From 60ed7951d0c9bf8de8588384134f16474367b410 Mon Sep 17 00:00:00 2001
From: Alex <mailinglist@miromico.ch>
Date: Mon, 17 Mar 2008 14:55:06 +0100
Subject: avr32: Allow board to define oscillator rates

On our custom board we have other oscillator rates than on atngw100 and
atstk100x.

Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.

This patch moves them into board specific code.

Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 9 +--------
 1 file changed, 1 insertion(+), 8 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 0f24b4f85c1..34b56de4ea6 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -93,19 +93,12 @@ static struct clk devname##_##_name = {				\
 
 static DEFINE_SPINLOCK(pm_lock);
 
-unsigned long at32ap7000_osc_rates[3] = {
-	[0] = 32768,
-	/* FIXME: these are ATSTK1002-specific */
-	[1] = 20000000,
-	[2] = 12000000,
-};
-
 static struct clk osc0;
 static struct clk osc1;
 
 static unsigned long osc_get_rate(struct clk *clk)
 {
-	return at32ap7000_osc_rates[clk->index];
+	return at32_board_osc_rates[clk->index];
 }
 
 static unsigned long pll_get_rate(struct clk *clk, unsigned long control)
-- 
cgit v1.2.3


From aafafddb01e259cff61b3d3f5b3466f0a6a65b84 Mon Sep 17 00:00:00 2001
From: David Brownell <dbrownell@users.sourceforge.net>
Date: Tue, 10 Jun 2008 13:55:52 +0200
Subject: avr32: minor GPIO handling updates

On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/pio.c | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/pio.c b/arch/avr32/mach-at32ap/pio.c
index 38a8fa31c0b..60da03ba711 100644
--- a/arch/avr32/mach-at32ap/pio.c
+++ b/arch/avr32/mach-at32ap/pio.c
@@ -318,6 +318,8 @@ static void pio_bank_show(struct seq_file *s, struct gpio_chip *chip)
 		const char *label;
 
 		label = gpiochip_is_requested(chip, i);
+		if (!label && (imr & mask))
+			label = "[irq]";
 		if (!label)
 			continue;
 
-- 
cgit v1.2.3


From 47882cf620bcd7b014f6f7fc11be8c045787adac Mon Sep 17 00:00:00 2001
From: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Date: Tue, 5 Feb 2008 15:27:16 +0100
Subject: avr32: Add pin configuration choice to LCDC peripheral

This patch lets the board code choose which pin out to use for the LCD
interface.

On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.

Update ATSTK1002 and ATSTK1004 to use the new interface.

Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 105 +++++++++++++++++++++++++-----------
 1 file changed, 73 insertions(+), 32 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 34b56de4ea6..08115f9243f 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1257,7 +1257,8 @@ static struct clk atmel_lcdfb0_pixclk = {
 
 struct platform_device *__init
 at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
-		     unsigned long fbmem_start, unsigned long fbmem_len)
+		     unsigned long fbmem_start, unsigned long fbmem_len,
+		     unsigned int pin_config)
 {
 	struct platform_device *pdev;
 	struct atmel_lcdfb_info *info;
@@ -1284,37 +1285,77 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
 	switch (id) {
 	case 0:
 		pdev = &atmel_lcdfb0_device;
-		select_peripheral(PC(19), PERIPH_A, 0);	/* CC	  */
-		select_peripheral(PC(20), PERIPH_A, 0);	/* HSYNC  */
-		select_peripheral(PC(21), PERIPH_A, 0);	/* PCLK	  */
-		select_peripheral(PC(22), PERIPH_A, 0);	/* VSYNC  */
-		select_peripheral(PC(23), PERIPH_A, 0);	/* DVAL	  */
-		select_peripheral(PC(24), PERIPH_A, 0);	/* MODE	  */
-		select_peripheral(PC(25), PERIPH_A, 0);	/* PWR	  */
-		select_peripheral(PC(26), PERIPH_A, 0);	/* DATA0  */
-		select_peripheral(PC(27), PERIPH_A, 0);	/* DATA1  */
-		select_peripheral(PC(28), PERIPH_A, 0);	/* DATA2  */
-		select_peripheral(PC(29), PERIPH_A, 0);	/* DATA3  */
-		select_peripheral(PC(30), PERIPH_A, 0);	/* DATA4  */
-		select_peripheral(PC(31), PERIPH_A, 0);	/* DATA5  */
-		select_peripheral(PD(0),  PERIPH_A, 0);	/* DATA6  */
-		select_peripheral(PD(1),  PERIPH_A, 0);	/* DATA7  */
-		select_peripheral(PD(2),  PERIPH_A, 0);	/* DATA8  */
-		select_peripheral(PD(3),  PERIPH_A, 0);	/* DATA9  */
-		select_peripheral(PD(4),  PERIPH_A, 0);	/* DATA10 */
-		select_peripheral(PD(5),  PERIPH_A, 0);	/* DATA11 */
-		select_peripheral(PD(6),  PERIPH_A, 0);	/* DATA12 */
-		select_peripheral(PD(7),  PERIPH_A, 0);	/* DATA13 */
-		select_peripheral(PD(8),  PERIPH_A, 0);	/* DATA14 */
-		select_peripheral(PD(9),  PERIPH_A, 0);	/* DATA15 */
-		select_peripheral(PD(10), PERIPH_A, 0);	/* DATA16 */
-		select_peripheral(PD(11), PERIPH_A, 0);	/* DATA17 */
-		select_peripheral(PD(12), PERIPH_A, 0);	/* DATA18 */
-		select_peripheral(PD(13), PERIPH_A, 0);	/* DATA19 */
-		select_peripheral(PD(14), PERIPH_A, 0);	/* DATA20 */
-		select_peripheral(PD(15), PERIPH_A, 0);	/* DATA21 */
-		select_peripheral(PD(16), PERIPH_A, 0);	/* DATA22 */
-		select_peripheral(PD(17), PERIPH_A, 0);	/* DATA23 */
+
+		switch (pin_config) {
+		case 0:
+			select_peripheral(PC(19), PERIPH_A, 0);	/* CC	  */
+			select_peripheral(PC(20), PERIPH_A, 0);	/* HSYNC  */
+			select_peripheral(PC(21), PERIPH_A, 0);	/* PCLK	  */
+			select_peripheral(PC(22), PERIPH_A, 0);	/* VSYNC  */
+			select_peripheral(PC(23), PERIPH_A, 0);	/* DVAL	  */
+			select_peripheral(PC(24), PERIPH_A, 0);	/* MODE	  */
+			select_peripheral(PC(25), PERIPH_A, 0);	/* PWR	  */
+			select_peripheral(PC(26), PERIPH_A, 0);	/* DATA0  */
+			select_peripheral(PC(27), PERIPH_A, 0);	/* DATA1  */
+			select_peripheral(PC(28), PERIPH_A, 0);	/* DATA2  */
+			select_peripheral(PC(29), PERIPH_A, 0);	/* DATA3  */
+			select_peripheral(PC(30), PERIPH_A, 0);	/* DATA4  */
+			select_peripheral(PC(31), PERIPH_A, 0);	/* DATA5  */
+			select_peripheral(PD(0),  PERIPH_A, 0);	/* DATA6  */
+			select_peripheral(PD(1),  PERIPH_A, 0);	/* DATA7  */
+			select_peripheral(PD(2),  PERIPH_A, 0);	/* DATA8  */
+			select_peripheral(PD(3),  PERIPH_A, 0);	/* DATA9  */
+			select_peripheral(PD(4),  PERIPH_A, 0);	/* DATA10 */
+			select_peripheral(PD(5),  PERIPH_A, 0);	/* DATA11 */
+			select_peripheral(PD(6),  PERIPH_A, 0);	/* DATA12 */
+			select_peripheral(PD(7),  PERIPH_A, 0);	/* DATA13 */
+			select_peripheral(PD(8),  PERIPH_A, 0);	/* DATA14 */
+			select_peripheral(PD(9),  PERIPH_A, 0);	/* DATA15 */
+			select_peripheral(PD(10), PERIPH_A, 0);	/* DATA16 */
+			select_peripheral(PD(11), PERIPH_A, 0);	/* DATA17 */
+			select_peripheral(PD(12), PERIPH_A, 0);	/* DATA18 */
+			select_peripheral(PD(13), PERIPH_A, 0);	/* DATA19 */
+			select_peripheral(PD(14), PERIPH_A, 0);	/* DATA20 */
+			select_peripheral(PD(15), PERIPH_A, 0);	/* DATA21 */
+			select_peripheral(PD(16), PERIPH_A, 0);	/* DATA22 */
+			select_peripheral(PD(17), PERIPH_A, 0);	/* DATA23 */
+			break;
+		case 1:
+			select_peripheral(PE(0),  PERIPH_B, 0);	/* CC	  */
+			select_peripheral(PC(20), PERIPH_A, 0);	/* HSYNC  */
+			select_peripheral(PC(21), PERIPH_A, 0);	/* PCLK	  */
+			select_peripheral(PC(22), PERIPH_A, 0);	/* VSYNC  */
+			select_peripheral(PE(1),  PERIPH_B, 0);	/* DVAL	  */
+			select_peripheral(PE(2),  PERIPH_B, 0);	/* MODE	  */
+			select_peripheral(PC(25), PERIPH_A, 0);	/* PWR	  */
+			select_peripheral(PE(3),  PERIPH_B, 0);	/* DATA0  */
+			select_peripheral(PE(4),  PERIPH_B, 0);	/* DATA1  */
+			select_peripheral(PE(5),  PERIPH_B, 0);	/* DATA2  */
+			select_peripheral(PE(6),  PERIPH_B, 0);	/* DATA3  */
+			select_peripheral(PE(7),  PERIPH_B, 0);	/* DATA4  */
+			select_peripheral(PC(31), PERIPH_A, 0);	/* DATA5  */
+			select_peripheral(PD(0),  PERIPH_A, 0);	/* DATA6  */
+			select_peripheral(PD(1),  PERIPH_A, 0);	/* DATA7  */
+			select_peripheral(PE(8),  PERIPH_B, 0);	/* DATA8  */
+			select_peripheral(PE(9),  PERIPH_B, 0);	/* DATA9  */
+			select_peripheral(PE(10), PERIPH_B, 0);	/* DATA10 */
+			select_peripheral(PE(11), PERIPH_B, 0);	/* DATA11 */
+			select_peripheral(PE(12), PERIPH_B, 0);	/* DATA12 */
+			select_peripheral(PD(7),  PERIPH_A, 0);	/* DATA13 */
+			select_peripheral(PD(8),  PERIPH_A, 0);	/* DATA14 */
+			select_peripheral(PD(9),  PERIPH_A, 0);	/* DATA15 */
+			select_peripheral(PE(13), PERIPH_B, 0);	/* DATA16 */
+			select_peripheral(PE(14), PERIPH_B, 0);	/* DATA17 */
+			select_peripheral(PE(15), PERIPH_B, 0);	/* DATA18 */
+			select_peripheral(PE(16), PERIPH_B, 0);	/* DATA19 */
+			select_peripheral(PE(17), PERIPH_B, 0);	/* DATA20 */
+			select_peripheral(PE(18), PERIPH_B, 0);	/* DATA21 */
+			select_peripheral(PD(16), PERIPH_A, 0);	/* DATA22 */
+			select_peripheral(PD(17), PERIPH_A, 0);	/* DATA23 */
+			break;
+		default:
+			goto err_invalid_id;
+		}
 
 		clk_set_parent(&atmel_lcdfb0_pixclk, &pll0);
 		clk_set_rate(&atmel_lcdfb0_pixclk, clk_get_rate(&pll0));
-- 
cgit v1.2.3


From d86d314f67191011e6f494f6517b8cbd7dd3dc39 Mon Sep 17 00:00:00 2001
From: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Date: Mon, 25 Feb 2008 11:24:30 +0100
Subject: avr32: Add PSIF platform devices

This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.

The function for adding the PSIF platform device is also added to the
board header file.

Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 77 +++++++++++++++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 08115f9243f..a9ae7bb108b 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -833,6 +833,81 @@ void __init at32_add_system_devices(void)
 	platform_device_register(&pio4_device);
 }
 
+/* --------------------------------------------------------------------
+ *  PSIF
+ * -------------------------------------------------------------------- */
+static struct resource atmel_psif0_resource[] __initdata = {
+	{
+		.start	= 0xffe03c00,
+		.end	= 0xffe03cff,
+		.flags	= IORESOURCE_MEM,
+	},
+	IRQ(18),
+};
+static struct clk atmel_psif0_pclk = {
+	.name		= "pclk",
+	.parent		= &pba_clk,
+	.mode		= pba_clk_mode,
+	.get_rate	= pba_clk_get_rate,
+	.index		= 15,
+};
+
+static struct resource atmel_psif1_resource[] __initdata = {
+	{
+		.start	= 0xffe03d00,
+		.end	= 0xffe03dff,
+		.flags	= IORESOURCE_MEM,
+	},
+	IRQ(18),
+};
+static struct clk atmel_psif1_pclk = {
+	.name		= "pclk",
+	.parent		= &pba_clk,
+	.mode		= pba_clk_mode,
+	.get_rate	= pba_clk_get_rate,
+	.index		= 15,
+};
+
+struct platform_device *__init at32_add_device_psif(unsigned int id)
+{
+	struct platform_device *pdev;
+
+	if (!(id == 0 || id == 1))
+		return NULL;
+
+	pdev = platform_device_alloc("atmel_psif", id);
+	if (!pdev)
+		return NULL;
+
+	switch (id) {
+	case 0:
+		if (platform_device_add_resources(pdev, atmel_psif0_resource,
+					ARRAY_SIZE(atmel_psif0_resource)))
+			goto err_add_resources;
+		atmel_psif0_pclk.dev = &pdev->dev;
+		select_peripheral(PA(8), PERIPH_A, 0); /* CLOCK */
+		select_peripheral(PA(9), PERIPH_A, 0); /* DATA  */
+		break;
+	case 1:
+		if (platform_device_add_resources(pdev, atmel_psif1_resource,
+					ARRAY_SIZE(atmel_psif1_resource)))
+			goto err_add_resources;
+		atmel_psif1_pclk.dev = &pdev->dev;
+		select_peripheral(PB(11), PERIPH_A, 0); /* CLOCK */
+		select_peripheral(PB(12), PERIPH_A, 0); /* DATA  */
+		break;
+	default:
+		return NULL;
+	}
+
+	platform_device_add(pdev);
+	return pdev;
+
+err_add_resources:
+	platform_device_put(pdev);
+	return NULL;
+}
+
 /* --------------------------------------------------------------------
  *  USART
  * -------------------------------------------------------------------- */
@@ -1934,6 +2009,8 @@ struct clk *at32_clock_list[] = {
 	&pio4_mck,
 	&at32_tcb0_t0_clk,
 	&at32_tcb1_t0_clk,
+	&atmel_psif0_pclk,
+	&atmel_psif1_pclk,
 	&atmel_usart0_usart,
 	&atmel_usart1_usart,
 	&atmel_usart2_usart,
-- 
cgit v1.2.3


From 9c2baf785e90419d6f9af6bd07aa0694020cba8d Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Wed, 18 Jun 2008 02:31:43 -0700
Subject: at32ap700x spi: enable pullups on MISO

This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to

  (a) ensure a fixed data value for missing or input-only slaves;

  (b) prevent power waste associated with inputs floating near VDDIO/2.

Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns.  Were there trouble, board-specific code could turn off
the relevant pullup(s).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index a9ae7bb108b..a2e7b96b5e8 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1181,7 +1181,8 @@ at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n)
 	switch (id) {
 	case 0:
 		pdev = &atmel_spi0_device;
-		select_peripheral(PA(0),  PERIPH_A, 0);	/* MISO	 */
+		/* pullup MISO so a level is always defined */
+		select_peripheral(PA(0),  PERIPH_A, AT32_GPIOF_PULLUP);
 		select_peripheral(PA(1),  PERIPH_A, 0);	/* MOSI	 */
 		select_peripheral(PA(2),  PERIPH_A, 0);	/* SCK	 */
 		at32_spi_setup_slaves(0, b, n, spi0_pins);
@@ -1189,7 +1190,8 @@ at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n)
 
 	case 1:
 		pdev = &atmel_spi1_device;
-		select_peripheral(PB(0),  PERIPH_B, 0);	/* MISO  */
+		/* pullup MISO so a level is always defined */
+		select_peripheral(PB(0),  PERIPH_B, AT32_GPIOF_PULLUP);
 		select_peripheral(PB(1),  PERIPH_B, 0);	/* MOSI  */
 		select_peripheral(PB(5),  PERIPH_B, 0);	/* SCK   */
 		at32_spi_setup_slaves(1, b, n, spi1_pins);
-- 
cgit v1.2.3


From 8405996ff6d89bbf275a206eb69d10b98a8d5257 Mon Sep 17 00:00:00 2001
From: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Date: Wed, 25 Jun 2008 10:32:50 +0200
Subject: atmel_pwm: Rename the "mck" clock to "pwm_clk"

The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index a2e7b96b5e8..2f208eb4d3c 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1471,7 +1471,7 @@ static struct resource atmel_pwm0_resource[] __initdata = {
 	IRQ(24),
 };
 static struct clk atmel_pwm0_mck = {
-	.name		= "mck",
+	.name		= "pwm_clk",
 	.parent		= &pbb_clk,
 	.mode		= pbb_clk_mode,
 	.get_rate	= pbb_clk_get_rate,
-- 
cgit v1.2.3


From 65033ed740ef06eddf9fde7a992eab336cbddd56 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Tue, 4 Mar 2008 15:15:00 +0100
Subject: avr32: Move setup_platform() into chip-specific file

Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap.c     |  8 --------
 arch/avr32/mach-at32ap/at32ap700x.c | 18 ++++++++----------
 2 files changed, 8 insertions(+), 18 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap.c b/arch/avr32/mach-at32ap/at32ap.c
index 7c4987f3287..1040bda4fda 100644
--- a/arch/avr32/mach-at32ap/at32ap.c
+++ b/arch/avr32/mach-at32ap/at32ap.c
@@ -11,14 +11,6 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
-#include <asm/arch/init.h>
-
-void __init setup_platform(void)
-{
-	at32_clock_init();
-	at32_portmux_init();
-}
-
 static int __init pdc_probe(struct platform_device *pdev)
 {
 	struct clk *pclk, *hclk;
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 2f208eb4d3c..baf4680b498 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -2048,16 +2048,7 @@ struct clk *at32_clock_list[] = {
 };
 unsigned int at32_nr_clocks = ARRAY_SIZE(at32_clock_list);
 
-void __init at32_portmux_init(void)
-{
-	at32_init_pio(&pio0_device);
-	at32_init_pio(&pio1_device);
-	at32_init_pio(&pio2_device);
-	at32_init_pio(&pio3_device);
-	at32_init_pio(&pio4_device);
-}
-
-void __init at32_clock_init(void)
+void __init setup_platform(void)
 {
 	u32 cpu_mask = 0, hsb_mask = 0, pba_mask = 0, pbb_mask = 0;
 	int i;
@@ -2112,4 +2103,11 @@ void __init at32_clock_init(void)
 	pm_writel(HSB_MASK, hsb_mask);
 	pm_writel(PBA_MASK, pba_mask);
 	pm_writel(PBB_MASK, pbb_mask);
+
+	/* Initialize the port muxes */
+	at32_init_pio(&pio0_device);
+	at32_init_pio(&pio1_device);
+	at32_init_pio(&pio2_device);
+	at32_init_pio(&pio3_device);
+	at32_init_pio(&pio4_device);
 }
-- 
cgit v1.2.3


From d7ff2a4a28ceadc03df2f5a20897165fda306382 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Tue, 4 Mar 2008 15:16:57 +0100
Subject: avr32: Rename at32ap.c -> pdc.c

The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/Makefile |  2 +-
 arch/avr32/mach-at32ap/at32ap.c | 48 -----------------------------------------
 arch/avr32/mach-at32ap/pdc.c    | 48 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 49 insertions(+), 49 deletions(-)
 delete mode 100644 arch/avr32/mach-at32ap/at32ap.c
 create mode 100644 arch/avr32/mach-at32ap/pdc.c

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/Makefile b/arch/avr32/mach-at32ap/Makefile
index e89009439e4..cb44182d386 100644
--- a/arch/avr32/mach-at32ap/Makefile
+++ b/arch/avr32/mach-at32ap/Makefile
@@ -1,3 +1,3 @@
-obj-y				+= at32ap.o clock.o intc.o extint.o pio.o hsmc.o
+obj-y				+= pdc.o clock.o intc.o extint.o pio.o hsmc.o
 obj-$(CONFIG_CPU_AT32AP700X)	+= at32ap700x.o pm-at32ap700x.o
 obj-$(CONFIG_CPU_FREQ_AT32AP)	+= cpufreq.o
diff --git a/arch/avr32/mach-at32ap/at32ap.c b/arch/avr32/mach-at32ap/at32ap.c
deleted file mode 100644
index 1040bda4fda..00000000000
--- a/arch/avr32/mach-at32ap/at32ap.c
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-static int __init pdc_probe(struct platform_device *pdev)
-{
-	struct clk *pclk, *hclk;
-
-	pclk = clk_get(&pdev->dev, "pclk");
-	if (IS_ERR(pclk)) {
-		dev_err(&pdev->dev, "no pclk defined\n");
-		return PTR_ERR(pclk);
-	}
-	hclk = clk_get(&pdev->dev, "hclk");
-	if (IS_ERR(hclk)) {
-		dev_err(&pdev->dev, "no hclk defined\n");
-		clk_put(pclk);
-		return PTR_ERR(hclk);
-	}
-
-	clk_enable(pclk);
-	clk_enable(hclk);
-
-	dev_info(&pdev->dev, "Atmel Peripheral DMA Controller enabled\n");
-	return 0;
-}
-
-static struct platform_driver pdc_driver = {
-	.probe		= pdc_probe,
-	.driver		= {
-		.name	= "pdc",
-	},
-};
-
-static int __init pdc_init(void)
-{
-	return platform_driver_register(&pdc_driver);
-}
-arch_initcall(pdc_init);
diff --git a/arch/avr32/mach-at32ap/pdc.c b/arch/avr32/mach-at32ap/pdc.c
new file mode 100644
index 00000000000..1040bda4fda
--- /dev/null
+++ b/arch/avr32/mach-at32ap/pdc.c
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+static int __init pdc_probe(struct platform_device *pdev)
+{
+	struct clk *pclk, *hclk;
+
+	pclk = clk_get(&pdev->dev, "pclk");
+	if (IS_ERR(pclk)) {
+		dev_err(&pdev->dev, "no pclk defined\n");
+		return PTR_ERR(pclk);
+	}
+	hclk = clk_get(&pdev->dev, "hclk");
+	if (IS_ERR(hclk)) {
+		dev_err(&pdev->dev, "no hclk defined\n");
+		clk_put(pclk);
+		return PTR_ERR(hclk);
+	}
+
+	clk_enable(pclk);
+	clk_enable(hclk);
+
+	dev_info(&pdev->dev, "Atmel Peripheral DMA Controller enabled\n");
+	return 0;
+}
+
+static struct platform_driver pdc_driver = {
+	.probe		= pdc_probe,
+	.driver		= {
+		.name	= "pdc",
+	},
+};
+
+static int __init pdc_init(void)
+{
+	return platform_driver_register(&pdc_driver);
+}
+arch_initcall(pdc_init);
-- 
cgit v1.2.3


From 7951f188a0b7f9b2f181c692efb0d31082bec346 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed, 5 Mar 2008 15:08:27 +0100
Subject: avr32: Enable SDRAMC clock at startup

The SDRAM controller needs a clock in order to respond to our
commands, and suspend doesn't work very well without the SDRAM in
self-refresh mode.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 9 +++++++++
 1 file changed, 9 insertions(+)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index baf4680b498..3ee5e727879 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -675,6 +675,14 @@ static struct clk hramc_clk = {
 	.users		= 1,
 	.index		= 3,
 };
+static struct clk sdramc_clk = {
+	.name		= "sdramc_clk",
+	.parent		= &pbb_clk,
+	.mode		= pbb_clk_mode,
+	.get_rate	= pbb_clk_get_rate,
+	.users		= 1,
+	.index		= 14,
+};
 
 static struct resource smc0_resource[] = {
 	PBMEM(0xfff03400),
@@ -1998,6 +2006,7 @@ struct clk *at32_clock_list[] = {
 	&hmatrix_clk,
 	&ebi_clk,
 	&hramc_clk,
+	&sdramc_clk,
 	&smc0_pclk,
 	&smc0_mck,
 	&pdc_hclk,
-- 
cgit v1.2.3


From b83d6ee17588f1a4fbfc8ef0451b0900a5ef5950 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed, 5 Mar 2008 10:00:28 +0100
Subject: avr32: Add simple SRAM allocator

Add SRAM allocator for avr32, which is just a thin wrapper around
genalloc.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 3ee5e727879..07b21b121ee 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -20,6 +20,7 @@
 #include <asm/arch/at32ap700x.h>
 #include <asm/arch/board.h>
 #include <asm/arch/portmux.h>
+#include <asm/arch/sram.h>
 
 #include <video/atmel_lcdc.h>
 
@@ -2120,3 +2121,28 @@ void __init setup_platform(void)
 	at32_init_pio(&pio3_device);
 	at32_init_pio(&pio4_device);
 }
+
+struct gen_pool *sram_pool;
+
+static int __init sram_init(void)
+{
+	struct gen_pool *pool;
+
+	/* 1KiB granularity */
+	pool = gen_pool_create(10, -1);
+	if (!pool)
+		goto fail;
+
+	if (gen_pool_add(pool, 0x24000000, 0x8000, -1))
+		goto err_pool_add;
+
+	sram_pool = pool;
+	return 0;
+
+err_pool_add:
+	gen_pool_destroy(pool);
+fail:
+	pr_err("Failed to create SRAM pool\n");
+	return -ENOMEM;
+}
+core_initcall(sram_init);
-- 
cgit v1.2.3


From aa8e87ca619a3d1944874e85d74fda90607c73b9 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun, 24 Feb 2008 14:26:03 +0100
Subject: avr32: Add system device for the internal interrupt controller (intc)

This makes the intc show up in sysfs (probably not very useful), and
allows us to easily add suspend/resume support later.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/intc.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/intc.c b/arch/avr32/mach-at32ap/intc.c
index 097cf4e8405..644a3fb8c16 100644
--- a/arch/avr32/mach-at32ap/intc.c
+++ b/arch/avr32/mach-at32ap/intc.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2006 Atmel Corporation
+ * Copyright (C) 2006, 2008 Atmel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -12,14 +12,16 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/platform_device.h>
+#include <linux/sysdev.h>
 
 #include <asm/io.h>
 
 #include "intc.h"
 
 struct intc {
-	void __iomem	*regs;
-	struct irq_chip	chip;
+	void __iomem		*regs;
+	struct irq_chip		chip;
+	struct sys_device	sysdev;
 };
 
 extern struct platform_device at32_intc0_device;
@@ -136,6 +138,26 @@ fail:
 	panic("Interrupt controller initialization failed!\n");
 }
 
+static struct sysdev_class intc_class = {
+	.name	= "intc",
+};
+
+static int __init intc_init_sysdev(void)
+{
+	int ret;
+
+	ret = sysdev_class_register(&intc_class);
+	if (ret)
+		return ret;
+
+	intc0.sysdev.id = 0;
+	intc0.sysdev.cls = &intc_class;
+	ret = sysdev_register(&intc0.sysdev);
+
+	return ret;
+}
+device_initcall(intc_init_sysdev);
+
 unsigned long intc_get_pending(unsigned int group)
 {
 	return intc_readl(&intc0, INTREQ0 + 4 * group);
-- 
cgit v1.2.3


From 02a00cf672a37292c31bbdde191712bfa40a4f1d Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun, 24 Feb 2008 13:51:38 +0100
Subject: avr32: Power Management support ("standby" and "mem" modes)

Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)

Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)

The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.

We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/Makefile        |   5 +
 arch/avr32/mach-at32ap/intc.c          |  54 +++++++-
 arch/avr32/mach-at32ap/pm-at32ap700x.S | 108 +++++++++++++++
 arch/avr32/mach-at32ap/pm.c            | 245 +++++++++++++++++++++++++++++++++
 arch/avr32/mach-at32ap/sdramc.h        |  76 ++++++++++
 5 files changed, 487 insertions(+), 1 deletion(-)
 create mode 100644 arch/avr32/mach-at32ap/pm.c
 create mode 100644 arch/avr32/mach-at32ap/sdramc.h

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/Makefile b/arch/avr32/mach-at32ap/Makefile
index cb44182d386..d5018e2eed2 100644
--- a/arch/avr32/mach-at32ap/Makefile
+++ b/arch/avr32/mach-at32ap/Makefile
@@ -1,3 +1,8 @@
 obj-y				+= pdc.o clock.o intc.o extint.o pio.o hsmc.o
 obj-$(CONFIG_CPU_AT32AP700X)	+= at32ap700x.o pm-at32ap700x.o
 obj-$(CONFIG_CPU_FREQ_AT32AP)	+= cpufreq.o
+obj-$(CONFIG_PM)		+= pm.o
+
+ifeq ($(CONFIG_PM_DEBUG),y)
+CFLAGS_pm.o	+= -DDEBUG
+endif
diff --git a/arch/avr32/mach-at32ap/intc.c b/arch/avr32/mach-at32ap/intc.c
index 644a3fb8c16..994c4545e2b 100644
--- a/arch/avr32/mach-at32ap/intc.c
+++ b/arch/avr32/mach-at32ap/intc.c
@@ -22,6 +22,10 @@ struct intc {
 	void __iomem		*regs;
 	struct irq_chip		chip;
 	struct sys_device	sysdev;
+#ifdef CONFIG_PM
+	unsigned long		suspend_ipr;
+	unsigned long		saved_ipr[64];
+#endif
 };
 
 extern struct platform_device at32_intc0_device;
@@ -138,8 +142,56 @@ fail:
 	panic("Interrupt controller initialization failed!\n");
 }
 
+#ifdef CONFIG_PM
+void intc_set_suspend_handler(unsigned long offset)
+{
+	intc0.suspend_ipr = offset;
+}
+
+static int intc_suspend(struct sys_device *sdev, pm_message_t state)
+{
+	struct intc *intc = container_of(sdev, struct intc, sysdev);
+	int i;
+
+	if (unlikely(!irqs_disabled())) {
+		pr_err("intc_suspend: called with interrupts enabled\n");
+		return -EINVAL;
+	}
+
+	if (unlikely(!intc->suspend_ipr)) {
+		pr_err("intc_suspend: suspend_ipr not initialized\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < 64; i++) {
+		intc->saved_ipr[i] = intc_readl(intc, INTPR0 + 4 * i);
+		intc_writel(intc, INTPR0 + 4 * i, intc->suspend_ipr);
+	}
+
+	return 0;
+}
+
+static int intc_resume(struct sys_device *sdev)
+{
+	struct intc *intc = container_of(sdev, struct intc, sysdev);
+	int i;
+
+	WARN_ON(!irqs_disabled());
+
+	for (i = 0; i < 64; i++)
+		intc_writel(intc, INTPR0 + 4 * i, intc->saved_ipr[i]);
+
+	return 0;
+}
+#else
+#define intc_suspend	NULL
+#define intc_resume	NULL
+#endif
+
 static struct sysdev_class intc_class = {
-	.name	= "intc",
+	.name		= "intc",
+	.suspend	= intc_suspend,
+	.resume		= intc_resume,
 };
 
 static int __init intc_init_sysdev(void)
diff --git a/arch/avr32/mach-at32ap/pm-at32ap700x.S b/arch/avr32/mach-at32ap/pm-at32ap700x.S
index 949e2485e27..0a53ad314ff 100644
--- a/arch/avr32/mach-at32ap/pm-at32ap700x.S
+++ b/arch/avr32/mach-at32ap/pm-at32ap700x.S
@@ -12,6 +12,12 @@
 #include <asm/thread_info.h>
 #include <asm/arch/pm.h>
 
+#include "pm.h"
+#include "sdramc.h"
+
+/* Same as 0xfff00000 but fits in a 21 bit signed immediate */
+#define PM_BASE	-0x100000
+
 	.section .bss, "wa", @nobits
 	.global	disable_idle_sleep
 	.type	disable_idle_sleep, @object
@@ -64,3 +70,105 @@ cpu_idle_skip_sleep:
 	unmask_interrupts
 	retal	r12
 	.size	cpu_idle_skip_sleep, . - cpu_idle_skip_sleep
+
+#ifdef CONFIG_PM
+	.section .init.text, "ax", @progbits
+
+	.global	pm_exception
+	.type	pm_exception, @function
+pm_exception:
+	/*
+	 * Exceptions are masked when we switch to this handler, so
+	 * we'll only get "unrecoverable" exceptions (offset 0.)
+	 */
+	sub	r12, pc, . - .Lpanic_msg
+	lddpc	pc, .Lpanic_addr
+
+	.align	2
+.Lpanic_addr:
+	.long	panic
+.Lpanic_msg:
+	.asciz	"Unrecoverable exception during suspend\n"
+	.size	pm_exception, . - pm_exception
+
+	.global	pm_irq0
+	.type	pm_irq0, @function
+pm_irq0:
+	/* Disable interrupts and return after the sleep instruction */
+	mfsr	r9, SYSREG_RSR_INT0
+	mtsr	SYSREG_RAR_INT0, r8
+	sbr	r9, SYSREG_GM_OFFSET
+	mtsr	SYSREG_RSR_INT0, r9
+	rete
+
+	/*
+	 * void cpu_enter_standby(unsigned long sdramc_base)
+	 *
+	 * Enter PM_SUSPEND_STANDBY mode. At this point, all drivers
+	 * are suspended and interrupts are disabled. Interrupts
+	 * marked as 'wakeup' event sources may still come along and
+	 * get us out of here.
+	 *
+	 * The SDRAM will be put into self-refresh mode (which does
+	 * not require a clock from the CPU), and the CPU will be put
+	 * into "frozen" mode (HSB bus stopped). The SDRAM controller
+	 * will automatically bring the SDRAM into normal mode on the
+	 * first access, and the power manager will automatically
+	 * start the HSB and CPU clocks upon a wakeup event.
+	 *
+	 * This code uses the same "skip sleep" technique as above.
+	 * It is very important that we jump directly to
+	 * cpu_after_sleep after the sleep instruction since that's
+	 * where we'll end up if the interrupt handler decides that we
+	 * need to skip the sleep instruction.
+	 */
+	.global	pm_standby
+	.type	pm_standby, @function
+pm_standby:
+	/*
+	 * interrupts are already masked at this point, and EVBA
+	 * points to pm_exception above.
+	 */
+	ld.w	r10, r12[SDRAMC_LPR]
+	sub	r8, pc, . - 1f		/* return address for irq handler */
+	mov	r11, SDRAMC_LPR_LPCB_SELF_RFR
+	bfins	r10, r11, 0, 2		/* LPCB <- self Refresh */
+	sync	0			/* flush write buffer */
+	st.w	r12[SDRAMC_LPR], r11	/* put SDRAM in self-refresh mode */
+	ld.w	r11, r12[SDRAMC_LPR]
+	unmask_interrupts
+	sleep	CPU_SLEEP_FROZEN
+1:	mask_interrupts
+	retal	r12
+	.size	pm_standby, . - pm_standby
+
+	.global	pm_suspend_to_ram
+	.type	pm_suspend_to_ram, @function
+pm_suspend_to_ram:
+	/*
+	 * interrupts are already masked at this point, and EVBA
+	 * points to pm_exception above.
+	 */
+	mov	r11, 0
+	cache	r11[2], 8		/* clean all dcache lines */
+	sync	0			/* flush write buffer */
+	ld.w	r10, r12[SDRAMC_LPR]
+	sub	r8, pc, . - 1f		/* return address for irq handler */
+	mov	r11, SDRAMC_LPR_LPCB_SELF_RFR
+	bfins	r10, r11, 0, 2		/* LPCB <- self refresh */
+	st.w	r12[SDRAMC_LPR], r10	/* put SDRAM in self-refresh mode */
+	ld.w	r11, r12[SDRAMC_LPR]
+
+	unmask_interrupts
+	sleep	CPU_SLEEP_STOP
+1:	mask_interrupts
+
+	retal	r12
+	.size	pm_suspend_to_ram, . - pm_suspend_to_ram
+
+	.global	pm_sram_end
+	.type	pm_sram_end, @function
+pm_sram_end:
+	.size	pm_sram_end, 0
+
+#endif /* CONFIG_PM */
diff --git a/arch/avr32/mach-at32ap/pm.c b/arch/avr32/mach-at32ap/pm.c
new file mode 100644
index 00000000000..0b764320135
--- /dev/null
+++ b/arch/avr32/mach-at32ap/pm.c
@@ -0,0 +1,245 @@
+/*
+ * AVR32 AP Power Management
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+#include <linux/io.h>
+#include <linux/suspend.h>
+#include <linux/vmalloc.h>
+
+#include <asm/cacheflush.h>
+#include <asm/sysreg.h>
+
+#include <asm/arch/pm.h>
+#include <asm/arch/sram.h>
+
+/* FIXME: This is only valid for AP7000 */
+#define SDRAMC_BASE	0xfff03800
+
+#include "sdramc.h"
+
+#define SRAM_PAGE_FLAGS	(SYSREG_BIT(TLBELO_D) | SYSREG_BF(SZ, 1)	\
+				| SYSREG_BF(AP, 3) | SYSREG_BIT(G))
+
+
+static unsigned long	pm_sram_start;
+static size_t		pm_sram_size;
+static struct vm_struct	*pm_sram_area;
+
+static void (*avr32_pm_enter_standby)(unsigned long sdramc_base);
+static void (*avr32_pm_enter_str)(unsigned long sdramc_base);
+
+/*
+ * Must be called with interrupts disabled. Exceptions will be masked
+ * on return (i.e. all exceptions will be "unrecoverable".)
+ */
+static void *avr32_pm_map_sram(void)
+{
+	unsigned long	vaddr;
+	unsigned long	page_addr;
+	u32		tlbehi;
+	u32		mmucr;
+
+	vaddr = (unsigned long)pm_sram_area->addr;
+	page_addr = pm_sram_start & PAGE_MASK;
+
+	/*
+	 * Mask exceptions and grab the first TLB entry. We won't be
+	 * needing it while sleeping.
+	 */
+	asm volatile("ssrf	%0" : : "i"(SYSREG_EM_OFFSET) : "memory");
+
+	mmucr = sysreg_read(MMUCR);
+	tlbehi = sysreg_read(TLBEHI);
+	sysreg_write(MMUCR, SYSREG_BFINS(DRP, 0, mmucr));
+
+	tlbehi = SYSREG_BF(ASID, SYSREG_BFEXT(ASID, tlbehi));
+	tlbehi |= vaddr & PAGE_MASK;
+	tlbehi |= SYSREG_BIT(TLBEHI_V);
+
+	sysreg_write(TLBELO, page_addr | SRAM_PAGE_FLAGS);
+	sysreg_write(TLBEHI, tlbehi);
+	__builtin_tlbw();
+
+	return (void *)(vaddr + pm_sram_start - page_addr);
+}
+
+/*
+ * Must be called with interrupts disabled. Exceptions will be
+ * unmasked on return.
+ */
+static void avr32_pm_unmap_sram(void)
+{
+	u32	mmucr;
+	u32	tlbehi;
+	u32	tlbarlo;
+
+	/* Going to update TLB entry at index 0 */
+	mmucr = sysreg_read(MMUCR);
+	tlbehi = sysreg_read(TLBEHI);
+	sysreg_write(MMUCR, SYSREG_BFINS(DRP, 0, mmucr));
+
+	/* Clear the "valid" bit */
+	tlbehi = SYSREG_BF(ASID, SYSREG_BFEXT(ASID, tlbehi));
+	sysreg_write(TLBEHI, tlbehi);
+
+	/* Mark it as "not accessed" */
+	tlbarlo = sysreg_read(TLBARLO);
+	sysreg_write(TLBARLO, tlbarlo | 0x80000000U);
+
+	/* Update the TLB */
+	__builtin_tlbw();
+
+	/* Unmask exceptions */
+	asm volatile("csrf	%0" : : "i"(SYSREG_EM_OFFSET) : "memory");
+}
+
+static int avr32_pm_valid_state(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		return 1;
+
+	default:
+		return 0;
+	}
+}
+
+static int avr32_pm_enter(suspend_state_t state)
+{
+	u32		lpr_saved;
+	u32		evba_saved;
+	void		*sram;
+
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		sram = avr32_pm_map_sram();
+
+		/* Switch to in-sram exception handlers */
+		evba_saved = sysreg_read(EVBA);
+		sysreg_write(EVBA, (unsigned long)sram);
+
+		/*
+		 * Save the LPR register so that we can re-enable
+		 * SDRAM Low Power mode on resume.
+		 */
+		lpr_saved = sdramc_readl(LPR);
+		pr_debug("%s: Entering standby...\n", __func__);
+		avr32_pm_enter_standby(SDRAMC_BASE);
+		sdramc_writel(LPR, lpr_saved);
+
+		/* Switch back to regular exception handlers */
+		sysreg_write(EVBA, evba_saved);
+
+		avr32_pm_unmap_sram();
+		break;
+
+	case PM_SUSPEND_MEM:
+		sram = avr32_pm_map_sram();
+
+		/* Switch to in-sram exception handlers */
+		evba_saved = sysreg_read(EVBA);
+		sysreg_write(EVBA, (unsigned long)sram);
+
+		/*
+		 * Save the LPR register so that we can re-enable
+		 * SDRAM Low Power mode on resume.
+		 */
+		lpr_saved = sdramc_readl(LPR);
+		pr_debug("%s: Entering suspend-to-ram...\n", __func__);
+		avr32_pm_enter_str(SDRAMC_BASE);
+		sdramc_writel(LPR, lpr_saved);
+
+		/* Switch back to regular exception handlers */
+		sysreg_write(EVBA, evba_saved);
+
+		avr32_pm_unmap_sram();
+		break;
+
+	case PM_SUSPEND_ON:
+		pr_debug("%s: Entering idle...\n", __func__);
+		cpu_enter_idle();
+		break;
+
+	default:
+		pr_debug("%s: Invalid suspend state %d\n", __func__, state);
+		goto out;
+	}
+
+	pr_debug("%s: wakeup\n", __func__);
+
+out:
+	return 0;
+}
+
+static struct platform_suspend_ops avr32_pm_ops = {
+	.valid	= avr32_pm_valid_state,
+	.enter	= avr32_pm_enter,
+};
+
+static unsigned long avr32_pm_offset(void *symbol)
+{
+	extern u8 pm_exception[];
+
+	return (unsigned long)symbol - (unsigned long)pm_exception;
+}
+
+static int __init avr32_pm_init(void)
+{
+	extern u8 pm_exception[];
+	extern u8 pm_irq0[];
+	extern u8 pm_standby[];
+	extern u8 pm_suspend_to_ram[];
+	extern u8 pm_sram_end[];
+	void *dst;
+
+	/*
+	 * To keep things simple, we depend on not needing more than a
+	 * single page.
+	 */
+	pm_sram_size = avr32_pm_offset(pm_sram_end);
+	if (pm_sram_size > PAGE_SIZE)
+		goto err;
+
+	pm_sram_start = sram_alloc(pm_sram_size);
+	if (!pm_sram_start)
+		goto err_alloc_sram;
+
+	/* Grab a virtual area we can use later on. */
+	pm_sram_area = get_vm_area(pm_sram_size, VM_IOREMAP);
+	if (!pm_sram_area)
+		goto err_vm_area;
+	pm_sram_area->phys_addr = pm_sram_start;
+
+	local_irq_disable();
+	dst = avr32_pm_map_sram();
+	memcpy(dst, pm_exception, pm_sram_size);
+	flush_dcache_region(dst, pm_sram_size);
+	invalidate_icache_region(dst, pm_sram_size);
+	avr32_pm_unmap_sram();
+	local_irq_enable();
+
+	avr32_pm_enter_standby = dst + avr32_pm_offset(pm_standby);
+	avr32_pm_enter_str = dst + avr32_pm_offset(pm_suspend_to_ram);
+	intc_set_suspend_handler(avr32_pm_offset(pm_irq0));
+
+	suspend_set_ops(&avr32_pm_ops);
+
+	printk("AVR32 AP Power Management enabled\n");
+
+	return 0;
+
+err_vm_area:
+	sram_free(pm_sram_start, pm_sram_size);
+err_alloc_sram:
+err:
+	pr_err("AVR32 Power Management initialization failed\n");
+	return -ENOMEM;
+}
+arch_initcall(avr32_pm_init);
diff --git a/arch/avr32/mach-at32ap/sdramc.h b/arch/avr32/mach-at32ap/sdramc.h
new file mode 100644
index 00000000000..66eeaed4907
--- /dev/null
+++ b/arch/avr32/mach-at32ap/sdramc.h
@@ -0,0 +1,76 @@
+/*
+ * Register definitions for the AT32AP SDRAM Controller
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+
+/* Register offsets */
+#define SDRAMC_MR			0x0000
+#define SDRAMC_TR			0x0004
+#define SDRAMC_CR			0x0008
+#define SDRAMC_HSR			0x000c
+#define SDRAMC_LPR			0x0010
+#define SDRAMC_IER			0x0014
+#define SDRAMC_IDR			0x0018
+#define SDRAMC_IMR			0x001c
+#define SDRAMC_ISR			0x0020
+#define SDRAMC_MDR			0x0024
+
+/* MR - Mode Register */
+#define SDRAMC_MR_MODE_NORMAL		(  0 <<  0)
+#define SDRAMC_MR_MODE_NOP		(  1 <<  0)
+#define SDRAMC_MR_MODE_BANKS_PRECHARGE	(  2 <<  0)
+#define SDRAMC_MR_MODE_LOAD_MODE	(  3 <<  0)
+#define SDRAMC_MR_MODE_AUTO_REFRESH	(  4 <<  0)
+#define SDRAMC_MR_MODE_EXT_LOAD_MODE	(  5 <<  0)
+#define SDRAMC_MR_MODE_POWER_DOWN	(  6 <<  0)
+
+/* CR - Configuration Register */
+#define SDRAMC_CR_NC_8_BITS		(  0 <<  0)
+#define SDRAMC_CR_NC_9_BITS		(  1 <<  0)
+#define SDRAMC_CR_NC_10_BITS		(  2 <<  0)
+#define SDRAMC_CR_NC_11_BITS		(  3 <<  0)
+#define SDRAMC_CR_NR_11_BITS		(  0 <<  2)
+#define SDRAMC_CR_NR_12_BITS		(  1 <<  2)
+#define SDRAMC_CR_NR_13_BITS		(  2 <<  2)
+#define SDRAMC_CR_NB_2_BANKS		(  0 <<  4)
+#define SDRAMC_CR_NB_4_BANKS		(  1 <<  4)
+#define SDRAMC_CR_CAS(x)		((x) <<  5)
+#define SDRAMC_CR_DBW_32_BITS		(  0 <<  7)
+#define SDRAMC_CR_DBW_16_BITS		(  1 <<  7)
+#define SDRAMC_CR_TWR(x)		((x) <<  8)
+#define SDRAMC_CR_TRC(x)		((x) << 12)
+#define SDRAMC_CR_TRP(x)		((x) << 16)
+#define SDRAMC_CR_TRCD(x)		((x) << 20)
+#define SDRAMC_CR_TRAS(x)		((x) << 24)
+#define SDRAMC_CR_TXSR(x)		((x) << 28)
+
+/* HSR - High Speed Register */
+#define SDRAMC_HSR_DA			(  1 <<  0)
+
+/* LPR - Low Power Register */
+#define SDRAMC_LPR_LPCB_INHIBIT		(  0 <<  0)
+#define SDRAMC_LPR_LPCB_SELF_RFR	(  1 <<  0)
+#define SDRAMC_LPR_LPCB_PDOWN		(  2 <<  0)
+#define SDRAMC_LPR_LPCB_DEEP_PDOWN	(  3 <<  0)
+#define SDRAMC_LPR_PASR(x)		((x) <<  4)
+#define SDRAMC_LPR_TCSR(x)		((x) <<  8)
+#define SDRAMC_LPR_DS(x)		((x) << 10)
+#define SDRAMC_LPR_TIMEOUT(x)		((x) << 12)
+
+/* IER/IDR/IMR/ISR - Interrupt Enable/Disable/Mask/Status Register */
+#define SDRAMC_ISR_RES			(  1 <<  0)
+
+/* MDR - Memory Device Register */
+#define SDRAMC_MDR_MD_SDRAM		(  0 <<  0)
+#define SDRAMC_MDR_MD_LOW_PWR_SDRAM	(  1 <<  0)
+
+/* Register access macros */
+#define sdramc_readl(reg) \
+	__raw_readl((void __iomem __force *)SDRAMC_BASE + SDRAMC_##reg)
+#define sdramc_writel(reg, value) \
+	__raw_writel(value, (void __iomem __force *)SDRAMC_BASE + SDRAMC_##reg)
-- 
cgit v1.2.3


From 72f6befeea7dc634a83219287d5b874734b85637 Mon Sep 17 00:00:00 2001
From: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Date: Fri, 4 Jul 2008 09:33:03 +0200
Subject: avr32: Fix typo of IFSR in a comment in the PIO header file

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/mach-at32ap/pio.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/pio.h b/arch/avr32/mach-at32ap/pio.h
index 7795116a483..9484dfcc08f 100644
--- a/arch/avr32/mach-at32ap/pio.h
+++ b/arch/avr32/mach-at32ap/pio.h
@@ -57,7 +57,7 @@
 
 /* Bitfields in IFDR */
 
-/* Bitfields in ISFR */
+/* Bitfields in IFSR */
 
 /* Bitfields in SODR */
 
-- 
cgit v1.2.3


From 3bfb1d20b547a5071d01344581eac5846ea84491 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Date: Tue, 8 Jul 2008 11:59:42 -0700
Subject: dmaengine: Driver for the Synopsys DesignWare DMA controller

This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.

This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.

The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.

Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:

http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf

The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682


Changes since v4:
  * Use client_count instead of dma_chan_is_in_use()
  * Add missing include
  * Unmap buffers unless client told us not to

Changes since v3:
  * Update to latest DMA engine and DMA slave APIs
  * Embed the hw descriptor into the sw descriptor
  * Clean up and update MODULE_DESCRIPTION, copyright date, etc.

Changes since v2:
  * Dequeue all pending transfers in terminate_all()
  * Rename dw_dmac.h -> dw_dmac_regs.h
  * Define and use controller-specific dma_slave data
  * Fix up a few outdated comments
  * Define hardware registers as structs (doesn't generate better
    code, unfortunately, but it looks nicer.)
  * Get number of channels from platform_data instead of hardcoding it
    based on CONFIG_WHATEVER_CPU.
  * Give slave clients exclusive access to the channel

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 27 ++++++++++++++-------------
 1 file changed, 14 insertions(+), 13 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 0f24b4f85c1..892e27e0d58 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -7,6 +7,7 @@
  */
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dw_dmac.h>
 #include <linux/fb.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -599,6 +600,17 @@ static void __init genclk_init_parent(struct clk *clk)
 	clk->parent = parent;
 }
 
+static struct dw_dma_platform_data dw_dmac0_data = {
+	.nr_channels	= 3,
+};
+
+static struct resource dw_dmac0_resource[] = {
+	PBMEM(0xff200000),
+	IRQ(2),
+};
+DEFINE_DEV_DATA(dw_dmac, 0);
+DEV_CLK(hclk, dw_dmac0, hsb, 10);
+
 /* --------------------------------------------------------------------
  *  System peripherals
  * -------------------------------------------------------------------- */
@@ -705,17 +717,6 @@ static struct clk pico_clk = {
 	.users		= 1,
 };
 
-static struct resource dmaca0_resource[] = {
-	{
-		.start	= 0xff200000,
-		.end	= 0xff20ffff,
-		.flags	= IORESOURCE_MEM,
-	},
-	IRQ(2),
-};
-DEFINE_DEV(dmaca, 0);
-DEV_CLK(hclk, dmaca0, hsb, 10);
-
 /* --------------------------------------------------------------------
  * HMATRIX
  * -------------------------------------------------------------------- */
@@ -828,7 +829,7 @@ void __init at32_add_system_devices(void)
 	platform_device_register(&at32_eic0_device);
 	platform_device_register(&smc0_device);
 	platform_device_register(&pdc_device);
-	platform_device_register(&dmaca0_device);
+	platform_device_register(&dw_dmac0_device);
 
 	platform_device_register(&at32_tcb0_device);
 	platform_device_register(&at32_tcb1_device);
@@ -1891,7 +1892,7 @@ struct clk *at32_clock_list[] = {
 	&smc0_mck,
 	&pdc_hclk,
 	&pdc_pclk,
-	&dmaca0_hclk,
+	&dw_dmac0_hclk,
 	&pico_clk,
 	&pio0_mck,
 	&pio1_mck,
-- 
cgit v1.2.3


From 7d2be0749a59096a334c94dc48f43294193cb8ed Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Date: Mon, 30 Jun 2008 18:35:03 +0200
Subject: atmel-mci: Driver for Atmel on-chip MMC controllers

This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.

This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.

This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)

Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.

The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.

The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.

Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
---
 arch/avr32/mach-at32ap/at32ap700x.c | 30 +++++++++++++++++++++++++-----
 1 file changed, 25 insertions(+), 5 deletions(-)

(limited to 'arch/avr32/mach-at32ap')

diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 07b21b121ee..021d5121718 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -14,6 +14,7 @@
 #include <linux/spi/spi.h>
 #include <linux/usb/atmel_usba_udc.h>
 
+#include <asm/atmel-mci.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 
@@ -1278,20 +1279,32 @@ static struct clk atmel_mci0_pclk = {
 	.index		= 9,
 };
 
-struct platform_device *__init at32_add_device_mci(unsigned int id)
+struct platform_device *__init
+at32_add_device_mci(unsigned int id, struct mci_platform_data *data)
 {
-	struct platform_device *pdev;
+	struct mci_platform_data	_data;
+	struct platform_device		*pdev;
+	struct dw_dma_slave		*dws;
 
 	if (id != 0)
 		return NULL;
 
 	pdev = platform_device_alloc("atmel_mci", id);
 	if (!pdev)
-		return NULL;
+		goto fail;
 
 	if (platform_device_add_resources(pdev, atmel_mci0_resource,
 				ARRAY_SIZE(atmel_mci0_resource)))
-		goto err_add_resources;
+		goto fail;
+
+	if (!data) {
+		data = &_data;
+		memset(data, 0, sizeof(struct mci_platform_data));
+	}
+
+	if (platform_device_add_data(pdev, data,
+				sizeof(struct mci_platform_data)))
+		goto fail;
 
 	select_peripheral(PA(10), PERIPH_A, 0);	/* CLK	 */
 	select_peripheral(PA(11), PERIPH_A, 0);	/* CMD	 */
@@ -1300,12 +1313,19 @@ struct platform_device *__init at32_add_device_mci(unsigned int id)
 	select_peripheral(PA(14), PERIPH_A, 0);	/* DATA2 */
 	select_peripheral(PA(15), PERIPH_A, 0);	/* DATA3 */
 
+	if (data) {
+		if (data->detect_pin != GPIO_PIN_NONE)
+			at32_select_gpio(data->detect_pin, 0);
+		if (data->wp_pin != GPIO_PIN_NONE)
+			at32_select_gpio(data->wp_pin, 0);
+	}
+
 	atmel_mci0_pclk.dev = &pdev->dev;
 
 	platform_device_add(pdev);
 	return pdev;
 
-err_add_resources:
+fail:
 	platform_device_put(pdev);
 	return NULL;
 }
-- 
cgit v1.2.3