From 23deb06821442506615f34bd92ccd6a2422629d7 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Fri, 30 May 2008 17:19:03 -0700 Subject: x86: move x86-specific documentation into Documentation/x86 The current organization of the x86 documentation makes it appear as if the "i386" documentation doesn't apply to x86-64, which is does. Thus, move that documentation into Documentation/x86, and move the x86-64-specific stuff into Documentation/x86/x86_64 with the eventual goal to move stuff that isn't actually 64-bit specific back into Documentation/x86. Signed-off-by: H. Peter Anvin --- Documentation/x86/x86_64/boot-options.txt | 314 ++++++++++++++++++++++++++++++ 1 file changed, 314 insertions(+) create mode 100644 Documentation/x86/x86_64/boot-options.txt (limited to 'Documentation/x86/x86_64/boot-options.txt') diff --git a/Documentation/x86/x86_64/boot-options.txt b/Documentation/x86/x86_64/boot-options.txt new file mode 100644 index 00000000000..b0c7b6c4abd --- /dev/null +++ b/Documentation/x86/x86_64/boot-options.txt @@ -0,0 +1,314 @@ +AMD64 specific boot options + +There are many others (usually documented in driver documentation), but +only the AMD64 specific ones are listed here. + +Machine check + + mce=off disable machine check + mce=bootlog Enable logging of machine checks left over from booting. + Disabled by default on AMD because some BIOS leave bogus ones. + If your BIOS doesn't do that it's a good idea to enable though + to make sure you log even machine check events that result + in a reboot. On Intel systems it is enabled by default. + mce=nobootlog + Disable boot machine check logging. + mce=tolerancelevel (number) + 0: always panic on uncorrected errors, log corrected errors + 1: panic or SIGBUS on uncorrected errors, log corrected errors + 2: SIGBUS or log uncorrected errors, log corrected errors + 3: never panic or SIGBUS, log all errors (for testing only) + Default is 1 + Can be also set using sysfs which is preferable. + + nomce (for compatibility with i386): same as mce=off + + Everything else is in sysfs now. + +APICs + + apic Use IO-APIC. Default + + noapic Don't use the IO-APIC. + + disableapic Don't use the local APIC + + nolapic Don't use the local APIC (alias for i386 compatibility) + + pirq=... See Documentation/i386/IO-APIC.txt + + noapictimer Don't set up the APIC timer + + no_timer_check Don't check the IO-APIC timer. This can work around + problems with incorrect timer initialization on some boards. + + apicmaintimer Run time keeping from the local APIC timer instead + of using the PIT/HPET interrupt for this. This is useful + when the PIT/HPET interrupts are unreliable. + + noapicmaintimer Don't do time keeping using the APIC timer. + Useful when this option was auto selected, but doesn't work. + + apicpmtimer + Do APIC timer calibration using the pmtimer. Implies + apicmaintimer. Useful when your PIT timer is totally + broken. + + disable_8254_timer / enable_8254_timer + Enable interrupt 0 timer routing over the 8254 in addition to over + the IO-APIC. The kernel tries to set a sensible default. + +Early Console + + syntax: earlyprintk=vga + earlyprintk=serial[,ttySn[,baudrate]] + + The early console is useful when the kernel crashes before the + normal console is initialized. It is not enabled by + default because it has some cosmetic problems. + Append ,keep to not disable it when the real console takes over. + Only vga or serial at a time, not both. + Currently only ttyS0 and ttyS1 are supported. + Interaction with the standard serial driver is not very good. + The VGA output is eventually overwritten by the real console. + +Timing + + notsc + Don't use the CPU time stamp counter to read the wall time. + This can be used to work around timing problems on multiprocessor systems + with not properly synchronized CPUs. + + report_lost_ticks + Report when timer interrupts are lost because some code turned off + interrupts for too long. + + nmi_watchdog=NUMBER[,panic] + NUMBER can be: + 0 don't use an NMI watchdog + 1 use the IO-APIC timer for the NMI watchdog + 2 use the local APIC for the NMI watchdog using a performance counter. Note + This will use one performance counter and the local APIC's performance + vector. + When panic is specified panic when an NMI watchdog timeout occurs. + This is useful when you use a panic=... timeout and need the box + quickly up again. + + nohpet + Don't use the HPET timer. + +Idle loop + + idle=poll + Don't do power saving in the idle loop using HLT, but poll for rescheduling + event. This will make the CPUs eat a lot more power, but may be useful + to get slightly better performance in multiprocessor benchmarks. It also + makes some profiling using performance counters more accurate. + Please note that on systems with MONITOR/MWAIT support (like Intel EM64T + CPUs) this option has no performance advantage over the normal idle loop. + It may also interact badly with hyperthreading. + +Rebooting + + reboot=b[ios] | t[riple] | k[bd] | a[cpi] | e[fi] [, [w]arm | [c]old] + bios Use the CPU reboot vector for warm reset + warm Don't set the cold reboot flag + cold Set the cold reboot flag + triple Force a triple fault (init) + kbd Use the keyboard controller. cold reset (default) + acpi Use the ACPI RESET_REG in the FADT. If ACPI is not configured or the + ACPI reset does not work, the reboot path attempts the reset using + the keyboard controller. + efi Use efi reset_system runtime service. If EFI is not configured or the + EFI reset does not work, the reboot path attempts the reset using + the keyboard controller. + + Using warm reset will be much faster especially on big memory + systems because the BIOS will not go through the memory check. + Disadvantage is that not all hardware will be completely reinitialized + on reboot so there may be boot problems on some systems. + + reboot=force + + Don't stop other CPUs on reboot. This can make reboot more reliable + in some cases. + +Non Executable Mappings + + noexec=on|off + + on Enable(default) + off Disable + +SMP + + additional_cpus=NUM Allow NUM more CPUs for hotplug + (defaults are specified by the BIOS, see Documentation/x86_64/cpu-hotplug-spec) + +NUMA + + numa=off Only set up a single NUMA node spanning all memory. + + numa=noacpi Don't parse the SRAT table for NUMA setup + + numa=fake=CMDLINE + If a number, fakes CMDLINE nodes and ignores NUMA setup of the + actual machine. Otherwise, system memory is configured + depending on the sizes and coefficients listed. For example: + numa=fake=2*512,1024,4*256,*128 + gives two 512M nodes, a 1024M node, four 256M nodes, and the + rest split into 128M chunks. If the last character of CMDLINE + is a *, the remaining memory is divided up equally among its + coefficient: + numa=fake=2*512,2* + gives two 512M nodes and the rest split into two nodes. + Otherwise, the remaining system RAM is allocated to an + additional node. + + numa=hotadd=percent + Only allow hotadd memory to preallocate page structures upto + percent of already available memory. + numa=hotadd=0 will disable hotadd memory. + +ACPI + + acpi=off Don't enable ACPI + acpi=ht Use ACPI boot table parsing, but don't enable ACPI + interpreter + acpi=force Force ACPI on (currently not needed) + + acpi=strict Disable out of spec ACPI workarounds. + + acpi_sci={edge,level,high,low} Set up ACPI SCI interrupt. + + acpi=noirq Don't route interrupts + +PCI + + pci=off Don't use PCI + pci=conf1 Use conf1 access. + pci=conf2 Use conf2 access. + pci=rom Assign ROMs. + pci=assign-busses Assign busses + pci=irqmask=MASK Set PCI interrupt mask to MASK + pci=lastbus=NUMBER Scan upto NUMBER busses, no matter what the mptable says. + pci=noacpi Don't use ACPI to set up PCI interrupt routing. + +IOMMU (input/output memory management unit) + + Currently four x86-64 PCI-DMA mapping implementations exist: + + 1. : use no hardware/software IOMMU at all + (e.g. because you have < 3 GB memory). + Kernel boot message: "PCI-DMA: Disabling IOMMU" + + 2. : AMD GART based hardware IOMMU. + Kernel boot message: "PCI-DMA: using GART IOMMU" + + 3. : Software IOMMU implementation. Used + e.g. if there is no hardware IOMMU in the system and it is need because + you have >3GB memory or told the kernel to us it (iommu=soft)) + Kernel boot message: "PCI-DMA: Using software bounce buffering + for IO (SWIOTLB)" + + 4. : IBM Calgary hardware IOMMU. Used in IBM + pSeries and xSeries servers. This hardware IOMMU supports DMA address + mapping with memory protection, etc. + Kernel boot message: "PCI-DMA: Using Calgary IOMMU" + + iommu=[][,noagp][,off][,force][,noforce][,leak[=] + [,memaper[=]][,merge][,forcesac][,fullflush][,nomerge] + [,noaperture][,calgary] + + General iommu options: + off Don't initialize and use any kind of IOMMU. + noforce Don't force hardware IOMMU usage when it is not needed. + (default). + force Force the use of the hardware IOMMU even when it is + not actually needed (e.g. because < 3 GB memory). + soft Use software bounce buffering (SWIOTLB) (default for + Intel machines). This can be used to prevent the usage + of an available hardware IOMMU. + + iommu options only relevant to the AMD GART hardware IOMMU: + Set the size of the remapping area in bytes. + allowed Overwrite iommu off workarounds for specific chipsets. + fullflush Flush IOMMU on each allocation (default). + nofullflush Don't use IOMMU fullflush. + leak Turn on simple iommu leak tracing (only when + CONFIG_IOMMU_LEAK is on). Default number of leak pages + is 20. + memaper[=] Allocate an own aperture over RAM with size 32MB<4GB. + DAC is used with 32-bit PCI to push a 64-bit address in + two cycles. When off all DMA over >4GB is forced through + an IOMMU or software bounce buffering. + nodac Forbid DAC mode, i.e. DMA >4GB. + panic Always panic when IOMMU overflows. + calgary Use the Calgary IOMMU if it is available + + iommu options only relevant to the software bounce buffering (SWIOTLB) IOMMU + implementation: + swiotlb=[,force] + Prereserve that many 128K pages for the software IO + bounce buffering. + force Force all IO through the software TLB. + + Settings for the IBM Calgary hardware IOMMU currently found in IBM + pSeries and xSeries machines: + + calgary=[64k,128k,256k,512k,1M,2M,4M,8M] + calgary=[translate_empty_slots] + calgary=[disable=] + panic Always panic when IOMMU overflows + + 64k,...,8M - Set the size of each PCI slot's translation table + when using the Calgary IOMMU. This is the size of the translation + table itself in main memory. The smallest table, 64k, covers an IO + space of 32MB; the largest, 8MB table, can cover an IO space of + 4GB. Normally the kernel will make the right choice by itself. + + translate_empty_slots - Enable translation even on slots that have + no devices attached to them, in case a device will be hotplugged + in the future. + + disable= - Disable translation on a given PHB. For + example, the built-in graphics adapter resides on the first bridge + (PCI bus number 0); if translation (isolation) is enabled on this + bridge, X servers that access the hardware directly from user + space might stop working. Use this option if you have devices that + are accessed from userspace directly on some PCI host bridge. + +Debugging + + oops=panic Always panic on oopses. Default is to just kill the process, + but there is a small probability of deadlocking the machine. + This will also cause panics on machine check exceptions. + Useful together with panic=30 to trigger a reboot. + + kstack=N Print N words from the kernel stack in oops dumps. + + pagefaulttrace Dump all page faults. Only useful for extreme debugging + and will create a lot of output. + + call_trace=[old|both|newfallback|new] + old: use old inexact backtracer + new: use new exact dwarf2 unwinder + both: print entries from both + newfallback: use new unwinder but fall back to old if it gets + stuck (default) + +Miscellaneous + + nogbpages + Do not use GB pages for kernel direct mappings. + gbpages + Use GB pages for kernel direct mappings. -- cgit v1.2.3