| Age | Commit message (Collapse) | Author |
|---|
|
Sibyte SOCs only have 32-bit PCI. Due to the sparse use of the address
space only the first 1GB of memory is mapped at physical addresses
below 1GB. If a system has more than 1GB of memory 32-bit DMA will
not be able to reach all of it.
For now this patch is good enough to keep Sibyte users happy but it seems
eventually something like swiotlb will be needed for Sibyte.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The R4000 and R4400 have an errata where if the cp0 count register is read
in the exact moment when it matches the compare register no interrupt will
be generated.
This bug may be triggered if the cp0 count register is being used as
clocksource and the compare interrupt as clockevent. So a simple
workaround is to avoid using the compare for both facilities on the
affected CPUs.
This is different from the workaround suggested in the old errata documents;
at some opportunity probably the official version should be implemented
and tested. Another thing to find out is which processor versions
exactly are affected. I only have errata documents upto R4400 V3.0
available so for the moment the code treats all R4000 and R4400 as broken.
This is potencially a problem for some machines that have no other decent
clocksource available; this workaround will cause them to fall back to
another clocksource, worst case the "jiffies" source.
|
|
The LL / SC loops in __futex_atomic_op() have the usual fixups necessary
for memory acccesses to userspace from kernel space installed:
__asm__ __volatile__(
" .set push \n"
" .set noat \n"
" .set mips3 \n"
"1: ll %1, %4 # __futex_atomic_op \n"
" .set mips0 \n"
" " insn " \n"
" .set mips3 \n"
"2: sc $1, %2 \n"
" beqz $1, 1b \n"
__WEAK_LLSC_MB
"3: \n"
" .set pop \n"
" .set mips0 \n"
" .section .fixup,\"ax\" \n"
"4: li %0, %6 \n"
" j 2b \n" <-----
" .previous \n"
" .section __ex_table,\"a\" \n"
" "__UA_ADDR "\t1b, 4b \n"
" "__UA_ADDR "\t2b, 4b \n"
" .previous \n"
: "=r" (ret), "=&r" (oldval), "=R" (*uaddr)
: "0" (0), "R" (*uaddr), "Jr" (oparg), "i" (-EFAULT)
: "memory");
The branch at the end of the fixup code, it goes back to the SC
instruction, no matter if the fault was first taken by the LL or SC
instruction resulting in an endless loop which will only terminate if
the address become valid again due to another thread setting up an
accessible mapping and the CPU happens to execute the SC instruction
successfully which due to the preceeding ERET instruction of the fault
handler would only happen if UNPREDICTABLE instruction behaviour of the
SC instruction without a preceeding LL happens to favor that outcome.
But normally processes are nice, pass valid arguments and we were just
getting away with this.
Thanks to Kaz Kylheku <kaz@zeugmasystems.com> for providing the original
report and a test case.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A new born thread starts execution not in schedule but rather in
ret_from_fork which results in it bypassing the part of the code to
load a new context written in C which are the DSP context and the
userlocal register which Linux uses for the TLS pointer. Frequently
we were just getting away with this bug for a number of reasons:
o Real world application scenarios are very unlikely to use clone or fork
in blocks of DSP code.
o Linux by default runs the child process right after the fork, so the
child by luck will find all the right context in the DSP and userlocal
registers.
o So far the rdhwr instruction was emulated on all hardware so userlocal
wasn't getting referenced at all and the emulation wasn't suffering
from the issue since it gets it's value straight from the thread's
thread_info.
Fixed by moving the code to load the context from switch_to() to
finish_arch_switch which will be called by newborn and old threads.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The skb_morph function only freed the data part of the dst skb, but leaked
the auxiliary data such as the netfilter fields. This patch fixes this by
moving the relevant parts from __kfree_skb to skb_release_all and calling
it in skb_morph.
It also makes kfree_skbmem static since it's no longer called anywhere else
and it now no longer does skb_release_data.
Thanks to Yasuyuki KOZAKAI for finding this problem and posting a patch for
it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
1. update default MFPR value to drive strength fast 3mA and edge
detection logic disabled
2. update impacted MFP_CFG_xxx() macros
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
add missing IRQ_xxx definitions for PXA3xx
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
x = vmalloc(...);
else
#endif
x = kmalloc(...);
Unlike it, the inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
vfree(x);
else
#else
kfree(x);
#endif
The error is obvious - if the NUMA is on and the size
is less than the PAGE_SIZE we leak the pointer (kfree is
inside the #else branch).
Compiler doesn't warn us because after the kfree(x) there's
a "x = NULL" assignment, so here's another (minor?) bug: we
don't set x to NULL under certain circumstances.
Boring explanation, I know... Patch explains it better.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
xs_setup_{udp,tcp}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
process.c, which was largely duplicated
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
common sound code otherwise
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Should not need separate cplb entry though as we cover L1 with a 4 meg page
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
- remove duplicated defines for the BF561
- generalize L2 support (so that it works for BF54x) and mark it executable
- add support for reading/executing the Boot ROM sections
(since it has data/functions we may need at runtime)
- and fixup names for each map
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
- no need to declare their sizes in the common header
- no need to tack on the section attribute as only the definition matters, not references
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
L1_SCRATCH defines
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Anomaly 05000312 - Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted:
DESCRIPTION:
When instruction cache is enabled, erroneous behavior may occur when any of the following instructions are interrupted:
. CSYNC
• SSYNC
• LCx =
• LTx = (only when LCx is non-zero)
• LBx = (only when LCx is non-zero)
When this problem occurs, a variety of incorrect things could happen, including an illegal instruction exception. Additional errors could
show up as an exception, a hardware error, or an instruction that is valid but different than the one that was expected.
WORKAROUND:
Place a cli before all SSYNC, CSYNC, "LCx =", "LTx =", and "LBx =" instructions to disable interrupts, and place an sti after each of these
instructions to re-enable interrupts. When these instructions are executed in code that is already non-interruptible, the problem will not
occur.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
and export it
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
defined
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
if (net_ratelimit())
IEEE80211_DEBUG_DROP(...)
can pollute the logs with messages like:
printk: 1 messages suppressed.
printk: 2 messages suppressed.
printk: 7 messages suppressed.
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Remove binary sysctls that never worked due to missing strategy functions.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove binary sysctls that never worked due to missing strategy functions.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Use mp_irqs[] to get PNP device's interrupt polarity and trigger.
There are two reasons to do this:
1. BIOS bug for PNP interrupt
2. BIOS explictly does override
mp_irqs[] should cover all the cases.
http://bugzilla.kernel.org/show_bug.cgi?id=5243
http://bugzilla.kernel.org/show_bug.cgi?id=7679
http://bugzilla.kernel.org/show_bug.cgi?id=9153
[lenb: fixed !IOAPIC and 64-bit !SMP builds]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl table check failed: /net/ipv4/vs/lblc_expiration .3.5.21.19 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/lblcr_expiration .3.5.21.20 Missing strategy
Switch these entried over to use CTL_UNNUMBERED as clearly
the sys_syscal portion wasn't working.
This is along the same lines as Christian Borntraeger's patch that fixes
up entries with no stratergy in net/ipv4/ipvs/ip_vs_ctl.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The current VDSO implementation is hardcoded to 128 byte cache blocks,
which are only used on IBM's 64-bit processors.
Convert it to get the cache block sizes out of vdso_data instead,
similar to how the ppc64 in-kernel cache flush does it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355
cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
On platforms doing non-coherent DMA (4xx, 8xx, ...), it's important
that the kmalloc minimum alignment is set to the cache line size, to
avoid sharing cache lines between different objects, so that DMA to
one of the objects doesn't corrupt the other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
pcibios_free_controller() is now available for both 32 and 64 bits
but the header only declares it for 64 bits. This moves the
declaration down next to the pcibios_alloc_controller() one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Heiko Schocher <heiko.schocher@invitel.hu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
This patch removes the following obsolete functions:
- libata-core.c: __sata_phy_reset()
- libata-core.c: sata_phy_reset()
- libata-eh.c: ata_qc_timeout()
- libata-eh.c: ata_eng_timeout()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Indeed my previous change to alloc_pskb has made it possible
for the TCP header to be misaligned iff the MTU is not a multiple
of 4 (and less than a page). So I suspect the optimised IPsec
MTU calculation is giving you just such an MTU :)
This patch fixes it by changing alloc_pskb to make sure that
the size is at least 32-bit aligned. This does not cause the
problem fixed by the previous patch because max_header is always
32-bit aligned which means that in the SG/NOTSO case this will
be a no-op.
I thought about putting this in the callers but all the current
callers are from TCP. If and when we get a non-TCP caller we
can always create a TCP wrapper for this function and move the
alignment over there.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
assembly.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
/*
* CPUs often take a performance hit when accessing unaligned memory
* locations. The actual performance hit varies, it can be small if the
* hardware handles it or large if we have to take an exception and fix
* it
* in software.
*
* Since an ethernet header is 14 bytes network drivers often end up
* with
* the IP header at an unaligned offset. The IP header can be aligned by
* shifting the start of the packet by 2 bytes. Drivers should do this
* with:
*
* skb_reserve(NET_IP_ALIGN);
*
* The downside to this alignment of the IP header is that the DMA is
* now
* unaligned. On some architectures the cost of an unaligned DMA is high
* and this cost outweighs the gains made by aligning the IP header.
*
* Since this trade off varies between architectures, we allow
* NET_IP_ALIGN
* to be overridden.
*/
This new function insl_16 allows to read form 32-bit IO and writes to
16-bit aligned memory. This is useful in above described scenario -
In particular with the AXIS AX88180 Gigabit Ethernet MAC.
Once the device is in 32-bit mode, reads from the RX FIFO always
decrements 4bytes.
While on the other side the destination address in SDRAM is always
16-bit aligned.
If we use skb_reserve(0) the receive buffer is 32-bit aligned but later
we hit a unaligned exception in the IP code.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Attempt to fix http://bugzilla.kernel.org/show_bug.cgi?id=8378
Hiroto Shibuya wrote to tell me that he has a VIA EPIA-EK10000 which
suffers from the reboot problem when no keyboard is attached. My first
patch works for him:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=59f4e7d572980a521b7bdba74ab71b21f5995538
But the latest patch does not work for him :
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=8b93789808756bcc1e5c90c99f1b1ef52f839a51
We found that it was necessary to also set the "disable keyboard" flag in
the command byte, as the first patch was doing. The second patch tries to
minimally modify the command byte, but it is not enough.
Please consider this simple one-line patch to help people with low end VIA
motherboards reboot when no keyboard is attached. Hiroto Shibuya has
verified that this works for him (as I no longer have an afflicted
machine).
Additional discussion:
Note that original patch from Truxton DOES
disable keyboard and this has been in main tree since 2.6.14, thus it must have
quite a bit of air time already.
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.14.y.git;a=commit;h=59f4e7d572980a521b7bdba74ab71b21f5995538
Note that he only mention "System flag" in the description and comment, but
in the code, "disable keyboard" flag is set.
outb(0x14, 0x60); /* set "System flag" */
In 2.6.23, he made a change to read the current byte and then mask the flags,
but along this change, he only set the "System flag" and dropped the setting
of "disable keyboard" flag.
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.23.y.git;a=commit;h=8b93789808756bcc1e5c90c99f1b1ef52f839a51
outb(cmd | 0x04, 0x60); /* set "System flag" */
So my request is to restore the setting of disable keyboard flag which has been
there since 2.6.14 but disappeared in 2.6.23.
Cc: Lee Garrett <lee-in-berlin@web.de>
Cc: "Hiroto Shibuya" <hiroto.shibuya@gmail.com>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Aristeu Rozanski <aris@ruivo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix header file name for Voyager build.
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-voyager/setup_arch.h:2:26: error: asm/setup_32.h: No such file or directory
make[1]: *** [arch/x86/kernel/setup_32.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
