| Age | Commit message (Collapse) | Author |
|---|
|
AD1986A has a hardware problem that it cannot share a stream with
multiple pins properly. The problem occurs e.g. when a volume is changed
during playback.
So far, hda-intel driver unconditionally assigns the stream to multiple
output pins in copy-front mode, and this should be avoided for AD1986A
codec.
The original fix patch was by zhejiang <zhe.jiang@intel.com>.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
dac_nids arrays in each codec support code may have up to 5 items
when assigned from the auto-configurator. Some codec codes have
less numbers than the possible max. This patch defines the constant
and fixes the array definitions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Fixed the build error from patch_sigmatel.c when built without
CONFIG_SND_HDA_GENERIC by defining a dummy function to return error.
Also, clean up hda_codec.c by removing unneeded ifdefs (the compiler
will optimize out).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Added CONFIG_SND_HDA_POWER_SAVE kconfig. It's an experimental option
to achieve an aggressive power-saving. With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'. It specifies
the second of time-out for automatic power-down. As default, it's
10 seconds. Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on. For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off. Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning. This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added snd_hda_codec_amp_stereo() function that changes both of stereo
channels with the same mask and value bits. It simplifies most of
amp-handling codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
So far, the driver looked the table of snd_kcontrol_new used for creating
mixer elements and forces to call each of its put callbacks in PM resume
code. This is too ugly and hackish.
Now, the resume is simplified using the codec amp and command register
caches. The driver simply restores the values that have been written
in the cache table. With this simplification, most codec support codes
don't require any special resume callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds the cache for codec command registers.
snd_hda_codec_write_cache() and snd_hda_sequence_write_cache() do
the write operations with caching, which values can be resumed via
snd_hda_codec_resume_cache().
The patch introduces only the framework, and no codec code is using
this cache yet. It'll be implemented in the following patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added callbacks for a generic bind-control of mixer elements.
This can be used for creating a mixer element controlling multiple
widgets at the same time. Two macros, HDA_BIND_VOL() and HDA_BIND_SW(),
are introduced for creating bind-volume and bind-switch, respectively.
It taks the mixer element name and struct hda_bind_ctls pointer, which
contains the real control callbacks in ops field and long array for
private_value of each bound widget.
All widgets have to be the same type (i.e. the same amp capability).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added a hwdep interface for each codec (enabled per kconfig).
This interface can be used for reading/writing HD-audio verbs
and other purposes as future extensions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix codes to follow more to the standard kernel coding style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
STAC922x provides the capture boost level up to 4, but actually it
works only up to 2. Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand. snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume). This should fix another recording problem on Intel Macs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added line_out_type field to auto_pin_cfg struct to provide the
pin type of default line_outs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix SPDIF output (at least on Realtek codecs). The DIGI_CONVERT verbs
have to be reset before the PCM stream is set up. Otherwise the digital
setup is screwed up.
Also, check the AMP capability before setting AMP of the digital out
widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Use global workqueue for simplicity.
The unsolicited event frequency isn't so high to have own queue.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Use snd_pci_quirk_lookup() for looking up a board config table.
The config table is sorted in numerical order of PCI SSIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix up for make allyesconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
Some machines have multiple headpohne pins (usually on the lpatop
and on the docking station) while the current hda-codec driver
assumes a single headphone pin. Now it supports multiple hp pins
(at least for detection).
The sigmatel 92xx code supports this new multiple hp pins.
It detects all hp pins for auto-muting, too.
Also, the driver checks speaker pins in addition. In some cases,
all line-out, speaker and hp-pins coexist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed compile errors with older gcc for initialization of a union.
sound/pci/ca0106/ca0106_mixer.c: At top level:
sound/pci/ca0106/ca0106_mixer.c:499: unknown field 'p' specified in initializer
sound/pci/ca0106/ca0106_mixer.c:499: warning: missing braces around initializer
sound/pci/ca0106/ca0106_mixer.c:499: warning: (near initialization for 'snd_ca0106_volume_ctls[0].tlv')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Modules: HDA Codec driver,HDA generic driver
- Fix autoconfig speaker/hp detection
Now it allows multiple speaker pins (e.g. Dell laptops have such config)
- Use speaker or hp pins if no line-outs are available
This fixes the silence output on recent Dell laptops with STAC9200
(ALSA bug#1843)
- Fix analog/realtek/sigmatel autoconfig parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Add 'fujitsu' model for ALC262 patch to support a FSC laptop.
The internal speaker is turned on/off with jack sensing.
Also fixed alc262 'basic' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Common labels for input pins
- Fix and clean up of Realtek codec parsers
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
This patch adds the support of ALC262,ALC883,ALC885,ALC861 to driver
More models and improvements for ALC880, ALC260 and ALC882 codecs, too.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Fix connection list parsing (with ranged flag).
- Increase the max number of connections
- Introduce widget capabilities cache
- Power up/down widgets at init, suspend and resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Remove xxx_t typedefs from the HD-Audio codec support codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Fix the auto-assignment of speaker pin. Handle it independently from
line-out pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Add common channel-mode helper functions for all codec patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Make bound controls global to all patches
- Clean up analog patches (for the upcoming extension to AD1988)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Documentation,HDA Codec driver,HDA generic driver,HDA Intel driver
- Fix some invalid configurations, typos in the last patch
- Make init_verbs chainable, so that different configs can share the same
init_verbs
- Reorder and clean up the source codes in patch_realtek.c
- Add the pin default configuration parser, used commonly in cmedia
and realtek patch codes.
- Add 'auto' model to ALC880 for auto-configuration from BIOS
Use this model as default, and 3-stack as fallback
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver,HDA generic driver
Renamed pci_vendor/pci_device fields to pci_subvendor/pci_subdevice.
They are really PCI subsystem IDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
