| Age | Commit message (Collapse) | Author |
|---|
|
of other archs
PTRACE_SYSEMU{,_SINGLESTEP} is actually arch specific, for now, and the
current allocated number clashes with a ptrace code of frv, i.e.
PTRACE_GETFDPIC. I should have submitted this much earlier, anyway we get no
breakage for this.
CC: Daniel Jacobowitz <dan@debian.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Reduce the size of the pageframe for NR_CPUS>4, CONFIG_PREEMPT back to the
minimal size by unionising both ->private and ->mapping with the pagetable
lock.
It uses an anonymous struct and hence requires gcc-3.x.
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Reorder members of the kiocb structure to make sync kiocb setup faster. By
setting the elements sequentially, the write combining buffers on the CPU
are able to combine the writes into a single burst, which results in fewer
cache cycles being consumed, freeing them up for other code. This results
in a 10-20KB/s[*] increase on the bw_unix part of LMbench on my test
system.
* The improvement varies based on what other patches are in the system,
as there are a number of bottlenecks, so this number is not absolutely
accurate.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a hook so architectures can validate /dev/mem mmap requests.
This is analogous to validation we already perform in the read/write
paths.
The identity mapping scheme used on ia64 requires that each 16MB or
64MB granule be accessed with exactly one attribute (write-back or
uncacheable). This avoids "attribute aliasing", which can cause a
machine check.
Sample problem scenario:
- Machine supports VGA, so it has uncacheable (UC) MMIO at 640K-768K
- efi_memmap_init() discards any write-back (WB) memory in the first granule
- Application (e.g., "hwinfo") mmaps /dev/mem, offset 0
- hwinfo receives UC mapping (the default, since memmap says "no WB here")
- Machine check abort (on chipsets that don't support UC access to WB
memory, e.g., sx1000)
In the scenario above, the only choices are
- Use WB for hwinfo mmap. Can't do this because it causes attribute
aliasing with the UC mapping for the VGA MMIO space.
- Use UC for hwinfo mmap. Can't do this because the chipset may not
support UC for that region.
- Disallow the hwinfo mmap with -EINVAL. That's what this patch does.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There's one scsi driver which doesn't compile due to weird __VA_ARGS__ tricks
and the rather useful scsi/sd.c is currently getting an ICE. None of the new
SAS code compiles, due to extensive use of anonymous unions. The V4L guys are
very good at exploiting the gcc-2.95.x macro expansion bug (_why_ does each
driver need to implement its own debug macros?) and various people keep on
sneaking in anonymous unions, which are rather nice.
Plus anonymous unions are rather useful.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I found that blkp field was not used in kernel tree.
As most of the times NR_CPUS is a power of two and kmalloc() memory blocks
too, this extra field basically doubles the memory space allocated in
__alloc_percpu() to store the 'struct percpu_data'
(for example, if NR_CPUS=8 on i386, kmalloc(4*8+4) returns a 64 bytes block
instead of a 32 bytes block after this patch)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch inlines the single user of struct super_block field
s_old_blocksize and removes the field.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some long time ago, dentry struct was carefully tuned so that on 32 bits
UP, sizeof(struct dentry) was exactly 128, ie a power of 2, and a multiple
of memory cache lines.
Then RCU was added and dentry struct enlarged by two pointers, with nice
results for SMP, but not so good on UP, because breaking the above tuning
(128 + 8 = 136 bytes)
This patch reverts this unwanted side effect, by using an union (d_u),
where d_rcu and d_child are placed so that these two fields can share their
memory needs.
At the time d_free() is called (and d_rcu is really used), d_child is known
to be empty and not touched by the dentry freeing.
Lockless lookups only access d_name, d_parent, d_lock, d_op, d_flags (so
the previous content of d_child is not needed if said dentry was unhashed
but still accessed by a CPU because of RCU constraints)
As dentry cache easily contains millions of entries, a size reduction is
worth the extra complexity of the ugly C union.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Paul Jackson <pj@sgi.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@epoch.ncsc.mil>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Small cleanups in shared mounts code.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While rooting aroung in the signal code trying to understand how to fix the
SIG_IGN ploy (set sig handler to SIG_IGN and flood system with high speed
repeating timers) I came across what, I think, is a problem in sigaction()
in that when processing a SIG_IGN request it flushes signals from 1 to
SIGRTMIN and leaves the rest. Attempt to fix this.
Signed-off-by: George Anzinger <george@mvista.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make it possible for a running process (such as gssapid) to be able to
instantiate a key, as was requested by Trond Myklebust for NFS4.
The patch makes the following changes:
(1) A new, optional key type method has been added. This permits a key type
to intercept requests at the point /sbin/request-key is about to be
spawned and do something else with them - passing them over the
rpc_pipefs files or netlink sockets for instance.
The uninstantiated key, the authorisation key and the intended operation
name are passed to the method.
(2) The callout_info is no longer passed as an argument to /sbin/request-key
to prevent unauthorised viewing of this data using ps or by looking in
/proc/pid/cmdline.
This means that the old /sbin/request-key program will not work with the
patched kernel as it will expect to see an extra argument that is no
longer there.
A revised keyutils package will be made available tomorrow.
(3) The callout_info is now attached to the authorisation key. Reading this
key will retrieve the information.
(4) A new field has been added to the task_struct. This holds the
authorisation key currently active for a thread. Searches now look here
for the caller's set of keys rather than looking for an auth key in the
lowest level of the session keyring.
This permits a thread to be servicing multiple requests at once and to
switch between them. Note that this is per-thread, not per-process, and
so is usable in multithreaded programs.
The setting of this field is inherited across fork and exec.
(5) A new keyctl function (KEYCTL_ASSUME_AUTHORITY) has been added that
permits a thread to assume the authority to deal with an uninstantiated
key. Assumption is only permitted if the authorisation key associated
with the uninstantiated key is somewhere in the thread's keyrings.
This function can also clear the assumption.
(6) A new magic key specifier has been added to refer to the currently
assumed authorisation key (KEY_SPEC_REQKEY_AUTH_KEY).
(7) Instantiation will only proceed if the appropriate authorisation key is
assumed first. The assumed authorisation key is discarded if
instantiation is successful.
(8) key_validate() is moved from the file of request_key functions to the
file of permissions functions.
(9) The documentation is updated.
From: <Valdis.Kletnieks@vt.edu>
Build fix.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a new keyctl function that allows the expiry time to be set on a key or
removed from a key, provided the caller has attribute modification access.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
SUS requires that when truncating a file to the size that it currently
is:
truncate and ftruncate should NOT modify ctime or mtime
O_TRUNC SHOULD modify ctime and mtime.
Currently mtime and ctime are always modified on most local
filesystems (side effect of ->truncate) or never modified (on NFS).
With this patch:
ATTR_CTIME|ATTR_MTIME are sent with ATTR_SIZE precisely when
an update of these times is required whether size changes or not
(via a new argument to do_truncate). This allows NFS to do
the right thing for O_TRUNC.
inode_setattr nolonger forces ATTR_MTIME|ATTR_CTIME when the ATTR_SIZE
sets the size to it's current value. This allows local filesystems
to do the right thing for f?truncate.
Also, the logic in inode_setattr is changed a bit so there are two return
points. One returns the error from vmtruncate if it failed, the other
returns 0 (there can be no other failure).
Finally, if vmtruncate succeeds, and ATTR_SIZE is the only change
requested, we now fall-through and mark_inode_dirty. If a filesystem did
not have a ->truncate function, then vmtruncate will have changed i_size,
without marking the inode as 'dirty', and I think this is wrong.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make it possible to include linux/pagevec.h multiple times without
incurring errors due to duplicate definitions.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch renames relayfs_file_operations to relay_file_operations, and the
file operations themselves from relayfs_XXX to relay_file_XXX, to make it more
clear that they refer to relay files.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds the optional is_global outparam to the create_buf_file()
callback. This can be used by clients to create a single global relayfs
buffer instead of the default per-cpu buffers. This was suggested as being
useful for certain debugging applications where it's more convenient to be
able to get all the data from a single channel without having to go to the
bother of dealing with per-cpu files.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds a couple of callback functions that allow a client to hook
into relay_open()/close() and supply the files that will be used to represent
the channel buffers; the default implementation if no callbacks are defined is
to create the files in relayfs. This is to support the creation and use of
relay files in other filesystems such as debugfs, as implied by the fact that
relayfs_file_operations are exported.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Since we're no longer using relayfs_inode_info, remove relayfs_alloc_inode()
and relayfs_destroy_inode() along with the relayfs inode cache.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds and exports relayfs_remove_file(), for API symmetry (with
relayfs_create_file()).
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds a mandatory fileops param to relayfs_create_file() and exports
that function so that clients can use it to create files defined by their own
set of file operations, in relayfs. The purpose is to allow relayfs
applications to create their own set of 'control' files alongside their relay
files in relayfs rather than having to create them in /proc or debugfs for
instance. relayfs_create_file() is also used by relay_open_buf() to create
the relay files for a channel. In this case, a pointer to
relayfs_file_operations is passed in, along with a pointer to the buffer
associated with the file.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Needed for the Novell kernel debugger and perhaps some per-cpu data on x86_64
in the future.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use atomic_inc_not_zero for rcu files instead of special case rcuref.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch moves the rtc_interrupt() prototype to rtc.h and removes the
prototypes from C files.
It also renames static rtc_interrupt() functions in
arch/arm/mach-integrator/time.c and arch/sh64/kernel/time.c to avoid compile
problems.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Gortmaker <p_gortmaker@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch changes generic_cont_expand(), in order to share the code
with fatfs.
- Use vmtruncate() if ->prepare_write() returns a error.
Even if ->prepare_write() returns an error, it may already have added some
blocks. So, this truncates blocks outside of ->i_size by vmtruncate().
- Add generic_cont_expand_simple().
The generic_cont_expand_simple() assumes that ->prepare_write() can handle
the block boundary. With this, we don't need to care the extra byte.
And for expanding a file size by truncate(), fatfs uses the
added generic_cont_expand_simple().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This exports/changes the sync_page_range/_nolock(). The fatfs needs
sync_page_range/_nolock() for expanding truncate, and changes "size_t count"
to "loff_t count".
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch add to support of ->direct_IO() for mostly read.
The user of this seems to want to use for streaming read. So, current direct
I/O has limitation, it can only overwrite. (For write operation, mainly we
need to handle the hole etc..)
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
New character device driver for the SyncLink GT and SyncLink AC families of
synchronous and asynchronous serial adapters
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove a couple of more lines of code from the cpuset hooks in the page
allocation code path.
There was a check for a NULL cpuset pointer in the routine
cpuset_update_task_memory_state() that was only needed during system boot,
after the memory subsystem was initialized, before the cpuset subsystem was
initialized, to catch a NULL task->cpuset pointer.
Add a cpuset_init_early() routine, just before the mem_init() call in
init/main.c, that sets up just enough of the init tasks cpuset structure to
render cpuset_update_task_memory_state() calls harmless.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix more of longstanding bug in cpuset/mempolicy interaction.
NUMA mempolicies (mm/mempolicy.c) are constrained by the current tasks cpuset
to just the Memory Nodes allowed by that cpuset. The kernel maintains
internal state for each mempolicy, tracking what nodes are used for the
MPOL_INTERLEAVE, MPOL_BIND or MPOL_PREFERRED policies.
When a tasks cpuset memory placement changes, whether because the cpuset
changed, or because the task was attached to a different cpuset, then the
tasks mempolicies have to be rebound to the new cpuset placement, so as to
preserve the cpuset-relative numbering of the nodes in that policy.
An earlier fix handled such mempolicy rebinding for mempolicies attached to a
task.
This fix rebinds mempolicies attached to vma's (address ranges in a tasks
address space.) Due to the need to hold the task->mm->mmap_sem semaphore while
updating vma's, the rebinding of vma mempolicies has to be done when the
cpuset memory placement is changed, at which time mmap_sem can be safely
acquired. The tasks mempolicy is rebound later, when the task next attempts
to allocate memory and notices that its task->cpuset_mems_generation is
out-of-date with its cpusets mems_generation.
Because walking the tasklist to find all tasks attached to a changing cpuset
requires holding tasklist_lock, a spinlock, one cannot update the vma's of the
affected tasks while doing the tasklist scan. In general, one cannot acquire
a semaphore (which can sleep) while already holding a spinlock (such as
tasklist_lock). So a list of mm references has to be built up during the
tasklist scan, then the tasklist lock dropped, then for each mm, its mmap_sem
acquired, and the vma's in that mm rebound.
Once the tasklist lock is dropped, affected tasks may fork new tasks, before
their mm's are rebound. A kernel global 'cpuset_being_rebound' is set to
point to the cpuset being rebound (there can only be one; cpuset modifications
are done under a global 'manage_sem' semaphore), and the mpol_copy code that
is used to copy a tasks mempolicies during fork catches such forking tasks,
and ensures their children are also rebound.
When a task is moved to a different cpuset, it is easier, as there is only one
task involved. It's mm->vma's are scanned, using the same
mpol_rebind_policy() as used above.
It may happen that both the mpol_copy hook and the update done via the
tasklist scan update the same mm twice. This is ok, as the mempolicies of
each vma in an mm keep track of what mems_allowed they are relative to, and
safely no-op a second request to rebind to the same nodes.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Easy little optimization hack to avoid actually having to call
cpuset_zone_allowed() and check mems_allowed, in the main page allocation
routine, __alloc_pages(). This saves several CPU cycles per page allocation
on systems not using cpusets.
A counter is updated each time a cpuset is created or removed, and whenever
there is only one cpuset in the system, it must be the root cpuset, which
contains all CPUs and all Memory Nodes. In that case, when the counter is
one, all allocations are allowed.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Cleanup, reorganize and make more robust the mempolicy.c code to rebind
mempolicies relative to the containing cpuset after a tasks memory placement
changes.
The real motivator for this cleanup patch is to lay more groundwork for the
upcoming patch to correctly rebind NUMA mempolicies that are attached to vma's
after the containing cpuset memory placement changes.
NUMA mempolicies are constrained by the cpuset their task is a member of.
When either (1) a task is moved to a different cpuset, or (2) the 'mems'
mems_allowed of a cpuset is changed, then the NUMA mempolicies have embedded
node numbers (for MPOL_BIND, MPOL_INTERLEAVE and MPOL_PREFERRED) that need to
be recalculated, relative to their new cpuset placement.
The old code used an unreliable method of determining what was the old
mems_allowed constraining the mempolicy. It just looked at the tasks
mems_allowed value. This sort of worked with the present code, that just
rebinds the -task- mempolicy, and leaves any -vma- mempolicies broken,
referring to the old nodes. But in an upcoming patch, the vma mempolicies
will be rebound as well. Then the order in which the various task and vma
mempolicies are updated will no longer be deterministic, and one can no longer
count on the task->mems_allowed holding the old value for as long as needed.
It's not even clear if the current code was guaranteed to work reliably for
task mempolicies.
So I added a mems_allowed field to each mempolicy, stating exactly what
mems_allowed the policy is relative to, and updated synchronously and reliably
anytime that the mempolicy is rebound.
Also removed a useless wrapper routine, numa_policy_rebind(), and had its
caller, cpuset_update_task_memory_state(), call directly to the rewritten
policy_rebind() routine, and made that rebind routine extern instead of
static, and added a "mpol_" prefix to its name, making it
mpol_rebind_policy().
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide a cpuset_mems_allowed() method, which the sys_migrate_pages() code
needed, to obtain the mems_allowed vector of a cpuset, and replaced the
workaround in sys_migrate_pages() to call this new method.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The important code paths through alloc_pages_current() and alloc_page_vma(),
by which most kernel page allocations go, both called
cpuset_update_current_mems_allowed(), which in turn called refresh_mems().
-Both- of these latter two routines did a tasklock, got the tasks cpuset
pointer, and checked for out of date cpuset->mems_generation.
That was a silly duplication of code and waste of CPU cycles on an important
code path.
Consolidated those two routines into a single routine, called
cpuset_update_task_memory_state(), since it updates more than just
mems_allowed.
Changed all callers of either routine to call the new consolidated routine.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Provide a simple per-cpuset metric of memory pressure, tracking the -rate-
that the tasks in a cpuset call try_to_free_pages(), the synchronous
(direct) memory reclaim code.
This enables batch managers monitoring jobs running in dedicated cpusets to
efficiently detect what level of memory pressure that job is causing.
This is useful both on tightly managed systems running a wide mix of
submitted jobs, which may choose to terminate or reprioritize jobs that are
trying to use more memory than allowed on the nodes assigned them, and with
tightly coupled, long running, massively parallel scientific computing jobs
that will dramatically fail to meet required performance goals if they
start to use more memory than allowed to them.
This patch just provides a very economical way for the batch manager to
monitor a cpuset for signs of memory pressure. It's up to the batch
manager or other user code to decide what to do about it and take action.
==> Unless this feature is enabled by writing "1" to the special file
/dev/cpuset/memory_pressure_enabled, the hook in the rebalance
code of __alloc_pages() for this metric reduces to simply noticing
that the cpuset_memory_pressure_enabled flag is zero. So only
systems that enable this feature will compute the metric.
Why a per-cpuset, running average:
Because this meter is per-cpuset, rather than per-task or mm, the
system load imposed by a batch scheduler monitoring this metric is
sharply reduced on large systems, because a scan of the tasklist can be
avoided on each set of queries.
Because this meter is a running average, instead of an accumulating
counter, a batch scheduler can detect memory pressure with a single
read, instead of having to read and accumulate results for a period of
time.
Because this meter is per-cpuset rather than per-task or mm, the
batch scheduler can obtain the key information, memory pressure in a
cpuset, with a single read, rather than having to query and accumulate
results over all the (dynamically changing) set of tasks in the cpuset.
A per-cpuset simple digital filter (requires a spinlock and 3 words of data
per-cpuset) is kept, and updated by any task attached to that cpuset, if it
enters the synchronous (direct) page reclaim code.
A per-cpuset file provides an integer number representing the recent
(half-life of 10 seconds) rate of direct page reclaims caused by the tasks
in the cpuset, in units of reclaims attempted per second, times 1000.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Finish converting mm/mempolicy.c from bitmaps to nodemasks. The previous
conversion had left one routine using bitmaps, since it involved a
corresponding change to kernel/cpuset.c
Fix that interface by replacing with a simple macro that calls nodes_subset(),
or if !CONFIG_CPUSET, returns (1).
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <christoph@lameter.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
configurable replacement for slab allocator
This adds a CONFIG_SLAB option under CONFIG_EMBEDDED. When CONFIG_SLAB is
disabled, the kernel falls back to using the 'SLOB' allocator.
SLOB is a traditional K&R/UNIX allocator with a SLAB emulation layer,
similar to the original Linux kmalloc allocator that SLAB replaced. It's
signicantly smaller code and is more memory efficient. But like all
similar allocators, it scales poorly and suffers from fragmentation more
than SLAB, so it's only appropriate for small systems.
It's been tested extensively in the Linux-tiny tree. I've also
stress-tested it with make -j 8 compiles on a 3G SMP+PREEMPT box (not
recommended).
Here's a comparison for otherwise identical builds, showing SLOB saving
nearly half a megabyte of RAM:
$ size vmlinux*
text data bss dec hex filename
3336372 529360 190812 4056544 3de5e0 vmlinux-slab
3323208 527948 190684 4041840 3dac70 vmlinux-slob
$ size mm/{slab,slob}.o
text data bss dec hex filename
13221 752 48 14021 36c5 mm/slab.o
1896 52 8 1956 7a4 mm/slob.o
/proc/meminfo:
SLAB SLOB delta
MemTotal: 27964 kB 27980 kB +16 kB
MemFree: 24596 kB 25092 kB +496 kB
Buffers: 36 kB 36 kB 0 kB
Cached: 1188 kB 1188 kB 0 kB
SwapCached: 0 kB 0 kB 0 kB
Active: 608 kB 600 kB -8 kB
Inactive: 808 kB 812 kB +4 kB
HighTotal: 0 kB 0 kB 0 kB
HighFree: 0 kB 0 kB 0 kB
LowTotal: 27964 kB 27980 kB +16 kB
LowFree: 24596 kB 25092 kB +496 kB
SwapTotal: 0 kB 0 kB 0 kB
SwapFree: 0 kB 0 kB 0 kB
Dirty: 4 kB 12 kB +8 kB
Writeback: 0 kB 0 kB 0 kB
Mapped: 560 kB 556 kB -4 kB
Slab: 1756 kB 0 kB -1756 kB
CommitLimit: 13980 kB 13988 kB +8 kB
Committed_AS: 4208 kB 4208 kB 0 kB
PageTables: 28 kB 28 kB 0 kB
VmallocTotal: 1007312 kB 1007312 kB 0 kB
VmallocUsed: 48 kB 48 kB 0 kB
VmallocChunk: 1007264 kB 1007264 kB 0 kB
(this work has been sponsored in part by CELF)
From: Ingo Molnar <mingo@elte.hu>
Fix 32-bitness bugs in mm/slob.c.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The latest set of signal-RCU patches does not use get_task_struct_rcu().
Attached is a patch that removes it.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
RCU tasklist_lock and RCU signal handling: send signals RCU-read-locked
instead of tasklist_lock read-locked. This is a scalability improvement on
SMP and a preemption-latency improvement under PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: William Irwin <wli@holomorphy.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Most of the architectures have the same asm/futex.h. This consolidates them
into asm-generic, with the arches including it from their own asm/futex.h.
In the case of UML, this reverts the old broken futex.h and goes back to using
the same one as almost everyone else.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Kill L1_CACHE_SHIFT from all arches. Since L1_CACHE_SHIFT_MAX is not used
anymore with the introduction of INTERNODE_CACHE, kill L1_CACHE_SHIFT_MAX.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
macros
____cacheline_maxaligned_in_smp is currently used to align critical structures
and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find
L1_CACHE_SHIFT_MAX useless.
However, we have been using ____cacheline_maxaligned_in_smp to align
structures on the internode cacheline size. As per Andi's suggestion,
following patch kills ____cacheline_maxaligned_in_smp and introduces
INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches.
Arches needing L3/Internode cacheline alignment can define
INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces
____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp
With this patch, L1_CACHE_SHIFT_MAX can be killed
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a number of miscellanous items:
(1) Declare lock sections in the linker script.
(2) Recurse in the correct manner in the arch makefile.
(3) asm/bug.h requires asm/linkage.h to be included first. One C file puts
asm/bug.h first.
(4) Add an empty RTC header file to avoid missing header file errors.
(5) sg_dma_address() should use the dma_address member of a scatter list.
(6) Add trivial pci_unmap support.
(7) Add pgprot_noncached()
(8) Discard u_quad_t.
(9) Use ~0UL rather than ULONG_MAX in unistd.h in case the latter isn't
declared.
(10) Add an empty VGA header file to avoid missing header file errors.
(11) Add an XOR header file to use the generic XOR stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make the get_user macro cast the source pointer to an appropriate type for the
specified size.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add stubs for FRV module support.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Supply various I/O access primitives that are missing for the FRV arch:
(*) mmiowb()
(*) read*_relaxed()
(*) ioport_*map()
(*) ioread*(), iowrite*(), ioread*_rep() and iowrite*_rep()
(*) pci_io*map()
(*) check_signature()
The patch also makes __is_PCI_addr() more efficient.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
