| Age | Commit message (Collapse) | Author |
|---|
|
Speedup module unloading by factorizing synchronize_rcu() calls
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Speedup module unloading by factorizing synchronize_rcu() calls
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use unregister_netdevice_many() to speedup master device unregister.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a list_head parameter to rtnl_link_ops->dellink() methods
allow us to queue devices on a list, in order to dismantle
them all at once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce rollback_registered_many() and unregister_netdevice_many()
rollback_registered_many() is able to perform necessary steps at device dismantle
time, factorizing two expensive synchronize_net() calls.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patchs adds an unreg_list anchor to struct net_device, and
introduces an unregister_netdevice_queue() function, able to queue
a net_device to a list instead of immediately unregister it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes the mesh housekeeping timer work properly on big endian
systems.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mesh portals proxy traffic for nodes external to the mesh. When a
proxied frame is received by a mesh interface, it should update its mesh
portal table. This was only happening for unicast frames. With this
change we also learn about mesh portals from proxied multicast frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace netif_tx_{start,stop,wake}_all_queues with the single-queue
equivalents (i.e. netif_{start,stop,wake}_queue). Since we are down to
a single queue, these should peform slightly better.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It might be the case that __cfg80211_disconnected() has already
cleaned up wdev->current_bss() for us. The old code didn't catch
that situation and didn't warn needlessly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Get rid of cookies in cfg80211_send_XXX() functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.
A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix a typo in the description of hwmp_route_info_get(), no function
changes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the in-kernel SME gets an association failure from
the AP we don't deauthenticate, and thus get into a very
confused state which will lead to warnings later on. Fix
this by actually deauthenticating when the AP indicates
an association failure.
(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When association fails, we should stay authenticated,
which in mac80211 is represented by the existence of
the mlme work struct, so we cannot free that, instead
we need to just set it to idle.
(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Recent commit "mac80211: fix logic error ibss merge bssid check" fixed
joining of ibss cell when static bssid is provided. In this case
ifibss->bssid is set before the cell is joined and comparing that address
to a bss should thus always succeed. Unfortunately this change broke the
other case of joining a ibss cell without providing a static bssid where
the value of ifibss->bssid is not set before the cell is joined.
Since ifibss->bssid may be set before or after joining the cell we do not
learn anything by comparing it to a known bss. Remove this check.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/sh_eth.c
|
|
We currently use a 16 bit field (vlan_tci) to store VLAN ID/PRIO on a skb.
Null value is used as a special value, meaning vlan tagging not enabled.
This forbids use of null vlan ID.
As pointed by David, some drivers use the 3 high order bits (PRIO)
As VLAN ID is 12 bits, we can use the remaining bit (CFI) as a flag, and
allow null VLAN ID.
In case future code really wants to use VLAN_CFI_MASK, we'll have to use
a bit outside of vlan_tci.
#define VLAN_PRIO_MASK 0xe000 /* Priority Code Point */
#define VLAN_PRIO_SHIFT 13
#define VLAN_CFI_MASK 0x1000 /* Canonical Format Indicator */
#define VLAN_TAG_PRESENT VLAN_CFI_MASK
#define VLAN_VID_MASK 0x0fff /* VLAN Identifier */
Reported-by: Gertjan Hofman <gertjan_hofman@yahoo.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While playing with pktgen, I realized IP ID was not filled and a
random value was taken, possibly leaking 2 bytes of kernel memory.
We can use an increasing ID, this can help diagnostics anyway.
Also clear packet payload, instead of leaking kernel memory.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling large number of netdevice, rtnl_dump_ifinfo()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table.
This considerably speedups "ip link" operations
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRE tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPIP tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xfrm6_tunnels use one rwlock to protect their hash tables.
Plain and straightforward conversion to RCU locking to permit better SMP
performance.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIT tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIT tunnels use one rwlock to protect their prl entries.
This first patch adds RCU locking for prl management,
with standard call_rcu() calls.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for setting the skb mark.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b6b39e8f3fbbb (tcp: Try to catch MSG_PEEK bug) added a printk()
to the WARN_ON() that's in tcp.c. This patch changes this combination
to WARN(); the advantage of WARN() is that the printk message shows up
inside the message, so that kerneloops.org will collect the message.
In addition, this gets rid of an extra if() statement.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_getlink() & rtnl_setlink() run with RTNL held, we can use
__dev_get_by_index() and __dev_get_by_name() variants and avoid
dev_hold()/dev_put()
Adds to rtnl_getlink() the capability to find a device by its name,
not only by its index.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For connected sockets, the first run of dev_pick_tx saves the
calculated txq in sk_tx_queue_mapping. This is not saved if
either the device has a queue select or the socket is not
connected. Next iterations of dev_pick_tx uses the cached value
of sk_tx_queue_mapping.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dst_negative_advice() should check for changed dst and reset
sk_tx_queue_mapping accordingly. Pass sock to the callers of
dst_negative_advice.
(sk_reset_txq is defined just for use by dst_negative_advice. The
only way I could find to get around this is to move dst_negative_()
from dst.h to dst.c, include sock.h in dst.c, etc)
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6: Reset sk_tx_queue_mapping when dst_cache is reset. Use existing
macro to do the work.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce sk_tx_queue_mapping; and functions that set, test and
get this value. Reset sk_tx_queue_mapping to -1 whenever the dst
cache is set/reset, and in socket alloc. Setting txq to -1 and
using valid txq=<0 to n-1> allows the tx path to use the value
of sk_tx_queue_mapping directly instead of subtracting 1 on every
tx.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can help being able to filter packets on their queue_mapping.
If filter performance is not good, we could add a "numqueue" field
in struct packet_type, so that netif_nit_deliver() and other functions
can directly ignore packets with not expected queue number.
Lets experiment this simple filter extension first.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We hold RTNL, we can use __dev_get_by_index() instead of dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While doing multiple captures, I found af_packet was dirtying cache line
containing its prot_hook.
This slow down machines where several cpus are necessary to handle capture
traffic, as each prot_hook is traversed for each packet coming in or out
the host.
This patches moves "struct packet_type prot_hook" to the end of
packet_sock, and uses a ____cacheline_aligned_in_smp to make sure
this remains shared by all cpus.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch tries to print out more information when we hit the
MSG_PEEK bug in tcp_recvmsg. It's been around since at least
2005 and it's about time that we finally fix it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use symbols instead of magic constants while checking PMTU discovery
setsockopt.
Remove redundant test in ip_rt_frag_needed() (done by caller).
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow bpf to set a filter to drop packets that dont
match a specific mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv4/ipv6 setsockopt(IP_MULTICAST_IF) have dubious __dev_get_by_index() calls.
This function should be called only with RTNL or dev_base_lock held, or reader
could see a corrupt hash chain and eventually enter an endless loop.
Fix is to call dev_get_by_index()/dev_put().
If this happens to be performance critical, we could define a new dev_exist_by_index()
function to avoid touching dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When shutdown ppp connection, lockdep waring about non-static key
will happen, it is caused by the lock is not initialized properly
at that time.
Fix with tuning the lock/skb_queue_head init order
[ 94.339261] INFO: trying to register non-static key.
[ 94.342509] the code is fine but needs lockdep annotation.
[ 94.342509] turning off the locking correctness validator.
[ 94.342509] Pid: 0, comm: swapper Not tainted 2.6.31-mm1 #2
[ 94.342509] Call Trace:
[ 94.342509] [<c0248fbe>] register_lock_class+0x58/0x241
[ 94.342509] [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[ 94.342509] [<c024ab34>] __lock_acquire+0xac/0xb73
[ 94.342509] [<c024b7fa>] ? lock_release_non_nested+0x17b/0x1de
[ 94.342509] [<c024b662>] lock_acquire+0x67/0x84
[ 94.342509] [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[ 94.342509] [<c054a857>] _spin_lock_irqsave+0x2f/0x3f
[ 94.342509] [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[ 94.342509] [<c04cd1eb>] skb_dequeue+0x15/0x41
[ 94.342509] [<c054a648>] ? _read_unlock+0x1d/0x20
[ 94.342509] [<c04cd641>] skb_queue_purge+0x14/0x1b
[ 94.342509] [<fab94fdc>] l2cap_recv_frame+0xea1/0x115a [l2cap]
[ 94.342509] [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[ 94.342509] [<c0249c04>] ? mark_lock+0x1e/0x1c7
[ 94.342509] [<f8364963>] ? hci_rx_task+0xd2/0x1bc [bluetooth]
[ 94.342509] [<fab95346>] l2cap_recv_acldata+0xb1/0x1c6 [l2cap]
[ 94.342509] [<f8364997>] hci_rx_task+0x106/0x1bc [bluetooth]
[ 94.342509] [<fab95295>] ? l2cap_recv_acldata+0x0/0x1c6 [l2cap]
[ 94.342509] [<c02302c4>] tasklet_action+0x69/0xc1
[ 94.342509] [<c022fbef>] __do_softirq+0x94/0x11e
[ 94.342509] [<c022fcaf>] do_softirq+0x36/0x5a
[ 94.342509] [<c022fe14>] irq_exit+0x35/0x68
[ 94.342509] [<c0204ced>] do_IRQ+0x72/0x89
[ 94.342509] [<c02038ee>] common_interrupt+0x2e/0x34
[ 94.342509] [<c024007b>] ? pm_qos_add_requirement+0x63/0x9d
[ 94.342509] [<c038e8a5>] ? acpi_idle_enter_bm+0x209/0x238
[ 94.342509] [<c049d238>] cpuidle_idle_call+0x5c/0x94
[ 94.342509] [<c02023f8>] cpu_idle+0x4e/0x6f
[ 94.342509] [<c0534153>] rest_init+0x53/0x55
[ 94.342509] [<c0781894>] start_kernel+0x2f0/0x2f5
[ 94.342509] [<c0781091>] i386_start_kernel+0x91/0x96
Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to driver core changes dev_set_drvdata will call kzalloc which should be
in might_sleep context, but hci_conn_add will be called in atomic context
Like dev_set_name move dev_set_drvdata to work queue function.
oops as following:
Oct 2 17:41:59 darkstar kernel: [ 438.001341] BUG: sleeping function called from invalid context at mm/slqb.c:1546
Oct 2 17:41:59 darkstar kernel: [ 438.001345] in_atomic(): 1, irqs_disabled(): 0, pid: 2133, name: sdptool
Oct 2 17:41:59 darkstar kernel: [ 438.001348] 2 locks held by sdptool/2133:
Oct 2 17:41:59 darkstar kernel: [ 438.001350] #0: (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.+.}, at: [<faa1d2f5>] lock_sock+0xa/0xc [l2cap]
Oct 2 17:41:59 darkstar kernel: [ 438.001360] #1: (&hdev->lock){+.-.+.}, at: [<faa20e16>] l2cap_sock_connect+0x103/0x26b [l2cap]
Oct 2 17:41:59 darkstar kernel: [ 438.001371] Pid: 2133, comm: sdptool Not tainted 2.6.31-mm1 #2
Oct 2 17:41:59 darkstar kernel: [ 438.001373] Call Trace:
Oct 2 17:41:59 darkstar kernel: [ 438.001381] [<c022433f>] __might_sleep+0xde/0xe5
Oct 2 17:41:59 darkstar kernel: [ 438.001386] [<c0298843>] __kmalloc+0x4a/0x15a
Oct 2 17:41:59 darkstar kernel: [ 438.001392] [<c03f0065>] ? kzalloc+0xb/0xd
Oct 2 17:41:59 darkstar kernel: [ 438.001396] [<c03f0065>] kzalloc+0xb/0xd
Oct 2 17:41:59 darkstar kernel: [ 438.001400] [<c03f04ff>] device_private_init+0x15/0x3d
Oct 2 17:41:59 darkstar kernel: [ 438.001405] [<c03f24c5>] dev_set_drvdata+0x18/0x26
Oct 2 17:41:59 darkstar kernel: [ 438.001414] [<fa51fff7>] hci_conn_init_sysfs+0x40/0xd9 [bluetooth]
Oct 2 17:41:59 darkstar kernel: [ 438.001422] [<fa51cdc0>] ? hci_conn_add+0x128/0x186 [bluetooth]
Oct 2 17:41:59 darkstar kernel: [ 438.001429] [<fa51ce0f>] hci_conn_add+0x177/0x186 [bluetooth]
Oct 2 17:41:59 darkstar kernel: [ 438.001437] [<fa51cf8a>] hci_connect+0x3c/0xfb [bluetooth]
Oct 2 17:41:59 darkstar kernel: [ 438.001442] [<faa20e87>] l2cap_sock_connect+0x174/0x26b [l2cap]
Oct 2 17:41:59 darkstar kernel: [ 438.001448] [<c04c8df5>] sys_connect+0x60/0x7a
Oct 2 17:41:59 darkstar kernel: [ 438.001453] [<c024b703>] ? lock_release_non_nested+0x84/0x1de
Oct 2 17:41:59 darkstar kernel: [ 438.001458] [<c028804b>] ? might_fault+0x47/0x81
Oct 2 17:41:59 darkstar kernel: [ 438.001462] [<c028804b>] ? might_fault+0x47/0x81
Oct 2 17:41:59 darkstar kernel: [ 438.001468] [<c033361f>] ? __copy_from_user_ll+0x11/0xce
Oct 2 17:41:59 darkstar kernel: [ 438.001472] [<c04c9419>] sys_socketcall+0x82/0x17b
Oct 2 17:41:59 darkstar kernel: [ 438.001477] [<c020329d>] syscall_call+0x7/0xb
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix TCP_DEFER_ACCEPT conversion between seconds and
retransmission to match the TCP SYN-ACK retransmission periods
because the time is converted to such retransmissions. The old
algorithm selects one more retransmission in some cases. Allow
up to 255 retransmissions.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change SYN-ACK retransmitting code for the TCP_DEFER_ACCEPT
users to not retransmit SYN-ACKs during the deferring period if
ACK from client was received. The goal is to reduce traffic
during the deferring period. When the period is finished
we continue with sending SYN-ACKs (at least one) but this time
any traffic from client will change the request to established
socket allowing application to terminate it properly.
Also, do not drop acked request if sending of SYN-ACK fails.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Willy Tarreau and many other folks in recent years
were concerned what happens when the TCP_DEFER_ACCEPT period
expires for clients which sent ACK packet. They prefer clients
that actively resend ACK on our SYN-ACK retransmissions to be
converted from open requests to sockets and queued to the
listener for accepting after the deferring period is finished.
Then application server can decide to wait longer for data
or to properly terminate the connection with FIN if read()
returns EAGAIN which is an indication for accepting after
the deferring period. This change still can have side effects
for applications that expect always to see data on the accepted
socket. Others can be prepared to work in both modes (with or
without TCP_DEFER_ACCEPT period) and their data processing can
ignore the read=EAGAIN notification and to allocate resources for
clients which proved to have no data to send during the deferring
period. OTOH, servers that use TCP_DEFER_ACCEPT=1 as flag (not
as a timeout) to wait for data will notice clients that didn't
send data for 3 seconds but that still resend ACKs.
Thanks to Willy Tarreau for the initial idea and to
Eric Dumazet for the review and testing the change.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 6d01a026b7d3009a418326bdcf313503a314f1ea.
Julian Anastasov, Willy Tarreau and Eric Dumazet have come up
with a more correct way to deal with this.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I found a deadlock bug in UNIX domain socket, which makes able to DoS
attack against the local machine by non-root users.
How to reproduce:
1. Make a listening AF_UNIX/SOCK_STREAM socket with an abstruct
namespace(*), and shutdown(2) it.
2. Repeat connect(2)ing to the listening socket from the other sockets
until the connection backlog is full-filled.
3. connect(2) takes the CPU forever. If every core is taken, the
system hangs.
PoC code: (Run as many times as cores on SMP machines.)
int main(void)
{
int ret;
int csd;
int lsd;
struct sockaddr_un sun;
/* make an abstruct name address (*) */
memset(&sun, 0, sizeof(sun));
sun.sun_family = PF_UNIX;
sprintf(&sun.sun_path[1], "%d", getpid());
/* create the listening socket and shutdown */
lsd = socket(AF_UNIX, SOCK_STREAM, 0);
bind(lsd, (struct sockaddr *)&sun, sizeof(sun));
listen(lsd, 1);
shutdown(lsd, SHUT_RDWR);
/* connect loop */
alarm(15); /* forcely exit the loop after 15 sec */
for (;;) {
csd = socket(AF_UNIX, SOCK_STREAM, 0);
ret = connect(csd, (struct sockaddr *)&sun, sizeof(sun));
if (-1 == ret) {
perror("connect()");
break;
}
puts("Connection OK");
}
return 0;
}
(*) Make sun_path[0] = 0 to use the abstruct namespace.
If a file-based socket is used, the system doesn't deadlock because
of context switches in the file system layer.
Why this happens:
Error checks between unix_socket_connect() and unix_wait_for_peer() are
inconsistent. The former calls the latter to wait until the backlog is
processed. Despite the latter returns without doing anything when the
socket is shutdown, the former doesn't check the shutdown state and
just retries calling the latter forever.
Patch:
The patch below adds shutdown check into unix_socket_connect(), so
connect(2) to the shutdown socket will return -ECONREFUSED.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Signed-off-by: Masanori Yoshida <masanori.yoshida.tv@hitachi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last users of skb_icv_walk are converted to ahash now,
so skb_icv_walk is unused and can be removed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts ah6 to the new ahash interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts ah4 to the new ahash interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
