From 8d3b33f67fdc0fb364a1ef6d8fbbea7c2e4e6c98 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Sat, 25 Mar 2006 03:07:05 -0800 Subject: [PATCH] Remove MODULE_PARM MODULE_PARM was actually breaking: recent gcc version optimize them out as unused. It's time to replace the last users, which are generally in the most unloved drivers anyway. Signed-off-by: Rusty Russell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/sound/oss/Introduction | 2 +- Documentation/sound/oss/cs46xx | 16 ++++++++-------- 2 files changed, 9 insertions(+), 9 deletions(-) (limited to 'Documentation/sound') diff --git a/Documentation/sound/oss/Introduction b/Documentation/sound/oss/Introduction index 15d4fb975ac..f04ba6bb739 100644 --- a/Documentation/sound/oss/Introduction +++ b/Documentation/sound/oss/Introduction @@ -69,7 +69,7 @@ are available, for example IRQ, address, DMA. Warning, the options for different cards sometime use different names for the same or a similar feature (dma1= versus dma16=). As a last -resort, inspect the code (search for MODULE_PARM). +resort, inspect the code (search for module_param). Notes: diff --git a/Documentation/sound/oss/cs46xx b/Documentation/sound/oss/cs46xx index 88d6cf8b39f..b5443270986 100644 --- a/Documentation/sound/oss/cs46xx +++ b/Documentation/sound/oss/cs46xx @@ -88,7 +88,7 @@ parameters. for a copy email: twoller@crystal.cirrus.com MODULE_PARMS definitions ------------------------ -MODULE_PARM(defaultorder, "i"); +module_param(defaultorder, ulong, 0); defaultorder=N where N is a value from 1 to 12 The buffer order determines the size of the dma buffer for the driver. @@ -98,18 +98,18 @@ to not underrun the dma buffer as easily. As default, use 32k (order=3) rather than 64k as some of the games work more responsively. (2^N) * PAGE_SIZE = allocated buffer size -MODULE_PARM(cs_debuglevel, "i"); -MODULE_PARM(cs_debugmask, "i"); +module_param(cs_debuglevel, ulong, 0644); +module_param(cs_debugmask, ulong, 0644); cs_debuglevel=N cs_debugmask=0xMMMMMMMM where N is a value from 0 (no debug printfs), to 9 (maximum) 0xMMMMMMMM is a debug mask corresponding to the CS_xxx bits (see driver source). -MODULE_PARM(hercules_egpio_disable, "i"); +module_param(hercules_egpio_disable, ulong, 0); hercules_egpio_disable=N where N is a 0 (enable egpio), or a 1 (disable egpio support) -MODULE_PARM(initdelay, "i"); +module_param(initdelay, ulong, 0); initdelay=N This value is used to determine the millescond delay during the initialization code prior to powering up the PLL. On laptops this value can be used to @@ -118,19 +118,19 @@ system is booted under battery power then the mdelay()/udelay() functions fail t properly delay the required time. Also, if the system is booted under AC power and then the power removed, the mdelay()/udelay() functions will not delay properly. -MODULE_PARM(powerdown, "i"); +module_param(powerdown, ulong, 0); powerdown=N where N is 0 (disable any powerdown of the internal blocks) or 1 (enable powerdown) -MODULE_PARM(external_amp, "i"); +module_param(external_amp, bool, 0); external_amp=1 if N is set to 1, then force enabling the EAPD support in the primary AC97 codec. override the detection logic and force the external amp bit in the AC97 0x26 register to be reset (0). EAPD should be 0 for powerup, and 1 for powerdown. The VTB Santa Cruz card has inverted logic, so there is a special function for these cards. -MODULE_PARM(thinkpad, "i"); +module_param(thinkpad, bool, 0); thinkpad=1 if N is set to 1, then force enabling the clkrun functionality. Currently, when the part is being used, then clkrun is disabled for the entire system, -- cgit v1.2.3