From f1914226e12044f0cacda59efc91bee972c30341 Mon Sep 17 00:00:00 2001 From: Mike McCormack Date: Wed, 23 Sep 2009 03:50:36 +0000 Subject: skge: Make sure both ports initialize correctly If allocation of the second ports fails, make sure that hw->ports is not 2 otherwise we'll crash trying to access the second port. This fix is copied from a similar fix in the sky2 driver (ca519274...), but is untested, as I don't have a skge card. Signed-off-by: Mike McCormack Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/skge.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers/net/skge.c') diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 55bad408196..2bb21ffbde3 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -3982,14 +3982,17 @@ static int __devinit skge_probe(struct pci_dev *pdev, } skge_show_addr(dev); - if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) { - if (register_netdev(dev1) == 0) + if (hw->ports > 1) { + dev1 = skge_devinit(hw, 1, using_dac); + if (dev1 && register_netdev(dev1) == 0) skge_show_addr(dev1); else { /* Failure to register second port need not be fatal */ dev_warn(&pdev->dev, "register of second port failed\n"); hw->dev[1] = NULL; - free_netdev(dev1); + hw->ports = 1; + if (dev1) + free_netdev(dev1); } } pci_set_drvdata(pdev, hw); -- cgit v1.2.3 From 415e69e6574ab740e5db56152055eb899e7ac86e Mon Sep 17 00:00:00 2001 From: Michal Schmidt Date: Thu, 1 Oct 2009 08:13:23 +0000 Subject: skge: use unique IRQ name Most network drivers request their IRQ when the interface is activated. skge does it in ->probe() instead, because it can work with two-port cards where the two net_devices use the same IRQ. This works fine most of the time, except in some situations when the interface gets renamed. Consider this example: 1. modprobe skge The card is detected as eth0 and requests IRQ 17. Directory /proc/irq/17/eth0 is created. 2. There is an udev rule which says this interface should be called eth1, so udev renames eth0 -> eth1. 3. modprobe 8139too The Realtek card is detected as eth0. It will be using IRQ 17 too. 4. ip link set eth0 up Now 8139too requests IRQ 17. The result is: WARNING: at fs/proc/generic.c:590 proc_register ... proc_dir_entry '17/eth0' already registered ... And "ls /proc/irq/17" shows two subdirectories, both called eth0. Fix it by using a unique name for skge's IRQ, based on the PCI address. The naming from the example then looks like this: $ grep skge /proc/interrupts 17: 169 IO-APIC-fasteoi skge@pci:0000:00:0a.0, eth0 irqbalance daemon will have to be taught to recognize "skge@" as an Ethernet interrupt. This will be a one-liner addition in classify.c. I will send a patch to irqbalance if this change is accepted. Signed-off-by: Michal Schmidt Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/skge.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/net/skge.c') diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 2bb21ffbde3..01f6811f132 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -3935,11 +3935,14 @@ static int __devinit skge_probe(struct pci_dev *pdev, #endif err = -ENOMEM; - hw = kzalloc(sizeof(*hw), GFP_KERNEL); + /* space for skge@pci:0000:04:00.0 */ + hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:" ) + + strlen(pci_name(pdev)) + 1, GFP_KERNEL); if (!hw) { dev_err(&pdev->dev, "cannot allocate hardware struct\n"); goto err_out_free_regions; } + sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev)); hw->pdev = pdev; spin_lock_init(&hw->hw_lock); @@ -3974,7 +3977,7 @@ static int __devinit skge_probe(struct pci_dev *pdev, goto err_out_free_netdev; } - err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw); + err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, hw->irq_name, hw); if (err) { dev_err(&pdev->dev, "%s: cannot assign irq %d\n", dev->name, pdev->irq); -- cgit v1.2.3