Age | Commit message (Collapse) | Author |
|
Added the SSID of a known iMac 24" to automatically use
ALC885_IMAC24 quirk.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
I have Toshiba dynabook SS RX1 and this patch adds that support.
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
On some Realtek codecs, the analog PLL gating control bit must be set
off while the default value is 1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These two motherboards's pin configuration are not covered by driver.
I wrote a new model to support them.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed EAPD and COEF setups for Realtek ALC662/663, 660-VD and 888 codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Show more exact codec chip name in the PCM stream name strings.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the support of ALC663 codec, including specific models for
ASUS M51VA, ASUS G71V, ASUS H13 and ASUS G50V.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I think that hda_verb array must have "terminator (empty array)".
But alc262_sony_unsol[] does not have it.
And it causes gcc-4.3's buggy behavior
with snd_hda_sequence_write().
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use quirk table to assign ALC268_TOSHIBA to COMPAL IFL90/JFL-92 laptops.
No analog output on autoprobe.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Guri <gurashka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The auto-config mode of Realtek ALC codecs has a bug since 2.6.25
that it cannot resume properly. The problem was the wrong assignment
of init_hook that overrides the whole initialization.
Relevant bug reports:
http://bugzilla.kernel.org/show_bug.cgi?id=10662
https://bugzilla.novell.com/show_bug.cgi?id=385473
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added IDs for the Foxconn P35AX-S mainboard to patch_realtek.c, so
that ALC883_6ST_DIG is used by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the missing COEF and EAPD initialization in ALC889 auto-configuration
mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Corrected the model assignment for the ASUS P5GD1 w/SPDIF after reports of
surround sound not being possible.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed the speaker auto-mute with two laptop and docking headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Tony Vroon <tony@linx.net>
|
|
alc861_auto_set_output_and_unmute()
Change done by:
commit f6c7e5461e9046445d50c5c7a9a4587824239623
[ALSA] hda-codec - Fix auto-configuration of Realtek codecs
broke sound on ALC861 Analog.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the support of Medion RIM 2150 laptop with ALC880 codec.
ALSA bug#3708:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3708
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Set the proper model=acer for Acer Aspire 5720z with ALC268 codec.
ALSA bug#3550:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3550
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The last ALC889A hack may break on some devices with certain model presets
since patch_alc*() have different model tables. So, now it's handled in
the original patch_alc882() but fly to patch_alc883() in model=auto
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALC889A is recognized ALC885/ALC882 but it's actually closer to
ALC888/ALC883.
Cc: Kasper Sandberg <lkml@metanurb.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds support for Quanta IL1 mini-notebook to alsa, defining a new model
for it. It comes with an ALC267 codec chip. Some notes about this model:
* In headphone automute, I use AC_VERB_SET_PIN_WIDGET_CONTROL instead of common
amp mute, to avoid conflict with mixer switch (mixer and automute use the
same nid).
* The only connected capture sources in the hardware are the internal mic and
external mic jack. So instead of using an input source selector like on other
ALC268 models, the mic automute automatically switch between captures.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The legacy PC speaker signal was not routed to outputs. The codec is not
prevented from powering down in this patch, although I suppose one could
argue that perhaps it should be. Let me know if anyone feels strongly one
way or the other.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To mute the output of Pin widget 15 in ALC880, we should use the
HDA_OUTPUT. However, current code looks like :
snd_hda_codec_amp_stereo(codec, 0x15, HDA_INPUT, 0, HDA_AMP_MUTE, bits);
It may be a misspelling.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Please refer to [0003848] on the alsa mantis.
This patch adds the pci quirk and Mic-Int controller.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for mic automute in clevo-m720r ALC883 model, and rename it
to more generic clevo-m720. Also change model entry in ALSA-Configuration.txt
accordingly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Map clevo-m720r ALC883 model for Clevo M720SR.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Forgot one more: 3stack-hp model also have now the same mixer as
3stack-6ch (after DAC assignment fix in ALC883), so use it avoiding
duplicating the same mixer definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After DAC assignment fix in ALC883, alc888_6st_dell_mixer is now the
same as alc883_base_mixer. Avoid duplicated code and use
alc883_base_mixer in 6stack-dell model, removing alc888_6st_dell_mixer
definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After DAC assignment fix in ALC883, the 6stack-hp model is now the same
as 6stack-dig. So just remove 6stack-hp model and replace its use with
6stack-dig.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This model is to support the Lenovo 3000 y410.
ALSA bug#3856:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3856
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Keep the format verb at closing PCM streams.
Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Map 3stack-6ch-dig ALC883 model for MSI 945GCM5 V2 (MSI-7267).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed the handling of dmics on ALC268 in the auto-configuration mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the device has only one input source, it makes no sense to have
multiple capture streams.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initialize the capture source properly for auto model.
It's especially important for cases that only mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the beep volume control to ALC268 codec support code.
Since the codec doesn't return the correct AMP caps, we need to override
the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed ALC662 recording issue.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use a private array for TLV entries of virtual master controls instead
of (supposed) static array. This cleans up the existing codes.
Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|