From 275f55170ec2b5d777b070cb8ab9e5d58e65a2a8 Mon Sep 17 00:00:00 2001 From: Vivek Goyal Date: Wed, 2 May 2007 19:27:07 +0200 Subject: [PATCH] x86-64: wakeup.S misc cleanups o Various cleanups. One of the main purpose of cleanups is that make wakeup.S as close as possible to trampoline.S. o Following are the changes - Indentations for comments. - Changed the gdt table to compact form and to resemble the one in trampoline.S - Take the jump to 32bit from real mode using ljmpl. Makes code more readable. - After enabling long mode, directly take a long jump for 64bit mode. No need to take an extra jump to "reach_comaptibility_mode" - Stack is not used after real mode. So don't load stack in 32 bit mode. - No need to enable PGE here. - No need to do extra EFER read, anyway we trash the read contents. - No need to enable system call (EFER_SCE). Anyway it will be enabled when original EFER is restored. - No need to set MP, ET, NE, WP, AM bits in cr0. Very soon we will reload the original cr0 while restroing the processor state. Signed-off-by: Eric W. Biederman Signed-off-by: Vivek Goyal Signed-off-by: Andi Kleen --- arch/x86_64/kernel/acpi/wakeup.S | 112 ++++++++++++++------------------------- 1 file changed, 40 insertions(+), 72 deletions(-) (limited to 'arch') diff --git a/arch/x86_64/kernel/acpi/wakeup.S b/arch/x86_64/kernel/acpi/wakeup.S index 17dbeff64ee..bd4c6f1a6f3 100644 --- a/arch/x86_64/kernel/acpi/wakeup.S +++ b/arch/x86_64/kernel/acpi/wakeup.S @@ -30,11 +30,12 @@ wakeup_code: cld # setup data segment movw %cs, %ax - movw %ax, %ds # Make ds:0 point to wakeup_start + movw %ax, %ds # Make ds:0 point to wakeup_start movw %ax, %ss - mov $(wakeup_stack - wakeup_code), %sp # Private stack is needed for ASUS board + # Private stack is needed for ASUS board + mov $(wakeup_stack - wakeup_code), %sp - pushl $0 # Kill any dangerous flags + pushl $0 # Kill any dangerous flags popfl movl real_magic - wakeup_code, %eax @@ -45,7 +46,7 @@ wakeup_code: jz 1f lcall $0xc000,$3 movw %cs, %ax - movw %ax, %ds # Bios might have played with that + movw %ax, %ds # Bios might have played with that movw %ax, %ss 1: @@ -75,9 +76,12 @@ wakeup_code: jmp 1f 1: - .byte 0x66, 0xea # prefix + jmpi-opcode - .long wakeup_32 - __START_KERNEL_map - .word __KERNEL_CS + ljmpl *(wakeup_32_vector - wakeup_code) + + .balign 4 +wakeup_32_vector: + .long wakeup_32 - __START_KERNEL_map + .word __KERNEL32_CS, 0 .code32 wakeup_32: @@ -96,65 +100,50 @@ wakeup_32: jnc bogus_cpu movl %edx,%edi - movw $__KERNEL_DS, %ax - movw %ax, %ds - movw %ax, %es - movw %ax, %fs - movw %ax, %gs + movl $__KERNEL_DS, %eax + movl %eax, %ds - movw $__KERNEL_DS, %ax - movw %ax, %ss - - mov $(wakeup_stack - __START_KERNEL_map), %esp movl saved_magic - __START_KERNEL_map, %eax cmpl $0x9abcdef0, %eax jne bogus_32_magic + movw $0x0e00 + 'i', %ds:(0xb8012) + movb $0xa8, %al ; outb %al, $0x80; + /* * Prepare for entering 64bits mode */ - /* Enable PAE mode and PGE */ + /* Enable PAE */ xorl %eax, %eax btsl $5, %eax - btsl $7, %eax movl %eax, %cr4 /* Setup early boot stage 4 level pagetables */ movl $(wakeup_level4_pgt - __START_KERNEL_map), %eax movl %eax, %cr3 - /* Setup EFER (Extended Feature Enable Register) */ - movl $MSR_EFER, %ecx - rdmsr - /* Fool rdmsr and reset %eax to avoid dependences */ - xorl %eax, %eax /* Enable Long Mode */ + xorl %eax, %eax btsl $_EFER_LME, %eax - /* Enable System Call */ - btsl $_EFER_SCE, %eax - /* No Execute supported? */ + /* No Execute supported? */ btl $20,%edi jnc 1f btsl $_EFER_NX, %eax -1: /* Make changes effective */ +1: movl $MSR_EFER, %ecx + xorl %edx, %edx wrmsr - wbinvd xorl %eax, %eax btsl $31, %eax /* Enable paging and in turn activate Long Mode */ btsl $0, %eax /* Enable protected mode */ - btsl $1, %eax /* Enable MP */ - btsl $4, %eax /* Enable ET */ - btsl $5, %eax /* Enable NE */ - btsl $16, %eax /* Enable WP */ - btsl $18, %eax /* Enable AM */ /* Make changes effective */ movl %eax, %cr0 + /* At this point: CR4.PAE must be 1 CS.L must be 0 @@ -162,11 +151,6 @@ wakeup_32: Next instruction must be a branch This must be on identity-mapped page */ - jmp reach_compatibility_mode -reach_compatibility_mode: - movw $0x0e00 + 'i', %ds:(0xb8012) - movb $0xa8, %al ; outb %al, $0x80; - /* * At this point we're in long mode but in 32bit compatibility mode * with EFER.LME = 1, CS.L = 0, CS.D = 1 (and in turn @@ -174,24 +158,19 @@ reach_compatibility_mode: * the new gdt/idt that has __KERNEL_CS with CS.L = 1. */ - movw $0x0e00 + 'n', %ds:(0xb8014) - movb $0xa9, %al ; outb %al, $0x80 - - /* Load new GDT with the 64bit segment using 32bit descriptor */ - movl $(pGDT32 - __START_KERNEL_map), %eax - lgdt (%eax) - - movl $(wakeup_jumpvector - __START_KERNEL_map), %eax /* Finally jump in 64bit mode */ - ljmp *(%eax) + ljmp *(wakeup_long64_vector - __START_KERNEL_map) -wakeup_jumpvector: - .long wakeup_long64 - __START_KERNEL_map - .word __KERNEL_CS + .balign 4 +wakeup_long64_vector: + .long wakeup_long64 - __START_KERNEL_map + .word __KERNEL_CS, 0 .code64 - /* Hooray, we are in Long 64-bit mode (but still running in low memory) */ + /* Hooray, we are in Long 64-bit mode (but still running in + * low memory) + */ wakeup_long64: /* * We must switch to a new descriptor in kernel space for the GDT @@ -201,6 +180,9 @@ wakeup_long64: */ lgdt cpu_gdt_descr - __START_KERNEL_map + movw $0x0e00 + 'n', %ds:(0xb8014) + movb $0xa9, %al ; outb %al, $0x80 + movw $0x0e00 + 'u', %ds:(0xb8016) nop @@ -227,33 +209,19 @@ wakeup_long64: .align 64 gdta: + /* Its good to keep gdt in sync with one in trampoline.S */ .word 0, 0, 0, 0 # dummy - - .word 0, 0, 0, 0 # unused - - .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb) - .word 0 # base address = 0 - .word 0x9B00 # code read/exec. ??? Why I need 0x9B00 (as opposed to 0x9A00 in order for this to work?) - .word 0x00CF # granularity = 4096, 386 - # (+5th nibble of limit) - - .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb) - .word 0 # base address = 0 - .word 0x9200 # data read/write - .word 0x00CF # granularity = 4096, 386 - # (+5th nibble of limit) -# this is 64bit descriptor for code - .word 0xFFFF - .word 0 - .word 0x9A00 # code read/exec - .word 0x00AF # as above, but it is long mode and with D=0 + /* ??? Why I need the accessed bit set in order for this to work? */ + .quad 0x00cf9b000000ffff # __KERNEL32_CS + .quad 0x00af9b000000ffff # __KERNEL_CS + .quad 0x00cf93000000ffff # __KERNEL_DS idt_48a: .word 0 # idt limit = 0 .word 0, 0 # idt base = 0L gdt_48a: - .word 0x8000 # gdt limit=2048, + .word 0x800 # gdt limit=2048, # 256 GDT entries .word 0, 0 # gdt base (filled in later) @@ -263,7 +231,7 @@ video_mode: .quad 0 video_flags: .quad 0 bogus_real_magic: - movb $0xba,%al ; outb %al,$0x80 + movb $0xba,%al ; outb %al,$0x80 jmp bogus_real_magic bogus_32_magic: -- cgit v1.2.3