Age | Commit message (Collapse) | Author |
|
To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags. This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Factor out the common code of the mixer callbacks that handle controls
that just switch a single GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
The Xonar D2X and DX are very similar to the D2 and D1, respectively, so
we can handle the differences dynamically instead of using a separate
model structure for each one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add suspend/resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Move the setting of the output enable GPIO bit to a separate function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Create separate functions for the code that initializes the hardware, as
opposed to initializing internal driver state, so that they can be
reused for resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
When initializing the DAC volume registers, we can just use the generic
volume update functions instead of setting the registers manually.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Save the written values of all CMI8788 and AC97 registers and of some of
the DAC/ADC registers so that it is possible to restore the register
state later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add a pointer for DAC volume TLV data to the model structure so that the
model driver do not need to manually assign it in their control filter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add fields for the DAC volume limits to the module structure so that
model drivers do not need to install their own control info handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the GPIO 1 mixer control to enable I/O through the front panel
connector of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On the Xonar DX, initialize all bits of the two-wire control register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a mixer control for switching whatever it is that is connected to
GPIO pin 1 on the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the card model does not have a digital input or an AC97 codec,
disable the respective interrupt and mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When selecting the capture source on the Xonar DX, the input jack must
be routed to either the line input or the microphone input by setting a
GPIO pin. This requires an additional callback so that the model driver
can hook into the toggling of AC97 switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the Asus Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix a (fortunately harmless) typo.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change the card short name to show to show the card name instead of the
chip name.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When playing data at 96 kHz or higher, reduce the DAC oversampling rate
to 32.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the code that is common to all Xonar models to a separate function,
and make it more generic in preparation for another model.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rename all CS5381 symbols to CS53x1 because they can also be used for
Xonar models with a CS5361.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use separate model structures for the D2 and D2X so that the init
function does not have to check for the model again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When specifying which PCM devices to use, model drivers now use flags
that also specify the routing between PCM devices and DMA channels
instead of just DMA channel bits. This simplifies some code that checks
for these flags.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the PCM1796 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use priv_idx as an identifier.
sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one
sound/pci/oxygen/virtuoso.c:56:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On the Xonar D2X, monitor the GPIO pin that indicates whether external
power is present.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add mixer controls for the front panel AC97 codec.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Move the line input switching code to the Virtuoso driver because only
the Xonar cards bypass the analog mixer for line input.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add a field to struct oxygen_model to allow model drivers for cards with
less than eight output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add symbol definitions for the various codecs and GPIO pins.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port. Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add more symbols for registers and register fields.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add proper register bit symbols for the I2S format field, and allow card
models to configure the I2S format to be used for the DACs and ADCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Allow the models to modify mixer controls before they are added to the
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Allow the card models to specify whether each of the hardware DMA
channels is used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Do not exchange the surround and back jacks except when in 7.1 mode
where the surround jack is not rear but side.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add the snd-virtuoso driver for the Asus Virtuoso 200 chip used on the
PCI and PCI-E models of the Xonar sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|