From aee1dc73b519227084d77b0b2fc972b68b4153d8 Mon Sep 17 00:00:00 2001 From: Jason Jin Date: Fri, 23 May 2008 16:32:45 +0800 Subject: [POWERPC] Update booting-without-of for Freescale PCIe MSI Binding document adding for Freescale PCIe MSI support. Signed-off-by: Jason Jin Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 43 +++++++++++++++++++++++++++- 1 file changed, 42 insertions(+), 1 deletion(-) (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 1d2a772506c..c67d2f58975 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -57,7 +57,10 @@ Table of Contents n) 4xx/Axon EMAC ethernet nodes o) Xilinx IP cores p) Freescale Synchronous Serial Interface - q) USB EHCI controllers + q) USB EHCI controllers + r) Freescale Display Interface Unit + s) Freescale on board FPGA + t) Freescael MSI interrupt controller VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -2870,6 +2873,44 @@ platforms are moved over to use the flattened-device-tree model. reg = <0xe8000000 32>; }; + t) Freescale MSI interrupt controller + + Reguired properities: + - compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. + - reg : should contain the address and the length of the shared message + interrupt register set. + - msi-available-ranges: use style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. + - interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. + - interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + + Example + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; + + VII - Marvell Discovery mv64[345]6x System Controller chips =========================================================== -- cgit v1.2.3 From acd4b715ec83e451990bb82bdbf28ecaeab1b67d Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Fri, 30 May 2008 12:12:26 -0500 Subject: [POWERPC] Cleanup mpic nodes in .dts Removed clock-frequency, big-endian, and built-in props as they aren't specified anywhere. Also added compatible = "chrp,open-pic" in the places it was missing. Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 6 ------ 1 file changed, 6 deletions(-) (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index c67d2f58975..948f6417a40 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1363,14 +1363,11 @@ platforms are moved over to use the flattened-device-tree model. pic@40000 { linux,phandle = <40000>; - clock-frequency = <0>; interrupt-controller; #address-cells = <0>; reg = <40000 40000>; - built-in; compatible = "chrp,open-pic"; device_type = "open-pic"; - big-endian; }; @@ -3663,14 +3660,11 @@ not necessary as they are usually the same as the root node. pic@40000 { linux,phandle = <40000>; - clock-frequency = <0>; interrupt-controller; #address-cells = <0>; reg = <40000 40000>; - built-in; compatible = "chrp,open-pic"; device_type = "open-pic"; - big-endian; }; i2c@3000 { -- cgit v1.2.3 From 83ff9dcf375c418ca3b98eb950711525ca1269e2 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Fri, 23 May 2008 20:38:54 +0400 Subject: powerpc/sysdev: implement FSL GTM support GTM stands for General-purpose Timers Module and able to generate timer{1,2,3,4} interrupts. These timers are used by the drivers that need time precise interrupts (like for USB transactions scheduling for the Freescale USB Host controller as found in some QE and CPM chips), or these timers could be used as wakeup events from the CPU deep-sleep mode. Things unimplemented: 1. Cascaded (32 bit) timers (1-2, 3-4). This is straightforward to implement when needed, two timers should be marked as "requested" and configured as appropriate. 2. Super-cascaded (64 bit) timers (1-2-3-4). This is also straightforward to implement when needed, all timers should be marked as "requested" and configured as appropriate. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 32 ++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 948f6417a40..8675ebca2cf 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -61,6 +61,7 @@ Table of Contents r) Freescale Display Interface Unit s) Freescale on board FPGA t) Freescael MSI interrupt controller + u) Freescale General-purpose Timers Module VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -2907,6 +2908,37 @@ platforms are moved over to use the flattened-device-tree model. interrupt-parent = <&mpic>; }; + u) Freescale General-purpose Timers Module + + Required properties: + - compatible : should be + "fsl,-gtm", "fsl,gtm" for SOC GTMs + "fsl,-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + + Example: + + timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; + }; + + timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; + }; VII - Marvell Discovery mv64[345]6x System Controller chips =========================================================== -- cgit v1.2.3 From 32def337aafee0bc65eb58d5b1b3617525eb7fb7 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Mon, 19 May 2008 21:47:05 +0400 Subject: powerpc/QE: implement support for the GPIO LIB API This is needed to access QE GPIOs via Linux GPIO API. Signed-off-by: Anton Vorontsov Acked-By: Timur Tabi Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+) (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 8675ebca2cf..b68684d39f9 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1736,6 +1736,33 @@ platforms are moved over to use the flattened-device-tree model. ...... }; + Note that "par_io" nodes are obsolete, and should not be used for + the new device trees. Instead, each Par I/O bank should be represented + via its own gpio-controller node: + + Required properties: + - #gpio-cells : should be "2". + - compatible : should be "fsl,-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". + - reg : offset to the register set and its length. + - gpio-controller : node to identify gpio controllers. + + Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; vi) Pin configuration nodes -- cgit v1.2.3 From 70bf0333d72cd66daf7664c44708f65518b267cc Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Wed, 25 Jun 2008 13:14:36 -0700 Subject: powerpc/bootwrapper: Add documentation of boot wrapper targets There have been many questions on and off the mailing list about how exactly the bootwrapper is used for embedded targets. Add some documentation and help text to try and clarify the system. Signed-off-by: Grant Likely --- Documentation/powerpc/bootwrapper.txt | 141 ++++++++++++++++++++++++++++++++++ 1 file changed, 141 insertions(+) create mode 100644 Documentation/powerpc/bootwrapper.txt (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/bootwrapper.txt b/Documentation/powerpc/bootwrapper.txt new file mode 100644 index 00000000000..d60fced5e1c --- /dev/null +++ b/Documentation/powerpc/bootwrapper.txt @@ -0,0 +1,141 @@ +The PowerPC boot wrapper +------------------------ +Copyright (C) Secret Lab Technologies Ltd. + +PowerPC image targets compresses and wraps the kernel image (vmlinux) with +a boot wrapper to make it usable by the system firmware. There is no +standard PowerPC firmware interface, so the boot wrapper is designed to +be adaptable for each kind of image that needs to be built. + +The boot wrapper can be found in the arch/powerpc/boot/ directory. The +Makefile in that directory has targets for all the available image types. +The different image types are used to support all of the various firmware +interfaces found on PowerPC platforms. OpenFirmware is the most commonly +used firmware type on general purpose PowerPC systems from Apple, IBM and +others. U-Boot is typically found on embedded PowerPC hardware, but there +are a handful of other firmware implementations which are also popular. Each +firmware interface requires a different image format. + +The boot wrapper is built from the makefile in arch/powerpc/boot/Makefile and +it uses the wrapper script (arch/powerpc/boot/wrapper) to generate target +image. The details of the build system is discussed in the next section. +Currently, the following image format targets exist: + + cuImage.%: Backwards compatible uImage for older version of + U-Boot (for versions that don't understand the device + tree). This image embeds a device tree blob inside + the image. The boot wrapper, kernel and device tree + are all embedded inside the U-Boot uImage file format + with boot wrapper code that extracts data from the old + bd_info structure and loads the data into the device + tree before jumping into the kernel. + Because of the series of #ifdefs found in the + bd_info structure used in the old U-Boot interfaces, + cuImages are platform specific. Each specific + U-Boot platform has a different platform init file + which populates the embedded device tree with data + from the platform specific bd_info file. The platform + specific cuImage platform init code can be found in + arch/powerpc/boot/cuboot.*.c. Selection of the correct + cuImage init code for a specific board can be found in + the wrapper structure. + dtbImage.%: Similar to zImage, except device tree blob is embedded + inside the image instead of provided by firmware. The + output image file can be either an elf file or a flat + binary depending on the platform. + dtbImages are used on systems which do not have an + interface for passing a device tree directly. + dtbImages are similar to simpleImages except that + dtbImages have platform specific code for extracting + data from the board firmware, but simpleImages do not + talk to the firmware at all. + PlayStation 3 support uses dtbImage. So do Embedded + Planet boards using the PlanetCore firmware. Board + specific initialization code is typically found in a + file named arch/powerpc/boot/.c; but this + can be overridden by the wrapper script. + simpleImage.%: Firmware independent compressed image that does not + depend on any particular firmware interface and embeds + a device tree blob. This image is a flat binary that + can be loaded to any location in RAM and jumped to. + Firmware cannot pass any configuration data to the + kernel with this image type and it depends entirely on + the embedded device tree for all information. + The simpleImage is useful for booting systems with + an unknown firmware interface or for booting from + a debugger when no firmware is present (such as on + the Xilinx Virtex platform). The only assumption that + simpleImage makes is that RAM is correctly initialized + and that the MMU is either off or has RAM mapped to + base address 0. + simpleImage also supports inserting special platform + specific initialization code to the start of the bootup + sequence. The virtex405 platform uses this feature to + ensure that the cache is invalidated before caching + is enabled. Platform specific initialization code is + added as part of the wrapper script and is keyed on + the image target name. For example, all + simpleImage.virtex405-* targets will add the + virtex405-head.S initialization code (This also means + that the dts file for virtex405 targets should be + named (virtex405-.dts). Search the wrapper + script for 'virtex405' and see the file + arch/powerpc/boot/virtex405-head.S for details. + treeImage.%; Image format for used with OpenBIOS firmware found + on some ppc4xx hardware. This image embeds a device + tree blob inside the image. + uImage: Native image format used by U-Boot. The uImage target + does not add any boot code. It just wraps a compressed + vmlinux in the uImage data structure. This image + requires a version of U-Boot that is able to pass + a device tree to the kernel at boot. If using an older + version of U-Boot, then you need to use a cuImage + instead. + zImage.%: Image format which does not embed a device tree. + Used by OpenFirmware and other firmware interfaces + which are able to supply a device tree. This image + expects firmware to provide the device tree at boot. + Typically, if you have general purpose PowerPC + hardware then you want this image format. + +Image types which embed a device tree blob (simpleImage, dtbImage, treeImage, +and cuImage) all generate the device tree blob from a file in the +arch/powerpc/boot/dts/ directory. The Makefile selects the correct device +tree source based on the name of the target. Therefore, if the kernel is +built with 'make treeImage.walnut simpleImage.virtex405-ml403', then the +build system will use arch/powerpc/boot/dts/walnut.dts to build +treeImage.walnut and arch/powerpc/boot/dts/virtex405-ml403.dts to build +the simpleImage.virtex405-ml403. + +Two special targets called 'zImage' and 'zImage.initrd' also exist. These +targets build all the default images as selected by the kernel configuration. +Default images are selected by the boot wrapper Makefile +(arch/powerpc/boot/Makefile) by adding targets to the $image-y variable. Look +at the Makefile to see which default image targets are available. + +How it is built +--------------- +arch/powerpc is designed to support multiplatform kernels, which means +that a single vmlinux image can be booted on many different target boards. +It also means that the boot wrapper must be able to wrap for many kinds of +images on a single build. The design decision was made to not use any +conditional compilation code (#ifdef, etc) in the boot wrapper source code. +All of the boot wrapper pieces are buildable at any time regardless of the +kernel configuration. Building all the wrapper bits on every kernel build +also ensures that obscure parts of the wrapper are at the very least compile +tested in a large variety of environments. + +The wrapper is adapted for different image types at link time by linking in +just the wrapper bits that are appropriate for the image type. The 'wrapper +script' (found in arch/powerpc/boot/wrapper) is called by the Makefile and +is responsible for selecting the correct wrapper bits for the image type. +The arguments are well documented in the script's comment block, so they +are not repeated here. However, it is worth mentioning that the script +uses the -p (platform) argument as the main method of deciding which wrapper +bits to compile in. Look for the large 'case "$platform" in' block in the +middle of the script. This is also the place where platform specific fixups +can be selected by changing the link order. + +In particular, care should be taken when working with cuImages. cuImage +wrapper bits are very board specific and care should be taken to make sure +the target you are trying to build is supported by the wrapper bits. -- cgit v1.2.3 From a5d28c8e64ff0bc77d38d9c19c6d8163e4c0ffaa Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Wed, 2 Jul 2008 18:06:13 +0200 Subject: powerpc/CPM: Add i2c pins to dts and board setup Initialize I2C pins on boards with CPM1/CPM2 controllers and document the i2c bus in booting-without-of. The boards don't have any I2C chips connected to the I2C bus, so unless some external chips are connected to the boards, this code is just an example of setting everything else up. Signed-off-by: Jochen Friedrich Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 42 ++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index b68684d39f9..f6394b50943 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -2160,6 +2160,48 @@ platforms are moved over to use the flattened-device-tree model. }; }; + x) I2C + + The I2C controller is expressed as a bus under the CPM node. + + Properties: + - compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" + - reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). + - #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. + - #size-cells : Should be zero. + - clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. + The following two properties are deprecated. They are only used by legacy + i2c drivers to find the bus to probe: + - linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. + - linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + + Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; + m) Chipselect/Local Bus Properties: -- cgit v1.2.3 From d0fc2eaaf4c56a95f5ed29b6bfb609e19714fc16 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Mon, 7 Jul 2008 11:28:33 -0500 Subject: powerpc/fsl: Refactor device bindings Moved Freescale SoC related bindings out of booting-without-of.txt and into their own files. Signed-off-by: Kumar Gala --- Documentation/powerpc/booting-without-of.txt | 1218 +------------------- Documentation/powerpc/dts-bindings/fsl/board.txt | 29 + .../powerpc/dts-bindings/fsl/cpm_qe/cpm.txt | 67 ++ .../powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt | 21 + .../powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt | 41 + .../powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt | 18 + .../powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt | 15 + .../powerpc/dts-bindings/fsl/cpm_qe/network.txt | 45 + .../powerpc/dts-bindings/fsl/cpm_qe/qe.txt | 58 + .../dts-bindings/fsl/cpm_qe/qe/firmware.txt | 24 + .../powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt | 51 + .../powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt | 60 + .../powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt | 70 ++ .../powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt | 22 + .../powerpc/dts-bindings/fsl/cpm_qe/serial.txt | 21 + Documentation/powerpc/dts-bindings/fsl/diu.txt | 18 + Documentation/powerpc/dts-bindings/fsl/dma.txt | 127 ++ Documentation/powerpc/dts-bindings/fsl/gtm.txt | 31 + Documentation/powerpc/dts-bindings/fsl/guts.txt | 25 + Documentation/powerpc/dts-bindings/fsl/i2c.txt | 32 + Documentation/powerpc/dts-bindings/fsl/lbc.txt | 35 + Documentation/powerpc/dts-bindings/fsl/msi-pic.txt | 36 + Documentation/powerpc/dts-bindings/fsl/sata.txt | 29 + Documentation/powerpc/dts-bindings/fsl/spi.txt | 24 + Documentation/powerpc/dts-bindings/fsl/ssi.txt | 38 + Documentation/powerpc/dts-bindings/fsl/tsec.txt | 69 ++ Documentation/powerpc/dts-bindings/fsl/usb.txt | 59 + 27 files changed, 1077 insertions(+), 1206 deletions(-) create mode 100644 Documentation/powerpc/dts-bindings/fsl/board.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/diu.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/dma.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/gtm.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/guts.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/i2c.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/lbc.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/msi-pic.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/sata.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/spi.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/ssi.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/tsec.txt create mode 100644 Documentation/powerpc/dts-bindings/fsl/usb.txt (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index f6394b50943..de2e5c05d6e 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -41,27 +41,12 @@ Table of Contents VI - System-on-a-chip devices and nodes 1) Defining child nodes of an SOC 2) Representing devices without a current OF specification - a) MDIO IO device - b) Gianfar-compatible ethernet nodes - c) PHY nodes - d) Interrupt controllers - e) I2C - f) Freescale SOC USB controllers - g) Freescale SOC SEC Security Engines - h) Board Control and Status (BCSR) - i) Freescale QUICC Engine module (QE) - j) CFI or JEDEC memory-mapped NOR flash - k) Global Utilities Block - l) Freescale Communications Processor Module - m) Chipselect/Local Bus - n) 4xx/Axon EMAC ethernet nodes - o) Xilinx IP cores - p) Freescale Synchronous Serial Interface - q) USB EHCI controllers - r) Freescale Display Interface Unit - s) Freescale on board FPGA - t) Freescael MSI interrupt controller - u) Freescale General-purpose Timers Module + a) PHY nodes + b) Interrupt controllers + c) CFI or JEDEC memory-mapped NOR flash + d) 4xx/Axon EMAC ethernet nodes + e) Xilinx IP cores + f) USB EHCI controllers VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -1250,80 +1235,7 @@ descriptions for the SOC devices for which new nodes have been defined; this list will expand as more and more SOC-containing platforms are moved over to use the flattened-device-tree model. - a) MDIO IO device - - The MDIO is a bus to which the PHY devices are connected. For each - device that exists on this bus, a child node should be created. See - the definition of the PHY node below for an example of how to define - a PHY. - - Required properties: - - reg : Offset and length of the register set for the device - - compatible : Should define the compatible device type for the - mdio. Currently, this is most likely to be "fsl,gianfar-mdio" - - Example: - - mdio@24520 { - reg = <24520 20>; - compatible = "fsl,gianfar-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - - - b) Gianfar-compatible ethernet nodes - - Required properties: - - - device_type : Should be "network" - - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" - - compatible : Should be "gianfar" - - reg : Offset and length of the register set for the device - - mac-address : List of bytes representing the ethernet address of - this controller - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - phy-handle : The phandle for the PHY connected to this ethernet - controller. - - fixed-link : where a is emulated phy id - choose any, - but unique to the all specified fixed-links, b is duplex - 0 half, - 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no - pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. - - Recommended properties: - - - phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", - "tbi", or "rtbi". This property is only really needed if the connection - is of type "rgmii-id", as all other connection types are detected by - hardware. - - - Example: - - ethernet@24000 { - #size-cells = <0>; - device_type = "network"; - model = "TSEC"; - compatible = "gianfar"; - reg = <24000 1000>; - mac-address = [ 00 E0 0C 00 73 00 ]; - interrupts = ; - interrupt-parent = <40000>; - phy-handle = <2452000> - }; - - - - c) PHY nodes + a) PHY nodes Required properties: @@ -1351,7 +1263,7 @@ platforms are moved over to use the flattened-device-tree model. }; - d) Interrupt controllers + b) Interrupt controllers Some SOC devices contain interrupt controllers that are different from the standard Open PIC specification. The SOC device nodes for @@ -1371,508 +1283,7 @@ platforms are moved over to use the flattened-device-tree model. device_type = "open-pic"; }; - - e) I2C - - Required properties : - - - device_type : Should be "i2c" - - reg : Offset and length of the register set for the device - - Recommended properties : - - - compatible : Should be "fsl-i2c" for parts compatible with - Freescale I2C specifications. - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - dfsrr : boolean; if defined, indicates that this I2C device has - a digital filter sampling rate register - - fsl5200-clocking : boolean; if defined, indicated that this device - uses the FSL 5200 clocking mechanism. - - Example : - - i2c@3000 { - interrupt-parent = <40000>; - interrupts = <1b 3>; - reg = <3000 18>; - device_type = "i2c"; - compatible = "fsl-i2c"; - dfsrr; - }; - - - f) Freescale SOC USB controllers - - The device node for a USB controller that is part of a Freescale - SOC is as described in the document "Open Firmware Recommended - Practice : Universal Serial Bus" with the following modifications - and additions : - - Required properties : - - compatible : Should be "fsl-usb2-mph" for multi port host USB - controllers, or "fsl-usb2-dr" for dual role USB controllers - - phy_type : For multi port host USB controllers, should be one of - "ulpi", or "serial". For dual role USB controllers, should be - one of "ulpi", "utmi", "utmi_wide", or "serial". - - reg : Offset and length of the register set for the device - - port0 : boolean; if defined, indicates port0 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port1" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - port1 : boolean; if defined, indicates port1 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port0" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible - controllers. Can be "host", "peripheral", or "otg". Default to - "host" if not defined for backward compatibility. - - Recommended properties : - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - Example multi port host USB controller device node : - usb@22000 { - compatible = "fsl-usb2-mph"; - reg = <22000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <27 1>; - phy_type = "ulpi"; - port0; - port1; - }; - - Example dual role USB controller device node : - usb@23000 { - compatible = "fsl-usb2-dr"; - reg = <23000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <26 1>; - dr_mode = "otg"; - phy = "ulpi"; - }; - - - g) Freescale SOC SEC Security Engines - - Required properties: - - - device_type : Should be "crypto" - - model : Model of the device. Should be "SEC1" or "SEC2" - - compatible : Should be "talitos" - - reg : Offset and length of the register set for the device - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - num-channels : An integer representing the number of channels - available. - - channel-fifo-len : An integer representing the number of - descriptor pointers each channel fetch fifo can hold. - - exec-units-mask : The bitmask representing what execution units - (EUs) are available. It's a single 32-bit cell. EU information - should be encoded following the SEC's Descriptor Header Dword - EU_SEL0 field documentation, i.e. as follows: - - bit 0 = reserved - should be 0 - bit 1 = set if SEC has the ARC4 EU (AFEU) - bit 2 = set if SEC has the DES/3DES EU (DEU) - bit 3 = set if SEC has the message digest EU (MDEU) - bit 4 = set if SEC has the random number generator EU (RNG) - bit 5 = set if SEC has the public key EU (PKEU) - bit 6 = set if SEC has the AES EU (AESU) - bit 7 = set if SEC has the Kasumi EU (KEU) - - bits 8 through 31 are reserved for future SEC EUs. - - - descriptor-types-mask : The bitmask representing what descriptors - are available. It's a single 32-bit cell. Descriptor type - information should be encoded following the SEC's Descriptor - Header Dword DESC_TYPE field documentation, i.e. as follows: - - bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type - bit 1 = set if SEC supports the ipsec_esp descriptor type - bit 2 = set if SEC supports the common_nonsnoop desc. type - bit 3 = set if SEC supports the 802.11i AES ccmp desc. type - bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type - bit 5 = set if SEC supports the srtp descriptor type - bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type - bit 7 = set if SEC supports the pkeu_assemble descriptor type - bit 8 = set if SEC supports the aesu_key_expand_output desc.type - bit 9 = set if SEC supports the pkeu_ptmul descriptor type - bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type - bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type - - ..and so on and so forth. - - Example: - - /* MPC8548E */ - crypto@30000 { - device_type = "crypto"; - model = "SEC2"; - compatible = "talitos"; - reg = <30000 10000>; - interrupts = <1d 3>; - interrupt-parent = <40000>; - num-channels = <4>; - channel-fifo-len = <18>; - exec-units-mask = <000000fe>; - descriptor-types-mask = <012b0ebf>; - }; - - h) Board Control and Status (BCSR) - - Required properties: - - - device_type : Should be "board-control" - - reg : Offset and length of the register set for the device - - Example: - - bcsr@f8000000 { - device_type = "board-control"; - reg = ; - }; - - i) Freescale QUICC Engine module (QE) - This represents qe module that is installed on PowerQUICC II Pro. - - NOTE: This is an interim binding; it should be updated to fit - in with the CPM binding later in this document. - - Basically, it is a bus of devices, that could act more or less - as a complete entity (UCC, USB etc ). All of them should be siblings on - the "root" qe node, using the common properties from there. - The description below applies to the qe of MPC8360 and - more nodes and properties would be extended in the future. - - i) Root QE device - - Required properties: - - compatible : should be "fsl,qe"; - - model : precise model of the QE, Can be "QE", "CPM", or "CPM2" - - reg : offset and length of the device registers. - - bus-frequency : the clock frequency for QUICC Engine. - - Recommended properties - - brg-frequency : the internal clock source frequency for baud-rate - generators in Hz. - - Example: - qe@e0100000 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,qe"; - ranges = <0 e0100000 00100000>; - reg = ; - brg-frequency = <0>; - bus-frequency = <179A7B00>; - } - - - ii) SPI (Serial Peripheral Interface) - - Required properties: - - cell-index : SPI controller index. - - compatible : should be "fsl,spi". - - mode : the SPI operation mode, it can be "cpu" or "cpu-qe". - - reg : Offset and length of the register set for the device - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - Example: - spi@4c0 { - cell-index = <0>; - compatible = "fsl,spi"; - reg = <4c0 40>; - interrupts = <82 0>; - interrupt-parent = <700>; - mode = "cpu"; - }; - - - iii) USB (Universal Serial Bus Controller) - - Required properties: - - compatible : could be "qe_udc" or "fhci-hcd". - - mode : the could be "host" or "slave". - - reg : Offset and length of the register set for the device - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - Example(slave): - usb@6c0 { - compatible = "qe_udc"; - reg = <6c0 40>; - interrupts = <8b 0>; - interrupt-parent = <700>; - mode = "slave"; - }; - - - iv) UCC (Unified Communications Controllers) - - Required properties: - - device_type : should be "network", "hldc", "uart", "transparent" - "bisync", "atm", or "serial". - - compatible : could be "ucc_geth" or "fsl_atm" and so on. - - cell-index : the ucc number(1-8), corresponding to UCCx in UM. - - reg : Offset and length of the register set for the device - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - pio-handle : The phandle for the Parallel I/O port configuration. - - port-number : for UART drivers, the port number to use, between 0 and 3. - This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. - The port number is added to the minor number of the device. Unlike the - CPM UART driver, the port-number is required for the QE UART driver. - - soft-uart : for UART drivers, if specified this means the QE UART device - driver should use "Soft-UART" mode, which is needed on some SOCs that have - broken UART hardware. Soft-UART is provided via a microcode upload. - - rx-clock-name: the UCC receive clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively - - tx-clock-name: the UCC transmit clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively - The following two properties are deprecated. rx-clock has been replaced - with rx-clock-name, and tx-clock has been replaced with tx-clock-name. - Drivers that currently use the deprecated properties should continue to - do so, in order to support older device trees, but they should be updated - to check for the new properties first. - - rx-clock : represents the UCC receive clock source. - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. - - tx-clock: represents the UCC transmit clock source; - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. - - Required properties for network device_type: - - mac-address : list of bytes representing the ethernet address. - - phy-handle : The phandle for the PHY connected to this controller. - - Recommended properties: - - phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal - Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), - "tbi", or "rtbi". - - Example: - ucc@2000 { - device_type = "network"; - compatible = "ucc_geth"; - cell-index = <1>; - reg = <2000 200>; - interrupts = ; - interrupt-parent = <700>; - mac-address = [ 00 04 9f 00 23 23 ]; - rx-clock = "none"; - tx-clock = "clk9"; - phy-handle = <212000>; - phy-connection-type = "gmii"; - pio-handle = <140001>; - }; - - - v) Parallel I/O Ports - - This node configures Parallel I/O ports for CPUs with QE support. - The node should reside in the "soc" node of the tree. For each - device that using parallel I/O ports, a child node should be created. - See the definition of the Pin configuration nodes below for more - information. - - Required properties: - - device_type : should be "par_io". - - reg : offset to the register set and its length. - - num-ports : number of Parallel I/O ports - - Example: - par_io@1400 { - reg = <1400 100>; - #address-cells = <1>; - #size-cells = <0>; - device_type = "par_io"; - num-ports = <7>; - ucc_pin@01 { - ...... - }; - - Note that "par_io" nodes are obsolete, and should not be used for - the new device trees. Instead, each Par I/O bank should be represented - via its own gpio-controller node: - - Required properties: - - #gpio-cells : should be "2". - - compatible : should be "fsl,-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank". - - reg : offset to the register set and its length. - - gpio-controller : node to identify gpio controllers. - - Example: - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; - - vi) Pin configuration nodes - - Required properties: - - linux,phandle : phandle of this node; likely referenced by a QE - device. - - pio-map : array of pin configurations. Each pin is defined by 6 - integers. The six numbers are respectively: port, pin, dir, - open_drain, assignment, has_irq. - - port : port number of the pin; 0-6 represent port A-G in UM. - - pin : pin number in the port. - - dir : direction of the pin, should encode as follows: - - 0 = The pin is disabled - 1 = The pin is an output - 2 = The pin is an input - 3 = The pin is I/O - - - open_drain : indicates the pin is normal or wired-OR: - - 0 = The pin is actively driven as an output - 1 = The pin is an open-drain driver. As an output, the pin is - driven active-low, otherwise it is three-stated. - - - assignment : function number of the pin according to the Pin Assignment - tables in User Manual. Each pin can have up to 4 possible functions in - QE and two options for CPM. - - has_irq : indicates if the pin is used as source of external - interrupts. - - Example: - ucc_pin@01 { - linux,phandle = <140001>; - pio-map = < - /* port pin dir open_drain assignment has_irq */ - 0 3 1 0 1 0 /* TxD0 */ - 0 4 1 0 1 0 /* TxD1 */ - 0 5 1 0 1 0 /* TxD2 */ - 0 6 1 0 1 0 /* TxD3 */ - 1 6 1 0 3 0 /* TxD4 */ - 1 7 1 0 1 0 /* TxD5 */ - 1 9 1 0 2 0 /* TxD6 */ - 1 a 1 0 2 0 /* TxD7 */ - 0 9 2 0 1 0 /* RxD0 */ - 0 a 2 0 1 0 /* RxD1 */ - 0 b 2 0 1 0 /* RxD2 */ - 0 c 2 0 1 0 /* RxD3 */ - 0 d 2 0 1 0 /* RxD4 */ - 1 1 2 0 2 0 /* RxD5 */ - 1 0 2 0 2 0 /* RxD6 */ - 1 4 2 0 2 0 /* RxD7 */ - 0 7 1 0 1 0 /* TX_EN */ - 0 8 1 0 1 0 /* TX_ER */ - 0 f 2 0 1 0 /* RX_DV */ - 0 10 2 0 1 0 /* RX_ER */ - 0 0 2 0 1 0 /* RX_CLK */ - 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ - 2 8 2 0 1 0>; /* GTX125 - CLK9 */ - }; - - vii) Multi-User RAM (MURAM) - - Required properties: - - compatible : should be "fsl,qe-muram", "fsl,cpm-muram". - - mode : the could be "host" or "slave". - - ranges : Should be defined as specified in 1) to describe the - translation of MURAM addresses. - - data-only : sub-node which defines the address area under MURAM - bus that can be allocated as data/parameter - - Example: - - muram@10000 { - compatible = "fsl,qe-muram", "fsl,cpm-muram"; - ranges = <0 00010000 0000c000>; - - data-only@0{ - compatible = "fsl,qe-muram-data", - "fsl,cpm-muram-data"; - reg = <0 c000>; - }; - }; - - viii) Uploaded QE firmware - - If a new firwmare has been uploaded to the QE (usually by the - boot loader), then a 'firmware' child node should be added to the QE - node. This node provides information on the uploaded firmware that - device drivers may need. - - Required properties: - - id: The string name of the firmware. This is taken from the 'id' - member of the qe_firmware structure of the uploaded firmware. - Device drivers can search this string to determine if the - firmware they want is already present. - - extended-modes: The Extended Modes bitfield, taken from the - firmware binary. It is a 64-bit number represented - as an array of two 32-bit numbers. - - virtual-traps: The virtual traps, taken from the firmware binary. - It is an array of 8 32-bit numbers. - - Example: - - firmware { - id = "Soft-UART"; - extended-modes = <0 0>; - virtual-traps = <0 0 0 0 0 0 0 0>; - } - - j) CFI or JEDEC memory-mapped NOR flash + c) CFI or JEDEC memory-mapped NOR flash Flash chips (Memory Technology Devices) are often used for solid state file systems on embedded devices. @@ -1936,310 +1347,7 @@ platforms are moved over to use the flattened-device-tree model. }; }; - k) Global Utilities Block - - The global utilities block controls power management, I/O device - enabling, power-on-reset configuration monitoring, general-purpose - I/O signal configuration, alternate function selection for multiplexed - signals, and clock control. - - Required properties: - - - compatible : Should define the compatible device type for - global-utilities. - - reg : Offset and length of the register set for the device. - - Recommended properties: - - - fsl,has-rstcr : Indicates that the global utilities register set - contains a functioning "reset control register" (i.e. the board - is wired to reset upon setting the HRESET_REQ bit in this register). - - Example: - - global-utilities@e0000 { /* global utilities block */ - compatible = "fsl,mpc8548-guts"; - reg = ; - fsl,has-rstcr; - }; - - l) Freescale Communications Processor Module - - NOTE: This is an interim binding, and will likely change slightly, - as more devices are supported. The QE bindings especially are - incomplete. - - i) Root CPM node - - Properties: - - compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". - - reg : A 48-byte region beginning with CPCR. - - Example: - cpm@119c0 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; - reg = <119c0 30>; - } - - ii) Properties common to mulitple CPM/QE devices - - - fsl,cpm-command : This value is ORed with the opcode and command flag - to specify the device on which a CPM command operates. - - - fsl,cpm-brg : Indicates which baud rate generator the device - is associated with. If absent, an unused BRG - should be dynamically allocated. If zero, the - device uses an external clock rather than a BRG. - - - reg : Unless otherwise specified, the first resource represents the - scc/fcc/ucc registers, and the second represents the device's - parameter RAM region (if it has one). - - iii) Serial - - Currently defined compatibles: - - fsl,cpm1-smc-uart - - fsl,cpm2-smc-uart - - fsl,cpm1-scc-uart - - fsl,cpm2-scc-uart - - fsl,qe-uart - - Example: - - serial@11a00 { - device_type = "serial"; - compatible = "fsl,mpc8272-scc-uart", - "fsl,cpm2-scc-uart"; - reg = <11a00 20 8000 100>; - interrupts = <28 8>; - interrupt-parent = <&PIC>; - fsl,cpm-brg = <1>; - fsl,cpm-command = <00800000>; - }; - - iii) Network - - Currently defined compatibles: - - fsl,cpm1-scc-enet - - fsl,cpm2-scc-enet - - fsl,cpm1-fec-enet - - fsl,cpm2-fcc-enet (third resource is GFEMR) - - fsl,qe-enet - - Example: - - ethernet@11300 { - device_type = "network"; - compatible = "fsl,mpc8272-fcc-enet", - "fsl,cpm2-fcc-enet"; - reg = <11300 20 8400 100 11390 1>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <20 8>; - interrupt-parent = <&PIC>; - phy-handle = <&PHY0>; - fsl,cpm-command = <12000300>; - }; - - iv) MDIO - - Currently defined compatibles: - fsl,pq1-fec-mdio (reg is same as first resource of FEC device) - fsl,cpm2-mdio-bitbang (reg is port C registers) - - Properties for fsl,cpm2-mdio-bitbang: - fsl,mdio-pin : pin of port C controlling mdio data - fsl,mdc-pin : pin of port C controlling mdio clock - - Example: - - mdio@10d40 { - device_type = "mdio"; - compatible = "fsl,mpc8272ads-mdio-bitbang", - "fsl,mpc8272-mdio-bitbang", - "fsl,cpm2-mdio-bitbang"; - reg = <10d40 14>; - #address-cells = <1>; - #size-cells = <0>; - fsl,mdio-pin = <12>; - fsl,mdc-pin = <13>; - }; - - v) Baud Rate Generators - - Currently defined compatibles: - fsl,cpm-brg - fsl,cpm1-brg - fsl,cpm2-brg - - Properties: - - reg : There may be an arbitrary number of reg resources; BRG - numbers are assigned to these in order. - - clock-frequency : Specifies the base frequency driving - the BRG. - - Example: - - brg@119f0 { - compatible = "fsl,mpc8272-brg", - "fsl,cpm2-brg", - "fsl,cpm-brg"; - reg = <119f0 10 115f0 10>; - clock-frequency = ; - }; - - vi) Interrupt Controllers - - Currently defined compatibles: - - fsl,cpm1-pic - - only one interrupt cell - - fsl,pq1-pic - - fsl,cpm2-pic - - second interrupt cell is level/sense: - - 2 is falling edge - - 8 is active low - - Example: - - interrupt-controller@10c00 { - #interrupt-cells = <2>; - interrupt-controller; - reg = <10c00 80>; - compatible = "mpc8272-pic", "fsl,cpm2-pic"; - }; - - vii) USB (Universal Serial Bus Controller) - - Properties: - - compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" - - Example: - usb@11bc0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,cpm2-usb"; - reg = <11b60 18 8b00 100>; - interrupts = ; - interrupt-parent = <&PIC>; - fsl,cpm-command = <2e600000>; - }; - - viii) Multi-User RAM (MURAM) - - The multi-user/dual-ported RAM is expressed as a bus under the CPM node. - - Ranges must be set up subject to the following restrictions: - - - Children's reg nodes must be offsets from the start of all muram, even - if the user-data area does not begin at zero. - - If multiple range entries are used, the difference between the parent - address and the child address must be the same in all, so that a single - mapping can cover them all while maintaining the ability to determine - CPM-side offsets with pointer subtraction. It is recommended that - multiple range entries not be used. - - A child address of zero must be translatable, even if no reg resources - contain it. - - A child "data" node must exist, compatible with "fsl,cpm-muram-data", to - indicate the portion of muram that is usable by the OS for arbitrary - purposes. The data node may have an arbitrary number of reg resources, - all of which contribute to the allocatable muram pool. - - Example, based on mpc8272: - - muram@0 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 10000>; - - data@0 { - compatible = "fsl,cpm-muram-data"; - reg = <0 2000 9800 800>; - }; - }; - - x) I2C - - The I2C controller is expressed as a bus under the CPM node. - - Properties: - - compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" - - reg : On CPM2 devices, the second resource doesn't specify the I2C - Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM - (typically 0x8afc 0x2). - - #address-cells : Should be one. The cell is the i2c device address with - the r/w bit set to zero. - - #size-cells : Should be zero. - - clock-frequency : Can be used to set the i2c clock frequency. If - unspecified, a default frequency of 60kHz is being used. - The following two properties are deprecated. They are only used by legacy - i2c drivers to find the bus to probe: - - linux,i2c-index : Can be used to hard code an i2c bus number. By default, - the bus number is dynamically assigned by the i2c core. - - linux,i2c-class : Can be used to override the i2c class. The class is used - by legacy i2c device drivers to find a bus in a specific context like - system management, video or sound. By default, I2C_CLASS_HWMON (1) is - being used. The definition of the classes can be found in - include/i2c/i2c.h - - Example, based on mpc823: - - i2c@860 { - compatible = "fsl,mpc823-i2c", - "fsl,cpm1-i2c"; - reg = <0x860 0x20 0x3c80 0x30>; - interrupts = <16>; - interrupt-parent = <&CPM_PIC>; - fsl,cpm-command = <0x10>; - #address-cells = <1>; - #size-cells = <0>; - - rtc@68 { - compatible = "dallas,ds1307"; - reg = <0x68>; - }; - }; - - m) Chipselect/Local Bus - - Properties: - - name : Should be localbus - - #address-cells : Should be either two or three. The first cell is the - chipselect number, and the remaining cells are the - offset into the chipselect. - - #size-cells : Either one or two, depending on how large each chipselect - can be. - - ranges : Each range corresponds to a single chipselect, and cover - the entire access window as configured. - - Example: - localbus@f0010100 { - compatible = "fsl,mpc8272-localbus", - "fsl,pq2-localbus"; - #address-cells = <2>; - #size-cells = <1>; - reg = ; - - ranges = <0 0 fe000000 02000000 - 1 0 f4500000 00008000>; - - flash@0,0 { - compatible = "jedec-flash"; - reg = <0 0 2000000>; - bank-width = <4>; - device-width = <1>; - }; - - board-control@1,0 { - reg = <1 0 20>; - compatible = "fsl,mpc8272ads-bcsr"; - }; - }; - - - n) 4xx/Axon EMAC ethernet nodes + d) 4xx/Axon EMAC ethernet nodes The EMAC ethernet controller in IBM and AMCC 4xx chips, and also the Axon bridge. To operate this needs to interact with a ths @@ -2387,7 +1495,7 @@ platforms are moved over to use the flattened-device-tree model. available. For Axon: 0x0000012a - o) Xilinx IP cores + e) Xilinx IP cores The Xilinx EDK toolchain ships with a set of IP cores (devices) for use in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range @@ -2681,206 +1789,7 @@ platforms are moved over to use the flattened-device-tree model. - reg-offset : A value of 3 is required - reg-shift : A value of 2 is required - - p) Freescale Synchronous Serial Interface - - The SSI is a serial device that communicates with audio codecs. It can - be programmed in AC97, I2S, left-justified, or right-justified modes. - - Required properties: - - compatible : compatible list, containing "fsl,ssi" - - cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on - - reg : offset and length of the register set for the device - - interrupts : where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - fsl,mode : the operating mode for the SSI interface - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master - - Optional properties: - - codec-handle : phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. - - Child 'codec' node required properties: - - compatible : compatible list, contains the name of the codec - - Child 'codec' node optional properties: - - clock-frequency : The frequency of the input clock, which typically - comes from an on-board dedicated oscillator. - - * Freescale 83xx DMA Controller - - Freescale PowerPC 83xx have on chip general purpose DMA controllers. - - Required properties: - - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" - - reg : - - ranges : Should be defined as specified in 1) to describe the - DMA controller channels. - - cell-index : controller index. 0 for controller @ 0x8100 - - interrupts : - - interrupt-parent : optional, if needed for interrupt mapping - - - - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel" - - reg : - - cell-index : dma channel index starts at 0. - - Optional properties: - - interrupts : - (on 83xx this is expected to be identical to - the interrupts property of the parent node) - - interrupt-parent : optional, if needed for interrupt mapping - - Example: - dma@82a8 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; - reg = <82a8 4>; - ranges = <0 8100 1a4>; - interrupt-parent = <&ipic>; - interrupts = <47 8>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <0>; - reg = <0 80>; - }; - dma-channel@80 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <1>; - reg = <80 80>; - }; - dma-channel@100 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <2>; - reg = <100 80>; - }; - dma-channel@180 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <3>; - reg = <180 80>; - }; - }; - - * Freescale 85xx/86xx DMA Controller - - Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. - - Required properties: - - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" - - reg : - - cell-index : controller index. 0 for controller @ 0x21000, - 1 for controller @ 0xc000 - - ranges : Should be defined as specified in 1) to describe the - DMA controller channels. - - - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel" - - cell-index : dma channel index starts at 0. - - reg : - - interrupts : - - interrupt-parent : optional, if needed for interrupt mapping - - Example: - dma@21300 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; - reg = <21300 4>; - ranges = <0 21100 200>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0 80>; - cell-index = <0>; - interrupt-parent = <&mpic>; - interrupts = <14 2>; - }; - dma-channel@80 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <80 80>; - cell-index = <1>; - interrupt-parent = <&mpic>; - interrupts = <15 2>; - }; - dma-channel@100 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <100 80>; - cell-index = <2>; - interrupt-parent = <&mpic>; - interrupts = <16 2>; - }; - dma-channel@180 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <180 80>; - cell-index = <3>; - interrupt-parent = <&mpic>; - interrupts = <17 2>; - }; - }; - - * Freescale 8xxx/3.0 Gb/s SATA nodes - - SATA nodes are defined to describe on-chip Serial ATA controllers. - Each SATA port should have its own node. - - Required properties: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-sata", where CHIP is the processor - (mpc8315, mpc8379, etc.) and the second is - "fsl,pq-sata" - - interrupts : - - cell-index : controller index. - 1 for controller @ 0x18000 - 2 for controller @ 0x19000 - 3 for controller @ 0x1a000 - 4 for controller @ 0x1b000 - - Optional properties: - - interrupt-parent : optional, if needed for interrupt mapping - - reg : - - Example: - - sata@18000 { - compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; - reg = <0x18000 0x1000>; - cell-index = <1>; - interrupts = <2c 8>; - interrupt-parent = < &ipic >; - }; - - q) USB EHCI controllers + f) USB EHCI controllers Required properties: - compatible : should be "usb-ehci". @@ -2906,109 +1815,6 @@ platforms are moved over to use the flattened-device-tree model. big-endian; }; - r) Freescale Display Interface Unit - - The Freescale DIU is a LCD controller, with proper hardware, it can also - drive DVI monitors. - - Required properties: - - compatible : should be "fsl-diu". - - reg : should contain at least address and length of the DIU register - set. - - Interrupts : one DIU interrupt should be describe here. - - Example (MPC8610HPCD) - display@2c000 { - compatible = "fsl,diu"; - reg = <0x2c000 100>; - interrupts = <72 2>; - interrupt-parent = <&mpic>; - }; - - s) Freescale on board FPGA - - This is the memory-mapped registers for on board FPGA. - - Required properities: - - compatible : should be "fsl,fpga-pixis". - - reg : should contain the address and the lenght of the FPPGA register - set. - - Example (MPC8610HPCD) - board-control@e8000000 { - compatible = "fsl,fpga-pixis"; - reg = <0xe8000000 32>; - }; - - t) Freescale MSI interrupt controller - - Reguired properities: - - compatible : compatible list, contains 2 entries, - first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, - etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on - the parent type. - - reg : should contain the address and the length of the shared message - interrupt register set. - - msi-available-ranges: use style section to define which - msi interrupt can be used in the 256 msi interrupts. This property is - optional, without this, all the 256 MSI interrupts can be used. - - interrupts : each one of the interrupts here is one entry per 32 MSIs, - and routed to the host interrupt controller. the interrupts should - be set as edge sensitive. - - interrupt-parent: the phandle for the interrupt controller - that services interrupts for this device. for 83xx cpu, the interrupts - are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed - to MPIC. - - Example - msi@41600 { - compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; - reg = <0x41600 0x80>; - msi-available-ranges = <0 0x100>; - interrupts = < - 0xe0 0 - 0xe1 0 - 0xe2 0 - 0xe3 0 - 0xe4 0 - 0xe5 0 - 0xe6 0 - 0xe7 0>; - interrupt-parent = <&mpic>; - }; - - u) Freescale General-purpose Timers Module - - Required properties: - - compatible : should be - "fsl,-gtm", "fsl,gtm" for SOC GTMs - "fsl,-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs - "fsl,-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs - - reg : should contain gtm registers location and length (0x40). - - interrupts : should contain four interrupts. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies the frequency driving the timer. - - Example: - - timer@500 { - compatible = "fsl,mpc8360-gtm", "fsl,gtm"; - reg = <0x500 0x40>; - interrupts = <90 8 78 8 84 8 72 8>; - interrupt-parent = <&ipic>; - /* filled by u-boot */ - clock-frequency = <0>; - }; - - timer@440 { - compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; - reg = <0x440 0x40>; - interrupts = <12 13 14 15>; - interrupt-parent = <&qeic>; - /* filled by u-boot */ - clock-frequency = <0>; - }; - VII - Marvell Discovery mv64[345]6x System Controller chips =========================================================== diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt new file mode 100644 index 00000000000..74ae6f1cd2d --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/board.txt @@ -0,0 +1,29 @@ +* Board Control and Status (BCSR) + +Required properties: + + - device_type : Should be "board-control" + - reg : Offset and length of the register set for the device + +Example: + + bcsr@f8000000 { + device_type = "board-control"; + reg = ; + }; + +* Freescale on board FPGA + +This is the memory-mapped registers for on board FPGA. + +Required properities: +- compatible : should be "fsl,fpga-pixis". +- reg : should contain the address and the lenght of the FPPGA register + set. + +Example (MPC8610HPCD): + + board-control@e8000000 { + compatible = "fsl,fpga-pixis"; + reg = <0xe8000000 32>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt new file mode 100644 index 00000000000..088fc471e03 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt @@ -0,0 +1,67 @@ +* Freescale Communications Processor Module + +NOTE: This is an interim binding, and will likely change slightly, +as more devices are supported. The QE bindings especially are +incomplete. + +* Root CPM node + +Properties: +- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". +- reg : A 48-byte region beginning with CPCR. + +Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30>; + } + +* Properties common to mulitple CPM/QE devices + +- fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + +- fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + +- reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + +* Multi-User RAM (MURAM) + +The multi-user/dual-ported RAM is expressed as a bus under the CPM node. + +Ranges must be set up subject to the following restrictions: + +- Children's reg nodes must be offsets from the start of all muram, even + if the user-data area does not begin at zero. +- If multiple range entries are used, the difference between the parent + address and the child address must be the same in all, so that a single + mapping can cover them all while maintaining the ability to determine + CPM-side offsets with pointer subtraction. It is recommended that + multiple range entries not be used. +- A child address of zero must be translatable, even if no reg resources + contain it. + +A child "data" node must exist, compatible with "fsl,cpm-muram-data", to +indicate the portion of muram that is usable by the OS for arbitrary +purposes. The data node may have an arbitrary number of reg resources, +all of which contribute to the allocatable muram pool. + +Example, based on mpc8272: + muram@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0 2000 9800 800>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt new file mode 100644 index 00000000000..4c7d45eaf02 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt @@ -0,0 +1,21 @@ +* Baud Rate Generators + +Currently defined compatibles: +fsl,cpm-brg +fsl,cpm1-brg +fsl,cpm2-brg + +Properties: +- reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. +- clock-frequency : Specifies the base frequency driving + the BRG. + +Example: + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = ; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt new file mode 100644 index 00000000000..87bc6048667 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt @@ -0,0 +1,41 @@ +* I2C + +The I2C controller is expressed as a bus under the CPM node. + +Properties: +- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" +- reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). +- #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. +- #size-cells : Should be zero. +- clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. +The following two properties are deprecated. They are only used by legacy +i2c drivers to find the bus to probe: +- linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. +- linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + +Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt new file mode 100644 index 00000000000..8e3ee168161 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt @@ -0,0 +1,18 @@ +* Interrupt Controllers + +Currently defined compatibles: +- fsl,cpm1-pic + - only one interrupt cell +- fsl,pq1-pic +- fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + +Example: + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt new file mode 100644 index 00000000000..74bfda4bb82 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt @@ -0,0 +1,15 @@ +* USB (Universal Serial Bus Controller) + +Properties: +- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + +Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = ; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt new file mode 100644 index 00000000000..0e426944658 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt @@ -0,0 +1,45 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt new file mode 100644 index 00000000000..78790d58dc2 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt @@ -0,0 +1,58 @@ +* Freescale QUICC Engine module (QE) +This represents qe module that is installed on PowerQUICC II Pro. + +NOTE: This is an interim binding; it should be updated to fit +in with the CPM binding later in this document. + +Basically, it is a bus of devices, that could act more or less +as a complete entity (UCC, USB etc ). All of them should be siblings on +the "root" qe node, using the common properties from there. +The description below applies to the qe of MPC8360 and +more nodes and properties would be extended in the future. + +i) Root QE device + +Required properties: +- compatible : should be "fsl,qe"; +- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" +- reg : offset and length of the device registers. +- bus-frequency : the clock frequency for QUICC Engine. + +Recommended properties +- brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + +Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,qe"; + ranges = <0 e0100000 00100000>; + reg = ; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + +* Multi-User RAM (MURAM) + +Required properties: +- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". +- mode : the could be "host" or "slave". +- ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. +- data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + +Example: + + muram@10000 { + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0 c000>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt new file mode 100644 index 00000000000..6c238f59b2a --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt @@ -0,0 +1,24 @@ +* Uploaded QE firmware + + If a new firwmare has been uploaded to the QE (usually by the + boot loader), then a 'firmware' child node should be added to the QE + node. This node provides information on the uploaded firmware that + device drivers may need. + + Required properties: + - id: The string name of the firmware. This is taken from the 'id' + member of the qe_firmware structure of the uploaded firmware. + Device drivers can search this string to determine if the + firmware they want is already present. + - extended-modes: The Extended Modes bitfield, taken from the + firmware binary. It is a 64-bit number represented + as an array of two 32-bit numbers. + - virtual-traps: The virtual traps, taken from the firmware binary. + It is an array of 8 32-bit numbers. + +Example: + firmware { + id = "Soft-UART"; + extended-modes = <0 0>; + virtual-traps = <0 0 0 0 0 0 0 0>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt new file mode 100644 index 00000000000..60984260207 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt @@ -0,0 +1,51 @@ +* Parallel I/O Ports + +This node configures Parallel I/O ports for CPUs with QE support. +The node should reside in the "soc" node of the tree. For each +device that using parallel I/O ports, a child node should be created. +See the definition of the Pin configuration nodes below for more +information. + +Required properties: +- device_type : should be "par_io". +- reg : offset to the register set and its length. +- num-ports : number of Parallel I/O ports + +Example: +par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + +Note that "par_io" nodes are obsolete, and should not be used for +the new device trees. Instead, each Par I/O bank should be represented +via its own gpio-controller node: + +Required properties: +- #gpio-cells : should be "2". +- compatible : should be "fsl,-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". +- reg : offset to the register set and its length. +- gpio-controller : node to identify gpio controllers. + +Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt new file mode 100644 index 00000000000..c5b43061db3 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt @@ -0,0 +1,60 @@ +* Pin configuration nodes + +Required properties: +- linux,phandle : phandle of this node; likely referenced by a QE + device. +- pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of external + interrupts. + +Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 00000000000..e47734bee3f --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = ; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt new file mode 100644 index 00000000000..c8f44d6bcbc --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt @@ -0,0 +1,22 @@ +* USB (Universal Serial Bus Controller) + +Required properties: +- compatible : could be "qe_udc" or "fhci-hcd". +- mode : the could be "host" or "slave". +- reg : Offset and length of the register set for the device +- interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example(slave): + usb@6c0 { + compatible = "qe_udc"; + reg = <6c0 40>; + interrupts = <8b 0>; + interrupt-parent = <700>; + mode = "slave"; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt new file mode 100644 index 00000000000..b35f3482e3e --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt @@ -0,0 +1,21 @@ +* Serial + +Currently defined compatibles: +- fsl,cpm1-smc-uart +- fsl,cpm2-smc-uart +- fsl,cpm1-scc-uart +- fsl,cpm2-scc-uart +- fsl,qe-uart + +Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/diu.txt b/Documentation/powerpc/dts-bindings/fsl/diu.txt new file mode 100644 index 00000000000..deb35de7098 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/diu.txt @@ -0,0 +1,18 @@ +* Freescale Display Interface Unit + +The Freescale DIU is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "fsl-diu". +- reg : should contain at least address and length of the DIU register + set. +- Interrupts : one DIU interrupt should be describe here. + +Example (MPC8610HPCD): + display@2c000 { + compatible = "fsl,diu"; + reg = <0x2c000 100>; + interrupts = <72 2>; + interrupt-parent = <&mpic>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt new file mode 100644 index 00000000000..86826df00e6 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt @@ -0,0 +1,127 @@ +* Freescale 83xx DMA Controller + +Freescale PowerPC 83xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8349, mpc8360, etc.) and the second is + "fsl,elo-dma" +- reg : +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. +- cell-index : controller index. 0 for controller @ 0x8100 +- interrupts : +- interrupt-parent : optional, if needed for interrupt mapping + + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8349, mpc8350, etc.) and the second is + "fsl,elo-dma-channel" + - reg : + - cell-index : dma channel index starts at 0. + +Optional properties: + - interrupts : + (on 83xx this is expected to be identical to + the interrupts property of the parent node) + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; + reg = <82a8 4>; + ranges = <0 8100 1a4>; + interrupt-parent = <&ipic>; + interrupts = <47 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <0>; + reg = <0 80>; + }; + dma-channel@80 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <1>; + reg = <80 80>; + }; + dma-channel@100 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <2>; + reg = <100 80>; + }; + dma-channel@180 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <3>; + reg = <180 80>; + }; + }; + +* Freescale 85xx/86xx DMA Controller + +Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8540, mpc8540, etc.) and the second is + "fsl,eloplus-dma" +- reg : +- cell-index : controller index. 0 for controller @ 0x21000, + 1 for controller @ 0xc000 +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8540, mpc8560, etc.) and the second is + "fsl,eloplus-dma-channel" + - cell-index : dma channel index starts at 0. + - reg : + - interrupts : + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; + reg = <21300 4>; + ranges = <0 21100 200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0 80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <14 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <80 80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <15 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <100 80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <16 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <180 80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <17 2>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/gtm.txt b/Documentation/powerpc/dts-bindings/fsl/gtm.txt new file mode 100644 index 00000000000..9a33efded4b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/gtm.txt @@ -0,0 +1,31 @@ +* Freescale General-purpose Timers Module + +Required properties: + - compatible : should be + "fsl,-gtm", "fsl,gtm" for SOC GTMs + "fsl,-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + +Example: + +timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; + +timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/powerpc/dts-bindings/fsl/guts.txt b/Documentation/powerpc/dts-bindings/fsl/guts.txt new file mode 100644 index 00000000000..9e7a2417dac --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/guts.txt @@ -0,0 +1,25 @@ +* Global Utilities Block + +The global utilities block controls power management, I/O device +enabling, power-on-reset configuration monitoring, general-purpose +I/O signal configuration, alternate function selection for multiplexed +signals, and clock control. + +Required properties: + + - compatible : Should define the compatible device type for + global-utilities. + - reg : Offset and length of the register set for the device. + +Recommended properties: + + - fsl,has-rstcr : Indicates that the global utilities register set + contains a functioning "reset control register" (i.e. the board + is wired to reset upon setting the HRESET_REQ bit in this register). + +Example: + global-utilities@e0000 { /* global utilities block */ + compatible = "fsl,mpc8548-guts"; + reg = ; + fsl,has-rstcr; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt new file mode 100644 index 00000000000..d0ab33e21fe --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt @@ -0,0 +1,32 @@ +* I2C + +Required properties : + + - device_type : Should be "i2c" + - reg : Offset and length of the register set for the device + +Recommended properties : + + - compatible : Should be "fsl-i2c" for parts compatible with + Freescale I2C specifications. + - interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - dfsrr : boolean; if defined, indicates that this I2C device has + a digital filter sampling rate register + - fsl5200-clocking : boolean; if defined, indicated that this device + uses the FSL 5200 clocking mechanism. + +Example : + i2c@3000 { + interrupt-parent = <40000>; + interrupts = <1b 3>; + reg = <3000 18>; + device_type = "i2c"; + compatible = "fsl-i2c"; + dfsrr; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/lbc.txt b/Documentation/powerpc/dts-bindings/fsl/lbc.txt new file mode 100644 index 00000000000..3300fec501c --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/lbc.txt @@ -0,0 +1,35 @@ +* Chipselect/Local Bus + +Properties: +- name : Should be localbus +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- ranges : Each range corresponds to a single chipselect, and cover + the entire access window as configured. + +Example: + localbus@f0010100 { + compatible = "fsl,mpc8272-localbus", + "fsl,pq2-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = ; + + ranges = <0 0 fe000000 02000000 + 1 0 f4500000 00008000>; + + flash@0,0 { + compatible = "jedec-flash"; + reg = <0 0 2000000>; + bank-width = <4>; + device-width = <1>; + }; + + board-control@1,0 { + reg = <1 0 20>; + compatible = "fsl,mpc8272ads-bcsr"; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt new file mode 100644 index 00000000000..b26b91992c5 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt @@ -0,0 +1,36 @@ +* Freescale MSI interrupt controller + +Reguired properities: +- compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. +- reg : should contain the address and the length of the shared message + interrupt register set. +- msi-available-ranges: use style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. +- interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. +- interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + +Example: + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/sata.txt b/Documentation/powerpc/dts-bindings/fsl/sata.txt new file mode 100644 index 00000000000..b46bcf46c3d --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/sata.txt @@ -0,0 +1,29 @@ +* Freescale 8xxx/3.0 Gb/s SATA nodes + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA port should have its own node. + +Required properties: +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-sata", where CHIP is the processor + (mpc8315, mpc8379, etc.) and the second is + "fsl,pq-sata" +- interrupts : +- cell-index : controller index. + 1 for controller @ 0x18000 + 2 for controller @ 0x19000 + 3 for controller @ 0x1a000 + 4 for controller @ 0x1b000 + +Optional properties: +- interrupt-parent : optional, if needed for interrupt mapping +- reg : + +Example: + sata@18000 { + compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; + reg = <0x18000 0x1000>; + cell-index = <1>; + interrupts = <2c 8>; + interrupt-parent = < &ipic >; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt new file mode 100644 index 00000000000..e7d9a344c4f --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt @@ -0,0 +1,24 @@ +* SPI (Serial Peripheral Interface) + +Required properties: +- cell-index : SPI controller index. +- compatible : should be "fsl,spi". +- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". +- reg : Offset and length of the register set for the device +- interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt new file mode 100644 index 00000000000..d100555d488 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt @@ -0,0 +1,38 @@ +Freescale Synchronous Serial Interface + +The SSI is a serial device that communicates with audio codecs. It can +be programmed in AC97, I2S, left-justified, or right-justified modes. + +Required properties: +- compatible : compatible list, containing "fsl,ssi" +- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on +- reg : offset and length of the register set for the device +- interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode : the operating mode for the SSI interface + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master + +Optional properties: +- codec-handle : phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. + +Child 'codec' node required properties: +- compatible : compatible list, contains the name of the codec + +Child 'codec' node optional properties: +- clock-frequency : The frequency of the input clock, which typically + comes from an on-board dedicated oscillator. diff --git a/Documentation/powerpc/dts-bindings/fsl/tsec.txt b/Documentation/powerpc/dts-bindings/fsl/tsec.txt new file mode 100644 index 00000000000..583ef6b56c4 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/tsec.txt @@ -0,0 +1,69 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node below for an example of how to define +a PHY. + +Required properties: + - reg : Offset and length of the register set for the device + - compatible : Should define the compatible device type for the + mdio. Currently, this is most likely to be "fsl,gianfar-mdio" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + + +* Gianfar-compatible ethernet nodes + +Required properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - mac-address : List of bytes representing the ethernet address of + this controller + - interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - phy-handle : The phandle for the PHY connected to this ethernet + controller. + - fixed-link : where a is emulated phy id - choose any, + but unique to the all specified fixed-links, b is duplex - 0 half, + 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no + pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. + +Recommended properties: + + - phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", + "tbi", or "rtbi". This property is only really needed if the connection + is of type "rgmii-id", as all other connection types are detected by + hardware. + + +Example: + ethernet@24000 { + #size-cells = <0>; + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <24000 1000>; + mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = ; + interrupt-parent = <40000>; + phy-handle = <2452000> + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/usb.txt b/Documentation/powerpc/dts-bindings/fsl/usb.txt new file mode 100644 index 00000000000..b0015240269 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/usb.txt @@ -0,0 +1,59 @@ +Freescale SOC USB controllers + +The device node for a USB controller that is part of a Freescale +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "fsl-usb2-mph" for multi port host USB + controllers, or "fsl-usb2-dr" for dual role USB controllers + - phy_type : For multi port host USB controllers, should be one of + "ulpi", or "serial". For dual role USB controllers, should be + one of "ulpi", "utmi", "utmi_wide", or "serial". + - reg : Offset and length of the register set for the device + - port0 : boolean; if defined, indicates port0 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port1" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - port1 : boolean; if defined, indicates port1 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port0" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible + controllers. Can be "host", "peripheral", or "otg". Default to + "host" if not defined for backward compatibility. + +Recommended properties : + - interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example multi port host USB controller device node : + usb@22000 { + compatible = "fsl-usb2-mph"; + reg = <22000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <27 1>; + phy_type = "ulpi"; + port0; + port1; + }; + +Example dual role USB controller device node : + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <23000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <26 1>; + dr_mode = "otg"; + phy = "ulpi"; + }; -- cgit v1.2.3 From 3fd44736db9a5bf33e4a216b9cd43c9cfd57c459 Mon Sep 17 00:00:00 2001 From: Kim Phillips Date: Tue, 8 Jul 2008 19:13:33 -0500 Subject: powerpc/fsl: update crypto node definition and device tree instances delete obsolete device-type property, delete model property (use compatible property instead), prepend "fsl," to Freescale specific properties. Add nodes to device trees that are missing them, and fix broken property values in other trees. Signed-off-by: Kim Phillips Signed-off-by: Kumar Gala --- Documentation/powerpc/dts-bindings/fsl/sec.txt | 68 ++++++++++++++++++++++++++ 1 file changed, 68 insertions(+) create mode 100644 Documentation/powerpc/dts-bindings/fsl/sec.txt (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/dts-bindings/fsl/sec.txt b/Documentation/powerpc/dts-bindings/fsl/sec.txt new file mode 100644 index 00000000000..2b6f2d45c45 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/sec.txt @@ -0,0 +1,68 @@ +Freescale SoC SEC Security Engines + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" +- reg : Offset and length of the register set for the device +- interrupts : the SEC's interrupt number +- fsl,num-channels : An integer representing the number of channels + available. +- fsl,channel-fifo-len : An integer representing the number of + descriptor pointers each channel fetch fifo can hold. +- fsl,exec-units-mask : The bitmask representing what execution units + (EUs) are available. It's a single 32-bit cell. EU information + should be encoded following the SEC's Descriptor Header Dword + EU_SEL0 field documentation, i.e. as follows: + + bit 0 = reserved - should be 0 + bit 1 = set if SEC has the ARC4 EU (AFEU) + bit 2 = set if SEC has the DES/3DES EU (DEU) + bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) + bit 4 = set if SEC has the random number generator EU (RNG) + bit 5 = set if SEC has the public key EU (PKEU) + bit 6 = set if SEC has the AES EU (AESU) + bit 7 = set if SEC has the Kasumi EU (KEU) + bit 8 = set if SEC has the CRC EU (CRCU) + bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) + +remaining bits are reserved for future SEC EUs. + +- fsl,descriptor-types-mask : The bitmask representing what descriptors + are available. It's a single 32-bit cell. Descriptor type information + should be encoded following the SEC's Descriptor Header Dword DESC_TYPE + field documentation, i.e. as follows: + + bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type + bit 1 = set if SEC supports the ipsec_esp descriptor type + bit 2 = set if SEC supports the common_nonsnoop desc. type + bit 3 = set if SEC supports the 802.11i AES ccmp desc. type + bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type + bit 5 = set if SEC supports the srtp descriptor type + bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type + bit 7 = set if SEC supports the pkeu_assemble descriptor type + bit 8 = set if SEC supports the aesu_key_expand_output desc.type + bit 9 = set if SEC supports the pkeu_ptmul descriptor type + bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type + bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type + + ..and so on and so forth. + +Optional properties: + +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + + /* MPC8548E */ + crypto@30000 { + compatible = "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <29 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0xfe>; + fsl,descriptor-types-mask = <0x12b0ebf>; + }; -- cgit v1.2.3