From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/scsi/fastlane.c | 421 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 421 insertions(+) create mode 100644 drivers/scsi/fastlane.c (limited to 'drivers/scsi/fastlane.c') diff --git a/drivers/scsi/fastlane.c b/drivers/scsi/fastlane.c new file mode 100644 index 00000000000..ae47612b361 --- /dev/null +++ b/drivers/scsi/fastlane.c @@ -0,0 +1,421 @@ +/* fastlane.c: Driver for Phase5's Fastlane SCSI Controller. + * + * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk) + * + * This driver is based on the CyberStorm driver, hence the occasional + * reference to CyberStorm. + * + * Betatesting & crucial adjustments by + * Patrik Rak (prak3264@ss1000.ms.mff.cuni.cz) + * + */ + +/* TODO: + * + * o According to the doc from laire, it is required to reset the DMA when + * the transfer is done. ATM we reset DMA just before every new + * dma_init_(read|write). + * + * 1) Figure out how to make a cleaner merge with the sparc driver with regard + * to the caches and the Sparc MMU mapping. + * 2) Make as few routines required outside the generic driver. A lot of the + * routines in this file used to be inline! + */ + +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "scsi.h" +#include +#include "NCR53C9x.h" + +#include +#include + +#include +#include + +#include + +/* Such day has just come... */ +#if 0 +/* Let this defined unless you really need to enable DMA IRQ one day */ +#define NODMAIRQ +#endif + +/* The controller registers can be found in the Z2 config area at these + * offsets: + */ +#define FASTLANE_ESP_ADDR 0x1000001 +#define FASTLANE_DMA_ADDR 0x1000041 + + +/* The Fastlane DMA interface */ +struct fastlane_dma_registers { + volatile unsigned char cond_reg; /* DMA status (ro) [0x0000] */ +#define ctrl_reg cond_reg /* DMA control (wo) [0x0000] */ + unsigned char dmapad1[0x3f]; + volatile unsigned char clear_strobe; /* DMA clear (wo) [0x0040] */ +}; + + +/* DMA status bits */ +#define FASTLANE_DMA_MINT 0x80 +#define FASTLANE_DMA_IACT 0x40 +#define FASTLANE_DMA_CREQ 0x20 + +/* DMA control bits */ +#define FASTLANE_DMA_FCODE 0xa0 +#define FASTLANE_DMA_MASK 0xf3 +#define FASTLANE_DMA_LED 0x10 /* HD led control 1 = on */ +#define FASTLANE_DMA_WRITE 0x08 /* 1 = write */ +#define FASTLANE_DMA_ENABLE 0x04 /* Enable DMA */ +#define FASTLANE_DMA_EDI 0x02 /* Enable DMA IRQ ? */ +#define FASTLANE_DMA_ESI 0x01 /* Enable SCSI IRQ */ + +static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count); +static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp); +static void dma_dump_state(struct NCR_ESP *esp); +static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length); +static void dma_init_write(struct NCR_ESP *esp, __u32 vaddr, int length); +static void dma_ints_off(struct NCR_ESP *esp); +static void dma_ints_on(struct NCR_ESP *esp); +static int dma_irq_p(struct NCR_ESP *esp); +static void dma_irq_exit(struct NCR_ESP *esp); +static void dma_led_off(struct NCR_ESP *esp); +static void dma_led_on(struct NCR_ESP *esp); +static int dma_ports_p(struct NCR_ESP *esp); +static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write); + +static unsigned char ctrl_data = 0; /* Keep backup of the stuff written + * to ctrl_reg. Always write a copy + * to this register when writing to + * the hardware register! + */ + +static volatile unsigned char cmd_buffer[16]; + /* This is where all commands are put + * before they are transferred to the ESP chip + * via PIO. + */ + +static inline void dma_clear(struct NCR_ESP *esp) +{ + struct fastlane_dma_registers *dregs = + (struct fastlane_dma_registers *) (esp->dregs); + unsigned long *t; + + ctrl_data = (ctrl_data & FASTLANE_DMA_MASK); + dregs->ctrl_reg = ctrl_data; + + t = (unsigned long *)(esp->edev); + + dregs->clear_strobe = 0; + *t = 0 ; +} + +/***************************************************************** Detection */ +int __init fastlane_esp_detect(Scsi_Host_Template *tpnt) +{ + struct NCR_ESP *esp; + struct zorro_dev *z = NULL; + unsigned long address; + + if ((z = zorro_find_device(ZORRO_PROD_PHASE5_BLIZZARD_1230_II_FASTLANE_Z3_CYBERSCSI_CYBERSTORM060, z))) { + unsigned long board = z->resource.start; + if (request_mem_region(board+FASTLANE_ESP_ADDR, + sizeof(struct ESP_regs), "NCR53C9x")) { + /* Check if this is really a fastlane controller. The problem + * is that also the cyberstorm and blizzard controllers use + * this ID value. Fortunately only Fastlane maps in Z3 space + */ + if (board < 0x1000000) { + goto err_release; + } + esp = esp_allocate(tpnt, (void *)board+FASTLANE_ESP_ADDR); + + /* Do command transfer with programmed I/O */ + esp->do_pio_cmds = 1; + + /* Required functions */ + esp->dma_bytes_sent = &dma_bytes_sent; + esp->dma_can_transfer = &dma_can_transfer; + esp->dma_dump_state = &dma_dump_state; + esp->dma_init_read = &dma_init_read; + esp->dma_init_write = &dma_init_write; + esp->dma_ints_off = &dma_ints_off; + esp->dma_ints_on = &dma_ints_on; + esp->dma_irq_p = &dma_irq_p; + esp->dma_ports_p = &dma_ports_p; + esp->dma_setup = &dma_setup; + + /* Optional functions */ + esp->dma_barrier = 0; + esp->dma_drain = 0; + esp->dma_invalidate = 0; + esp->dma_irq_entry = 0; + esp->dma_irq_exit = &dma_irq_exit; + esp->dma_led_on = &dma_led_on; + esp->dma_led_off = &dma_led_off; + esp->dma_poll = 0; + esp->dma_reset = 0; + + /* Initialize the portBits (enable IRQs) */ + ctrl_data = (FASTLANE_DMA_FCODE | +#ifndef NODMAIRQ + FASTLANE_DMA_EDI | +#endif + FASTLANE_DMA_ESI); + + + /* SCSI chip clock */ + esp->cfreq = 40000000; + + + /* Map the physical address space into virtual kernel space */ + address = (unsigned long) + z_ioremap(board, z->resource.end-board+1); + + if(!address){ + printk("Could not remap Fastlane controller memory!"); + goto err_unregister; + } + + + /* The DMA registers on the Fastlane are mapped + * relative to the device (i.e. in the same Zorro + * I/O block). + */ + esp->dregs = (void *)(address + FASTLANE_DMA_ADDR); + + /* ESP register base */ + esp->eregs = (struct ESP_regs *)(address + FASTLANE_ESP_ADDR); + + /* Board base */ + esp->edev = (void *) address; + + /* Set the command buffer */ + esp->esp_command = cmd_buffer; + esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer); + + esp->irq = IRQ_AMIGA_PORTS; + esp->slot = board+FASTLANE_ESP_ADDR; + if (request_irq(IRQ_AMIGA_PORTS, esp_intr, SA_SHIRQ, + "Fastlane SCSI", esp->ehost)) { + printk(KERN_WARNING "Fastlane: Could not get IRQ%d, aborting.\n", IRQ_AMIGA_PORTS); + goto err_unmap; + } + + /* Controller ID */ + esp->scsi_id = 7; + + /* We don't have a differential SCSI-bus. */ + esp->diff = 0; + + dma_clear(esp); + esp_initialize(esp); + + printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use); + esps_running = esps_in_use; + return esps_in_use; + } + } + return 0; + + err_unmap: + z_iounmap((void *)address); + err_unregister: + scsi_unregister (esp->ehost); + err_release: + release_mem_region(z->resource.start+FASTLANE_ESP_ADDR, + sizeof(struct ESP_regs)); + return 0; +} + + +/************************************************************* DMA Functions */ +static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count) +{ + /* Since the Fastlane DMA is fully dedicated to the ESP chip, + * the number of bytes sent (to the ESP chip) equals the number + * of bytes in the FIFO - there is no buffering in the DMA controller. + * XXXX Do I read this right? It is from host to ESP, right? + */ + return fifo_count; +} + +static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp) +{ + unsigned long sz = sp->SCp.this_residual; + if(sz > 0xfffc) + sz = 0xfffc; + return sz; +} + +static void dma_dump_state(struct NCR_ESP *esp) +{ + ESPLOG(("esp%d: dma -- cond_reg<%02x>\n", + esp->esp_id, ((struct fastlane_dma_registers *) + (esp->dregs))->cond_reg)); + ESPLOG(("intreq:<%04x>, intena:<%04x>\n", + custom.intreqr, custom.intenar)); +} + +static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length) +{ + struct fastlane_dma_registers *dregs = + (struct fastlane_dma_registers *) (esp->dregs); + unsigned long *t; + + cache_clear(addr, length); + + dma_clear(esp); + + t = (unsigned long *)((addr & 0x00ffffff) + esp->edev); + + dregs->clear_strobe = 0; + *t = addr; + + ctrl_data = (ctrl_data & FASTLANE_DMA_MASK) | FASTLANE_DMA_ENABLE; + dregs->ctrl_reg = ctrl_data; +} + +static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length) +{ + struct fastlane_dma_registers *dregs = + (struct fastlane_dma_registers *) (esp->dregs); + unsigned long *t; + + cache_push(addr, length); + + dma_clear(esp); + + t = (unsigned long *)((addr & 0x00ffffff) + (esp->edev)); + + dregs->clear_strobe = 0; + *t = addr; + + ctrl_data = ((ctrl_data & FASTLANE_DMA_MASK) | + FASTLANE_DMA_ENABLE | + FASTLANE_DMA_WRITE); + dregs->ctrl_reg = ctrl_data; +} + + +static void dma_ints_off(struct NCR_ESP *esp) +{ + disable_irq(esp->irq); +} + +static void dma_ints_on(struct NCR_ESP *esp) +{ + enable_irq(esp->irq); +} + +static void dma_irq_exit(struct NCR_ESP *esp) +{ + struct fastlane_dma_registers *dregs = + (struct fastlane_dma_registers *) (esp->dregs); + + dregs->ctrl_reg = ctrl_data & ~(FASTLANE_DMA_EDI|FASTLANE_DMA_ESI); +#ifdef __mc68000__ + nop(); +#endif + dregs->ctrl_reg = ctrl_data; +} + +static int dma_irq_p(struct NCR_ESP *esp) +{ + struct fastlane_dma_registers *dregs = + (struct fastlane_dma_registers *) (esp->dregs); + unsigned char dma_status; + + dma_status = dregs->cond_reg; + + if(dma_status & FASTLANE_DMA_IACT) + return 0; /* not our IRQ */ + + /* Return non-zero if ESP requested IRQ */ + return ( +#ifndef NODMAIRQ + (dma_status & FASTLANE_DMA_CREQ) && +#endif + (!(dma_status & FASTLANE_DMA_MINT)) && + (esp_read(((struct ESP_regs *) (esp->eregs))->esp_status) & ESP_STAT_INTR)); +} + +static void dma_led_off(struct NCR_ESP *esp) +{ + ctrl_data &= ~FASTLANE_DMA_LED; + ((struct fastlane_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data; +} + +static void dma_led_on(struct NCR_ESP *esp) +{ + ctrl_data |= FASTLANE_DMA_LED; + ((struct fastlane_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data; +} + +static int dma_ports_p(struct NCR_ESP *esp) +{ + return ((custom.intenar) & IF_PORTS); +} + +static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write) +{ + /* On the Sparc, DMA_ST_WRITE means "move data from device to memory" + * so when (write) is true, it actually means READ! + */ + if(write){ + dma_init_read(esp, addr, count); + } else { + dma_init_write(esp, addr, count); + } +} + +#define HOSTS_C + +int fastlane_esp_release(struct Scsi_Host *instance) +{ +#ifdef MODULE + unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev; + esp_deallocate((struct NCR_ESP *)instance->hostdata); + esp_release(); + release_mem_region(address, sizeof(struct ESP_regs)); + free_irq(IRQ_AMIGA_PORTS, esp_intr); +#endif + return 1; +} + + +static Scsi_Host_Template driver_template = { + .proc_name = "esp-fastlane", + .proc_info = esp_proc_info, + .name = "Fastlane SCSI", + .detect = fastlane_esp_detect, + .slave_alloc = esp_slave_alloc, + .slave_destroy = esp_slave_destroy, + .release = fastlane_esp_release, + .queuecommand = esp_queue, + .eh_abort_handler = esp_abort, + .eh_bus_reset_handler = esp_reset, + .can_queue = 7, + .this_id = 7, + .sg_tablesize = SG_ALL, + .cmd_per_lun = 1, + .use_clustering = ENABLE_CLUSTERING +}; + +#include "scsi_module.c" + +MODULE_LICENSE("GPL"); -- cgit v1.2.3