| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Adds a new scsi_device flag, start_stop_pwr_cond: If enabled, the sd
driver will not send plain START STOP UNIT commands but ones with the
power condition field set to 3 (standby) or 1 (active) respectively.
Some FireWire disk firmwares do not stop the motor if power condition is
zero. Or worse, they become unresponsive after a START STOP UNIT with
power condition = 0 and start = 0.
http://lkml.org/lkml/2008/4/29/704
This patch only adds the necessary code to sd_mod but doesn't activate
it. Follow-up patches to the FireWire drivers will add detection of
affected devices and enable the code for them.
I did not add power condition values to scsi_error.c::scsi_eh_try_stu()
for now. The three firmwares which suffer from above mentioned problems
do not need START STOP UNIT in the error handler, and they are not
adversely affected by START STOP UNIT with power condition = 0 and start
= 1 (like scsi_eh_try_stu() sends it if scsi_device.allow_restart is
enabled).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
|
|
|
|
|
|
|
|
Most likely it is broken anyway because of the changes in memory
detection. Since we can't test it and there are probably better ways
that using a P390 card, remove support for it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Move memory detection code to own file and also simplify it.
Also add an interface which can be called at any time to get the
current memory layout. This interface is needed by our kernel
internal system dumper.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Some macros in pgtable.h access members from struct task_struct.
Currently always works since sched.h seems always to be included
before asm/pgtable.h. Unfortunately that is not anymore true with
Jeremy Fitzhardinge's ptep_modify_prot transaction abstraction patch.
So fix this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add support for new micro code load of CEX2C and CEX2A adapters,
which uses different IDs. This patch just adds the IDs to the
existing drivers.
Signed-off-by: Ralph Wuerthner <ralph.wuerthner@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Now it is possible to specify additional kernel parameters on the IPL
command line using the IPL PARM option.
If the Linux system is already running, the new reipl sysfs attribute
'parm' can be used to change kernel parameters for the next reboot.
Examples:
IPL C PARM dasd=1234 root=/dev/dasda1
IPL 1234 PARM savesys=mylnxnss
echo "init=/bin/bash" > /sys/firmware/reipl/ccw/parm
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
The idle notifier chain consists of at most one element. So there's
no point in having a notifier chain. Remove it and directly call the
function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch adds a driver for subchannels of type chsc.
A device /dev/chsc is created which may be used to issue ioctls to:
- obtain information about the machine's I/O configuration
- dynamically change the machine's I/O configuration via
asynchronous chsc commands
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
css_device_id exists, so use it for determining the right driver
(and add a match_flags which is always 1 for valid types).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
This interface makes it easy for drivers to register usage of different
I/O interruption subclasses without needing to worry about possible
other users of the same isc.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Enhance the adapter interruption API so that device drivers can
register a handler for a specific interruption subclass. This
will allow different device drivers to move to differently
prioritized subclasses in order to avoid congestion.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Replace the numeric values for I/O interruption subclass usage
with abstract definitions and collect them all in asm/isc.h.
This gives us a better overview of which iscs are actually used
and makes it possible to better spread out isc usage in the
future.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Add support for clock synchronization with the server time protocol.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Add the user_regset definitions for normal and compat processes, replace
the dump_regs core dump cruft with the generic CORE_DUMP_USER_REGSET and
replace binfmt_elf32.c with the generic compat_binfmt_elf.c implementation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Provide functions which can be used to incrementally construct fcx
enabled I/O control blocks.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Provide functions for assembling and starting fcx enabled I/O request
blocks.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Extend the scsw data structure to the format required by fcx. Also
provide helper functions for easier access to fields which are present
in both the traditional as well as the modified format.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Add modalias and subchannel type attributes for all subchannels.
I/O subchannel specific attributes are now created in
io_subchannel_probe(). modalias and subchannel type are also
added to the uevent for the css bus. Also make the css modalias
known.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
keep the one for VSYSCALL_HPET
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch adds a new ALSA driver for the audio device found inside
most of the SGI O2 workstation. The hardware uses a SGI custom chip,
which feeds a AD codec chip.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
The register security hook is no longer required, as the capability
module is always registered. LSMs wishing to stack capability as
a secondary module should do so explicitly.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The sb_get_mnt_opts() hook is unused, and is superseded by the
sb_show_options() hook.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: James Morris <jmorris@namei.org>
|
|
This patch causes SELinux mount options to show up in /proc/mounts. As
with other code in the area seq_put errors are ignored. Other LSM's
will not have their mount options displayed until they fill in their own
security_sb_show_options() function.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Enable security modules to distinguish reading of process state via
proc from full ptrace access by renaming ptrace_may_attach to
ptrace_may_access and adding a mode argument indicating whether only
read access or full attach access is requested. This allows security
modules to permit access to reading process state without granting
full ptrace access. The base DAC/capability checking remains unchanged.
Read access to /proc/pid/mem continues to apply a full ptrace attach
check since check_mem_permission() already requires the current task
to already be ptracing the target. The other ptrace checks within
proc for elements like environ, maps, and fds are changed to pass the
read mode instead of attach.
In the SELinux case, we model such reading of process state as a
reading of a proc file labeled with the target process' label. This
enables SELinux policy to permit such reading of process state without
permitting control or manipulation of the target process, as there are
a number of cases where programs probe for such information via proc
but do not need to be able to control the target (e.g. procps,
lsof, PolicyKit, ConsoleKit). At present we have to choose between
allowing full ptrace in policy (more permissive than required/desired)
or breaking functionality (or in some cases just silencing the denials
via dontaudit rules but this can hide genuine attacks).
This version of the patch incorporates comments from Casey Schaufler
(change/replace existing ptrace_may_attach interface, pass access
mode), and Chris Wright (provide greater consistency in the checking).
Note that like their predecessors __ptrace_may_attach and
ptrace_may_attach, the __ptrace_may_access and ptrace_may_access
interfaces use different return value conventions from each other (0
or -errno vs. 1 or 0). I retained this difference to avoid any
changes to the caller logic but made the difference clearer by
changing the latter interface to return a bool rather than an int and
by adding a comment about it to ptrace.h for any future callers.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Manual fixup of include/asm-powerpc/pgtable-ppc64.h
|
|
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* Strengthen the return type for the _node_to_cpumask_ptr to be
a const pointer. This adds compiler checking to insure that
node_to_cpumask_map[] is not changed inadvertently.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
got this on a test-system:
calling numaq_tsc_disable+0x0/0x39
NUMAQ: disabling TSC
initcall numaq_tsc_disable+0x0/0x39 returned 0 after 0 msecs
that's because we should not be using arch_initcall to call numaq_tsc_disable.
need to call it in setup_arch before time_init()/tsc_init()
and call it in init_intel() to make the cpu feature bits right.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix ldt limit for 64 bit
|
|
Fix FRV irqs_disabled() to return an int, not an unsigned long to avoid
this warning:
kernel/sched.c: In function '__might_sleep':
kernel/sched.c:8198: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Move the accessor functions for the scsi_cmnd status from zfcp to the
SCSI include file. Change the interface to the functions to pass the
scsi_cmnd pointer instead of the status pointer.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Adds support for target reset to SG_SCSI_RESET.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The SCSI Block Protocol uses this 16-bit CRC to verify the integrity
of each data sector. crc_t10dif() is used by sd_dif.c when performing
I/O to or from disks formatted with protection information.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Christoph objected to having sd.h in include/scsi since it is internal
to the sd driver. Move it to drivers/scsi/sd.h.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Let through upto the largest command of 260 defined by the scsi standard.
iscsi core supports this already. Now that the scsi-ml supports it we can
start using large commands.
[jejb:rejections fixed up]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Drivers expect that the cmds_max value they pass to the iscsi layer
is the max scsi commands + mgmt tasks. This patch implements that
and fixes some checks for nr cmd limits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add sysfs representation for the endpoint, so userspace can match the
host and session to the endpoint. This will allow us to set the host's
parent correctly at host creation time.
The next patches will convert tcp and iser, and fix iser's dma_mask
bug.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
session list
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This is the second part of the iscsi task merging, and
all it does it rename iscsi_cmd_task to iscsi_task and
mtask/ctask to just task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
