From ba0acb5ee318901646f82c134cca2e4de0c43934 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Mon, 7 May 2007 17:31:32 -0400 Subject: Input: move USB miscellaneous devices under drivers/input/misc This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov Acked-by: Greg Kroah-Hartman --- drivers/input/misc/Kconfig | 88 ++- drivers/input/misc/Makefile | 9 +- drivers/input/misc/ati_remote.c | 862 +++++++++++++++++++++++++++++ drivers/input/misc/ati_remote2.c | 543 ++++++++++++++++++ drivers/input/misc/keyspan_remote.c | 592 ++++++++++++++++++++ drivers/input/misc/map_to_7segment.h | 189 +++++++ drivers/input/misc/powermate.c | 463 ++++++++++++++++ drivers/input/misc/yealink.c | 1004 ++++++++++++++++++++++++++++++++++ drivers/input/misc/yealink.h | 220 ++++++++ 9 files changed, 3961 insertions(+), 9 deletions(-) create mode 100644 drivers/input/misc/ati_remote.c create mode 100644 drivers/input/misc/ati_remote2.c create mode 100644 drivers/input/misc/keyspan_remote.c create mode 100644 drivers/input/misc/map_to_7segment.h create mode 100644 drivers/input/misc/powermate.c create mode 100644 drivers/input/misc/yealink.c create mode 100644 drivers/input/misc/yealink.h (limited to 'drivers/input') diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 1d0d3e765db..6013ace94d9 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -40,6 +40,18 @@ config INPUT_M68K_BEEP tristate "M68k Beeper support" depends on M68K +config INPUT_IXP4XX_BEEPER + tristate "IXP4XX Beeper support" + depends on ARCH_IXP4XX + help + If you say yes here, you can connect a beeper to the + ixp4xx gpio pins. This is used by the LinkSys NSLU2. + + If unsure, say Y. + + To compile this driver as a module, choose M here: the + module will be called ixp4xx-beeper. + config INPUT_COBALT_BTNS tristate "Cobalt button interface" depends on MIPS_COBALT @@ -70,17 +82,79 @@ config INPUT_ATLAS_BTNS To compile this driver as a module, choose M here: the module will be called atlas_btns. -config INPUT_IXP4XX_BEEPER - tristate "IXP4XX Beeper support" - depends on ARCH_IXP4XX +config INPUT_ATI_REMOTE + tristate "ATI / X10 USB RF remote control" + select USB help - If you say yes here, you can connect a beeper to the - ixp4xx gpio pins. This is used by the LinkSys NSLU2. + Say Y here if you want to use an ATI or X10 "Lola" USB remote control. + These are RF remotes with USB receivers. + The ATI remote comes with many of ATI's All-In-Wonder video cards. + The X10 "Lola" remote is available at: + + This driver provides mouse pointer, left and right mouse buttons, + and maps all the other remote buttons to keypress events. + + To compile this driver as a module, choose M here: the module will be + called ati_remote. + +config INPUT_ATI_REMOTE2 + tristate "ATI / Philips USB RF remote control" + select USB + help + Say Y here if you want to use an ATI or Philips USB RF remote control. + These are RF remotes with USB receivers. + ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards + and is also available as a separate product. + This driver provides mouse pointer, left and right mouse buttons, + and maps all the other remote buttons to keypress events. + + To compile this driver as a module, choose M here: the module will be + called ati_remote2. + +config INPUT_KEYSPAN_REMOTE + tristate "Keyspan DMR USB remote control (EXPERIMENTAL)" + depends on EXPERIMENTAL + select USB + help + Say Y here if you want to use a Keyspan DMR USB remote control. + Currently only the UIA-11 type of receiver has been tested. The tag + on the receiver that connects to the USB port should have a P/N that + will tell you what type of DMR you have. The UIA-10 type is not + supported at this time. This driver maps all buttons to keypress + events. - If unsure, say Y. + To compile this driver as a module, choose M here: the module will + be called keyspan_remote. + +config INPUT_POWERMATE + tristate "Griffin PowerMate and Contour Jog support" + select USB + help + Say Y here if you want to use Griffin PowerMate or Contour Jog devices. + These are aluminum dials which can measure clockwise and anticlockwise + rotation. The dial also acts as a pushbutton. The base contains an LED + which can be instructed to pulse or to switch to a particular intensity. + + You can download userspace tools from + . To compile this driver as a module, choose M here: the - module will be called ixp4xx-beeper. + module will be called powermate. + +config INPUT_YEALINK + tristate "Yealink usb-p1k voip phone" + depends EXPERIMENTAL + select USB + help + Say Y here if you want to enable keyboard and LCD functions of the + Yealink usb-p1k usb phones. The audio part is enabled by the generic + usb sound driver, so you might want to enable that as well. + + For information about how to use these additional functions, see + . + + To compile this driver as a module, choose M here: the module will be + called yealink. config INPUT_UINPUT tristate "User level driver support" diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index 21e3cca0d33..8b2f7799e25 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -8,9 +8,14 @@ obj-$(CONFIG_INPUT_POLLDEV) += input-polldev.o obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_PCSPKR) += pcspkr.o obj-$(CONFIG_INPUT_M68K_BEEP) += m68kspkr.o -obj-$(CONFIG_INPUT_UINPUT) += uinput.o +obj-$(CONFIG_INPUT_IXP4XX_BEEPER) += ixp4xx-beeper.o obj-$(CONFIG_INPUT_COBALT_BTNS) += cobalt_btns.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_ATLAS_BTNS) += atlas_btns.o +obj-$(CONFIG_INPUT_ATI_REMOTE) += ati_remote.o +obj-$(CONFIG_INPUT_ATI_REMOTE2) += ati_remote2.o +obj-$(CONFIG_INPUT_KEYSPAN_REMOTE) += keyspan_remote.o +obj-$(CONFIG_INPUT_POWERMATE) += powermate.o +obj-$(CONFIG_INPUT_YEALINK) += yealink.o obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o -obj-$(CONFIG_INPUT_IXP4XX_BEEPER) += ixp4xx-beeper.o +obj-$(CONFIG_INPUT_UINPUT) += uinput.o diff --git a/drivers/input/misc/ati_remote.c b/drivers/input/misc/ati_remote.c new file mode 100644 index 00000000000..471aab20644 --- /dev/null +++ b/drivers/input/misc/ati_remote.c @@ -0,0 +1,862 @@ +/* + * USB ATI Remote support + * + * Version 2.2.0 Copyright (c) 2004 Torrey Hoffman + * Version 2.1.1 Copyright (c) 2002 Vladimir Dergachev + * + * This 2.2.0 version is a rewrite / cleanup of the 2.1.1 driver, including + * porting to the 2.6 kernel interfaces, along with other modification + * to better match the style of the existing usb/input drivers. However, the + * protocol and hardware handling is essentially unchanged from 2.1.1. + * + * The 2.1.1 driver was derived from the usbati_remote and usbkbd drivers by + * Vojtech Pavlik. + * + * Changes: + * + * Feb 2004: Torrey Hoffman + * Version 2.2.0 + * Jun 2004: Torrey Hoffman + * Version 2.2.1 + * Added key repeat support contributed by: + * Vincent Vanackere + * Added support for the "Lola" remote contributed by: + * Seth Cohn + * + * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * + * + * Hardware & software notes + * + * These remote controls are distributed by ATI as part of their + * "All-In-Wonder" video card packages. The receiver self-identifies as a + * "USB Receiver" with manufacturer "X10 Wireless Technology Inc". + * + * The "Lola" remote is available from X10. See: + * http://www.x10.com/products/lola_sg1.htm + * The Lola is similar to the ATI remote but has no mouse support, and slightly + * different keys. + * + * It is possible to use multiple receivers and remotes on multiple computers + * simultaneously by configuring them to use specific channels. + * + * The RF protocol used by the remote supports 16 distinct channels, 1 to 16. + * Actually, it may even support more, at least in some revisions of the + * hardware. + * + * Each remote can be configured to transmit on one channel as follows: + * - Press and hold the "hand icon" button. + * - When the red LED starts to blink, let go of the "hand icon" button. + * - When it stops blinking, input the channel code as two digits, from 01 + * to 16, and press the hand icon again. + * + * The timing can be a little tricky. Try loading the module with debug=1 + * to have the kernel print out messages about the remote control number + * and mask. Note: debugging prints remote numbers as zero-based hexadecimal. + * + * The driver has a "channel_mask" parameter. This bitmask specifies which + * channels will be ignored by the module. To mask out channels, just add + * all the 2^channel_number values together. + * + * For instance, set channel_mask = 2^4 = 16 (binary 10000) to make ati_remote + * ignore signals coming from remote controls transmitting on channel 4, but + * accept all other channels. + * + * Or, set channel_mask = 65533, (0xFFFD), and all channels except 1 will be + * ignored. + * + * The default is 0 (respond to all channels). Bit 0 and bits 17-32 of this + * parameter are unused. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * Module and Version Information, Module Parameters + */ + +#define ATI_REMOTE_VENDOR_ID 0x0bc7 +#define ATI_REMOTE_PRODUCT_ID 0x004 +#define LOLA_REMOTE_PRODUCT_ID 0x002 +#define MEDION_REMOTE_PRODUCT_ID 0x006 + +#define DRIVER_VERSION "2.2.1" +#define DRIVER_AUTHOR "Torrey Hoffman " +#define DRIVER_DESC "ATI/X10 RF USB Remote Control" + +#define NAME_BUFSIZE 80 /* size of product name, path buffers */ +#define DATA_BUFSIZE 63 /* size of URB data buffers */ + +/* + * Duplicate event filtering time. + * Sequential, identical KIND_FILTERED inputs with less than + * FILTER_TIME milliseconds between them are considered as repeat + * events. The hardware generates 5 events for the first keypress + * and we have to take this into account for an accurate repeat + * behaviour. + */ +#define FILTER_TIME 60 /* msec */ +#define REPEAT_DELAY 500 /* msec */ + +static unsigned long channel_mask; +module_param(channel_mask, ulong, 0644); +MODULE_PARM_DESC(channel_mask, "Bitmask of remote control channels to ignore"); + +static int debug; +module_param(debug, int, 0644); +MODULE_PARM_DESC(debug, "Enable extra debug messages and information"); + +static int repeat_filter = FILTER_TIME; +module_param(repeat_filter, int, 0644); +MODULE_PARM_DESC(repeat_filter, "Repeat filter time, default = 60 msec"); + +static int repeat_delay = REPEAT_DELAY; +module_param(repeat_delay, int, 0644); +MODULE_PARM_DESC(repeat_delay, "Delay before sending repeats, default = 500 msec"); + +#define dbginfo(dev, format, arg...) do { if (debug) dev_info(dev , format , ## arg); } while (0) +#undef err +#define err(format, arg...) printk(KERN_ERR format , ## arg) + +static struct usb_device_id ati_remote_table[] = { + { USB_DEVICE(ATI_REMOTE_VENDOR_ID, ATI_REMOTE_PRODUCT_ID) }, + { USB_DEVICE(ATI_REMOTE_VENDOR_ID, LOLA_REMOTE_PRODUCT_ID) }, + { USB_DEVICE(ATI_REMOTE_VENDOR_ID, MEDION_REMOTE_PRODUCT_ID) }, + {} /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(usb, ati_remote_table); + +/* Get hi and low bytes of a 16-bits int */ +#define HI(a) ((unsigned char)((a) >> 8)) +#define LO(a) ((unsigned char)((a) & 0xff)) + +#define SEND_FLAG_IN_PROGRESS 1 +#define SEND_FLAG_COMPLETE 2 + +/* Device initialization strings */ +static char init1[] = { 0x01, 0x00, 0x20, 0x14 }; +static char init2[] = { 0x01, 0x00, 0x20, 0x14, 0x20, 0x20, 0x20 }; + +struct ati_remote { + struct input_dev *idev; + struct usb_device *udev; + struct usb_interface *interface; + + struct urb *irq_urb; + struct urb *out_urb; + struct usb_endpoint_descriptor *endpoint_in; + struct usb_endpoint_descriptor *endpoint_out; + unsigned char *inbuf; + unsigned char *outbuf; + dma_addr_t inbuf_dma; + dma_addr_t outbuf_dma; + + unsigned char old_data[2]; /* Detect duplicate events */ + unsigned long old_jiffies; + unsigned long acc_jiffies; /* handle acceleration */ + unsigned long first_jiffies; + + unsigned int repeat_count; + + char name[NAME_BUFSIZE]; + char phys[NAME_BUFSIZE]; + + wait_queue_head_t wait; + int send_flags; +}; + +/* "Kinds" of messages sent from the hardware to the driver. */ +#define KIND_END 0 +#define KIND_LITERAL 1 /* Simply pass to input system */ +#define KIND_FILTERED 2 /* Add artificial key-up events, drop keyrepeats */ +#define KIND_LU 3 /* Directional keypad diagonals - left up, */ +#define KIND_RU 4 /* right up, */ +#define KIND_LD 5 /* left down, */ +#define KIND_RD 6 /* right down */ +#define KIND_ACCEL 7 /* Directional keypad - left, right, up, down.*/ + +/* Translation table from hardware messages to input events. */ +static const struct { + short kind; + unsigned char data1, data2; + int type; + unsigned int code; + int value; +} ati_remote_tbl[] = { + /* Directional control pad axes */ + {KIND_ACCEL, 0x35, 0x70, EV_REL, REL_X, -1}, /* left */ + {KIND_ACCEL, 0x36, 0x71, EV_REL, REL_X, 1}, /* right */ + {KIND_ACCEL, 0x37, 0x72, EV_REL, REL_Y, -1}, /* up */ + {KIND_ACCEL, 0x38, 0x73, EV_REL, REL_Y, 1}, /* down */ + /* Directional control pad diagonals */ + {KIND_LU, 0x39, 0x74, EV_REL, 0, 0}, /* left up */ + {KIND_RU, 0x3a, 0x75, EV_REL, 0, 0}, /* right up */ + {KIND_LD, 0x3c, 0x77, EV_REL, 0, 0}, /* left down */ + {KIND_RD, 0x3b, 0x76, EV_REL, 0, 0}, /* right down */ + + /* "Mouse button" buttons */ + {KIND_LITERAL, 0x3d, 0x78, EV_KEY, BTN_LEFT, 1}, /* left btn down */ + {KIND_LITERAL, 0x3e, 0x79, EV_KEY, BTN_LEFT, 0}, /* left btn up */ + {KIND_LITERAL, 0x41, 0x7c, EV_KEY, BTN_RIGHT, 1},/* right btn down */ + {KIND_LITERAL, 0x42, 0x7d, EV_KEY, BTN_RIGHT, 0},/* right btn up */ + + /* Artificial "doubleclick" events are generated by the hardware. + * They are mapped to the "side" and "extra" mouse buttons here. */ + {KIND_FILTERED, 0x3f, 0x7a, EV_KEY, BTN_SIDE, 1}, /* left dblclick */ + {KIND_FILTERED, 0x43, 0x7e, EV_KEY, BTN_EXTRA, 1},/* right dblclick */ + + /* keyboard. */ + {KIND_FILTERED, 0xd2, 0x0d, EV_KEY, KEY_1, 1}, + {KIND_FILTERED, 0xd3, 0x0e, EV_KEY, KEY_2, 1}, + {KIND_FILTERED, 0xd4, 0x0f, EV_KEY, KEY_3, 1}, + {KIND_FILTERED, 0xd5, 0x10, EV_KEY, KEY_4, 1}, + {KIND_FILTERED, 0xd6, 0x11, EV_KEY, KEY_5, 1}, + {KIND_FILTERED, 0xd7, 0x12, EV_KEY, KEY_6, 1}, + {KIND_FILTERED, 0xd8, 0x13, EV_KEY, KEY_7, 1}, + {KIND_FILTERED, 0xd9, 0x14, EV_KEY, KEY_8, 1}, + {KIND_FILTERED, 0xda, 0x15, EV_KEY, KEY_9, 1}, + {KIND_FILTERED, 0xdc, 0x17, EV_KEY, KEY_0, 1}, + {KIND_FILTERED, 0xc5, 0x00, EV_KEY, KEY_A, 1}, + {KIND_FILTERED, 0xc6, 0x01, EV_KEY, KEY_B, 1}, + {KIND_FILTERED, 0xde, 0x19, EV_KEY, KEY_C, 1}, + {KIND_FILTERED, 0xe0, 0x1b, EV_KEY, KEY_D, 1}, + {KIND_FILTERED, 0xe6, 0x21, EV_KEY, KEY_E, 1}, + {KIND_FILTERED, 0xe8, 0x23, EV_KEY, KEY_F, 1}, + + /* "special" keys */ + {KIND_FILTERED, 0xdd, 0x18, EV_KEY, KEY_KPENTER, 1}, /* "check" */ + {KIND_FILTERED, 0xdb, 0x16, EV_KEY, KEY_MENU, 1}, /* "menu" */ + {KIND_FILTERED, 0xc7, 0x02, EV_KEY, KEY_POWER, 1}, /* Power */ + {KIND_FILTERED, 0xc8, 0x03, EV_KEY, KEY_TV, 1}, /* TV */ + {KIND_FILTERED, 0xc9, 0x04, EV_KEY, KEY_DVD, 1}, /* DVD */ + {KIND_FILTERED, 0xca, 0x05, EV_KEY, KEY_WWW, 1}, /* WEB */ + {KIND_FILTERED, 0xcb, 0x06, EV_KEY, KEY_BOOKMARKS, 1}, /* "book" */ + {KIND_FILTERED, 0xcc, 0x07, EV_KEY, KEY_EDIT, 1}, /* "hand" */ + {KIND_FILTERED, 0xe1, 0x1c, EV_KEY, KEY_COFFEE, 1}, /* "timer" */ + {KIND_FILTERED, 0xe5, 0x20, EV_KEY, KEY_FRONT, 1}, /* "max" */ + {KIND_FILTERED, 0xe2, 0x1d, EV_KEY, KEY_LEFT, 1}, /* left */ + {KIND_FILTERED, 0xe4, 0x1f, EV_KEY, KEY_RIGHT, 1}, /* right */ + {KIND_FILTERED, 0xe7, 0x22, EV_KEY, KEY_DOWN, 1}, /* down */ + {KIND_FILTERED, 0xdf, 0x1a, EV_KEY, KEY_UP, 1}, /* up */ + {KIND_FILTERED, 0xe3, 0x1e, EV_KEY, KEY_OK, 1}, /* "OK" */ + {KIND_FILTERED, 0xce, 0x09, EV_KEY, KEY_VOLUMEDOWN, 1}, /* VOL + */ + {KIND_FILTERED, 0xcd, 0x08, EV_KEY, KEY_VOLUMEUP, 1}, /* VOL - */ + {KIND_FILTERED, 0xcf, 0x0a, EV_KEY, KEY_MUTE, 1}, /* MUTE */ + {KIND_FILTERED, 0xd0, 0x0b, EV_KEY, KEY_CHANNELUP, 1}, /* CH + */ + {KIND_FILTERED, 0xd1, 0x0c, EV_KEY, KEY_CHANNELDOWN, 1},/* CH - */ + {KIND_FILTERED, 0xec, 0x27, EV_KEY, KEY_RECORD, 1}, /* ( o) red */ + {KIND_FILTERED, 0xea, 0x25, EV_KEY, KEY_PLAY, 1}, /* ( >) */ + {KIND_FILTERED, 0xe9, 0x24, EV_KEY, KEY_REWIND, 1}, /* (<<) */ + {KIND_FILTERED, 0xeb, 0x26, EV_KEY, KEY_FORWARD, 1}, /* (>>) */ + {KIND_FILTERED, 0xed, 0x28, EV_KEY, KEY_STOP, 1}, /* ([]) */ + {KIND_FILTERED, 0xee, 0x29, EV_KEY, KEY_PAUSE, 1}, /* ('') */ + {KIND_FILTERED, 0xf0, 0x2b, EV_KEY, KEY_PREVIOUS, 1}, /* (<-) */ + {KIND_FILTERED, 0xef, 0x2a, EV_KEY, KEY_NEXT, 1}, /* (>+) */ + {KIND_FILTERED, 0xf2, 0x2D, EV_KEY, KEY_INFO, 1}, /* PLAYING */ + {KIND_FILTERED, 0xf3, 0x2E, EV_KEY, KEY_HOME, 1}, /* TOP */ + {KIND_FILTERED, 0xf4, 0x2F, EV_KEY, KEY_END, 1}, /* END */ + {KIND_FILTERED, 0xf5, 0x30, EV_KEY, KEY_SELECT, 1}, /* SELECT */ + + {KIND_END, 0x00, 0x00, EV_MAX + 1, 0, 0} +}; + +/* Local function prototypes */ +static void ati_remote_dump (unsigned char *data, unsigned int actual_length); +static int ati_remote_open (struct input_dev *inputdev); +static void ati_remote_close (struct input_dev *inputdev); +static int ati_remote_sendpacket (struct ati_remote *ati_remote, u16 cmd, unsigned char *data); +static void ati_remote_irq_out (struct urb *urb); +static void ati_remote_irq_in (struct urb *urb); +static void ati_remote_input_report (struct urb *urb); +static int ati_remote_initialize (struct ati_remote *ati_remote); +static int ati_remote_probe (struct usb_interface *interface, const struct usb_device_id *id); +static void ati_remote_disconnect (struct usb_interface *interface); + +/* usb specific object to register with the usb subsystem */ +static struct usb_driver ati_remote_driver = { + .name = "ati_remote", + .probe = ati_remote_probe, + .disconnect = ati_remote_disconnect, + .id_table = ati_remote_table, +}; + +/* + * ati_remote_dump_input + */ +static void ati_remote_dump(unsigned char *data, unsigned int len) +{ + if ((len == 1) && (data[0] != (unsigned char)0xff) && (data[0] != 0x00)) + warn("Weird byte 0x%02x", data[0]); + else if (len == 4) + warn("Weird key %02x %02x %02x %02x", + data[0], data[1], data[2], data[3]); + else + warn("Weird data, len=%d %02x %02x %02x %02x %02x %02x ...", + len, data[0], data[1], data[2], data[3], data[4], data[5]); +} + +/* + * ati_remote_open + */ +static int ati_remote_open(struct input_dev *inputdev) +{ + struct ati_remote *ati_remote = input_get_drvdata(inputdev); + + /* On first open, submit the read urb which was set up previously. */ + ati_remote->irq_urb->dev = ati_remote->udev; + if (usb_submit_urb(ati_remote->irq_urb, GFP_KERNEL)) { + dev_err(&ati_remote->interface->dev, + "%s: usb_submit_urb failed!\n", __FUNCTION__); + return -EIO; + } + + return 0; +} + +/* + * ati_remote_close + */ +static void ati_remote_close(struct input_dev *inputdev) +{ + struct ati_remote *ati_remote = input_get_drvdata(inputdev); + + usb_kill_urb(ati_remote->irq_urb); +} + +/* + * ati_remote_irq_out + */ +static void ati_remote_irq_out(struct urb *urb) +{ + struct ati_remote *ati_remote = urb->context; + + if (urb->status) { + dev_dbg(&ati_remote->interface->dev, "%s: status %d\n", + __FUNCTION__, urb->status); + return; + } + + ati_remote->send_flags |= SEND_FLAG_COMPLETE; + wmb(); + wake_up(&ati_remote->wait); +} + +/* + * ati_remote_sendpacket + * + * Used to send device initialization strings + */ +static int ati_remote_sendpacket(struct ati_remote *ati_remote, u16 cmd, unsigned char *data) +{ + int retval = 0; + + /* Set up out_urb */ + memcpy(ati_remote->out_urb->transfer_buffer + 1, data, LO(cmd)); + ((char *) ati_remote->out_urb->transfer_buffer)[0] = HI(cmd); + + ati_remote->out_urb->transfer_buffer_length = LO(cmd) + 1; + ati_remote->out_urb->dev = ati_remote->udev; + ati_remote->send_flags = SEND_FLAG_IN_PROGRESS; + + retval = usb_submit_urb(ati_remote->out_urb, GFP_ATOMIC); + if (retval) { + dev_dbg(&ati_remote->interface->dev, + "sendpacket: usb_submit_urb failed: %d\n", retval); + return retval; + } + + wait_event_timeout(ati_remote->wait, + ((ati_remote->out_urb->status != -EINPROGRESS) || + (ati_remote->send_flags & SEND_FLAG_COMPLETE)), + HZ); + usb_kill_urb(ati_remote->out_urb); + + return retval; +} + +/* + * ati_remote_event_lookup + */ +static int ati_remote_event_lookup(int rem, unsigned char d1, unsigned char d2) +{ + int i; + + for (i = 0; ati_remote_tbl[i].kind != KIND_END; i++) { + /* + * Decide if the table entry matches the remote input. + */ + if ((((ati_remote_tbl[i].data1 & 0x0f) == (d1 & 0x0f))) && + ((((ati_remote_tbl[i].data1 >> 4) - + (d1 >> 4) + rem) & 0x0f) == 0x0f) && + (ati_remote_tbl[i].data2 == d2)) + return i; + + } + return -1; +} + +/* + * ati_remote_compute_accel + * + * Implements acceleration curve for directional control pad + * If elapsed time since last event is > 1/4 second, user "stopped", + * so reset acceleration. Otherwise, user is probably holding the control + * pad down, so we increase acceleration, ramping up over two seconds to + * a maximum speed. + */ +static int ati_remote_compute_accel(struct ati_remote *ati_remote) +{ + static const char accel[] = { 1, 2, 4, 6, 9, 13, 20 }; + unsigned long now = jiffies; + int acc; + + if (time_after(now, ati_remote->old_jiffies + msecs_to_jiffies(250))) { + acc = 1; + ati_remote->acc_jiffies = now; + } + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(125))) + acc = accel[0]; + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(250))) + acc = accel[1]; + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(500))) + acc = accel[2]; + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(1000))) + acc = accel[3]; + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(1500))) + acc = accel[4]; + else if (time_before(now, ati_remote->acc_jiffies + msecs_to_jiffies(2000))) + acc = accel[5]; + else + acc = accel[6]; + + return acc; +} + +/* + * ati_remote_report_input + */ +static void ati_remote_input_report(struct urb *urb) +{ + struct ati_remote *ati_remote = urb->context; + unsigned char *data= ati_remote->inbuf; + struct input_dev *dev = ati_remote->idev; + int index, acc; + int remote_num; + + /* Deal with strange looking inputs */ + if ( (urb->actual_length != 4) || (data[0] != 0x14) || + ((data[3] & 0x0f) != 0x00) ) { + ati_remote_dump(data, urb->actual_length); + return; + } + + /* Mask unwanted remote channels. */ + /* note: remote_num is 0-based, channel 1 on remote == 0 here */ + remote_num = (data[3] >> 4) & 0x0f; + if (channel_mask & (1 << (remote_num + 1))) { + dbginfo(&ati_remote->interface->dev, + "Masked input from channel 0x%02x: data %02x,%02x, mask= 0x%02lx\n", + remote_num, data[1], data[2], channel_mask); + return; + } + + /* Look up event code index in translation table */ + index = ati_remote_event_lookup(remote_num, data[1], data[2]); + if (index < 0) { + dev_warn(&ati_remote->interface->dev, + "Unknown input from channel 0x%02x: data %02x,%02x\n", + remote_num, data[1], data[2]); + return; + } + dbginfo(&ati_remote->interface->dev, + "channel 0x%02x; data %02x,%02x; index %d; keycode %d\n", + remote_num, data[1], data[2], index, ati_remote_tbl[index].code); + + if (ati_remote_tbl[index].kind == KIND_LITERAL) { + input_event(dev, ati_remote_tbl[index].type, + ati_remote_tbl[index].code, + ati_remote_tbl[index].value); + input_sync(dev); + + ati_remote->old_jiffies = jiffies; + return; + } + + if (ati_remote_tbl[index].kind == KIND_FILTERED) { + unsigned long now = jiffies; + + /* Filter duplicate events which happen "too close" together. */ + if (ati_remote->old_data[0] == data[1] && + ati_remote->old_data[1] == data[2] && + time_before(now, ati_remote->old_jiffies + + msecs_to_jiffies(repeat_filter))) { + ati_remote->repeat_count++; + } else { + ati_remote->repeat_count = 0; + ati_remote->first_jiffies = now; + } + + ati_remote->old_data[0] = data[1]; + ati_remote->old_data[1] = data[2]; + ati_remote->old_jiffies = now; + + /* Ensure we skip at least the 4 first duplicate events (generated + * by a single keypress), and continue skipping until repeat_delay + * msecs have passed + */ + if (ati_remote->repeat_count > 0 && + (ati_remote->repeat_count < 5 || + time_before(now, ati_remote->first_jiffies + + msecs_to_jiffies(repeat_delay)))) + return; + + + input_event(dev, ati_remote_tbl[index].type, + ati_remote_tbl[index].code, 1); + input_sync(dev); + input_event(dev, ati_remote_tbl[index].type, + ati_remote_tbl[index].code, 0); + input_sync(dev); + + } else { + + /* + * Other event kinds are from the directional control pad, and have an + * acceleration factor applied to them. Without this acceleration, the + * control pad is mostly unusable. + */ + acc = ati_remote_compute_accel(ati_remote); + + switch (ati_remote_tbl[index].kind) { + case KIND_ACCEL: + input_event(dev, ati_remote_tbl[index].type, + ati_remote_tbl[index].code, + ati_remote_tbl[index].value * acc); + break; + case KIND_LU: + input_report_rel(dev, REL_X, -acc); + input_report_rel(dev, REL_Y, -acc); + break; + case KIND_RU: + input_report_rel(dev, REL_X, acc); + input_report_rel(dev, REL_Y, -acc); + break; + case KIND_LD: + input_report_rel(dev, REL_X, -acc); + input_report_rel(dev, REL_Y, acc); + break; + case KIND_RD: + input_report_rel(dev, REL_X, acc); + input_report_rel(dev, REL_Y, acc); + break; + default: + dev_dbg(&ati_remote->interface->dev, "ati_remote kind=%d\n", + ati_remote_tbl[index].kind); + } + input_sync(dev); + + ati_remote->old_jiffies = jiffies; + ati_remote->old_data[0] = data[1]; + ati_remote->old_data[1] = data[2]; + } +} + +/* + * ati_remote_irq_in + */ +static void ati_remote_irq_in(struct urb *urb) +{ + struct ati_remote *ati_remote = urb->context; + int retval; + + switch (urb->status) { + case 0: /* success */ + ati_remote_input_report(urb); + break; + case -ECONNRESET: /* unlink */ + case -ENOENT: + case -ESHUTDOWN: + dev_dbg(&ati_remote->interface->dev, "%s: urb error status, unlink? \n", + __FUNCTION__); + return; + default: /* error */ + dev_dbg(&ati_remote->interface->dev, "%s: Nonzero urb status %d\n", + __FUNCTION__, urb->status); + } + + retval = usb_submit_urb(urb, GFP_ATOMIC); + if (retval) + dev_err(&ati_remote->interface->dev, "%s: usb_submit_urb()=%d\n", + __FUNCTION__, retval); +} + +/* + * ati_remote_alloc_buffers + */ +static int ati_remote_alloc_buffers(struct usb_device *udev, + struct ati_remote *ati_remote) +{ + ati_remote->inbuf = usb_buffer_alloc(udev, DATA_BUFSIZE, GFP_ATOMIC, + &ati_remote->inbuf_dma); + if (!ati_remote->inbuf) + return -1; + + ati_remote->outbuf = usb_buffer_alloc(udev, DATA_BUFSIZE, GFP_ATOMIC, + &ati_remote->outbuf_dma); + if (!ati_remote->outbuf) + return -1; + + ati_remote->irq_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!ati_remote->irq_urb) + return -1; + + ati_remote->out_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!ati_remote->out_urb) + return -1; + + return 0; +} + +/* + * ati_remote_free_buffers + */ +static void ati_remote_free_buffers(struct ati_remote *ati_remote) +{ + usb_free_urb(ati_remote->irq_urb); + usb_free_urb(ati_remote->out_urb); + + usb_buffer_free(ati_remote->udev, DATA_BUFSIZE, + ati_remote->inbuf, ati_remote->inbuf_dma); + + usb_buffer_free(ati_remote->udev, DATA_BUFSIZE, + ati_remote->outbuf, ati_remote->outbuf_dma); +} + +static void ati_remote_input_init(struct ati_remote *ati_remote) +{ + struct input_dev *idev = ati_remote->idev; + int i; + + idev->evbit[0] = BIT(EV_KEY) | BIT(EV_REL); + idev->keybit[LONG(BTN_MOUSE)] = ( BIT(BTN_LEFT) | BIT(BTN_RIGHT) | + BIT(BTN_SIDE) | BIT(BTN_EXTRA) ); + idev->relbit[0] = BIT(REL_X) | BIT(REL_Y); + for (i = 0; ati_remote_tbl[i].kind != KIND_END; i++) + if (ati_remote_tbl[i].type == EV_KEY) + set_bit(ati_remote_tbl[i].code, idev->keybit); + + input_set_drvdata(idev, ati_remote); + + idev->open = ati_remote_open; + idev->close = ati_remote_close; + + idev->name = ati_remote->name; + idev->phys = ati_remote->phys; + + usb_to_input_id(ati_remote->udev, &idev->id); + idev->dev.parent = &ati_remote->udev->dev; +} + +static int ati_remote_initialize(struct ati_remote *ati_remote) +{ + struct usb_device *udev = ati_remote->udev; + int pipe, maxp; + + init_waitqueue_head(&ati_remote->wait); + + /* Set up irq_urb */ + pipe = usb_rcvintpipe(udev, ati_remote->endpoint_in->bEndpointAddress); + maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); + maxp = (maxp > DATA_BUFSIZE) ? DATA_BUFSIZE : maxp; + + usb_fill_int_urb(ati_remote->irq_urb, udev, pipe, ati_remote->inbuf, + maxp, ati_remote_irq_in, ati_remote, + ati_remote->endpoint_in->bInterval); + ati_remote->irq_urb->transfer_dma = ati_remote->inbuf_dma; + ati_remote->irq_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + + /* Set up out_urb */ + pipe = usb_sndintpipe(udev, ati_remote->endpoint_out->bEndpointAddress); + maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); + maxp = (maxp > DATA_BUFSIZE) ? DATA_BUFSIZE : maxp; + + usb_fill_int_urb(ati_remote->out_urb, udev, pipe, ati_remote->outbuf, + maxp, ati_remote_irq_out, ati_remote, + ati_remote->endpoint_out->bInterval); + ati_remote->out_urb->transfer_dma = ati_remote->outbuf_dma; + ati_remote->out_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + + /* send initialization strings */ + if ((ati_remote_sendpacket(ati_remote, 0x8004, init1)) || + (ati_remote_sendpacket(ati_remote, 0x8007, init2))) { + dev_err(&ati_remote->interface->dev, + "Initializing ati_remote hardware failed.\n"); + return -EIO; + } + + return 0; +} + +/* + * ati_remote_probe + */ +static int ati_remote_probe(struct usb_interface *interface, const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(interface); + struct usb_host_interface *iface_host = interface->cur_altsetting; + struct usb_endpoint_descriptor *endpoint_in, *endpoint_out; + struct ati_remote *ati_remote; + struct input_dev *input_dev; + int err = -ENOMEM; + + if (iface_host->desc.bNumEndpoints != 2) { + err("%s: Unexpected desc.bNumEndpoints\n", __FUNCTION__); + return -ENODEV; + } + + endpoint_in = &iface_host->endpoint[0].desc; + endpoint_out = &iface_host->endpoint[1].desc; + + if (!usb_endpoint_is_int_in(endpoint_in)) { + err("%s: Unexpected endpoint_in\n", __FUNCTION__); + return -ENODEV; + } + if (le16_to_cpu(endpoint_in->wMaxPacketSize) == 0) { + err("%s: endpoint_in message size==0? \n", __FUNCTION__); + return -ENODEV; + } + + ati_remote = kzalloc(sizeof (struct ati_remote), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!ati_remote || !input_dev) + goto fail1; + + /* Allocate URB buffers, URBs */ + if (ati_remote_alloc_buffers(udev, ati_remote)) + goto fail2; + + ati_remote->endpoint_in = endpoint_in; + ati_remote->endpoint_out = endpoint_out; + ati_remote->udev = udev; + ati_remote->idev = input_dev; + ati_remote->interface = interface; + + usb_make_path(udev, ati_remote->phys, sizeof(ati_remote->phys)); + strlcpy(ati_remote->phys, "/input0", sizeof(ati_remote->phys)); + + if (udev->manufacturer) + strlcpy(ati_remote->name, udev->manufacturer, sizeof(ati_remote->name)); + + if (udev->product) + snprintf(ati_remote->name, sizeof(ati_remote->name), + "%s %s", ati_remote->name, udev->product); + + if (!strlen(ati_remote->name)) + snprintf(ati_remote->name, sizeof(ati_remote->name), + DRIVER_DESC "(%04x,%04x)", + le16_to_cpu(ati_remote->udev->descriptor.idVendor), + le16_to_cpu(ati_remote->udev->descriptor.idProduct)); + + ati_remote_input_init(ati_remote); + + /* Device Hardware Initialization - fills in ati_remote->idev from udev. */ + err = ati_remote_initialize(ati_remote); + if (err) + goto fail3; + + /* Set up and register input device */ + err = input_register_device(ati_remote->idev); + if (err) + goto fail3; + + usb_set_intfdata(interface, ati_remote); + return 0; + + fail3: usb_kill_urb(ati_remote->irq_urb); + usb_kill_urb(ati_remote->out_urb); + fail2: ati_remote_free_buffers(ati_remote); + fail1: input_free_device(input_dev); + kfree(ati_remote); + return err; +} + +/* + * ati_remote_disconnect + */ +static void ati_remote_disconnect(struct usb_interface *interface) +{ + struct ati_remote *ati_remote; + + ati_remote = usb_get_intfdata(interface); + usb_set_intfdata(interface, NULL); + if (!ati_remote) { + warn("%s - null device?\n", __FUNCTION__); + return; + } + + usb_kill_urb(ati_remote->irq_urb); + usb_kill_urb(ati_remote->out_urb); + input_unregister_device(ati_remote->idev); + ati_remote_free_buffers(ati_remote); + kfree(ati_remote); +} + +/* + * ati_remote_init + */ +static int __init ati_remote_init(void) +{ + int result; + + result = usb_register(&ati_remote_driver); + if (result) + err("usb_register error #%d\n", result); + else + info("Registered USB driver " DRIVER_DESC " v. " DRIVER_VERSION); + + return result; +} + +/* + * ati_remote_exit + */ +static void __exit ati_remote_exit(void) +{ + usb_deregister(&ati_remote_driver); +} + +/* + * module specification + */ + +module_init(ati_remote_init); +module_exit(ati_remote_exit); + +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/ati_remote2.c b/drivers/input/misc/ati_remote2.c new file mode 100644 index 00000000000..1031543e5c3 --- /dev/null +++ b/drivers/input/misc/ati_remote2.c @@ -0,0 +1,543 @@ +/* + * ati_remote2 - ATI/Philips USB RF remote driver + * + * Copyright (C) 2005 Ville Syrjala + * Copyright (C) 2007 Peter Stokes + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 + * as published by the Free Software Foundation. + */ + +#include + +#define DRIVER_DESC "ATI/Philips USB RF remote driver" +#define DRIVER_VERSION "0.2" + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_VERSION(DRIVER_VERSION); +MODULE_AUTHOR("Ville Syrjala "); +MODULE_LICENSE("GPL"); + +/* + * ATI Remote Wonder II Channel Configuration + * + * The remote control can by assigned one of sixteen "channels" in order to facilitate + * the use of multiple remote controls within range of each other. + * A remote's "channel" may be altered by pressing and holding the "PC" button for + * approximately 3 seconds, after which the button will slowly flash the count of the + * currently configured "channel", using the numeric keypad enter a number between 1 and + * 16 and then the "PC" button again, the button will slowly flash the count of the + * newly configured "channel". + */ + +static unsigned int channel_mask = 0xFFFF; +module_param(channel_mask, uint, 0644); +MODULE_PARM_DESC(channel_mask, "Bitmask of channels to accept <15:Channel16>...<1:Channel2><0:Channel1>"); + +static unsigned int mode_mask = 0x1F; +module_param(mode_mask, uint, 0644); +MODULE_PARM_DESC(mode_mask, "Bitmask of modes to accept <4:PC><3:AUX4><2:AUX3><1:AUX2><0:AUX1>"); + +static struct usb_device_id ati_remote2_id_table[] = { + { USB_DEVICE(0x0471, 0x0602) }, /* ATI Remote Wonder II */ + { } +}; +MODULE_DEVICE_TABLE(usb, ati_remote2_id_table); + +static struct { + int hw_code; + int key_code; +} ati_remote2_key_table[] = { + { 0x00, KEY_0 }, + { 0x01, KEY_1 }, + { 0x02, KEY_2 }, + { 0x03, KEY_3 }, + { 0x04, KEY_4 }, + { 0x05, KEY_5 }, + { 0x06, KEY_6 }, + { 0x07, KEY_7 }, + { 0x08, KEY_8 }, + { 0x09, KEY_9 }, + { 0x0c, KEY_POWER }, + { 0x0d, KEY_MUTE }, + { 0x10, KEY_VOLUMEUP }, + { 0x11, KEY_VOLUMEDOWN }, + { 0x20, KEY_CHANNELUP }, + { 0x21, KEY_CHANNELDOWN }, + { 0x28, KEY_FORWARD }, + { 0x29, KEY_REWIND }, + { 0x2c, KEY_PLAY }, + { 0x30, KEY_PAUSE }, + { 0x31, KEY_STOP }, + { 0x37, KEY_RECORD }, + { 0x38, KEY_DVD }, + { 0x39, KEY_TV }, + { 0x54, KEY_MENU }, + { 0x58, KEY_UP }, + { 0x59, KEY_DOWN }, + { 0x5a, KEY_LEFT }, + { 0x5b, KEY_RIGHT }, + { 0x5c, KEY_OK }, + { 0x78, KEY_A }, + { 0x79, KEY_B }, + { 0x7a, KEY_C }, + { 0x7b, KEY_D }, + { 0x7c, KEY_E }, + { 0x7d, KEY_F }, + { 0x82, KEY_ENTER }, + { 0x8e, KEY_VENDOR }, + { 0x96, KEY_COFFEE }, + { 0xa9, BTN_LEFT }, + { 0xaa, BTN_RIGHT }, + { 0xbe, KEY_QUESTION }, + { 0xd5, KEY_FRONT }, + { 0xd0, KEY_EDIT }, + { 0xf9, KEY_INFO }, + { (0x00 << 8) | 0x3f, KEY_PROG1 }, + { (0x01 << 8) | 0x3f, KEY_PROG2 }, + { (0x02 << 8) | 0x3f, KEY_PROG3 }, + { (0x03 << 8) | 0x3f, KEY_PROG4 }, + { (0x04 << 8) | 0x3f, KEY_PC }, + { 0, KEY_RESERVED } +}; + +struct ati_remote2 { + struct input_dev *idev; + struct usb_device *udev; + + struct usb_interface *intf[2]; + struct usb_endpoint_descriptor *ep[2]; + struct urb *urb[2]; + void *buf[2]; + dma_addr_t buf_dma[2]; + + unsigned long jiffies; + int mode; + + char name[64]; + char phys[64]; +}; + +static int ati_remote2_probe(struct usb_interface *interface, const struct usb_device_id *id); +static void ati_remote2_disconnect(struct usb_interface *interface); + +static struct usb_driver ati_remote2_driver = { + .name = "ati_remote2", + .probe = ati_remote2_probe, + .disconnect = ati_remote2_disconnect, + .id_table = ati_remote2_id_table, +}; + +static int ati_remote2_open(struct input_dev *idev) +{ + struct ati_remote2 *ar2 = input_get_drvdata(idev); + int r; + + r = usb_submit_urb(ar2->urb[0], GFP_KERNEL); + if (r) { + dev_err(&ar2->intf[0]->dev, + "%s: usb_submit_urb() = %d\n", __FUNCTION__, r); + return r; + } + r = usb_submit_urb(ar2->urb[1], GFP_KERNEL); + if (r) { + usb_kill_urb(ar2->urb[0]); + dev_err(&ar2->intf[1]->dev, + "%s: usb_submit_urb() = %d\n", __FUNCTION__, r); + return r; + } + + return 0; +} + +static void ati_remote2_close(struct input_dev *idev) +{ + struct ati_remote2 *ar2 = input_get_drvdata(idev); + + usb_kill_urb(ar2->urb[0]); + usb_kill_urb(ar2->urb[1]); +} + +static void ati_remote2_input_mouse(struct ati_remote2 *ar2) +{ + struct input_dev *idev = ar2->idev; + u8 *data = ar2->buf[0]; + int channel, mode; + + channel = data[0] >> 4; + + if (!((1 << channel) & channel_mask)) + return; + + mode = data[0] & 0x0F; + + if (mode > 4) { + dev_err(&ar2->intf[0]->dev, + "Unknown mode byte (%02x %02x %02x %02x)\n", + data[3], data[2], data[1], data[0]); + return; + } + + if (!((1 << mode) & mode_mask)) + return; + + input_event(idev, EV_REL, REL_X, (s8) data[1]); + input_event(idev, EV_REL, REL_Y, (s8) data[2]); + input_sync(idev); +} + +static int ati_remote2_lookup(unsigned int hw_code) +{ + int i; + + for (i = 0; ati_remote2_key_table[i].key_code != KEY_RESERVED; i++) + if (ati_remote2_key_table[i].hw_code == hw_code) + return i; + + return -1; +} + +static void ati_remote2_input_key(struct ati_remote2 *ar2) +{ + struct input_dev *idev = ar2->idev; + u8 *data = ar2->buf[1]; + int channel, mode, hw_code, index; + + channel = data[0] >> 4; + + if (!((1 << channel) & channel_mask)) + return; + + mode = data[0] & 0x0F; + + if (mode > 4) { + dev_err(&ar2->intf[1]->dev, + "Unknown mode byte (%02x %02x %02x %02x)\n", + data[3], data[2], data[1], data[0]); + return; + } + + hw_code = data[2]; + /* + * Mode keys (AUX1-AUX4, PC) all generate the same code byte. + * Use the mode byte to figure out which one was pressed. + */ + if (hw_code == 0x3f) { + /* + * For some incomprehensible reason the mouse pad generates + * events which look identical to the events from the last + * pressed mode key. Naturally we don't want to generate key + * events for the mouse pad so we filter out any subsequent + * events from the same mode key. + */ + if (ar2->mode == mode) + return; + + if (data[1] == 0) + ar2->mode = mode; + + hw_code |= mode << 8; + } + + if (!((1 << mode) & mode_mask)) + return; + + index = ati_remote2_lookup(hw_code); + if (index < 0) { + dev_err(&ar2->intf[1]->dev, + "Unknown code byte (%02x %02x %02x %02x)\n", + data[3], data[2], data[1], data[0]); + return; + } + + switch (data[1]) { + case 0: /* release */ + break; + case 1: /* press */ + ar2->jiffies = jiffies + msecs_to_jiffies(idev->rep[REP_DELAY]); + break; + case 2: /* repeat */ + + /* No repeat for mouse buttons. */ + if (ati_remote2_key_table[index].key_code == BTN_LEFT || + ati_remote2_key_table[index].key_code == BTN_RIGHT) + return; + + if (!time_after_eq(jiffies, ar2->jiffies)) + return; + + ar2->jiffies = jiffies + msecs_to_jiffies(idev->rep[REP_PERIOD]); + break; + default: + dev_err(&ar2->intf[1]->dev, + "Unknown state byte (%02x %02x %02x %02x)\n", + data[3], data[2], data[1], data[0]); + return; + } + + input_event(idev, EV_KEY, ati_remote2_key_table[index].key_code, data[1]); + input_sync(idev); +} + +static void ati_remote2_complete_mouse(struct urb *urb) +{ + struct ati_remote2 *ar2 = urb->context; + int r; + + switch (urb->status) { + case 0: + ati_remote2_input_mouse(ar2); + break; + case -ENOENT: + case -EILSEQ: + case -ECONNRESET: + case -ESHUTDOWN: + dev_dbg(&ar2->intf[0]->dev, + "%s(): urb status = %d\n", __FUNCTION__, urb->status); + return; + default: + dev_err(&ar2->intf[0]->dev, + "%s(): urb status = %d\n", __FUNCTION__, urb->status); + } + + r = usb_submit_urb(urb, GFP_ATOMIC); + if (r) + dev_err(&ar2->intf[0]->dev, + "%s(): usb_submit_urb() = %d\n", __FUNCTION__, r); +} + +static void ati_remote2_complete_key(struct urb *urb) +{ + struct ati_remote2 *ar2 = urb->context; + int r; + + switch (urb->status) { + case 0: + ati_remote2_input_key(ar2); + break; + case -ENOENT: + case -EILSEQ: + case -ECONNRESET: + case -ESHUTDOWN: + dev_dbg(&ar2->intf[1]->dev, + "%s(): urb status = %d\n", __FUNCTION__, urb->status); + return; + default: + dev_err(&ar2->intf[1]->dev, + "%s(): urb status = %d\n", __FUNCTION__, urb->status); + } + + r = usb_submit_urb(urb, GFP_ATOMIC); + if (r) + dev_err(&ar2->intf[1]->dev, + "%s(): usb_submit_urb() = %d\n", __FUNCTION__, r); +} + +static int ati_remote2_input_init(struct ati_remote2 *ar2) +{ + struct input_dev *idev; + int i, retval; + + idev = input_allocate_device(); + if (!idev) + return -ENOMEM; + + ar2->idev = idev; + input_set_drvdata(idev, ar2); + + idev->evbit[0] = BIT(EV_KEY) | BIT(EV_REP) | BIT(EV_REL); + idev->keybit[LONG(BTN_MOUSE)] = BIT(BTN_LEFT) | BIT(BTN_RIGHT); + idev->relbit[0] = BIT(REL_X) | BIT(REL_Y); + for (i = 0; ati_remote2_key_table[i].key_code != KEY_RESERVED; i++) + set_bit(ati_remote2_key_table[i].key_code, idev->keybit); + + idev->rep[REP_DELAY] = 250; + idev->rep[REP_PERIOD] = 33; + + idev->open = ati_remote2_open; + idev->close = ati_remote2_close; + + idev->name = ar2->name; + idev->phys = ar2->phys; + + usb_to_input_id(ar2->udev, &idev->id); + idev->dev.parent = &ar2->udev->dev; + + retval = input_register_device(idev); + if (retval) + input_free_device(idev); + + return retval; +} + +static int ati_remote2_urb_init(struct ati_remote2 *ar2) +{ + struct usb_device *udev = ar2->udev; + int i, pipe, maxp; + + for (i = 0; i < 2; i++) { + ar2->buf[i] = usb_buffer_alloc(udev, 4, GFP_KERNEL, &ar2->buf_dma[i]); + if (!ar2->buf[i]) + return -ENOMEM; + + ar2->urb[i] = usb_alloc_urb(0, GFP_KERNEL); + if (!ar2->urb[i]) + return -ENOMEM; + + pipe = usb_rcvintpipe(udev, ar2->ep[i]->bEndpointAddress); + maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); + maxp = maxp > 4 ? 4 : maxp; + + usb_fill_int_urb(ar2->urb[i], udev, pipe, ar2->buf[i], maxp, + i ? ati_remote2_complete_key : ati_remote2_complete_mouse, + ar2, ar2->ep[i]->bInterval); + ar2->urb[i]->transfer_dma = ar2->buf_dma[i]; + ar2->urb[i]->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + } + + return 0; +} + +static void ati_remote2_urb_cleanup(struct ati_remote2 *ar2) +{ + int i; + + for (i = 0; i < 2; i++) { + usb_free_urb(ar2->urb[i]); + usb_buffer_free(ar2->udev, 4, ar2->buf[i], ar2->buf_dma[i]); + } +} + +static int ati_remote2_setup(struct ati_remote2 *ar2) +{ + int r, i, channel; + + /* + * Configure receiver to only accept input from remote "channel" + * channel == 0 -> Accept input from any remote channel + * channel == 1 -> Only accept input from remote channel 1 + * channel == 2 -> Only accept input from remote channel 2 + * ... + * channel == 16 -> Only accept input from remote channel 16 + */ + + channel = 0; + for (i = 0; i < 16; i++) { + if ((1 << i) & channel_mask) { + if (!(~(1 << i) & 0xFFFF & channel_mask)) + channel = i + 1; + break; + } + } + + r = usb_control_msg(ar2->udev, usb_sndctrlpipe(ar2->udev, 0), + 0x20, + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, + channel, 0x0, NULL, 0, USB_CTRL_SET_TIMEOUT); + if (r) { + dev_err(&ar2->udev->dev, "%s - failed to set channel due to error: %d\n", + __FUNCTION__, r); + return r; + } + + return 0; +} + +static int ati_remote2_probe(struct usb_interface *interface, const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(interface); + struct usb_host_interface *alt = interface->cur_altsetting; + struct ati_remote2 *ar2; + int r; + + if (alt->desc.bInterfaceNumber) + return -ENODEV; + + ar2 = kzalloc(sizeof (struct ati_remote2), GFP_KERNEL); + if (!ar2) + return -ENOMEM; + + ar2->udev = udev; + + ar2->intf[0] = interface; + ar2->ep[0] = &alt->endpoint[0].desc; + + ar2->intf[1] = usb_ifnum_to_if(udev, 1); + r = usb_driver_claim_interface(&ati_remote2_driver, ar2->intf[1], ar2); + if (r) + goto fail1; + alt = ar2->intf[1]->cur_altsetting; + ar2->ep[1] = &alt->endpoint[0].desc; + + r = ati_remote2_urb_init(ar2); + if (r) + goto fail2; + + r = ati_remote2_setup(ar2); + if (r) + goto fail2; + + usb_make_path(udev, ar2->phys, sizeof(ar2->phys)); + strlcat(ar2->phys, "/input0", sizeof(ar2->phys)); + + strlcat(ar2->name, "ATI Remote Wonder II", sizeof(ar2->name)); + + r = ati_remote2_input_init(ar2); + if (r) + goto fail2; + + usb_set_intfdata(interface, ar2); + + return 0; + + fail2: + ati_remote2_urb_cleanup(ar2); + + usb_driver_release_interface(&ati_remote2_driver, ar2->intf[1]); + fail1: + kfree(ar2); + + return r; +} + +static void ati_remote2_disconnect(struct usb_interface *interface) +{ + struct ati_remote2 *ar2; + struct usb_host_interface *alt = interface->cur_altsetting; + + if (alt->desc.bInterfaceNumber) + return; + + ar2 = usb_get_intfdata(interface); + usb_set_intfdata(interface, NULL); + + input_unregister_device(ar2->idev); + + ati_remote2_urb_cleanup(ar2); + + usb_driver_release_interface(&ati_remote2_driver, ar2->intf[1]); + + kfree(ar2); +} + +static int __init ati_remote2_init(void) +{ + int r; + + r = usb_register(&ati_remote2_driver); + if (r) + printk(KERN_ERR "ati_remote2: usb_register() = %d\n", r); + else + printk(KERN_INFO "ati_remote2: " DRIVER_DESC " " DRIVER_VERSION "\n"); + + return r; +} + +static void __exit ati_remote2_exit(void) +{ + usb_deregister(&ati_remote2_driver); +} + +module_init(ati_remote2_init); +module_exit(ati_remote2_exit); diff --git a/drivers/input/misc/keyspan_remote.c b/drivers/input/misc/keyspan_remote.c new file mode 100644 index 00000000000..1bffc9fa98c --- /dev/null +++ b/drivers/input/misc/keyspan_remote.c @@ -0,0 +1,592 @@ +/* + * keyspan_remote: USB driver for the Keyspan DMR + * + * Copyright (C) 2005 Zymeta Corporation - Michael Downey (downey@zymeta.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation, version 2. + * + * This driver has been put together with the support of Innosys, Inc. + * and Keyspan, Inc the manufacturers of the Keyspan USB DMR product. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_VERSION "v0.1" +#define DRIVER_AUTHOR "Michael Downey " +#define DRIVER_DESC "Driver for the USB Keyspan remote control." +#define DRIVER_LICENSE "GPL" + +/* Parameters that can be passed to the driver. */ +static int debug; +module_param(debug, int, 0444); +MODULE_PARM_DESC(debug, "Enable extra debug messages and information"); + +/* Vendor and product ids */ +#define USB_KEYSPAN_VENDOR_ID 0x06CD +#define USB_KEYSPAN_PRODUCT_UIA11 0x0202 + +/* Defines for converting the data from the remote. */ +#define ZERO 0x18 +#define ZERO_MASK 0x1F /* 5 bits for a 0 */ +#define ONE 0x3C +#define ONE_MASK 0x3F /* 6 bits for a 1 */ +#define SYNC 0x3F80 +#define SYNC_MASK 0x3FFF /* 14 bits for a SYNC sequence */ +#define STOP 0x00 +#define STOP_MASK 0x1F /* 5 bits for the STOP sequence */ +#define GAP 0xFF + +#define RECV_SIZE 8 /* The UIA-11 type have a 8 byte limit. */ + +/* table of devices that work with this driver */ +static struct usb_device_id keyspan_table[] = { + { USB_DEVICE(USB_KEYSPAN_VENDOR_ID, USB_KEYSPAN_PRODUCT_UIA11) }, + { } /* Terminating entry */ +}; + +/* Structure to store all the real stuff that a remote sends to us. */ +struct keyspan_message { + u16 system; + u8 button; + u8 toggle; +}; + +/* Structure used for all the bit testing magic needed to be done. */ +struct bit_tester { + u32 tester; + int len; + int pos; + int bits_left; + u8 buffer[32]; +}; + +/* Structure to hold all of our driver specific stuff */ +struct usb_keyspan { + char name[128]; + char phys[64]; + struct usb_device* udev; + struct input_dev *input; + struct usb_interface* interface; + struct usb_endpoint_descriptor* in_endpoint; + struct urb* irq_urb; + int open; + dma_addr_t in_dma; + unsigned char* in_buffer; + + /* variables used to parse messages from remote. */ + struct bit_tester data; + int stage; + int toggle; +}; + +/* + * Table that maps the 31 possible keycodes to input keys. + * Currently there are 15 and 17 button models so RESERVED codes + * are blank areas in the mapping. + */ +static const int keyspan_key_table[] = { + KEY_RESERVED, /* 0 is just a place holder. */ + KEY_RESERVED, + KEY_STOP, + KEY_PLAYCD, + KEY_RESERVED, + KEY_PREVIOUSSONG, + KEY_REWIND, + KEY_FORWARD, + KEY_NEXTSONG, + KEY_RESERVED, + KEY_RESERVED, + KEY_RESERVED, + KEY_PAUSE, + KEY_VOLUMEUP, + KEY_RESERVED, + KEY_RESERVED, + KEY_RESERVED, + KEY_VOLUMEDOWN, + KEY_RESERVED, + KEY_UP, + KEY_RESERVED, + KEY_MUTE, + KEY_LEFT, + KEY_ENTER, + KEY_RIGHT, + KEY_RESERVED, + KEY_RESERVED, + KEY_DOWN, + KEY_RESERVED, + KEY_KPASTERISK, + KEY_RESERVED, + KEY_MENU +}; + +static struct usb_driver keyspan_driver; + +/* + * Debug routine that prints out what we've received from the remote. + */ +static void keyspan_print(struct usb_keyspan* dev) /*unsigned char* data)*/ +{ + char codes[4 * RECV_SIZE]; + int i; + + for (i = 0; i < RECV_SIZE; i++) + snprintf(codes + i * 3, 4, "%02x ", dev->in_buffer[i]); + + dev_info(&dev->udev->dev, "%s\n", codes); +} + +/* + * Routine that manages the bit_tester structure. It makes sure that there are + * at least bits_needed bits loaded into the tester. + */ +static int keyspan_load_tester(struct usb_keyspan* dev, int bits_needed) +{ + if (dev->data.bits_left >= bits_needed) + return 0; + + /* + * Somehow we've missed the last message. The message will be repeated + * though so it's not too big a deal + */ + if (dev->data.pos >= dev->data.len) { + dev_dbg(&dev->udev->dev, + "%s - Error ran out of data. pos: %d, len: %d\n", + __FUNCTION__, dev->data.pos, dev->data.len); + return -1; + } + + /* Load as much as we can into the tester. */ + while ((dev->data.bits_left + 7 < (sizeof(dev->data.tester) * 8)) && + (dev->data.pos < dev->data.len)) { + dev->data.tester += (dev->data.buffer[dev->data.pos++] << dev->data.bits_left); + dev->data.bits_left += 8; + } + + return 0; +} + +/* + * Routine that handles all the logic needed to parse out the message from the remote. + */ +static void keyspan_check_data(struct usb_keyspan *remote) +{ + int i; + int found = 0; + struct keyspan_message message; + + switch(remote->stage) { + case 0: + /* + * In stage 0 we want to find the start of a message. The remote sends a 0xFF as filler. + * So the first byte that isn't a FF should be the start of a new message. + */ + for (i = 0; i < RECV_SIZE && remote->in_buffer[i] == GAP; ++i); + + if (i < RECV_SIZE) { + memcpy(remote->data.buffer, remote->in_buffer, RECV_SIZE); + remote->data.len = RECV_SIZE; + remote->data.pos = 0; + remote->data.tester = 0; + remote->data.bits_left = 0; + remote->stage = 1; + } + break; + + case 1: + /* + * Stage 1 we should have 16 bytes and should be able to detect a + * SYNC. The SYNC is 14 bits, 7 0's and then 7 1's. + */ + memcpy(remote->data.buffer + remote->data.len, remote->in_buffer, RECV_SIZE); + remote->data.len += RECV_SIZE; + + found = 0; + while ((remote->data.bits_left >= 14 || remote->data.pos < remote->data.len) && !found) { + for (i = 0; i < 8; ++i) { + if (keyspan_load_tester(remote, 14) != 0) { + remote->stage = 0; + return; + } + + if ((remote->data.tester & SYNC_MASK) == SYNC) { + remote->data.tester = remote->data.tester >> 14; + remote->data.bits_left -= 14; + found = 1; + break; + } else { + remote->data.tester = remote->data.tester >> 1; + --remote->data.bits_left; + } + } + } + + if (!found) { + remote->stage = 0; + remote->data.len = 0; + } else { + remote->stage = 2; + } + break; + + case 2: + /* + * Stage 2 we should have 24 bytes which will be enough for a full + * message. We need to parse out the system code, button code, + * toggle code, and stop. + */ + memcpy(remote->data.buffer + remote->data.len, remote->in_buffer, RECV_SIZE); + remote->data.len += RECV_SIZE; + + message.system = 0; + for (i = 0; i < 9; i++) { + keyspan_load_tester(remote, 6); + + if ((remote->data.tester & ZERO_MASK) == ZERO) { + message.system = message.system << 1; + remote->data.tester = remote->data.tester >> 5; + remote->data.bits_left -= 5; + } else if ((remote->data.tester & ONE_MASK) == ONE) { + message.system = (message.system << 1) + 1; + remote->data.tester = remote->data.tester >> 6; + remote->data.bits_left -= 6; + } else { + err("%s - Unknown sequence found in system data.\n", __FUNCTION__); + remote->stage = 0; + return; + } + } + + message.button = 0; + for (i = 0; i < 5; i++) { + keyspan_load_tester(remote, 6); + + if ((remote->data.tester & ZERO_MASK) == ZERO) { + message.button = message.button << 1; + remote->data.tester = remote->data.tester >> 5; + remote->data.bits_left -= 5; + } else if ((remote->data.tester & ONE_MASK) == ONE) { + message.button = (message.button << 1) + 1; + remote->data.tester = remote->data.tester >> 6; + remote->data.bits_left -= 6; + } else { + err("%s - Unknown sequence found in button data.\n", __FUNCTION__); + remote->stage = 0; + return; + } + } + + keyspan_load_tester(remote, 6); + if ((remote->data.tester & ZERO_MASK) == ZERO) { + message.toggle = 0; + remote->data.tester = remote->data.tester >> 5; + remote->data.bits_left -= 5; + } else if ((remote->data.tester & ONE_MASK) == ONE) { + message.toggle = 1; + remote->data.tester = remote->data.tester >> 6; + remote->data.bits_left -= 6; + } else { + err("%s - Error in message, invalid toggle.\n", __FUNCTION__); + remote->stage = 0; + return; + } + + keyspan_load_tester(remote, 5); + if ((remote->data.tester & STOP_MASK) == STOP) { + remote->data.tester = remote->data.tester >> 5; + remote->data.bits_left -= 5; + } else { + err("Bad message recieved, no stop bit found.\n"); + } + + dev_dbg(&remote->udev->dev, + "%s found valid message: system: %d, button: %d, toggle: %d\n", + __FUNCTION__, message.system, message.button, message.toggle); + + if (message.toggle != remote->toggle) { + input_report_key(remote->input, keyspan_key_table[message.button], 1); + input_report_key(remote->input, keyspan_key_table[message.button], 0); + input_sync(remote->input); + remote->toggle = message.toggle; + } + + remote->stage = 0; + break; + } +} + +/* + * Routine for sending all the initialization messages to the remote. + */ +static int keyspan_setup(struct usb_device* dev) +{ + int retval = 0; + + retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + 0x11, 0x40, 0x5601, 0x0, NULL, 0, 0); + if (retval) { + dev_dbg(&dev->dev, "%s - failed to set bit rate due to error: %d\n", + __FUNCTION__, retval); + return(retval); + } + + retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + 0x44, 0x40, 0x0, 0x0, NULL, 0, 0); + if (retval) { + dev_dbg(&dev->dev, "%s - failed to set resume sensitivity due to error: %d\n", + __FUNCTION__, retval); + return(retval); + } + + retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + 0x22, 0x40, 0x0, 0x0, NULL, 0, 0); + if (retval) { + dev_dbg(&dev->dev, "%s - failed to turn receive on due to error: %d\n", + __FUNCTION__, retval); + return(retval); + } + + dev_dbg(&dev->dev, "%s - Setup complete.\n", __FUNCTION__); + return(retval); +} + +/* + * Routine used to handle a new message that has come in. + */ +static void keyspan_irq_recv(struct urb *urb) +{ + struct usb_keyspan *dev = urb->context; + int retval; + + /* Check our status in case we need to bail out early. */ + switch (urb->status) { + case 0: + break; + + /* Device went away so don't keep trying to read from it. */ + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + return; + + default: + goto resubmit; + break; + } + + if (debug) + keyspan_print(dev); + + keyspan_check_data(dev); + +resubmit: + retval = usb_submit_urb(urb, GFP_ATOMIC); + if (retval) + err ("%s - usb_submit_urb failed with result: %d", __FUNCTION__, retval); +} + +static int keyspan_open(struct input_dev *dev) +{ + struct usb_keyspan *remote = input_get_drvdata(dev); + + remote->irq_urb->dev = remote->udev; + if (usb_submit_urb(remote->irq_urb, GFP_KERNEL)) + return -EIO; + + return 0; +} + +static void keyspan_close(struct input_dev *dev) +{ + struct usb_keyspan *remote = input_get_drvdata(dev); + + usb_kill_urb(remote->irq_urb); +} + +static struct usb_endpoint_descriptor *keyspan_get_in_endpoint(struct usb_host_interface *iface) +{ + + struct usb_endpoint_descriptor *endpoint; + int i; + + for (i = 0; i < iface->desc.bNumEndpoints; ++i) { + endpoint = &iface->endpoint[i].desc; + + if (usb_endpoint_is_int_in(endpoint)) { + /* we found our interrupt in endpoint */ + return endpoint; + } + } + + return NULL; +} + +/* + * Routine that sets up the driver to handle a specific USB device detected on the bus. + */ +static int keyspan_probe(struct usb_interface *interface, const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(interface); + struct usb_endpoint_descriptor *endpoint; + struct usb_keyspan *remote; + struct input_dev *input_dev; + int i, error; + + endpoint = keyspan_get_in_endpoint(interface->cur_altsetting); + if (!endpoint) + return -ENODEV; + + remote = kzalloc(sizeof(*remote), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!remote || !input_dev) { + error = -ENOMEM; + goto fail1; + } + + remote->udev = udev; + remote->input = input_dev; + remote->interface = interface; + remote->in_endpoint = endpoint; + remote->toggle = -1; /* Set to -1 so we will always not match the toggle from the first remote message. */ + + remote->in_buffer = usb_buffer_alloc(udev, RECV_SIZE, GFP_ATOMIC, &remote->in_dma); + if (!remote->in_buffer) { + error = -ENOMEM; + goto fail1; + } + + remote->irq_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!remote->irq_urb) { + error = -ENOMEM; + goto fail2; + } + + error = keyspan_setup(udev); + if (error) { + error = -ENODEV; + goto fail3; + } + + if (udev->manufacturer) + strlcpy(remote->name, udev->manufacturer, sizeof(remote->name)); + + if (udev->product) { + if (udev->manufacturer) + strlcat(remote->name, " ", sizeof(remote->name)); + strlcat(remote->name, udev->product, sizeof(remote->name)); + } + + if (!strlen(remote->name)) + snprintf(remote->name, sizeof(remote->name), + "USB Keyspan Remote %04x:%04x", + le16_to_cpu(udev->descriptor.idVendor), + le16_to_cpu(udev->descriptor.idProduct)); + + usb_make_path(udev, remote->phys, sizeof(remote->phys)); + strlcat(remote->phys, "/input0", sizeof(remote->phys)); + + input_dev->name = remote->name; + input_dev->phys = remote->phys; + usb_to_input_id(udev, &input_dev->id); + input_dev->dev.parent = &interface->dev; + + input_dev->evbit[0] = BIT(EV_KEY); /* We will only report KEY events. */ + for (i = 0; i < ARRAY_SIZE(keyspan_key_table); i++) + if (keyspan_key_table[i] != KEY_RESERVED) + set_bit(keyspan_key_table[i], input_dev->keybit); + + input_set_drvdata(input_dev, remote); + + input_dev->open = keyspan_open; + input_dev->close = keyspan_close; + + /* + * Initialize the URB to access the device. The urb gets sent to the device in keyspan_open() + */ + usb_fill_int_urb(remote->irq_urb, + remote->udev, usb_rcvintpipe(remote->udev, remote->in_endpoint->bEndpointAddress), + remote->in_buffer, RECV_SIZE, keyspan_irq_recv, remote, + remote->in_endpoint->bInterval); + remote->irq_urb->transfer_dma = remote->in_dma; + remote->irq_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + + /* we can register the device now, as it is ready */ + error = input_register_device(remote->input); + if (error) + goto fail3; + + /* save our data pointer in this interface device */ + usb_set_intfdata(interface, remote); + + return 0; + + fail3: usb_free_urb(remote->irq_urb); + fail2: usb_buffer_free(udev, RECV_SIZE, remote->in_buffer, remote->in_dma); + fail1: kfree(remote); + input_free_device(input_dev); + + return error; +} + +/* + * Routine called when a device is disconnected from the USB. + */ +static void keyspan_disconnect(struct usb_interface *interface) +{ + struct usb_keyspan *remote; + + remote = usb_get_intfdata(interface); + usb_set_intfdata(interface, NULL); + + if (remote) { /* We have a valid driver structure so clean up everything we allocated. */ + input_unregister_device(remote->input); + usb_kill_urb(remote->irq_urb); + usb_free_urb(remote->irq_urb); + usb_buffer_free(remote->udev, RECV_SIZE, remote->in_buffer, remote->in_dma); + kfree(remote); + } +} + +/* + * Standard driver set up sections + */ +static struct usb_driver keyspan_driver = +{ + .name = "keyspan_remote", + .probe = keyspan_probe, + .disconnect = keyspan_disconnect, + .id_table = keyspan_table +}; + +static int __init usb_keyspan_init(void) +{ + int result; + + /* register this driver with the USB subsystem */ + result = usb_register(&keyspan_driver); + if (result) + err("usb_register failed. Error number %d\n", result); + + return result; +} + +static void __exit usb_keyspan_exit(void) +{ + /* deregister this driver with the USB subsystem */ + usb_deregister(&keyspan_driver); +} + +module_init(usb_keyspan_init); +module_exit(usb_keyspan_exit); + +MODULE_DEVICE_TABLE(usb, keyspan_table); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE(DRIVER_LICENSE); diff --git a/drivers/input/misc/map_to_7segment.h b/drivers/input/misc/map_to_7segment.h new file mode 100644 index 00000000000..a424094d9fe --- /dev/null +++ b/drivers/input/misc/map_to_7segment.h @@ -0,0 +1,189 @@ +/* + * drivers/usb/input/map_to_7segment.h + * + * Copyright (c) 2005 Henk Vergonet + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef MAP_TO_7SEGMENT_H +#define MAP_TO_7SEGMENT_H + +/* This file provides translation primitives and tables for the conversion + * of (ASCII) characters to a 7-segments notation. + * + * The 7 segment's wikipedia notation below is used as standard. + * See: http://en.wikipedia.org/wiki/Seven_segment_display + * + * Notation: +-a-+ + * f b + * +-g-+ + * e c + * +-d-+ + * + * Usage: + * + * Register a map variable, and fill it with a character set: + * static SEG7_DEFAULT_MAP(map_seg7); + * + * + * Then use for conversion: + * seg7 = map_to_seg7(&map_seg7, some_char); + * ... + * + * In device drivers it is recommended, if required, to make the char map + * accessible via the sysfs interface using the following scheme: + * + * static ssize_t show_map(struct device *dev, char *buf) { + * memcpy(buf, &map_seg7, sizeof(map_seg7)); + * return sizeof(map_seg7); + * } + * static ssize_t store_map(struct device *dev, const char *buf, size_t cnt) { + * if(cnt != sizeof(map_seg7)) + * return -EINVAL; + * memcpy(&map_seg7, buf, cnt); + * return cnt; + * } + * static DEVICE_ATTR(map_seg7, PERMS_RW, show_map, store_map); + * + * History: + * 2005-05-31 RFC linux-kernel@vger.kernel.org + */ +#include + + +#define BIT_SEG7_A 0 +#define BIT_SEG7_B 1 +#define BIT_SEG7_C 2 +#define BIT_SEG7_D 3 +#define BIT_SEG7_E 4 +#define BIT_SEG7_F 5 +#define BIT_SEG7_G 6 +#define BIT_SEG7_RESERVED 7 + +struct seg7_conversion_map { + unsigned char table[128]; +}; + +static inline int map_to_seg7(struct seg7_conversion_map *map, int c) +{ + return c >= 0 && c < sizeof(map->table) ? map->table[c] : -EINVAL; +} + +#define SEG7_CONVERSION_MAP(_name, _map) \ + struct seg7_conversion_map _name = { .table = { _map } } + +/* + * It is recommended to use a facility that allows user space to redefine + * custom character sets for LCD devices. Please use a sysfs interface + * as described above. + */ +#define MAP_TO_SEG7_SYSFS_FILE "map_seg7" + +/******************************************************************************* + * ASCII conversion table + ******************************************************************************/ + +#define _SEG7(l,a,b,c,d,e,f,g) \ + ( a<',1,1,0,0,0,0,1), _SEG7('?',1,1,1,0,0,1,0),\ + _SEG7('@',1,1,0,1,1,1,1), + +#define _MAP_65_90_ASCII_SEG7_ALPHA_UPPR \ + _SEG7('A',1,1,1,0,1,1,1), _SEG7('B',1,1,1,1,1,1,1), _SEG7('C',1,0,0,1,1,1,0),\ + _SEG7('D',1,1,1,1,1,1,0), _SEG7('E',1,0,0,1,1,1,1), _SEG7('F',1,0,0,0,1,1,1),\ + _SEG7('G',1,1,1,1,0,1,1), _SEG7('H',0,1,1,0,1,1,1), _SEG7('I',0,1,1,0,0,0,0),\ + _SEG7('J',0,1,1,1,0,0,0), _SEG7('K',0,1,1,0,1,1,1), _SEG7('L',0,0,0,1,1,1,0),\ + _SEG7('M',1,1,1,0,1,1,0), _SEG7('N',1,1,1,0,1,1,0), _SEG7('O',1,1,1,1,1,1,0),\ + _SEG7('P',1,1,0,0,1,1,1), _SEG7('Q',1,1,1,1,1,1,0), _SEG7('R',1,1,1,0,1,1,1),\ + _SEG7('S',1,0,1,1,0,1,1), _SEG7('T',0,0,0,1,1,1,1), _SEG7('U',0,1,1,1,1,1,0),\ + _SEG7('V',0,1,1,1,1,1,0), _SEG7('W',0,1,1,1,1,1,1), _SEG7('X',0,1,1,0,1,1,1),\ + _SEG7('Y',0,1,1,0,0,1,1), _SEG7('Z',1,1,0,1,1,0,1), + +#define _MAP_91_96_ASCII_SEG7_SYMBOL \ + _SEG7('[',1,0,0,1,1,1,0), _SEG7('\\',0,0,1,0,0,1,1),_SEG7(']',1,1,1,1,0,0,0),\ + _SEG7('^',1,1,0,0,0,1,0), _SEG7('_',0,0,0,1,0,0,0), _SEG7('`',0,1,0,0,0,0,0), + +#define _MAP_97_122_ASCII_SEG7_ALPHA_LOWER \ + _SEG7('A',1,1,1,0,1,1,1), _SEG7('b',0,0,1,1,1,1,1), _SEG7('c',0,0,0,1,1,0,1),\ + _SEG7('d',0,1,1,1,1,0,1), _SEG7('E',1,0,0,1,1,1,1), _SEG7('F',1,0,0,0,1,1,1),\ + _SEG7('G',1,1,1,1,0,1,1), _SEG7('h',0,0,1,0,1,1,1), _SEG7('i',0,0,1,0,0,0,0),\ + _SEG7('j',0,0,1,1,0,0,0), _SEG7('k',0,0,1,0,1,1,1), _SEG7('L',0,0,0,1,1,1,0),\ + _SEG7('M',1,1,1,0,1,1,0), _SEG7('n',0,0,1,0,1,0,1), _SEG7('o',0,0,1,1,1,0,1),\ + _SEG7('P',1,1,0,0,1,1,1), _SEG7('q',1,1,1,0,0,1,1), _SEG7('r',0,0,0,0,1,0,1),\ + _SEG7('S',1,0,1,1,0,1,1), _SEG7('T',0,0,0,1,1,1,1), _SEG7('u',0,0,1,1,1,0,0),\ + _SEG7('v',0,0,1,1,1,0,0), _SEG7('W',0,1,1,1,1,1,1), _SEG7('X',0,1,1,0,1,1,1),\ + _SEG7('y',0,1,1,1,0,1,1), _SEG7('Z',1,1,0,1,1,0,1), + +#define _MAP_123_126_ASCII_SEG7_SYMBOL \ + _SEG7('{',1,0,0,1,1,1,0), _SEG7('|',0,0,0,0,1,1,0), _SEG7('}',1,1,1,1,0,0,0),\ + _SEG7('~',1,0,0,0,0,0,0), + +/* Maps */ + +/* This set tries to map as close as possible to the visible characteristics + * of the ASCII symbol, lowercase and uppercase letters may differ in + * presentation on the display. + */ +#define MAP_ASCII7SEG_ALPHANUM \ + _MAP_0_32_ASCII_SEG7_NON_PRINTABLE \ + _MAP_33_47_ASCII_SEG7_SYMBOL \ + _MAP_48_57_ASCII_SEG7_NUMERIC \ + _MAP_58_64_ASCII_SEG7_SYMBOL \ + _MAP_65_90_ASCII_SEG7_ALPHA_UPPR \ + _MAP_91_96_ASCII_SEG7_SYMBOL \ + _MAP_97_122_ASCII_SEG7_ALPHA_LOWER \ + _MAP_123_126_ASCII_SEG7_SYMBOL + +/* This set tries to map as close as possible to the symbolic characteristics + * of the ASCII character for maximum discrimination. + * For now this means all alpha chars are in lower case representations. + * (This for example facilitates the use of hex numbers with uppercase input.) + */ +#define MAP_ASCII7SEG_ALPHANUM_LC \ + _MAP_0_32_ASCII_SEG7_NON_PRINTABLE \ + _MAP_33_47_ASCII_SEG7_SYMBOL \ + _MAP_48_57_ASCII_SEG7_NUMERIC \ + _MAP_58_64_ASCII_SEG7_SYMBOL \ + _MAP_97_122_ASCII_SEG7_ALPHA_LOWER \ + _MAP_91_96_ASCII_SEG7_SYMBOL \ + _MAP_97_122_ASCII_SEG7_ALPHA_LOWER \ + _MAP_123_126_ASCII_SEG7_SYMBOL + +#define SEG7_DEFAULT_MAP(_name) \ + SEG7_CONVERSION_MAP(_name,MAP_ASCII7SEG_ALPHANUM) + +#endif /* MAP_TO_7SEGMENT_H */ + diff --git a/drivers/input/misc/powermate.c b/drivers/input/misc/powermate.c new file mode 100644 index 00000000000..448a470d28f --- /dev/null +++ b/drivers/input/misc/powermate.c @@ -0,0 +1,463 @@ +/* + * A driver for the Griffin Technology, Inc. "PowerMate" USB controller dial. + * + * v1.1, (c)2002 William R Sowerbutts + * + * This device is a anodised aluminium knob which connects over USB. It can measure + * clockwise and anticlockwise rotation. The dial also acts as a pushbutton with + * a spring for automatic release. The base contains a pair of LEDs which illuminate + * the translucent base. It rotates without limit and reports its relative rotation + * back to the host when polled by the USB controller. + * + * Testing with the knob I have has shown that it measures approximately 94 "clicks" + * for one full rotation. Testing with my High Speed Rotation Actuator (ok, it was + * a variable speed cordless electric drill) has shown that the device can measure + * speeds of up to 7 clicks either clockwise or anticlockwise between pollings from + * the host. If it counts more than 7 clicks before it is polled, it will wrap back + * to zero and start counting again. This was at quite high speed, however, almost + * certainly faster than the human hand could turn it. Griffin say that it loses a + * pulse or two on a direction change; the granularity is so fine that I never + * noticed this in practice. + * + * The device's microcontroller can be programmed to set the LED to either a constant + * intensity, or to a rhythmic pulsing. Several patterns and speeds are available. + * + * Griffin were very happy to provide documentation and free hardware for development. + * + * Some userspace tools are available on the web: http://sowerbutts.com/powermate/ + * + */ + +#include +#include +#include +#include +#include +#include + +#define POWERMATE_VENDOR 0x077d /* Griffin Technology, Inc. */ +#define POWERMATE_PRODUCT_NEW 0x0410 /* Griffin PowerMate */ +#define POWERMATE_PRODUCT_OLD 0x04AA /* Griffin soundKnob */ + +#define CONTOUR_VENDOR 0x05f3 /* Contour Design, Inc. */ +#define CONTOUR_JOG 0x0240 /* Jog and Shuttle */ + +/* these are the command codes we send to the device */ +#define SET_STATIC_BRIGHTNESS 0x01 +#define SET_PULSE_ASLEEP 0x02 +#define SET_PULSE_AWAKE 0x03 +#define SET_PULSE_MODE 0x04 + +/* these refer to bits in the powermate_device's requires_update field. */ +#define UPDATE_STATIC_BRIGHTNESS (1<<0) +#define UPDATE_PULSE_ASLEEP (1<<1) +#define UPDATE_PULSE_AWAKE (1<<2) +#define UPDATE_PULSE_MODE (1<<3) + +/* at least two versions of the hardware exist, with differing payload + sizes. the first three bytes always contain the "interesting" data in + the relevant format. */ +#define POWERMATE_PAYLOAD_SIZE_MAX 6 +#define POWERMATE_PAYLOAD_SIZE_MIN 3 +struct powermate_device { + signed char *data; + dma_addr_t data_dma; + struct urb *irq, *config; + struct usb_ctrlrequest *configcr; + dma_addr_t configcr_dma; + struct usb_device *udev; + struct input_dev *input; + spinlock_t lock; + int static_brightness; + int pulse_speed; + int pulse_table; + int pulse_asleep; + int pulse_awake; + int requires_update; // physical settings which are out of sync + char phys[64]; +}; + +static char pm_name_powermate[] = "Griffin PowerMate"; +static char pm_name_soundknob[] = "Griffin SoundKnob"; + +static void powermate_config_complete(struct urb *urb); + +/* Callback for data arriving from the PowerMate over the USB interrupt pipe */ +static void powermate_irq(struct urb *urb) +{ + struct powermate_device *pm = urb->context; + int retval; + + switch (urb->status) { + case 0: + /* success */ + break; + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + /* this urb is terminated, clean up */ + dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status); + return; + default: + dbg("%s - nonzero urb status received: %d", __FUNCTION__, urb->status); + goto exit; + } + + /* handle updates to device state */ + input_report_key(pm->input, BTN_0, pm->data[0] & 0x01); + input_report_rel(pm->input, REL_DIAL, pm->data[1]); + input_sync(pm->input); + +exit: + retval = usb_submit_urb (urb, GFP_ATOMIC); + if (retval) + err ("%s - usb_submit_urb failed with result %d", + __FUNCTION__, retval); +} + +/* Decide if we need to issue a control message and do so. Must be called with pm->lock taken */ +static void powermate_sync_state(struct powermate_device *pm) +{ + if (pm->requires_update == 0) + return; /* no updates are required */ + if (pm->config->status == -EINPROGRESS) + return; /* an update is already in progress; it'll issue this update when it completes */ + + if (pm->requires_update & UPDATE_PULSE_ASLEEP){ + pm->configcr->wValue = cpu_to_le16( SET_PULSE_ASLEEP ); + pm->configcr->wIndex = cpu_to_le16( pm->pulse_asleep ? 1 : 0 ); + pm->requires_update &= ~UPDATE_PULSE_ASLEEP; + }else if (pm->requires_update & UPDATE_PULSE_AWAKE){ + pm->configcr->wValue = cpu_to_le16( SET_PULSE_AWAKE ); + pm->configcr->wIndex = cpu_to_le16( pm->pulse_awake ? 1 : 0 ); + pm->requires_update &= ~UPDATE_PULSE_AWAKE; + }else if (pm->requires_update & UPDATE_PULSE_MODE){ + int op, arg; + /* the powermate takes an operation and an argument for its pulse algorithm. + the operation can be: + 0: divide the speed + 1: pulse at normal speed + 2: multiply the speed + the argument only has an effect for operations 0 and 2, and ranges between + 1 (least effect) to 255 (maximum effect). + + thus, several states are equivalent and are coalesced into one state. + + we map this onto a range from 0 to 510, with: + 0 -- 254 -- use divide (0 = slowest) + 255 -- use normal speed + 256 -- 510 -- use multiple (510 = fastest). + + Only values of 'arg' quite close to 255 are particularly useful/spectacular. + */ + if (pm->pulse_speed < 255) { + op = 0; // divide + arg = 255 - pm->pulse_speed; + } else if (pm->pulse_speed > 255) { + op = 2; // multiply + arg = pm->pulse_speed - 255; + } else { + op = 1; // normal speed + arg = 0; // can be any value + } + pm->configcr->wValue = cpu_to_le16( (pm->pulse_table << 8) | SET_PULSE_MODE ); + pm->configcr->wIndex = cpu_to_le16( (arg << 8) | op ); + pm->requires_update &= ~UPDATE_PULSE_MODE; + } else if (pm->requires_update & UPDATE_STATIC_BRIGHTNESS) { + pm->configcr->wValue = cpu_to_le16( SET_STATIC_BRIGHTNESS ); + pm->configcr->wIndex = cpu_to_le16( pm->static_brightness ); + pm->requires_update &= ~UPDATE_STATIC_BRIGHTNESS; + } else { + printk(KERN_ERR "powermate: unknown update required"); + pm->requires_update = 0; /* fudge the bug */ + return; + } + +/* printk("powermate: %04x %04x\n", pm->configcr->wValue, pm->configcr->wIndex); */ + + pm->configcr->bRequestType = 0x41; /* vendor request */ + pm->configcr->bRequest = 0x01; + pm->configcr->wLength = 0; + + usb_fill_control_urb(pm->config, pm->udev, usb_sndctrlpipe(pm->udev, 0), + (void *) pm->configcr, NULL, 0, + powermate_config_complete, pm); + pm->config->setup_dma = pm->configcr_dma; + pm->config->transfer_flags |= URB_NO_SETUP_DMA_MAP; + + if (usb_submit_urb(pm->config, GFP_ATOMIC)) + printk(KERN_ERR "powermate: usb_submit_urb(config) failed"); +} + +/* Called when our asynchronous control message completes. We may need to issue another immediately */ +static void powermate_config_complete(struct urb *urb) +{ + struct powermate_device *pm = urb->context; + unsigned long flags; + + if (urb->status) + printk(KERN_ERR "powermate: config urb returned %d\n", urb->status); + + spin_lock_irqsave(&pm->lock, flags); + powermate_sync_state(pm); + spin_unlock_irqrestore(&pm->lock, flags); +} + +/* Set the LED up as described and begin the sync with the hardware if required */ +static void powermate_pulse_led(struct powermate_device *pm, int static_brightness, int pulse_speed, + int pulse_table, int pulse_asleep, int pulse_awake) +{ + unsigned long flags; + + if (pulse_speed < 0) + pulse_speed = 0; + if (pulse_table < 0) + pulse_table = 0; + if (pulse_speed > 510) + pulse_speed = 510; + if (pulse_table > 2) + pulse_table = 2; + + pulse_asleep = !!pulse_asleep; + pulse_awake = !!pulse_awake; + + + spin_lock_irqsave(&pm->lock, flags); + + /* mark state updates which are required */ + if (static_brightness != pm->static_brightness) { + pm->static_brightness = static_brightness; + pm->requires_update |= UPDATE_STATIC_BRIGHTNESS; + } + if (pulse_asleep != pm->pulse_asleep) { + pm->pulse_asleep = pulse_asleep; + pm->requires_update |= (UPDATE_PULSE_ASLEEP | UPDATE_STATIC_BRIGHTNESS); + } + if (pulse_awake != pm->pulse_awake) { + pm->pulse_awake = pulse_awake; + pm->requires_update |= (UPDATE_PULSE_AWAKE | UPDATE_STATIC_BRIGHTNESS); + } + if (pulse_speed != pm->pulse_speed || pulse_table != pm->pulse_table) { + pm->pulse_speed = pulse_speed; + pm->pulse_table = pulse_table; + pm->requires_update |= UPDATE_PULSE_MODE; + } + + powermate_sync_state(pm); + + spin_unlock_irqrestore(&pm->lock, flags); +} + +/* Callback from the Input layer when an event arrives from userspace to configure the LED */ +static int powermate_input_event(struct input_dev *dev, unsigned int type, unsigned int code, int _value) +{ + unsigned int command = (unsigned int)_value; + struct powermate_device *pm = input_get_drvdata(dev); + + if (type == EV_MSC && code == MSC_PULSELED){ + /* + bits 0- 7: 8 bits: LED brightness + bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = faster. + bits 17-18: 2 bits: pulse table (0, 1, 2 valid) + bit 19: 1 bit : pulse whilst asleep? + bit 20: 1 bit : pulse constantly? + */ + int static_brightness = command & 0xFF; // bits 0-7 + int pulse_speed = (command >> 8) & 0x1FF; // bits 8-16 + int pulse_table = (command >> 17) & 0x3; // bits 17-18 + int pulse_asleep = (command >> 19) & 0x1; // bit 19 + int pulse_awake = (command >> 20) & 0x1; // bit 20 + + powermate_pulse_led(pm, static_brightness, pulse_speed, pulse_table, pulse_asleep, pulse_awake); + } + + return 0; +} + +static int powermate_alloc_buffers(struct usb_device *udev, struct powermate_device *pm) +{ + pm->data = usb_buffer_alloc(udev, POWERMATE_PAYLOAD_SIZE_MAX, + GFP_ATOMIC, &pm->data_dma); + if (!pm->data) + return -1; + + pm->configcr = usb_buffer_alloc(udev, sizeof(*(pm->configcr)), + GFP_ATOMIC, &pm->configcr_dma); + if (!pm->configcr) + return -1; + + return 0; +} + +static void powermate_free_buffers(struct usb_device *udev, struct powermate_device *pm) +{ + usb_buffer_free(udev, POWERMATE_PAYLOAD_SIZE_MAX, + pm->data, pm->data_dma); + usb_buffer_free(udev, sizeof(*(pm->configcr)), + pm->configcr, pm->configcr_dma); +} + +/* Called whenever a USB device matching one in our supported devices table is connected */ +static int powermate_probe(struct usb_interface *intf, const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev (intf); + struct usb_host_interface *interface; + struct usb_endpoint_descriptor *endpoint; + struct powermate_device *pm; + struct input_dev *input_dev; + int pipe, maxp; + int error = -ENOMEM; + + interface = intf->cur_altsetting; + endpoint = &interface->endpoint[0].desc; + if (!usb_endpoint_is_int_in(endpoint)) + return -EIO; + + usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + 0x0a, USB_TYPE_CLASS | USB_RECIP_INTERFACE, + 0, interface->desc.bInterfaceNumber, NULL, 0, + USB_CTRL_SET_TIMEOUT); + + pm = kzalloc(sizeof(struct powermate_device), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!pm || !input_dev) + goto fail1; + + if (powermate_alloc_buffers(udev, pm)) + goto fail2; + + pm->irq = usb_alloc_urb(0, GFP_KERNEL); + if (!pm->irq) + goto fail2; + + pm->config = usb_alloc_urb(0, GFP_KERNEL); + if (!pm->config) + goto fail3; + + pm->udev = udev; + pm->input = input_dev; + + usb_make_path(udev, pm->phys, sizeof(pm->phys)); + strlcpy(pm->phys, "/input0", sizeof(pm->phys)); + + spin_lock_init(&pm->lock); + + switch (le16_to_cpu(udev->descriptor.idProduct)) { + case POWERMATE_PRODUCT_NEW: + input_dev->name = pm_name_powermate; + break; + case POWERMATE_PRODUCT_OLD: + input_dev->name = pm_name_soundknob; + break; + default: + input_dev->name = pm_name_soundknob; + printk(KERN_WARNING "powermate: unknown product id %04x\n", + le16_to_cpu(udev->descriptor.idProduct)); + } + + input_dev->phys = pm->phys; + usb_to_input_id(udev, &input_dev->id); + input_dev->dev.parent = &intf->dev; + + input_set_drvdata(input_dev, pm); + + input_dev->event = powermate_input_event; + + input_dev->evbit[0] = BIT(EV_KEY) | BIT(EV_REL) | BIT(EV_MSC); + input_dev->keybit[LONG(BTN_0)] = BIT(BTN_0); + input_dev->relbit[LONG(REL_DIAL)] = BIT(REL_DIAL); + input_dev->mscbit[LONG(MSC_PULSELED)] = BIT(MSC_PULSELED); + + /* get a handle to the interrupt data pipe */ + pipe = usb_rcvintpipe(udev, endpoint->bEndpointAddress); + maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); + + if (maxp < POWERMATE_PAYLOAD_SIZE_MIN || maxp > POWERMATE_PAYLOAD_SIZE_MAX) { + printk(KERN_WARNING "powermate: Expected payload of %d--%d bytes, found %d bytes!\n", + POWERMATE_PAYLOAD_SIZE_MIN, POWERMATE_PAYLOAD_SIZE_MAX, maxp); + maxp = POWERMATE_PAYLOAD_SIZE_MAX; + } + + usb_fill_int_urb(pm->irq, udev, pipe, pm->data, + maxp, powermate_irq, + pm, endpoint->bInterval); + pm->irq->transfer_dma = pm->data_dma; + pm->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + + /* register our interrupt URB with the USB system */ + if (usb_submit_urb(pm->irq, GFP_KERNEL)) { + error = -EIO; + goto fail4; + } + + error = input_register_device(pm->input); + if (error) + goto fail5; + + + /* force an update of everything */ + pm->requires_update = UPDATE_PULSE_ASLEEP | UPDATE_PULSE_AWAKE | UPDATE_PULSE_MODE | UPDATE_STATIC_BRIGHTNESS; + powermate_pulse_led(pm, 0x80, 255, 0, 1, 0); // set default pulse parameters + + usb_set_intfdata(intf, pm); + return 0; + + fail5: usb_kill_urb(pm->irq); + fail4: usb_free_urb(pm->config); + fail3: usb_free_urb(pm->irq); + fail2: powermate_free_buffers(udev, pm); + fail1: input_free_device(input_dev); + kfree(pm); + return error; +} + +/* Called when a USB device we've accepted ownership of is removed */ +static void powermate_disconnect(struct usb_interface *intf) +{ + struct powermate_device *pm = usb_get_intfdata (intf); + + usb_set_intfdata(intf, NULL); + if (pm) { + pm->requires_update = 0; + usb_kill_urb(pm->irq); + input_unregister_device(pm->input); + usb_free_urb(pm->irq); + usb_free_urb(pm->config); + powermate_free_buffers(interface_to_usbdev(intf), pm); + + kfree(pm); + } +} + +static struct usb_device_id powermate_devices [] = { + { USB_DEVICE(POWERMATE_VENDOR, POWERMATE_PRODUCT_NEW) }, + { USB_DEVICE(POWERMATE_VENDOR, POWERMATE_PRODUCT_OLD) }, + { USB_DEVICE(CONTOUR_VENDOR, CONTOUR_JOG) }, + { } /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE (usb, powermate_devices); + +static struct usb_driver powermate_driver = { + .name = "powermate", + .probe = powermate_probe, + .disconnect = powermate_disconnect, + .id_table = powermate_devices, +}; + +static int __init powermate_init(void) +{ + return usb_register(&powermate_driver); +} + +static void __exit powermate_cleanup(void) +{ + usb_deregister(&powermate_driver); +} + +module_init(powermate_init); +module_exit(powermate_cleanup); + +MODULE_AUTHOR( "William R Sowerbutts" ); +MODULE_DESCRIPTION( "Griffin Technology, Inc PowerMate driver" ); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/yealink.c b/drivers/input/misc/yealink.c new file mode 100644 index 00000000000..ab15880fd56 --- /dev/null +++ b/drivers/input/misc/yealink.c @@ -0,0 +1,1004 @@ +/* + * drivers/usb/input/yealink.c + * + * Copyright (c) 2005 Henk Vergonet + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +/* + * Description: + * Driver for the USB-P1K voip usb phone. + * This device is produced by Yealink Network Technology Co Ltd + * but may be branded under several names: + * - Yealink usb-p1k + * - Tiptel 115 + * - ... + * + * This driver is based on: + * - the usbb2k-api http://savannah.nongnu.org/projects/usbb2k-api/ + * - information from http://memeteau.free.fr/usbb2k + * - the xpad-driver drivers/input/joystick/xpad.c + * + * Thanks to: + * - Olivier Vandorpe, for providing the usbb2k-api. + * - Martin Diehl, for spotting my memory allocation bug. + * + * History: + * 20050527 henk First version, functional keyboard. Keyboard events + * will pop-up on the ../input/eventX bus. + * 20050531 henk Added led, LCD, dialtone and sysfs interface. + * 20050610 henk Cleanups, make it ready for public consumption. + * 20050630 henk Cleanups, fixes in response to comments. + * 20050701 henk sysfs write serialisation, fix potential unload races + * 20050801 henk Added ringtone, restructure USB + * 20050816 henk Merge 2.6.13-rc6 + */ + +#include +#include +#include +#include +#include +#include + +#include "map_to_7segment.h" +#include "yealink.h" + +#define DRIVER_VERSION "yld-20051230" +#define DRIVER_AUTHOR "Henk Vergonet" +#define DRIVER_DESC "Yealink phone driver" + +#define YEALINK_POLLING_FREQUENCY 10 /* in [Hz] */ + +struct yld_status { + u8 lcd[24]; + u8 led; + u8 dialtone; + u8 ringtone; + u8 keynum; +} __attribute__ ((packed)); + +/* + * Register the LCD segment and icon map + */ +#define _LOC(k,l) { .a = (k), .m = (l) } +#define _SEG(t, a, am, b, bm, c, cm, d, dm, e, em, f, fm, g, gm) \ + { .type = (t), \ + .u = { .s = { _LOC(a, am), _LOC(b, bm), _LOC(c, cm), \ + _LOC(d, dm), _LOC(e, em), _LOC(g, gm), \ + _LOC(f, fm) } } } +#define _PIC(t, h, hm, n) \ + { .type = (t), \ + .u = { .p = { .name = (n), .a = (h), .m = (hm) } } } + +static const struct lcd_segment_map { + char type; + union { + struct pictogram_map { + u8 a,m; + char name[10]; + } p; + struct segment_map { + u8 a,m; + } s[7]; + } u; +} lcdMap[] = { +#include "yealink.h" +}; + +struct yealink_dev { + struct input_dev *idev; /* input device */ + struct usb_device *udev; /* usb device */ + + /* irq input channel */ + struct yld_ctl_packet *irq_data; + dma_addr_t irq_dma; + struct urb *urb_irq; + + /* control output channel */ + struct yld_ctl_packet *ctl_data; + dma_addr_t ctl_dma; + struct usb_ctrlrequest *ctl_req; + dma_addr_t ctl_req_dma; + struct urb *urb_ctl; + + char phys[64]; /* physical device path */ + + u8 lcdMap[ARRAY_SIZE(lcdMap)]; /* state of LCD, LED ... */ + int key_code; /* last reported key */ + + int stat_ix; + union { + struct yld_status s; + u8 b[sizeof(struct yld_status)]; + } master, copy; +}; + + +/******************************************************************************* + * Yealink lcd interface + ******************************************************************************/ + +/* + * Register a default 7 segment character set + */ +static SEG7_DEFAULT_MAP(map_seg7); + + /* Display a char, + * char '\9' and '\n' are placeholders and do not overwrite the original text. + * A space will always hide an icon. + */ +static int setChar(struct yealink_dev *yld, int el, int chr) +{ + int i, a, m, val; + + if (el >= ARRAY_SIZE(lcdMap)) + return -EINVAL; + + if (chr == '\t' || chr == '\n') + return 0; + + yld->lcdMap[el] = chr; + + if (lcdMap[el].type == '.') { + a = lcdMap[el].u.p.a; + m = lcdMap[el].u.p.m; + if (chr != ' ') + yld->master.b[a] |= m; + else + yld->master.b[a] &= ~m; + return 0; + } + + val = map_to_seg7(&map_seg7, chr); + for (i = 0; i < ARRAY_SIZE(lcdMap[0].u.s); i++) { + m = lcdMap[el].u.s[i].m; + + if (m == 0) + continue; + + a = lcdMap[el].u.s[i].a; + if (val & 1) + yld->master.b[a] |= m; + else + yld->master.b[a] &= ~m; + val = val >> 1; + } + return 0; +}; + +/******************************************************************************* + * Yealink key interface + ******************************************************************************/ + +/* Map device buttons to internal key events. + * + * USB-P1K button layout: + * + * up + * IN OUT + * down + * + * pickup C hangup + * 1 2 3 + * 4 5 6 + * 7 8 9 + * * 0 # + * + * The "up" and "down" keys, are symbolised by arrows on the button. + * The "pickup" and "hangup" keys are symbolised by a green and red phone + * on the button. + */ +static int map_p1k_to_key(int scancode) +{ + switch(scancode) { /* phone key: */ + case 0x23: return KEY_LEFT; /* IN */ + case 0x33: return KEY_UP; /* up */ + case 0x04: return KEY_RIGHT; /* OUT */ + case 0x24: return KEY_DOWN; /* down */ + case 0x03: return KEY_ENTER; /* pickup */ + case 0x14: return KEY_BACKSPACE; /* C */ + case 0x13: return KEY_ESC; /* hangup */ + case 0x00: return KEY_1; /* 1 */ + case 0x01: return KEY_2; /* 2 */ + case 0x02: return KEY_3; /* 3 */ + case 0x10: return KEY_4; /* 4 */ + case 0x11: return KEY_5; /* 5 */ + case 0x12: return KEY_6; /* 6 */ + case 0x20: return KEY_7; /* 7 */ + case 0x21: return KEY_8; /* 8 */ + case 0x22: return KEY_9; /* 9 */ + case 0x30: return KEY_KPASTERISK; /* * */ + case 0x31: return KEY_0; /* 0 */ + case 0x32: return KEY_LEFTSHIFT | + KEY_3 << 8; /* # */ + } + return -EINVAL; +} + +/* Completes a request by converting the data into events for the + * input subsystem. + * + * The key parameter can be cascaded: key2 << 8 | key1 + */ +static void report_key(struct yealink_dev *yld, int key) +{ + struct input_dev *idev = yld->idev; + + if (yld->key_code >= 0) { + /* old key up */ + input_report_key(idev, yld->key_code & 0xff, 0); + if (yld->key_code >> 8) + input_report_key(idev, yld->key_code >> 8, 0); + } + + yld->key_code = key; + if (key >= 0) { + /* new valid key */ + input_report_key(idev, key & 0xff, 1); + if (key >> 8) + input_report_key(idev, key >> 8, 1); + } + input_sync(idev); +} + +/******************************************************************************* + * Yealink usb communication interface + ******************************************************************************/ + +static int yealink_cmd(struct yealink_dev *yld, struct yld_ctl_packet *p) +{ + u8 *buf = (u8 *)p; + int i; + u8 sum = 0; + + for(i=0; isum = sum; + return usb_control_msg(yld->udev, + usb_sndctrlpipe(yld->udev, 0), + USB_REQ_SET_CONFIGURATION, + USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_OUT, + 0x200, 3, + p, sizeof(*p), + USB_CTRL_SET_TIMEOUT); +} + +static u8 default_ringtone[] = { + 0xEF, /* volume [0-255] */ + 0xFB, 0x1E, 0x00, 0x0C, /* 1250 [hz], 12/100 [s] */ + 0xFC, 0x18, 0x00, 0x0C, /* 1000 [hz], 12/100 [s] */ + 0xFB, 0x1E, 0x00, 0x0C, + 0xFC, 0x18, 0x00, 0x0C, + 0xFB, 0x1E, 0x00, 0x0C, + 0xFC, 0x18, 0x00, 0x0C, + 0xFB, 0x1E, 0x00, 0x0C, + 0xFC, 0x18, 0x00, 0x0C, + 0xFF, 0xFF, 0x01, 0x90, /* silent, 400/100 [s] */ + 0x00, 0x00 /* end of sequence */ +}; + +static int yealink_set_ringtone(struct yealink_dev *yld, u8 *buf, size_t size) +{ + struct yld_ctl_packet *p = yld->ctl_data; + int ix, len; + + if (size <= 0) + return -EINVAL; + + /* Set the ringtone volume */ + memset(yld->ctl_data, 0, sizeof(*(yld->ctl_data))); + yld->ctl_data->cmd = CMD_RING_VOLUME; + yld->ctl_data->size = 1; + yld->ctl_data->data[0] = buf[0]; + yealink_cmd(yld, p); + + buf++; + size--; + + p->cmd = CMD_RING_NOTE; + ix = 0; + while (size != ix) { + len = size - ix; + if (len > sizeof(p->data)) + len = sizeof(p->data); + p->size = len; + p->offset = cpu_to_be16(ix); + memcpy(p->data, &buf[ix], len); + yealink_cmd(yld, p); + ix += len; + } + return 0; +} + +/* keep stat_master & stat_copy in sync. + */ +static int yealink_do_idle_tasks(struct yealink_dev *yld) +{ + u8 val; + int i, ix, len; + + ix = yld->stat_ix; + + memset(yld->ctl_data, 0, sizeof(*(yld->ctl_data))); + yld->ctl_data->cmd = CMD_KEYPRESS; + yld->ctl_data->size = 1; + yld->ctl_data->sum = 0xff - CMD_KEYPRESS; + + /* If state update pointer wraps do a KEYPRESS first. */ + if (ix >= sizeof(yld->master)) { + yld->stat_ix = 0; + return 0; + } + + /* find update candidates: copy != master */ + do { + val = yld->master.b[ix]; + if (val != yld->copy.b[ix]) + goto send_update; + } while (++ix < sizeof(yld->master)); + + /* nothing todo, wait a bit and poll for a KEYPRESS */ + yld->stat_ix = 0; + /* TODO how can we wait abit. ?? + * msleep_interruptible(1000 / YEALINK_POLLING_FREQUENCY); + */ + return 0; + +send_update: + + /* Setup an appropriate update request */ + yld->copy.b[ix] = val; + yld->ctl_data->data[0] = val; + + switch(ix) { + case offsetof(struct yld_status, led): + yld->ctl_data->cmd = CMD_LED; + yld->ctl_data->sum = -1 - CMD_LED - val; + break; + case offsetof(struct yld_status, dialtone): + yld->ctl_data->cmd = CMD_DIALTONE; + yld->ctl_data->sum = -1 - CMD_DIALTONE - val; + break; + case offsetof(struct yld_status, ringtone): + yld->ctl_data->cmd = CMD_RINGTONE; + yld->ctl_data->sum = -1 - CMD_RINGTONE - val; + break; + case offsetof(struct yld_status, keynum): + val--; + val &= 0x1f; + yld->ctl_data->cmd = CMD_SCANCODE; + yld->ctl_data->offset = cpu_to_be16(val); + yld->ctl_data->data[0] = 0; + yld->ctl_data->sum = -1 - CMD_SCANCODE - val; + break; + default: + len = sizeof(yld->master.s.lcd) - ix; + if (len > sizeof(yld->ctl_data->data)) + len = sizeof(yld->ctl_data->data); + + /* Combine up to consecutive LCD bytes in a singe request + */ + yld->ctl_data->cmd = CMD_LCD; + yld->ctl_data->offset = cpu_to_be16(ix); + yld->ctl_data->size = len; + yld->ctl_data->sum = -CMD_LCD - ix - val - len; + for(i=1; imaster.b[ix]; + yld->copy.b[ix] = val; + yld->ctl_data->data[i] = val; + yld->ctl_data->sum -= val; + } + } + yld->stat_ix = ix + 1; + return 1; +} + +/* Decide on how to handle responses + * + * The state transition diagram is somethhing like: + * + * syncState<--+ + * | | + * | idle + * \|/ | + * init --ok--> waitForKey --ok--> getKey + * ^ ^ | + * | +-------ok-------+ + * error,start + * + */ +static void urb_irq_callback(struct urb *urb) +{ + struct yealink_dev *yld = urb->context; + int ret; + + if (urb->status) + err("%s - urb status %d", __FUNCTION__, urb->status); + + switch (yld->irq_data->cmd) { + case CMD_KEYPRESS: + + yld->master.s.keynum = yld->irq_data->data[0]; + break; + + case CMD_SCANCODE: + dbg("get scancode %x", yld->irq_data->data[0]); + + report_key(yld, map_p1k_to_key(yld->irq_data->data[0])); + break; + + default: + err("unexpected response %x", yld->irq_data->cmd); + } + + yealink_do_idle_tasks(yld); + + ret = usb_submit_urb(yld->urb_ctl, GFP_ATOMIC); + if (ret) + err("%s - usb_submit_urb failed %d", __FUNCTION__, ret); +} + +static void urb_ctl_callback(struct urb *urb) +{ + struct yealink_dev *yld = urb->context; + int ret; + + if (urb->status) + err("%s - urb status %d", __FUNCTION__, urb->status); + + switch (yld->ctl_data->cmd) { + case CMD_KEYPRESS: + case CMD_SCANCODE: + /* ask for a response */ + ret = usb_submit_urb(yld->urb_irq, GFP_ATOMIC); + break; + default: + /* send new command */ + yealink_do_idle_tasks(yld); + ret = usb_submit_urb(yld->urb_ctl, GFP_ATOMIC); + } + + if (ret) + err("%s - usb_submit_urb failed %d", __FUNCTION__, ret); +} + +/******************************************************************************* + * input event interface + ******************************************************************************/ + +/* TODO should we issue a ringtone on a SND_BELL event? +static int input_ev(struct input_dev *dev, unsigned int type, + unsigned int code, int value) +{ + + if (type != EV_SND) + return -EINVAL; + + switch (code) { + case SND_BELL: + case SND_TONE: + break; + default: + return -EINVAL; + } + + return 0; +} +*/ + +static int input_open(struct input_dev *dev) +{ + struct yealink_dev *yld = input_get_drvdata(dev); + int i, ret; + + dbg("%s", __FUNCTION__); + + /* force updates to device */ + for (i = 0; imaster); i++) + yld->copy.b[i] = ~yld->master.b[i]; + yld->key_code = -1; /* no keys pressed */ + + yealink_set_ringtone(yld, default_ringtone, sizeof(default_ringtone)); + + /* issue INIT */ + memset(yld->ctl_data, 0, sizeof(*(yld->ctl_data))); + yld->ctl_data->cmd = CMD_INIT; + yld->ctl_data->size = 10; + yld->ctl_data->sum = 0x100-CMD_INIT-10; + if ((ret = usb_submit_urb(yld->urb_ctl, GFP_KERNEL)) != 0) { + dbg("%s - usb_submit_urb failed with result %d", + __FUNCTION__, ret); + return ret; + } + return 0; +} + +static void input_close(struct input_dev *dev) +{ + struct yealink_dev *yld = input_get_drvdata(dev); + + usb_kill_urb(yld->urb_ctl); + usb_kill_urb(yld->urb_irq); +} + +/******************************************************************************* + * sysfs interface + ******************************************************************************/ + +static DECLARE_RWSEM(sysfs_rwsema); + +/* Interface to the 7-segments translation table aka. char set. + */ +static ssize_t show_map(struct device *dev, struct device_attribute *attr, + char *buf) +{ + memcpy(buf, &map_seg7, sizeof(map_seg7)); + return sizeof(map_seg7); +} + +static ssize_t store_map(struct device *dev, struct device_attribute *attr, + const char *buf, size_t cnt) +{ + if (cnt != sizeof(map_seg7)) + return -EINVAL; + memcpy(&map_seg7, buf, sizeof(map_seg7)); + return sizeof(map_seg7); +} + +/* Interface to the LCD. + */ + +/* Reading /sys/../lineX will return the format string with its settings: + * + * Example: + * cat ./line3 + * 888888888888 + * Linux Rocks! + */ +static ssize_t show_line(struct device *dev, char *buf, int a, int b) +{ + struct yealink_dev *yld; + int i; + + down_read(&sysfs_rwsema); + yld = dev_get_drvdata(dev); + if (yld == NULL) { + up_read(&sysfs_rwsema); + return -ENODEV; + } + + for (i = a; i < b; i++) + *buf++ = lcdMap[i].type; + *buf++ = '\n'; + for (i = a; i < b; i++) + *buf++ = yld->lcdMap[i]; + *buf++ = '\n'; + *buf = 0; + + up_read(&sysfs_rwsema); + return 3 + ((b - a) << 1); +} + +static ssize_t show_line1(struct device *dev, struct device_attribute *attr, + char *buf) +{ + return show_line(dev, buf, LCD_LINE1_OFFSET, LCD_LINE2_OFFSET); +} + +static ssize_t show_line2(struct device *dev, struct device_attribute *attr, + char *buf) +{ + return show_line(dev, buf, LCD_LINE2_OFFSET, LCD_LINE3_OFFSET); +} + +static ssize_t show_line3(struct device *dev, struct device_attribute *attr, + char *buf) +{ + return show_line(dev, buf, LCD_LINE3_OFFSET, LCD_LINE4_OFFSET); +} + +/* Writing to /sys/../lineX will set the coresponding LCD line. + * - Excess characters are ignored. + * - If less characters are written than allowed, the remaining digits are + * unchanged. + * - The '\n' or '\t' char is a placeholder, it does not overwrite the + * original content. + */ +static ssize_t store_line(struct device *dev, const char *buf, size_t count, + int el, size_t len) +{ + struct yealink_dev *yld; + int i; + + down_write(&sysfs_rwsema); + yld = dev_get_drvdata(dev); + if (yld == NULL) { + up_write(&sysfs_rwsema); + return -ENODEV; + } + + if (len > count) + len = count; + for (i = 0; i < len; i++) + setChar(yld, el++, buf[i]); + + up_write(&sysfs_rwsema); + return count; +} + +static ssize_t store_line1(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + return store_line(dev, buf, count, LCD_LINE1_OFFSET, LCD_LINE1_SIZE); +} + +static ssize_t store_line2(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + return store_line(dev, buf, count, LCD_LINE2_OFFSET, LCD_LINE2_SIZE); +} + +static ssize_t store_line3(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + return store_line(dev, buf, count, LCD_LINE3_OFFSET, LCD_LINE3_SIZE); +} + +/* Interface to visible and audible "icons", these include: + * pictures on the LCD, the LED, and the dialtone signal. + */ + +/* Get a list of "switchable elements" with their current state. */ +static ssize_t get_icons(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct yealink_dev *yld; + int i, ret = 1; + + down_read(&sysfs_rwsema); + yld = dev_get_drvdata(dev); + if (yld == NULL) { + up_read(&sysfs_rwsema); + return -ENODEV; + } + + for (i = 0; i < ARRAY_SIZE(lcdMap); i++) { + if (lcdMap[i].type != '.') + continue; + ret += sprintf(&buf[ret], "%s %s\n", + yld->lcdMap[i] == ' ' ? " " : "on", + lcdMap[i].u.p.name); + } + up_read(&sysfs_rwsema); + return ret; +} + +/* Change the visibility of a particular element. */ +static ssize_t set_icon(struct device *dev, const char *buf, size_t count, + int chr) +{ + struct yealink_dev *yld; + int i; + + down_write(&sysfs_rwsema); + yld = dev_get_drvdata(dev); + if (yld == NULL) { + up_write(&sysfs_rwsema); + return -ENODEV; + } + + for (i = 0; i < ARRAY_SIZE(lcdMap); i++) { + if (lcdMap[i].type != '.') + continue; + if (strncmp(buf, lcdMap[i].u.p.name, count) == 0) { + setChar(yld, i, chr); + break; + } + } + + up_write(&sysfs_rwsema); + return count; +} + +static ssize_t show_icon(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + return set_icon(dev, buf, count, buf[0]); +} + +static ssize_t hide_icon(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + return set_icon(dev, buf, count, ' '); +} + +/* Upload a ringtone to the device. + */ + +/* Stores raw ringtone data in the phone */ +static ssize_t store_ringtone(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct yealink_dev *yld; + + down_write(&sysfs_rwsema); + yld = dev_get_drvdata(dev); + if (yld == NULL) { + up_write(&sysfs_rwsema); + return -ENODEV; + } + + /* TODO locking with async usb control interface??? */ + yealink_set_ringtone(yld, (char *)buf, count); + up_write(&sysfs_rwsema); + return count; +} + +#define _M444 S_IRUGO +#define _M664 S_IRUGO|S_IWUSR|S_IWGRP +#define _M220 S_IWUSR|S_IWGRP + +static DEVICE_ATTR(map_seg7 , _M664, show_map , store_map ); +static DEVICE_ATTR(line1 , _M664, show_line1 , store_line1 ); +static DEVICE_ATTR(line2 , _M664, show_line2 , store_line2 ); +static DEVICE_ATTR(line3 , _M664, show_line3 , store_line3 ); +static DEVICE_ATTR(get_icons , _M444, get_icons , NULL ); +static DEVICE_ATTR(show_icon , _M220, NULL , show_icon ); +static DEVICE_ATTR(hide_icon , _M220, NULL , hide_icon ); +static DEVICE_ATTR(ringtone , _M220, NULL , store_ringtone); + +static struct attribute *yld_attributes[] = { + &dev_attr_line1.attr, + &dev_attr_line2.attr, + &dev_attr_line3.attr, + &dev_attr_get_icons.attr, + &dev_attr_show_icon.attr, + &dev_attr_hide_icon.attr, + &dev_attr_map_seg7.attr, + &dev_attr_ringtone.attr, + NULL +}; + +static struct attribute_group yld_attr_group = { + .attrs = yld_attributes +}; + +/******************************************************************************* + * Linux interface and usb initialisation + ******************************************************************************/ + +struct driver_info { + char *name; +}; + +static const struct driver_info info_P1K = { + .name = "Yealink usb-p1k", +}; + +static const struct usb_device_id usb_table [] = { + { + .match_flags = USB_DEVICE_ID_MATCH_DEVICE | + USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x6993, + .idProduct = 0xb001, + .bInterfaceClass = USB_CLASS_HID, + .bInterfaceSubClass = 0, + .bInterfaceProtocol = 0, + .driver_info = (kernel_ulong_t)&info_P1K + }, + { } +}; + +static int usb_cleanup(struct yealink_dev *yld, int err) +{ + if (yld == NULL) + return err; + + usb_kill_urb(yld->urb_irq); /* parameter validation in core/urb */ + usb_kill_urb(yld->urb_ctl); /* parameter validation in core/urb */ + + if (yld->idev) { + if (err) + input_free_device(yld->idev); + else + input_unregister_device(yld->idev); + } + + usb_free_urb(yld->urb_irq); + usb_free_urb(yld->urb_ctl); + + usb_buffer_free(yld->udev, sizeof(*(yld->ctl_req)), + yld->ctl_req, yld->ctl_req_dma); + usb_buffer_free(yld->udev, USB_PKT_LEN, + yld->ctl_data, yld->ctl_dma); + usb_buffer_free(yld->udev, USB_PKT_LEN, + yld->irq_data, yld->irq_dma); + + kfree(yld); + return err; +} + +static void usb_disconnect(struct usb_interface *intf) +{ + struct yealink_dev *yld; + + down_write(&sysfs_rwsema); + yld = usb_get_intfdata(intf); + sysfs_remove_group(&intf->dev.kobj, &yld_attr_group); + usb_set_intfdata(intf, NULL); + up_write(&sysfs_rwsema); + + usb_cleanup(yld, 0); +} + +static int usb_probe(struct usb_interface *intf, const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev (intf); + struct driver_info *nfo = (struct driver_info *)id->driver_info; + struct usb_host_interface *interface; + struct usb_endpoint_descriptor *endpoint; + struct yealink_dev *yld; + struct input_dev *input_dev; + int ret, pipe, i; + + interface = intf->cur_altsetting; + endpoint = &interface->endpoint[0].desc; + if (!usb_endpoint_is_int_in(endpoint)) + return -ENODEV; + + yld = kzalloc(sizeof(struct yealink_dev), GFP_KERNEL); + if (!yld) + return -ENOMEM; + + yld->udev = udev; + + yld->idev = input_dev = input_allocate_device(); + if (!input_dev) + return usb_cleanup(yld, -ENOMEM); + + /* allocate usb buffers */ + yld->irq_data = usb_buffer_alloc(udev, USB_PKT_LEN, + GFP_ATOMIC, &yld->irq_dma); + if (yld->irq_data == NULL) + return usb_cleanup(yld, -ENOMEM); + + yld->ctl_data = usb_buffer_alloc(udev, USB_PKT_LEN, + GFP_ATOMIC, &yld->ctl_dma); + if (!yld->ctl_data) + return usb_cleanup(yld, -ENOMEM); + + yld->ctl_req = usb_buffer_alloc(udev, sizeof(*(yld->ctl_req)), + GFP_ATOMIC, &yld->ctl_req_dma); + if (yld->ctl_req == NULL) + return usb_cleanup(yld, -ENOMEM); + + /* allocate urb structures */ + yld->urb_irq = usb_alloc_urb(0, GFP_KERNEL); + if (yld->urb_irq == NULL) + return usb_cleanup(yld, -ENOMEM); + + yld->urb_ctl = usb_alloc_urb(0, GFP_KERNEL); + if (yld->urb_ctl == NULL) + return usb_cleanup(yld, -ENOMEM); + + /* get a handle to the interrupt data pipe */ + pipe = usb_rcvintpipe(udev, endpoint->bEndpointAddress); + ret = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); + if (ret != USB_PKT_LEN) + err("invalid payload size %d, expected %zd", ret, USB_PKT_LEN); + + /* initialise irq urb */ + usb_fill_int_urb(yld->urb_irq, udev, pipe, yld->irq_data, + USB_PKT_LEN, + urb_irq_callback, + yld, endpoint->bInterval); + yld->urb_irq->transfer_dma = yld->irq_dma; + yld->urb_irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + yld->urb_irq->dev = udev; + + /* initialise ctl urb */ + yld->ctl_req->bRequestType = USB_TYPE_CLASS | USB_RECIP_INTERFACE | + USB_DIR_OUT; + yld->ctl_req->bRequest = USB_REQ_SET_CONFIGURATION; + yld->ctl_req->wValue = cpu_to_le16(0x200); + yld->ctl_req->wIndex = cpu_to_le16(interface->desc.bInterfaceNumber); + yld->ctl_req->wLength = cpu_to_le16(USB_PKT_LEN); + + usb_fill_control_urb(yld->urb_ctl, udev, usb_sndctrlpipe(udev, 0), + (void *)yld->ctl_req, yld->ctl_data, USB_PKT_LEN, + urb_ctl_callback, yld); + yld->urb_ctl->setup_dma = yld->ctl_req_dma; + yld->urb_ctl->transfer_dma = yld->ctl_dma; + yld->urb_ctl->transfer_flags |= URB_NO_SETUP_DMA_MAP | + URB_NO_TRANSFER_DMA_MAP; + yld->urb_ctl->dev = udev; + + /* find out the physical bus location */ + usb_make_path(udev, yld->phys, sizeof(yld->phys)); + strlcat(yld->phys, "/input0", sizeof(yld->phys)); + + /* register settings for the input device */ + input_dev->name = nfo->name; + input_dev->phys = yld->phys; + usb_to_input_id(udev, &input_dev->id); + input_dev->dev.parent = &intf->dev; + + input_set_drvdata(input_dev, yld); + + input_dev->open = input_open; + input_dev->close = input_close; + /* input_dev->event = input_ev; TODO */ + + /* register available key events */ + input_dev->evbit[0] = BIT(EV_KEY); + for (i = 0; i < 256; i++) { + int k = map_p1k_to_key(i); + if (k >= 0) { + set_bit(k & 0xff, input_dev->keybit); + if (k >> 8) + set_bit(k >> 8, input_dev->keybit); + } + } + + ret = input_register_device(yld->idev); + if (ret) + return usb_cleanup(yld, ret); + + usb_set_intfdata(intf, yld); + + /* clear visible elements */ + for (i = 0; i < ARRAY_SIZE(lcdMap); i++) + setChar(yld, i, ' '); + + /* display driver version on LCD line 3 */ + store_line3(&intf->dev, NULL, + DRIVER_VERSION, sizeof(DRIVER_VERSION)); + + /* Register sysfs hooks (don't care about failure) */ + ret = sysfs_create_group(&intf->dev.kobj, &yld_attr_group); + return 0; +} + +static struct usb_driver yealink_driver = { + .name = "yealink", + .probe = usb_probe, + .disconnect = usb_disconnect, + .id_table = usb_table, +}; + +static int __init yealink_dev_init(void) +{ + int ret = usb_register(&yealink_driver); + if (ret == 0) + info(DRIVER_DESC ":" DRIVER_VERSION); + return ret; +} + +static void __exit yealink_dev_exit(void) +{ + usb_deregister(&yealink_driver); +} + +module_init(yealink_dev_init); +module_exit(yealink_dev_exit); + +MODULE_DEVICE_TABLE (usb, usb_table); + +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/yealink.h b/drivers/input/misc/yealink.h new file mode 100644 index 00000000000..48af0be9cbd --- /dev/null +++ b/drivers/input/misc/yealink.h @@ -0,0 +1,220 @@ +/* + * drivers/usb/input/yealink.h + * + * Copyright (c) 2005 Henk Vergonet + * + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef INPUT_YEALINK_H +#define INPUT_YEALINK_H + +/* Using the control channel on interface 3 various aspects of the phone + * can be controlled like LCD, LED, dialtone and the ringtone. + */ + +struct yld_ctl_packet { + u8 cmd; /* command code, see below */ + u8 size; /* 1-11, size of used data bytes. */ + u16 offset; /* internal packet offset */ + u8 data[11]; + s8 sum; /* negative sum of 15 preceding bytes */ +} __attribute__ ((packed)); + +#define USB_PKT_LEN sizeof(struct yld_ctl_packet) + +/* The following yld_ctl_packet's are available: */ + +/* Init registers + * + * cmd 0x8e + * size 10 + * offset 0 + * data 0,0,0,0.... + */ +#define CMD_INIT 0x8e + +/* Request key scan + * + * cmd 0x80 + * size 1 + * offset 0 + * data[0] on return returns the key number, if it changes there's a new + * key pressed. + */ +#define CMD_KEYPRESS 0x80 + +/* Request scancode + * + * cmd 0x81 + * size 1 + * offset key number [0-1f] + * data[0] on return returns the scancode + */ +#define CMD_SCANCODE 0x81 + +/* Set LCD + * + * cmd 0x04 + * size 1-11 + * offset 0-23 + * data segment bits + */ +#define CMD_LCD 0x04 + +/* Set led + * + * cmd 0x05 + * size 1 + * offset 0 + * data[0] 0 OFF / 1 ON + */ +#define CMD_LED 0x05 + +/* Set ringtone volume + * + * cmd 0x11 + * size 1 + * offset 0 + * data[0] 0-0xff volume + */ +#define CMD_RING_VOLUME 0x11 + +/* Set ringtone notes + * + * cmd 0x02 + * size 1-11 + * offset 0-> + * data binary representation LE16(-freq), LE16(duration) .... + */ +#define CMD_RING_NOTE 0x02 + +/* Sound ringtone via the speaker on the back + * + * cmd 0x03 + * size 1 + * offset 0 + * data[0] 0 OFF / 0x24 ON + */ +#define CMD_RINGTONE 0x03 + +/* Sound dial tone via the ear speaker + * + * cmd 0x09 + * size 1 + * offset 0 + * data[0] 0 OFF / 1 ON + */ +#define CMD_DIALTONE 0x09 + +#endif /* INPUT_YEALINK_H */ + + +#if defined(_SEG) && defined(_PIC) +/* This table maps the LCD segments onto individual bit positions in the + * yld_status struct. + */ + +/* LCD, each segment must be driven seperately. + * + * Layout: + * + * |[] [][] [][] [][] in |[][] + * |[] M [][] D [][] : [][] out |[][] + * store + * + * NEW REP SU MO TU WE TH FR SA + * + * [] [] [] [] [] [] [] [] [] [] [] [] + * [] [] [] [] [] [] [] [] [] [] [] [] + */ + +/* Line 1 + * Format : 18.e8.M8.88...188 + * Icon names : M D : IN OUT STORE + */ +#define LCD_LINE1_OFFSET 0 +#define LCD_LINE1_SIZE 17 + +/* Note: first g then f => ! ! */ +/* _SEG( type a b c d e g f ) */ + _SEG('1', 0,0 , 22,2 , 22,2 , 0,0 , 0,0 , 0,0 , 0,0 ), + _SEG('8', 20,1 , 20,2 , 20,4 , 20,8 , 21,4 , 21,2 , 21,1 ), + _PIC('.', 22,1 , "M" ), + _SEG('e', 18,1 , 18,2 , 18,4 , 18,1 , 19,2 , 18,1 , 19,1 ), + _SEG('8', 16,1 , 16,2 , 16,4 , 16,8 , 17,4 , 17,2 , 17,1 ), + _PIC('.', 15,8 , "D" ), + _SEG('M', 14,1 , 14,2 , 14,4 , 14,1 , 15,4 , 15,2 , 15,1 ), + _SEG('8', 12,1 , 12,2 , 12,4 , 12,8 , 13,4 , 13,2 , 13,1 ), + _PIC('.', 11,8 , ":" ), + _SEG('8', 10,1 , 10,2 , 10,4 , 10,8 , 11,4 , 11,2 , 11,1 ), + _SEG('8', 8,1 , 8,2 , 8,4 , 8,8 , 9,4 , 9,2 , 9,1 ), + _PIC('.', 7,1 , "IN" ), + _PIC('.', 7,2 , "OUT" ), + _PIC('.', 7,4 , "STORE" ), + _SEG('1', 0,0 , 5,1 , 5,1 , 0,0 , 0,0 , 0,0 , 0,0 ), + _SEG('8', 4,1 , 4,2 , 4,4 , 4,8 , 5,8 , 5,4 , 5,2 ), + _SEG('8', 2,1 , 2,2 , 2,4 , 2,8 , 3,4 , 3,2 , 3,1 ), + +/* Line 2 + * Format : ......... + * Pict. name : NEW REP SU MO TU WE TH FR SA + */ +#define LCD_LINE2_OFFSET LCD_LINE1_OFFSET + LCD_LINE1_SIZE +#define LCD_LINE2_SIZE 9 + + _PIC('.', 23,2 , "NEW" ), + _PIC('.', 23,4 , "REP" ), + _PIC('.', 1,8 , "SU" ), + _PIC('.', 1,4 , "MO" ), + _PIC('.', 1,2 , "TU" ), + _PIC('.', 1,1 , "WE" ), + _PIC('.', 0,1 , "TH" ), + _PIC('.', 0,2 , "FR" ), + _PIC('.', 0,4 , "SA" ), + +/* Line 3 + * Format : 888888888888 + */ +#define LCD_LINE3_OFFSET LCD_LINE2_OFFSET + LCD_LINE2_SIZE +#define LCD_LINE3_SIZE 12 + + _SEG('8', 22,16, 22,32, 22,64, 22,128, 23,128, 23,64, 23,32 ), + _SEG('8', 20,16, 20,32, 20,64, 20,128, 21,128, 21,64, 21,32 ), + _SEG('8', 18,16, 18,32, 18,64, 18,128, 19,128, 19,64, 19,32 ), + _SEG('8', 16,16, 16,32, 16,64, 16,128, 17,128, 17,64, 17,32 ), + _SEG('8', 14,16, 14,32, 14,64, 14,128, 15,128, 15,64, 15,32 ), + _SEG('8', 12,16, 12,32, 12,64, 12,128, 13,128, 13,64, 13,32 ), + _SEG('8', 10,16, 10,32, 10,64, 10,128, 11,128, 11,64, 11,32 ), + _SEG('8', 8,16, 8,32, 8,64, 8,128, 9,128, 9,64, 9,32 ), + _SEG('8', 6,16, 6,32, 6,64, 6,128, 7,128, 7,64, 7,32 ), + _SEG('8', 4,16, 4,32, 4,64, 4,128, 5,128, 5,64, 5,32 ), + _SEG('8', 2,16, 2,32, 2,64, 2,128, 3,128, 3,64, 3,32 ), + _SEG('8', 0,16, 0,32, 0,64, 0,128, 1,128, 1,64, 1,32 ), + +/* Line 4 + * + * The LED, DIALTONE and RINGTONE are implemented as icons and use the same + * sysfs interface. + */ +#define LCD_LINE4_OFFSET LCD_LINE3_OFFSET + LCD_LINE3_SIZE + + _PIC('.', offsetof(struct yld_status, led) , 0x01, "LED" ), + _PIC('.', offsetof(struct yld_status, dialtone) , 0x01, "DIALTONE" ), + _PIC('.', offsetof(struct yld_status, ringtone) , 0x24, "RINGTONE" ), + +#undef _SEG +#undef _PIC +#endif /* _SEG && _PIC */ -- cgit v1.2.3