.3's unability to evaluate that certain expressions indeed
are constant.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
And gcc 3.4 doesn't even warn out this, grrr.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CC arch/mips/kernel/traps.o
arch/mips/kernel/traps.c: In function 'show_backtrace':
arch/mips/kernel/traps.c:110: warning: unused variable 'ra'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Cleanup jmr3927, tx4927 and tx4938 irq codes, using common IRQ_CPU,
I8259 and IRQ_TXX9 irq routines.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
For the generation of asm-offset.h to work these need to be evaulatable
by gcc as a constant expression. This issue did exist for a while but
didn't bite because they're only in asm-offset.h for debugging purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: cleanup, sched_granularity -> sched_min_granularity
sched: adaptive scheduler granularity
sched: fix CONFIG_SCHED_DEBUG dependency of lockdep sysctls
|
|
due to adaptive granularity scheduling the role of sched_granularity
has changed to "minimum granularity", so rename the variable (and the
tunable) accordingly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
|
|
Instead of specifying the preemption granularity, specify the wanted
latency. By fixing the granlarity to a constany the wakeup latency
it a function of the number of running tasks on the rq.
Invert this relation.
sysctl_sched_granularity becomes a minimum for the dynamic granularity
computed from the new sysctl_sched_latency.
Then use this latency to do more intelligent granularity decisions: if
there are fewer tasks running then we can schedule coarser. This helps
performance while still always keeping the latency target.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: balance ioremap checks
agp: Add device id for P4M900 to via-agp module
efficeon-agp leaks 'struct agp_bridge_data' in error paths of agp_efficeon_probe()
|
|
master.kernel.org:/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
|
|
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Current Linus tree fails to link on pmac32:
drivers/built-in.o: In function `pmac_wakeup_devices':
via-pmu.c:(.text+0x5bab4): undefined reference to `device_power_up'
via-pmu.c:(.text+0x5bb08): undefined reference to `device_resume'
drivers/built-in.o: In function `pmac_suspend_devices':
via-pmu.c:(.text+0x5c260): undefined reference to `device_power_down'
via-pmu.c:(.text+0x5c27c): undefined reference to `device_resume'
make[1]: *** [.tmp_vmlinux1] Error 1
changing CONFIG_PM > CONFIG_PM_SLEEP leads to:
drivers/built-in.o: In function `pmu_led_set':
via-pmu-led.c:(.text+0x5cdca): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5cdce): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `pmu_req_done':
via-pmu-led.c:(.text+0x5ce3e): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5ce42): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `adb_init':
(.init.text+0x4c5c): undefined reference to `pmu_register_sleep_notifier'
make[1]: *** [.tmp_vmlinux1] Error 1
So change even more places from PM to PM_SLEEP to allow linking.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Conflicts:
drivers/acpi/video.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
